Search Documents

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

By Federico Pagliacci, Marco Chiarabelli, Salvatore Miranda

The paper describes the adopted technologies and performance controls related to a special geotechnical engineering solution provided within the scope of the Galataport Project, in Istanbul, Turkey. The scheme is the one applied to the new quay of Salipazari, which is a combination of retaining structure and ground improvement, formed by a combi-wall, a reinforced concrete diaphragm wall and a soil improvement by deep soil mixing (Turbojet). The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high profile Project. The results of the in-situ and laboratory tests carried out on the improved soil are also presented. Main discussed points are: • History of Galataport and main Project details. • Design principle and soil condition for the new quay of Salipazari. • Difficulties encountered during execution of DSM. • Preliminary field trial tests conducted to establish the operational parameters, with relevant in-situ and laboratory tests executed. • Preliminary tests on material used for DSM (seawater and CEM IV SR). • Electronic equipment mounted on the rig, which allows the automatic execution of DSM columns. • Final QA/QC tests conducted to verify the performance of DSM, mainly consisting in: coring with relevant laboratory tests on samples (UCS + Es), seismic refraction tomography and seismic cross hole tomography. Correlations between UCS and Es, and between Es and Edyn are also presented. • A cross section of the executed treatment could be inspected on site during excavation. Photos and considerations are also presented.

Jan 1, 2018

By Klaus Pöllath

The Netherlands RandstadRail project makes use of a large range of sophisticated geotechnical techniques to allow a shield driven tunnel to approach the central station of Rotterdam. This paper describes the construction of three deep excavation pits constructed with 1.2 m and 1.5 m thick diaphragm walls. Besides the presentation of the actual diaphragm wall activities special consideration is given to the break-in and break-out situations of the TBM into the deep excavations pits using sealing blocks and partly glass fibre reinforcement in the diaphragm walls.

Jan 1, 2006

By Karen J. Dawson, Francisco Johnson

"Pressure-grouted high strength helical displacement piles are a recently developed pile type that can be useful in conditions where noise or vibrations must be low or where access or clearance is limited. However, there is no information in the literature that can be used to estimate the soil resistance of these piles or production rates. To fill this information need, this paper presents a New Jersey installation case history and the results of static axial and lateral load tests on both pressure-grouted and ungrouted high strength helical piles at the case history site and trial installation locations in New Jersey and Washington State. Piles between 25 and 50 feet long comprised of steel shaft diameters of 4.5, 5.5, and 7 inches with equivalent grout column diameters ranging from 12 to 22 inches were tested. Lateral loads of up to 100 kips and axial compression loads of up to 700 kips were applied. The results of the load tests are compared to predictions of lateral deformation and axial resistance.INTRODUCTIONHelical piles have long been recognized as a useful foundation type in situations where noise and vibrations must be limited, or where there are access or clearance restrictions. Relatively well-documented design methods and torque to capacity correlations have been developed for the most commonly used helical piles, which are relatively small (typically shafts of 6 inches or less) with corresponding low load carrying resistance.With the increased need to construct in congested urban environments, there is incentive to develop helical piles with higher axial resistance. Seismic and other loading conditions also require lateral resistance, which is low for the typically small helical pile shafts. One method of increasing the soil resistance, both axially and laterally and at relatively low cost, is to place grout around the shaft. Injecting the grout under pressure through the hollow helical pipe section and out a grout port or ports located near the toe of the pile has the potential to increase the pile resistance significantly above that which can be achieve by gravity grouting. Not only does the pressurized grout push out against the surrounding soil, but the rotating helix helps to distribute the grout laterally. Unfortunately, little information is available in the literature to help designers estimate the resistance of grouted helical piles in general and none is available regarding pressuregrouted helical piles."

Jan 1, 2016

By Mohammed Sakr

The use of helical piles for permanent foundation applications has become a practical and feasible alternative to the traditional cast-in-place concrete or driven steel piles. Research and development, installation equipment and manufacturing improvements in the helical piling industry have led to this trend. Moreover helical piles are typically smaller in size and weigh less than traditional piles, and require relatively smaller equipment and therefore it is a cost effective option. The latter is a very attractive feature for foundations installed in remote sites across Alaska. This paper presents full-scale pile load test results of helical piles and driven steel pipe piles installed in a site located in Anchorage, Alaska. Four full-scale pile load tests were carried out including two axial compression and two uplift load tests. Both helical piles and driven steel pipe piles were installed and tested at the same site under similar conditions to provide a direct comparison. The results of the full-scale load tests indicate the superior performance of helical piles compared to driven steel pipe piles. This paper describes the pile installation and test setup, presents the test data, and discusses the results.

Jan 1, 2009

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

By Roger A. Archabal, Omar A. Conte, Gustavo Langoni

This international case study focuses on the rigorous geotechnical interaction and results of a soil improvement program utilized to mitigate consolidation settlements of over 1.5 m [5.0 ft]. The extreme settlement results from very deep, nearly normally consolidated clay and the required high floor loading of a new Logistics Park near Bogota, Colombia. The general subsurface conditions consist of very soft clay extending to depths beyond the 50 m [164.0 ft] explored. A required 1.2 m [3.9 ft] thick fill combined with high floor loads resulted in an applied areal load of approximately 7 ton/m2 [1300 psf] (equivalent to about 4.5m [15.0 ft] of fill). Langan recommended performing a test section to validate the initial consolidation settlement calculations and evaluate possible optimization of the prefabricated vertical drain (PVD) spacing and length. The test section sizing was designed to accurately represent the stresses at depth of the future structures. Extreme settlements of over 1.5 m [5.0 ft] in the center and large differential settlements of over 0.6 m [2.0 ft] were measured between the center and corners of the test section over a relatively short test time. Discussion on the methodology, instrumentation, measured results and future optimization are presented. The recommended soil improvement varied from the standard approaches typically utilized in the area. PROJECT LOCATION AND DESCRIPTION The project site is immediately north-northwest of the city of Bogota in the Bogota Valley. The site is bordered with, and has historically been, farming land bordered to the south by the El Rosal-Bogotá highway. The overall site encompasses about 570,000 m2 [141.0 acres] of gross area and about 484,000 m2 [119.6 acres] of net buildable area. The warehouse complex will consist of 10 very large warehouses with footprints ranging from about 15,000 m2 [3.7 acres] to 30,000 m2 [7.4 acres]. The total building area is about 210,000 m2 [51.9 acres] with most of the remaining areas being paved principal drives, truck parking or administrative parking. The topography of the site is relatively flat and close to final grade in roadway areas. However, the warehouse floors will be raised about 1.2 m [3.9 ft] (equivalent to about 2 t/m2 [370 psf] considering engineered fill) to allow for truck docking. In addition, the design floor loads are heavy and estimated to be up to 5 t/m2 [930 psf] and equivalent to about 2.5m [8.2 ft] of fill. Geotechnical conditions at the site are very weak at depths of 50 meters [165 ft] or more, with soft compressible clays comprising the majority of the soil profile. The Bogota Valley is composed in some areas of very deep alluvial deposits. These deposits have been classified as an important challenge and limitation to the development of high/heavy structures such as the project in question for many years (Orozco, 2006). Soft clay deposits have been encountered even beyond depths of 100 meters [328 ft] in some regions of the Bogota Valley (Sanz, 1994). Extreme settlements can be expected if extensive and high permanent loads (above preconsolidation stress levels) are supported in these thick alluvial deposits.

Jan 1, 2018

By Frederick C. Rhyner

This paper describes the design and construction of two high-capacity rock anchors to restrain a supplementary backstay for the Bear Mountain Bridge, which is a suspension bridge spanning the Hudson River about 40 miles north of New York City. The supplementary backstay was installed to relieve a portion of the tension in the southern main cable, which had been creeping in recent years. The two new rock anchors were 1,200 kip capacity each, installed at a batter to depths of 59 feet. This paper describes the subsurface investigation, group capacity analysis, installation and load testing. The rock anchors included strain gages connected to the monitoring system for the bridge. The paper describes the long term strain gage data which shows no change in stress distribution in either anchor.

Jan 1, 2010

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By François G. Bernardeau

Cement-bentonite (C-B) slurry walls have been used for ground water cutoff in deep excavations, contamination containment, and other applications. Hydraulic conductivity is of great concern for cement-bentonite slurry walls. The quality control program usually specifies permeability and strength tests to be performed in a laboratory on samples cast in the field and cured for a certain time. Currently there is no widely accepted in-situ test method for the performance of the constructed slurry wall. A recently constructed cement-bentonite slurry wall in South Carolina included a 200-foot-long test section done in advance of the production of an 8,300 foot-long wall. Intensive tests and investigation were conducted during and after the test section construction: Monitoring piezometers were installed using wet insertion method and packer tests were conducted in boreholes drilled in the post-28-day-cure slurry wall. The permeability measured from the packer tests was about two orders of magnitude higher than the design and the laboratory test values. Additional investigation was performed using a video camera to inspect the borehole walls especially the packer test sections. Test pits were excavated to observe both sides of the cement-bentonite slurry wall. A thorough inspection was conducted to evaluate the integrity of the wall. The lessons learned and issues regarding the disturbance effects of in-situ testing of cement bentonite slurry walls is presented and discussed.

Jan 1, 2008

By R. Heath Forbes

The route of a new, 4-mile long, electrical transmission line passed through residential neighborhoods and commercial areas of a small town in the South Carolina Coastal Plain. The new line consisted of 54 new poles and a one-mile underground section. Most of the new poles were constructed within 50 ft of existing structures, and in some cases, within 8 ft to 20 ft. A widely-space subsurface exploration consisting of 20 cone penetration test soundings indicated the subsurface conditions along the alignment generally consisted of saturated, loose to medium dense, fine slightly silty to silty sand. The pole foundations consisted of 20 to 30 ft long, prefabricated ?caissons? (essentially an open-end pipe pile with a prefabricated connection system at the top) with diameters of 28 to 56 inches. The steel caissons were installed with vibratory pile hammers. To help prevent damage and defend against possible allegations from nearby property owners, vibration and settlement monitoring was performed during all foundation installation activities. Limited structural condition assessments were also performed before and after foundation installation. For 53 of the 54 foundations, the ground vibrations recorded at distances coincident with the nearest structure locations ranged from 0.05 inches per second to 1.46 inches per second. With consideration of the dominant frequency, the majority of these values were below the commonly used USBM vibration limits. For a foundation installation that was only 8 ft from the nearest structure, a peak particle velocity of 3.06 inches per second was recorded, which exceeded the USBM limits. For all cases, the measured ground surface settlement was negligible (i.e., less than ¾ inch). Several spurious claims alleging vibration-induced damage were made, but the monitoring program provided an adequate defense. One claim involving artwork that fell to the floor during foundation installation at a distance of 8 ft from the house was deemed legitimate.

Jan 1, 2011

By Giovanni A. Bonita

The United States Capitol Visitor Center (USCVC) is one of the largest underground structures ever constructed in the Washington, DC, metropolitan area. The 600,000 ft2 (55,750 m2) structure is entirely underground and immediately adjacent to the shallow foundations of the existing U.S. Capitol building. Interior building columns for the USCVC were supported on 186 drilled shafts that varied in diameter from 4 to 9 ft (1.2 to 2.9 m) and in length from 15 to 45 ft (4.6 to 13.7 m). The vast majority of the building utilities were located beneath the basement floor slab. It was decided at the onset of the project to proceed with construction prior to completion of the design drawings, and coordination between the underslab utilities and the drilled shafts had not yet been finalized at the onset of drilled shaft installation. Given depth and location restrictions of the outlets, relocation of the bulk of the utilities was not possible. Almost half of the drilled shafts were affected, leaving redesign as the most feasible remedial solution. The redesign involved adjustments to the shaft length, diameter, and bell. It took place on a case-by-case basis, sometimes only minutes before installation began. Coordination between the field and design team was excellent, and delay associated with the redesign efforts was minimal. In addition, the detailed, high-quality field records kept by both the contractor and field engineers allowed for accurate and fair estimations of the added drilled footage and concrete volumes placed. The additional service fee, which was minimal, was settled quick and fair.

Jan 1, 2006

By Greg Plutko

Laboratory testing has shown that the Marsh Funnel test can be significantly impacted by long-chain polymer entanglement. In general, shorter hydration time leads to more chain entanglement which in-turn, leads to higher marsh funnel values that values seen for longer mixing. This trend makes it very difficult to predict funnel-viscosity on successive days. Data is presented which helps to explain this chain interaction effect on Marsh Funnel data and how it differs from traditional Fann viscosity. The data suggest that this long-chain polymer entanglement occurs more in samples with less hydration time and decreases as hydration time increases. There is also suggestion that higher polymer concentrations have a greater drop-off in marsh funnel viscosity for a given aging length than do lower solids slurries. Fann rheology was shown to be much less impacted by the hydration time of the PHPA polymers than was Marsh Funnel viscosity. This suggests that the Marsh Funnel viscosity is impacted by some aspect of the slurry that does not affect Fann rheology as strongly. It is known from literature that longer-chained polymers have more potential to entangle and our data support the theory that the Marsh funnel viscosity is greatly impacted by this polymer-chain ‘roping’ entanglement.

By Gordon Chen

The Block 37 Chicago Transit Authority (CTA) Tunnel Construction Project was originally designed by STV to connect Blue Line subway in North Dearborn Street and Red Line subway in State Street in the downtown Chicago Area. The project was proposed using tunnel mining techniques combined with steel pipe jacking and fiber glass rebar soil reinforcement. Weidlinger Associates, Inc. (WAI) and Kiewit Construction Company proposed an alternate design using open cut construction technology. WAI designed a complex temporary excavation support system using Soldier Pile Tremie Concrete (SPTC) walls and Soldier Pile Lagging walls supported by cross lot/corner bracing elements. Below the top of the existing tunnel, a top-down construction technique was utilized. A steel temporary traffic decking system at top of the excavation site served as the daily street traffic function as well as the first level of bracing for the support of excavation. The project encountered great challenges of soft clay conditions in downtown Chicago, numerous existing utilities in the excavation site and the requirements of protection for a number of historical buildings nearby as well as the protection of the city streets. The construction was successfully completed at both State Street/Washington Street and Dearborn Street/Randolph Street. The monitoring system showed that ground movement and adjacent building settlement was kept to a minimum during construction.

Jan 1, 2009

By Y. Z. Xu

This paper presents a new dynamic method called Resonant Pile Test (HPT) for evaluating bearing capacity of pile. The basic conception of RPT is given in brief and the measuring system is also introduced. In addition, the influences of the magnitude of exciting force and of the mass of pile cap on test results are discussed. Finally, comparisons between values of bearing capacity given by RPT and by static load tests for a variety of pile types are listed.

Jan 1, 2010

By Shahid Islam, Lucian Bogdan

There is a rapid expansion of world’s infrastructure and simultaneously existing infrastructure is aging. The maintenance of infrastructures has been of particular concern to the engineering community. Monitoring and evaluating the structures have become more significant than ever. Ground anchor is an important part of the structure where it is installed. Unfortunately there are limited testing methods available to assess the force in the pre-stressing steel. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYNA Force sensors have been developed to measure the force in the pre-stressing steel during construction and at any time during the lifetime of the structure. These sensors make use of the magneto-elastic properties of ferrous materials. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. They can be used for bare, epoxy- coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the tendon. It measures the force of the steel element at the location where it is installed and can be recorded manually, automatically, or remotely. The sensor is robust, requires no maintenance and it is expected to have a similar service life to that of the surrounding structure. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. Sensor readings provide a second measurement, in conjunction with the jack pressure gauge, of the post tensioning force during initial testing procedure for ground anchors. This paper describes its application in tie-back and tie-down anchors and force monitoring of retaining walls, bridge abutment and dams where the data were collected manually, automated and remotely. INTRODUCTION Our infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.

Jan 1, 2018

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By Paul Doherty

Expansion of the global piling industry has been coupled with significant research efforts investigating the mechanisms controlling pile capacity. Static pile design has transitioned from total stress approaches toward effective stress design, with associated improvements in predicting pile performance. As a result, the available literature is heavily skewed toward static capacity prediction. However, when considering piles offshore, the majority of loading is not static but highly variable and cyclic in nature. This paper outlines the additional factors that require consideration for cyclic pile design, including elevated loading rates, cyclic displacements and capacity degradation. A review of the literature identified a number of cyclic pile testing programs which are collated in this paper. General trends are established through comparison of the tests within the database and the conditions where cyclic loading is most likely to be a concern are identified. In particular, loading conditions which involve full plastic shear reversals are seen to cause the most extreme cyclic damage, with the degraded capacity as low as 31% of the precyclic static capacity. The underlying mechanisms which can result in cyclic damage are explored, with particular attention given to the pore pressure response, radial stresses, shear transfer and particle reorientation.

Jan 1, 2009

By Wen-Chieh Cheng

Two bored piles with base grouting are loaded axially and the results are used to compare with numerical analyses. One compressive pile with a diameter of 2 meters is drilled through clay deposit and into bedrock to a depth of 13.7 meters. One tensile pile with a diameter of 1.5 meters is drilled through the same clay deposit and into bedrock to a depth of 17 meters. Both piles are installed with monitoring system such as rebar strain meters, concrete strain gauges and extensometers. The monitored data during pile load test are used to obtain average frictional stress (t) a displacement (z) curve, pile tip bearing (q) as well as pile head load (p) and a displacement (s) curve. FLAC3D is used to simulate the pile loading and base grouting. The soil and bedrock are modeled with Mohr-Coulomb. The parameters of the constitutive law are established from soil biaxial tests and rock bore hole deformation tests. The pile is assumed as an elastic body. The interface element is used to simulate the pile/soil interface and pile/rock interface. The numerical results are compared with the pile load test in terms of t-z curve, q-z curve and p-s curve. Finally, the pile base grouting is simulated and the uplift is analyzed. The result from this study is promising and the numerical modeling is successful.

Jan 1, 2006

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010