Search Documents

By F. Mohamm

"Recent changes in regulations and scientific advances concerning selenium bioaccumulation have placed greater importance on non-biological treatment systems for selenium control. Mining wastewater contains hexavalent selenium (selenate) as the predominant aqueous species and possibly small amounts of tetravalent selenium (selenite). Non-biological removal of selenite is accomplished readily and cost effectively by ferric co-precipitation and adsorption using ferric oxyhydroxides sourced from ferric salts or iron anodes in electrocoagulation cells. Selenate on the other hand is difficult to remove. It is often incorrectly assumed that electrocoagulation is suitable for removing both selenite and selenate. Selenate removal efficiency by electrocoagulation is low and the amount of waste residue produced high. In contrast, BioteQ’s Selen-IX™ process removes selenate very efficiently and produces a much smaller amount of stable residue. The process combines selective ion exchange with electro-reduction of selenate in electrocells that physically resemble electrocoagulation cells but are designed and operated differently. This paper summarizes four years of pilot scale demonstration on a wide range of mine waters and discusses the key benefits and limitations of Selen-IX™. The pros and cons of combining ion exchange with electro-reduction in comparison to direct electro-reduction of selenate are also reviewed.INTRODUCTION Selenium in Mining and Mineral Processing Effluents Similar to sulphate and metals, selenium presence in mining and mineral processing wastewater originates from minerals contained in the mined deposits. Therefore, no organoselenium species are typically present in these kinds of waters and inorganic species including selenite (SeO32-), selenate (SeO42) and elemental selenium account for the majority, if not all, selenium present in these streams. Elemental selenium is not always present in mine water but is often contained in smelter wastewater. To comply with new environmental regulations, a successful water treatment plant must remove selenium from all these forms effectively and economically without generating by-products that are difficult to dispose of or manage. Elemental selenium can be dealt with using filtration or gravity separation in clarifiers often assisted by flocculants and/or coagulants. Mine impacted waters typically contain other forms of suspended solids which are removed from water in this way. Once the solids are removed, the selenium species that remain untreated are the dissolved forms. In mining waters this is mostly selenate with small fraction of selenite. In smelter wastewater, the majority could be selenite. It is well established that tetravalent selenium is readily removed from water by using ferric iron co-precipitation at pH > 4 (NAMC SWG, 2010). Ferric hydroxide/ferrihydrite solids act as the adsorbent for tetravalent selenium when it is in one of the ionic forms of biselenite or selenite. This treatment for tetravalent selenium is highly efficient. Therefore, tetravalent selenium removal is generally not an issue and is often easily incorporated into lime neutralization or unit operations such as electrocoagulation used for removing other metals present in mine impacted waters. Another option of dealing with tetravalent selenium is sulphide precipitation in acidic pH which produces SeS2 and can separate selenite from other metals and/or sludge produced at neutral to alkali pH."

Jan 1, 2017

"Ore deposits containing rare earth elements normally contain small amounts of the radioactive elements thorium (Th) and/or uranium (U). These are the naturally-occurring isotopes U238, U235, and Th232 (and associated decay-series daughter products) that are ubiquitous in nature, and that contribute a small percentage of the natural background radiation exposure encountered by humans. The presence of these radioactive materials in the ore deposit creates potential hazards to human health and the environment that must be dealt with properly in the mining, processing, and refining of the ores, as well as management of waste streams and residues. This paper presents an overview of the environmental and safety issues associated with U and Th, with particular emphasis on rare earth mining, processing, and refining projects; the regulatory approaches followed to ensure that rare earth deposits are developed, operated, closed, and decommissioned safely; and the development of information during the project predevelopment work and permitting processes that feed into the design, operation, and closure of tailings impoundments and milling/separation/refining facilities. Case studies will be presented subject to the availability of relevant public information. INTRODUCTIONNearly all ore deposits containing economically-recoverable rare earth minerals also contain small amounts of the radioactive isotopes for the elements thorium (Th) and/or uranium (U) and their associated radioactive decay products. Therefore, the handling and management of these materials in mining and mineral processing operations must be performed so that workers and the environment are protected from harm from Th and/or U (and their radioactive decay products), just as they must be protected from any other potentially harmful constituents present in the ore or introduced in processing. Examples of these might include ores with high sulfide content, which may pose a risk of acid rock drainage, or chemicals used in ore processing and metals production.The purpose of this paper is to present information on how rare earth mining and processing projects with ores containing Th and/or U can be developed, operated, and decommissioned safely according to applicable regulations intended to protect worker health & safety and the environment.It should be noted that some countries are considering developing Th as a feedstock for producing nuclear energy, which could have some effect on future development of rare earth ore deposits. To avoid confusion, that issue is not discussed in this paper."

Jan 1, 2012

By T. P. Johnson, A. Vathavooran

"Conventional mining operations can produce a wide range of wastes containing gold and other precious metals but which are less suitable for processing by traditional methods. There are also types of ore that do not fit easily into a traditional processing flowsheet, e.g. because the refractory nature of their minerology or the combination of valuable metals is less suitable for traditional processes. Nevertheless, these potential sources of valuable metals remain unexploited resources that have attracted growing interest in the metals and mining industries over recent years. The challenge is therefore to develop and use alternative processing methods that have the flexibility of operation to cope with a wide variety of material types and tonnages, whilst providing high recoveries for valuable metals. Tetronics’ DC plasma smelting technology achieves industry-leading recovery rates for precious metals from a wide range of input materials and initial precious metal concentrations, whilst generating an inert slag-based material as a by-product (even when starting from a hazardous waste input material), approved within the EU for use in construction applications. This paper describes how this technology can be used as a key part of an overall process for the recovery of precious metals from these interesting materials.INTRODUCTION The extraction of gold from its ores by various forms of cyanide leaching has been practised by the mining industry for over a century (Minerals Council of Australia, 2005) and it remains the primary extraction method in a wide range of mining operations. The ability of cyanide to extract gold efficiently and quickly from lower grade ores without extensive additional processing, coupled with well-known methods to recycle the cyanide for re-use within the process mean it is often both the most economically preferable and environmentally acceptable method for recovering gold. As a result, 88% of all gold produced from mines in the USA in 2014 was recovered via leaching of open heaps or dumps (UGGS, 2016). Nevertheless, there are occasions where certain combinations of mineralogy and other circumstances reduce the effectiveness of cyanidation techniques, so that ever more elaborate additional processing steps are required, with inevitable increases in operating costs (Swash, 1988). In these circumstances, which are likely to be more common in future as ore qualities diminish, other methods of extraction may offer better alternatives. Whilst much less commonly used for Au extraction at present, pyrometallurgical methods are amongst the longest-established of these alternative approaches and merit serious consideration in such cases."

Jan 1, 2017

By M-d-N. Gagnon, P. Okono, Y. Bergeron

In the mining industry, decisions regarding the type and number of comminution tests to be completed typically rely on geologists? observations and conclusions when studying drill cores. Given that these decisions are based on visual observations, they are essentially approximate and often inaccurate from a comminution viewpoint, causing a sizeable margin of error in estimating characterization test needs. Consequently, companies are often forced to perform more tests than necessary, requiring a significant quantity of material, and accruing significant costs. Recently, a new device, called the Hardness Index Tester (or HIT), was developed, offering users a low cost in-house mechanism for estimating the comminution parameter A*b and the Bond Ball Mill Work Index at any mine site, with potential applications on fragments up to 25 mm from drill core. In late 2016, Agnico Eagle Mines Limited initiated a trial to investigate if having an HIT device installed in a core repository would make it possible to identify the different rock properties more accurately and determine the number and type of comminution tests required. The application of the HIT was not to replace the standard comminution tests, but rather to generate a high number of comminution and geomechanical parameters for the rock mass. Ultimately, the objective would be to determine the uniformity of the rock mass and, therefore, easily distinguish any potentially problematic zones. With this method, the appropriate number of standard tests could be determined, making the HIT not only an excellent complement to the standard laboratory tests, but also an indispensable device for a geometallurgical characterization. This paper presents the results from the HIT trial using samples from the Odyssey Project, which is a Mine Canadian Malartic property.

Jan 1, 2017

By T. D. Chatwin

While new jobs and taxes are major incentives for support of mining, stakeholders must also be assured that current jobs, resources and environment will be protected. Mining companies can help achieve stakeholder support by frankly addressing Acid Rock Drainage CARD) issues. To prevent ARD, miners must begin early in the mine life-cycle to develop an ARD management plan and integrate it into the mining operation. As this proactive preventative program is initiated, mining companies also need to engage and collaborate with stakeholders to insure that their expectations and needs are met. Stakeholder engagement is enhanced as mining companies emphasizes the value of clean and available water for current and future generations.

Jan 1, 2011

By Alessandro Navarra, Amir Arash Rafiei, Kristian Waters

Mathematical programming (MP) is fundamental to systems engineering and operations management, but has not been widely adopted by mineral processors. The current paper presents an interdisciplinary approach, using MP to incorporate basic notions of mass balancing into an optimization framework. The optimization is typically related to economic profitability. Two- and three-product formulas are extended to give formal descriptions of alternate modes of operation, and a global representation of the concentrator. At this global level, the framework may assist plant managers to make tactical decisions based on incoming feed data. The MP framework is demonstrated through sample calculations describing a lead-zinc concentrator.

Jan 1, 2015

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

"This paper discusses the aspects of tracking cutters related to the computer-aided design of shearer drums. A comprehensive computer analysis of drum dynamic parameters for multi-tracking tool arrangement is not presently available, as the current computer programs mainly consider the aspects of single tracking. Despite the fact that the single-tracking arrangement is recommended for efficient cutting, some major drum manufacturers have been seen to persistently adhere to multi-tracking, probably due to a lack of information. Further studies in this field are believed to contribute greatly to the current understanding of the computer-aided design of shearer drums.A number of laboratory simulation trials and long-term underground investigations were carried out in detail on tracking cutter arrangement, and an equation required for a computer program was derived. The results obtained from computer assessment of dynamic parameters for drums with multi-tracking arrangement were found to be in accordance with those of the underground trials, indicating the validity of the equations. The procedure adopted for the computer appraisal of the shearer drums designed with a multi-tracking concept, as described in this study, is therefore recommended to be considered in the currently employed computer programs."

Jan 1, 2003

By R. D. Browns

In his Budget Speech on March 31, 1 977, the Honourable Donald S. Macdonald expressed concern about the financing of investments through new equity issues. He mentioned the need to render more attractive participation in the equity market by investors in all in come brackets. One of the measures introduced in the budget to accomplish this goal is the proposal to increase the dividend gross-up and tax credit in respect of most dividends received by an individual from Canadian companies. The following comments and tables serve to illustrate the impact of this particular proposal.

Jan 1, 1977

By Noel Brien, O&apos

General: National Asbestos Mines Limited has operated an asbestos mine and mill near Thetford Mines, Quebec, since 1958. As a result of additional exploration of the orebody in 1962-63, it became apparent that long-range mining plans would have to be revised to allow for a large increase in both ore and waste tonnages. It was decided that the task of checking out possible mine designs could best be analyzed by a computer to obtain data from which an optimum open-pit configuration could be plotted. Object: It was desired to arrive at an optimum open-pit configuration with an over-all pit slope of 45 degrees and a minimum operational width of 200 ft. at the bottom. Calculations were based on assay values from diamond drill holes in cross sections of the mine. The computer's assignment was to select and describe, by coordinates, the optimum cross section for the mine. Mine engineers then assembled the various optimum sections to produce the pit outline. As this would not necessarily result in a practical mining arrangement, the computer also provided alternate solutions,

Jan 1, 1965

By Lewis Finch

Oil and .gas reservoirs exist under pressure within the pore spaces of rock structures or traps. Wells are drilled to produce these reservoirs. Under primary operation, the natural energy of expanding fluids in and adjacent to the reservoir forces or drives oil and gas to the wells. There are three basic sources of energy: dissolved gas, water, and gas cap. Typical recovery by primary methods is only 10 to 25 per cent of the oil in place for the dissolved gas drive but is generally higher for the others. Secondary recovery involves the injection of water or gas to supplement natural energy, thereby increasing recovery over that obtainable by primary operation alone. In many cases ultimate recovery with secondary methods is 1.2 to 2.0 times the expected primary recovery. The type programme adaptable in a field depends on its 'primary performance and on certain reservoir characteristics. In the United States, application of secondary recovery methods is becoming increasingly important. About 22 per cent of United States oil production now comes from fields in which injection projects are operating. In 1953, nearly 1.4 million barrels of oil daily came from such fields, more than double the amount in the early 40's. Ultimate primary recovery from known pools is estimated at roughly 73 billion barrels. Secondary recovery projects already in operation will increase this to almost 80 billion, an increase of almost 10 per cent. Unitized secondary recovery projects have been very successful. From unitized projects alone, industry reserves of oil in the United States have been increased by 3 1/2 billion barrels. In Canada, secondary recovery has not been so wide spread mainly because D-3 reef reservoirs which have held the major reserves are under water drive. However, appreciable amounts of water are being injected in the Redwater D-3, Leduc D-2 and Joarcum Viking reservoirs, and gas in the Golden Spike D-3. In both countries, possible achievements in increased recovery through secondary recovery methods now in use and by new ones which may be developed through research and field trial are a challenge to the scientist and the industry.

Jan 1, 1956

By David S. Robertson, Richard F. Douglas

"Uranium is a lithophile element of relatively low natural abundance. Concentrations of uranium form through processes of erosion and sedimentation, and over 90 per cent of the western world's uranium ore reserves are in sedimentary rocks.Proterozoic quartz-pebble conglomerates contain about 60 per cent of the known uranium reserves. These are all similar in appearance, in mode of distribution and in manner of origin. They carry uranium minerals and/or gold and abundant pyrite. Their unique distribution in Huronian time required a pre-existing crust well enough evolved to have plentiful quartz and abundant gold, uranium and pyrite. The materials of value were deposited as detrital heavy minerals prior to the appearance of an oxidizing atmosphere in late Proterozoic time.Epigenetic uranium deposits occur in arkosic sedimentary rocks through the entire geological column. About 30 per cent of the western world's known ore reserves are in _these rocks. This type of deposit is particularly prominent in semi-arid parts of the United States, having yielded most of the uranium ore produced and containing nearly all of the known reserves.The Western States type"" of deposits occur in lenticular, permeable stream-laid sedimentary rocks. The de-posits are believed to have been precipitated from moving ground water at locations where plant debris or other organic matter had accumulated. The uranium may be derived from volcanic sediments, which are commonly associated with the units containing the ore, or it may be leached from exposed granite surfaces or from granitic debris which forms the sediments.A significant part of the world's uranium resources are in black shales and lignitic rocks. The lignites that contain uranium are virtually valueless as potential sources of heat. Uranium concentrations at levels such as to be potential sources of by-product uranium occur in many phosphorites.Reworked sediments may provide uranium in pegmatites and vein-like deposits."

Jan 1, 1970

? A BARGE WILL BE INSTALLED IN THE BOTTOM OF A COMPLETED PIT. ? THE PROVEN BAUER CUTTER TECHNOLOGY WILL BE INSTALLED ON THE BARGE AND A DEWATERING PLANT WILL BE INSTALLED NEAR THE BASE OF THE PIT RAMP. ? THE WATER LEVEL IN THE PIT WILL BE RAISED BY 20- 40 METRES AND REMAIN CONSTANT OVER DURATION OF MINING. ? THE CUTTER WILL BE LOWERED TO MINE 10 METRE DEEP BENCHES ON A CHECKERBOARD PATTERN TO AN ULTIMATE DEPTH OF 200 METRES. ? THE 5? MINUS CUTTINGS WILL BE PUMPED TO THE DEWATERING PLANT, DEWATERED, AND TRUCKED TO SURFACE.

May 1, 2003

By P. L. Richard

An open pit a mine can be thought of as a business unit, with capital, operating and maintenance costs that exceed those of many large business enterprises. Truck-and-shovel operations have an inherent ?looseness? to them, unlike manufacturing or processing operations where production components are tightly coupled (through conveyors, material flow in pipes, assembly lines, and so on). Effective monitoring and control of truck-and-shovel operations requires a combination of both information systems and performance management. Production monitoring systems can impact operations at three levels: minute-by-minute decisions during the shift, procedures, and policies. The technology of production monitoring ranges from real-time data collection to manual entry of time card data into a computer. Time card information is too coarse to effectively manage a multi-million dollar fleet of mobile equipment, so a higher level of production monitoring is required. People issues affect whether the implementation will be a success or a disappointment. Considerations that affect the people issues are discussed, including common obstacles, and key success factors. A balanced scorecard approach must be used, since uni-dimensional measures of performance like tons produced give no indication of whether the production was achieved at the expense of another factor.

May 1, 2004

By P. L. Richard

An open pit a mine can be thought of as a business unit, with capital, operating and maintenance costs that exceed those of many large business enterprises. Truck-and-shovel operations have an inherent “looseness” to them, unlike manufacturing or processing operations where production components are tightly coupled (through conveyors, material flow in pipes, assembly lines, and so on). Effective monitoring and control of truck-and-shovel operations requires a combination of both information systems and performance management. Production monitoring systems can impact operations at three levels: minute-byminute decisions during the shift, procedures, and policies. The technology of production monitoring ranges from real-time data collection to manual entry of time card data into a computer. Time card information is too coarse to effectively manage a multi-million dollar fleet of mobile equipment, so a higher level of production monitoring is required. People issues affect whether the implementation will be a success or a disappointment. Considerations that affect the people issues are discussed, including common obstacles, and key success factors. A balanced scorecard approach must be used, since uni-dimensional measures of performance like tons produced give no indication of whether the production was achieved at the expense of another factor.

Jan 1, 2004

By B. Panton, J. Carvalho, E. T. Brown

High-capacity, post-tensioned anchors have found wide-spread use in initial dam design and construction, and in the strengthening and rehabilitation of concrete dams to meet modern design and safety standards. Despite the advances that have been made in rock mechanics and rock engineering during the almost 80 years in which post-tensioned anchors have been used in dam engineering, some aspects of the rock engineering design of high-capacity rock anchors for dams have changed relatively little over the last 30 or 40 years. This applies, in particular, to the calculations usually carried out to establish the grouted embedment lengths required for deep, post-tensioned anchors. These calculations which involve a number of aleatory and epistemic uncertainties, usually make simplified assumptions about the distribution and values of rock-grout interface shear strengths, the shape of the volume of rock likely to be involved in uplift failure under the influence of a system of post-tensioned anchors, and the mechanism of that failure. The resulting designs are generally conservative. These aspects of the rock engineering design of large, post-tensioned rock anchors for dams could be improved by making greater use of modern, comprehensive, numerical analyses in conjunction with 3D models of the rock mass structure, realistic rock and rock mass properties, and the results of prototype anchor tests in the rock mass concerned.

Jan 1, 2015

By T. E. W. Nind

"A short description of the chamber lift method for producing oil wells is followed by some comments on compressor requirements and gas utilization. A quantitative analysis of the process is presented and, based on this analysis, criteria are suggested for selecting wells for which this type of lift might be suitable. The analysis leads to the conclusions that chamber lift is an efficient producing mechanism for wells having very low productivity indices (say about 0.05 bbl/d/ p.s.i. or less), but that for such wells optimum utilization of injection gas cannot be attained. It is suggested that the gas injection time per cycle should be kept as low as possible, compatible with a small oil fallback volume, and that the cycle frequency should be in the range of 20-40 cycles/ day. For wells with productivity indices of 0.2 bbl/d/p.s.i. or higher, chamber lift is relatively inefficient; how-ever, if well allowables are low it may offer an attractive, low cost, alternative to gas lift or pumping."

Jan 1, 1960

By David Laing

Completion of a Feasibility Study represents a major milestone in the development path of a mine, and one which typically triggers a need for project financing. Obtaining funding for construction relies on a positive Feasibility Study and a host of other related activities. This paper looks at the financing process and work required to support it, during and after the Feasibility Study, and bring it to a successful closing. It will include comment on the significance of permits, environmental plans, construction contracts, offtake arrangements, hedging, insurance, and others requirements to support a financing plan.

May 1, 2010

By V. N. Mackiw, H. Veltman

"A process is described which permits the separate recovery of lead and zinc from complex low-grade sulphide concentrates such as are produced from the New Brunswick type of disseminated pyrite ores. This process calls for the preparation of a lead-zinc bulk concentrate from the original ore by flotation. The bulk concentrate is then oxidized under pressure in autoclaves in aqueous sulphuric acid solution, such as return electrolyte from zinc electrolysis. This yields a zinc sulphate solution and a residue containing lead sulphate, unaltered pyrite and elemental sulphur generated during the oxidation. After the oxidation, the leach slurry is briefly heated to above the melting point of elemental sulphur and then cooled. Thus, pellets containing pyrite and elemental sulphur are formed, and they are separated from the lead sulphate by screening and/or flotation. Laboratory tests have shown that about 95 per cent of the zinc and lead can be separately recovered from complex bulk concentrates. Process possibilities are discussed."

Jan 1, 1967

By B. Krysa, J. Qiu

The zinc pressure leach plant at HBM&S's operations is now in its fifteenth year of operation. Current pressure leach operation is steady at a concentrate processing rate of around 26.5 tonnes per hour. A new cellhouse with a design capacity of 124,000 tonnes per annum and the capability of expansion of up to 154,000 tonnes per annum was commissioned in July 2001. The potential to expand the capacity of the pressure leach circuit and associated processes, as well as the purification circuit and casting plant, to meet the maximum capacity of the cellhouse has been investigated. This paper reviews current operation of the zinc plant, as well as the possibility of a capacity increase without major process modifications or major capital expenditures.

Jan 1, 2008

The Beginning ! The status quo simply isn?t sustainable ! Our social license is at risk ! The bar keeps rising ? We must improve our performance, both operational and social ? We must improve stakeholder judgement of our industry by taking action collectively Implementing TSM " TSM Guiding Principles " Performance Indicators " Crisis communications " External Outreach " Tailings management " Energy management " Performance manuals, guides " Reporting " Communities of Interest Advisory Panel

May 1, 2004