Search Documents

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By Mohamed Ourriban, Yongjun Peng, Qi Liu, Denis Cotnoir

"In the flotation of fine particles, there are two difficulties in general: low recovery of valuable minerals and high recovery of gangue minerals. The low recovery of fine valuable minerals is attributed to low bubble-particle collision and attachment efficiencies, while high recovery of fine gangue minerals is attributed to mechanical entrainment through water films between gas bubbles. Over the last five years COREM has been actively developing fine particle flotation techniques with the objective of improving fine particle flotation separation efficiencies.The fine particle flotation techniques with both generation of micro bubbles and enlargement of sizes of fine particles have been developed to increase bubble-particle collision efficiency. For oxidized fine sulphide minerals, both physical and chemical techniques have been developed to modify the hydrophilic surfaces and therefore increase bubble-particle attachment efficiency. To reduce mechanical entrainment of fine gangue minerals, a new approach, polymeric depression and flocculation, has been developed. By selecting the high molecular weight polymeric depressants to make fine gangue minerals hydrophilic and also enlarge their sizes, entrainment can be minimized. By combining these techniques, we are able to improve both flotation recovery and selectivity in some fine ore flotation systems.INTRODUCTIONWith depleting mineral resources and their declining grades, ores leaving grinding circuit for froth flotation are becoming increasingly finer to achieve mineral liberation. Together with the increasing demand for minerals, ever-increasing tonnages of fines are being produced. Therefore, flotation of fine particles is an immense challenge to be tackled by researchers all over the world today."

Jan 1, 2006

By A. P. E. Dirige

Extensive field study has been performed to assess the capabilities of thin sprayon liners (TSLs) and conventional spray-on support systems for preventing rock and support material damage that often results due to mining-induced rockbursts. Support performance was studied using field scale explosive detonation trials to simulate dynamic failure effects that are known to develop during typical rockburst events. Multiple seismic and high speed photographic monitoring techniques were used to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion, and support liner survivability characteristics. Results of this study have demonstrated that TSL?s and variant layer combinations may be as effective as or better than conventional support materials for mitigating rockburst or like damage in highly stressed mine environments. In this study, field results have been verified using numerical modeling procedures to better understand the support behaviour of TSLs when subjected to highly stressed mine environments and mining-induced rockbursts, a factor that is essential when designing any rock support system. A series of numerical modeling assessments were conducted using FLAC3D modeling of a half circular TSL-lined tunnel, influenced by anisotropic stresses and simulated mining-induced rockbursts, to investigate the support potential of TSLs under prototype conditions. The effect of a mine rockburst was simulated using the three-dimensional dynamic analysis option of FLAC3D. Results of TSL-lined tunnels in highly stressed and mine rockburst conditions indicated exceptional effectiveness of TSLs for suppressing rock deterioration resulting from stresses and rockbursts. The rock support potential of TSLs on tunnel surfaces was compared with that of thin shotcrete linings, and results indicated that thin spray-on lining products currently available may be equally as effective in support as shotcrete materials.

May 1, 2009

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010

By R. W. Lawrence

"Biological leaching can be used to enhance the recovery of gold and silver from refractory ores, concentrates and tailings. The method liberates precious metals associated with sulphide minerals such as pyrite and arsenopyrite making them amenable to cyanidation. The chemistry and features of biological preoxidation leaching is discussed. A summary of the results obtained on various ores, concentrates and tailings is presented.INTRODUCTIONRefractory precious metal ores in which gold and silver are finely disseminated in sulphide minerals such as pyrite and arsenopyrite are becoming more important to the mining industry. This is due both to a depletion of simpler, free-milling ores and to a significant increase in the price of gold in recent years. Whereas many ores can be directly cyanided with gold solubilizations over 90% obtained, the refractory ores respond poorly to direct cyanidation and require decomposition of the precious metal-bearing sulphide minerals to increase recoveries.Decomposition of sulphides by oxidation prior to cyanidation can be carried out by several means. The oldest method is roasting which removes unwanted ore constituents by high temperature oxidation and volatilization. In Canada, for example, roasting is used at Giant Yellowknife (Connell and Cross, 1981). Another method gaining increasing acceptance is pressure hydrometallurgy which uses aqueous oxidation conducted at high temperature and pressure. Homestake Mining Company have recently completed construction of a plant incorporating pressure oxidation at their Mclaughlin property in California (Guinivire, 1984)."

Jan 1, 1985

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By Elizabeth Wademan

Recessions Eventually End ??Companies aggressively cutting production and inventories ??these will come in-line with demand ??U.S. home inventories are declining ??Housing becoming more affordable ??Global trade recovering after collapsing ??Lower oil prices should act as a stimulus Protracted Deleveraging Process Beginning ??Era of leverage-driven consumption is over ??Greatest destruction of consumer wealth since WWII ??Consumers will no longer be able to substitute capital gains for savings ??Shift towards savings will be a headwind to economic growth ???Paradox of Thrift?

May 1, 2009

By Rudy Tenbergen, Dick Farmery, Jim Naylor

"Paste backfill has replaced cemented rock fill as one of the components to improve ground · control and mine safety at the Macassa Operation of Kinross Gold Corporation in Kirkland Lake, Ontario. It is the first operation to utilize "" flash thickening ""of very fine gold tailings to a paste consistency in the ""Paste Production and Storage Mechanism"", a joint technical development of Inco and GL&V. The tailings paste is mixed with alluvial sand to produce an engineered quality paste backfill. The development leading up to the decision to proceed with this novel technology is discussed, as well as commissioning of the backfill operation.IntroductionThe occurrence of a major rockburst on November 23, 1993 prompted a review of mining and backfill procedures at the Macassa No 3 shaft . This shaft is some 7238 ft deep and lies in a mining belt that is prone to seismic events. The recommendations were to change the mining from underhand cut and fill to mechanized long hole stopping and to look at alternatives to the rockfill backfill system in place. The Macassa cemented rock backfill operation, while producing the desired fill stiffness had drawbacks as compared to paste fill. With paste fill, placement rates are faster, more openings can be filled, it is less expensive and less prone to the occurrences of compensable incidents.Macassa mining personnel visited the Sudbury operations of Inco in 1993, where development on paste backfill was in progress. As some of the R&D was taking place with funding from the Premier's Council Technology Fund of the Ministry of Trade and Technology of the Province of Ontario , Inco personnel at that time did some feasibility and conceptual consulting on the use of paste fill for the industry. Inco had developed the use of alluvial sand paste fill, an engineered blend of alluvial sand and tailings fines and was doing development work to eliminate the ""conventional"" way of producing paste from mill tailing by thickening and filtration. This latter development work was taking place with GL&V Ontario. That work led to the filing of a joint Inca/ GL&V patent application for the PPSM, the Paste Production and Storage Mechanism with all marketing rights being held by GL&V."

Jan 1, 1997

By D. Wolfe, K. Reid, T. Nunn

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. In order to minimize front-end rejects, and to allow for high throughput, the ore top size at Aurora has been set at a nominal 125 mm. These relatively large lumps have a significant effect on both pump performance and pipeline pressure gradient. Current design methods underestimate the solids de-rating effect of lumpy slurries in pumps, and do not accurately describe the distribution or magnitude of the lump effect on pipeline pressure gradient. Data from the Aurora hydrotransport systems has been compiled, to quantify the effect of lumps on the pump head ratio and pipeline pressure gradient, and how this effect changes as lump ablation occurs along the length of the pipeline. A model has been built, using a logarithmic curve, which predicts the effect of 125 mm lumps on pipeline pressure gradient as a function of velocity and the distance from the start of a hydrotransport pipeline. This model is applicable only to Aurora hydrotransport operation, but similar models could be developed for other operations using the same methods. Using accurate pipeline pressure gradients and pump head ratios when designing future hydrotransport pipeline systems will help improve their reliability and operability."

Jan 1, 2014

By R. A. Bergman

"Process descriptions are provided for the following ten plants that treat high-magnesia lateritic nickel ores (saprolite) by pyrometallurgical means: PT Aneka Tambang; Cerro Matoso S.A.; Falconbridge Dominicana C. por A.; Hyuga Smelting Company Ltd.; Larco (Societé Minière & Métallurgique de Larymna); Loma de Niquel; Le Nickel, SLN-Eramet; Nippon Yakin Kogyo Company Ltd.; Pacific Metals Company Ltd.; and PT Inco Indonesia.Flowsheets, equipment information,chemistry and production data have been compiledfor plants based on both information providedby the companies and on calculated massand energy balances.IntroductionNickel is of vital importance to modern society. Without it, we would not be able to enjoy many of the things that we take for granted, such as computers, airplanes and stainless steel appliances in our homes and workplaces, to mention a few.Nickel occurs in nature both as sulphide and oxide ores. Approximately 36% of the nickel reserves in the Western World occur as sulphide and 64% as oxide ores. Sulphide ores respond to concentration processes, whereas, oxide ores do not. Sulphide ores mined at 1% nickel can be readily concentrated to 10% nickel, whereas, oxide ores cannot be concentrated and therefore have to be processed as mined.Laterite ores are normally classified intotwo groups:1. The high-magnesia ores, saprolites or serpentines, are, as a rule, processed by smelting. The main reason for this is that the nickel replaces magnesium in the magnesium-silicate lattice. To be able to recover nickel, the lattice has to be destroyed. This can be achieved by smelting under reducing conditions.Acid leaching is also possible, but in this case, large amounts of MgSO4 or MgCl2 will be produced making it costly to regenerate the acid.2. The high-iron, low-magnesia ores are known as limonite. The nickel is relatively loosely bonded to goethite and hence can be recovered by selective reduction followed by ammonium-ammonium carbonate leaching. In recently developed processes, these ores are also being extracted by acid pressure leaching, with high Ni and Co recoveries.This paper focusses on the production of ferronickel and nickel matte from the highmagnesia ores."

Jan 1, 2003

By G. H. Babcock, D. A. Knight, V. G. Medina

"Production commenced at the Golden Sunlight Mine in 1983 and at Kidston Gold Mine in 1985. These projects were both constructed under the management of the Placer Dome Inc. (Technical Services) group of Vancouver, B.C.Golden Sunlight uses a conventional rod mill/ball mill grinding circuit while Kidston uses a SAG /ball mill, and later on, SABC circuit. Since the hardness of the ore and the fineness of the primary grind in both mines are about the same, a meaningful cost comparison can be made. The comparison is made on the basis of capital and operating costs.The result of this study indicates that a significant capital cost savings can be achieved in favour of the SAG /ball mill circuit when the ore is amenable to semi-autogenous grinding. With a good maintenance program, the operating cost for the SAG /ball mill circuit could also be lower that the conventional rod mill/ball mill circuit.HISTORYGolden Sunlight MineGolden Sunlight is a 5 530 t/d gold mine located near Whitehall, a small town 60 km east of Butte, Montana. Originally optioned by PDI U.S. in 1958, the development of the property waited until 1981 when economic conditions became favorable for the project to proceed.Semiautogenous grinding tests were conducted during the final stages of the feasibility study. The hard near surface ore was not quite amenable to semi-autogenous grinding. The best result produced from a series of tests using a 1.83 m diameter mill was a semiautogenous work index of 39. This is substantially higher than the 22 Bond work index of the sample used in the testwork. A conventional SAG/ball mill circuit for this ore will be extremely inefficient, and for this reason, this circuit was rejected in favour of a conventional rod mill/ball mill circuit."

Jan 1, 1991

By E. Bongajum

We present results from petrophysical studies to characterize a Zn-Pb-Ag deposit in Nash Creek, New Brunswick. The measurements are part of an integrated study that includes geological and geophysical data acquired on the property. In order to successfully characterize the ore body, an understanding of the relevant physical parameters and their change with vertical and lateral variations of the target lithology is necessary. The quality of the estimated 3D variation in the physical properties is supported by the presence of several boreholes that randomly span the survey region. Density was measured from cores of thirty-two boreholes across the area. Seventeen of these boreholes constitute two intersecting borehole profiles, which is ideal for locally modeling the 3D distribution of the ore deposit. High densities (>3.2g/cm3) correlate strongly with Zn-rich mineralization zones (low resistivity). Compression and shear wave velocity measurements made from representative core samples of the regional geology range from ~2.91 to ~6.41 km/s for P-waves and from ~1.41 to ~4.20 km/s for S-waves. The lower bounds of these velocity values correspond to regions with a high degree of alteration. Moreover, porosity estimates from rocks on the property suggest that porosities range from 0.35% to 11.79%. Induced polarization (IP) measurements confirm that mineralized samples show a significant chargeability and resistivity contrast with respect to the host rock. Thus, chargeability and resistivity information can be combined to adequately identify conductors associated with mineralization in electrical survey data. Information on these physical parameters and their 3D statistical distribution have serious implications on various aspects of mineral exploration that include: resource estimation, choice of geophysical data acquisition and interpretation, and information for preliminary rock stability assessment.

May 1, 2009

By I. G. Townsend, S. A. Buckley, C. I. House

"SummaryBritish Petroleum plc is developing a new gold recovery process known as coal gold agglomeration (CGA) for the recovery of gold from its ores. Liberated gold grains are recovered with high efficiency by adhering to agglomerates of coal and oil. The process is simple, can recover gold grains down to very fine sizes, avoids the large scale use of cyanide and provides the industry with an important new process option.A technical appraisal of the process has been performed on an extensive range of gold bearing materials. Ore types have been identified from which high gold recoveries can be achieved. A spreadsheet based computer program has been used to estimate the preliminary capital and operating costs of the process. Comparison with established gold production costs shows that the process costs of CGA, on the appropriate ore types, are potentially very attractive, which will enable economic treatment of lower grade ores than is currently possible using conventional cyanidation. Treatment of known placer deposits or gravity concentration plant tailings may be the most rapid means of demonstrating the process at a commercial scale prior to more widespread applications.1. INTRODUCTIONWestern world gold production for the 1980s has shown rapid growth sustained by a demand for gold at a favourable price (Fig. 1). Heap leaching and CIP/CIL operations have been responsible for the major part of new production during the 1970s and 1980s with present overall production costs averaging US$200/oz in Canada, USA and Australia and US$265/oz in South Africa [l]. A great deal of research and process development effort in the 1980s has been towards the treatment of refractory ores. Operating costs for the economic processing of these ore types by currently available routes are around US$300/oz [2]."

Jan 1, 1989

By Q. Han

A modified cast-on method has been developed to reinforce aluminum castings with steel insert. Defect-free bond between the steel insert and the aluminum casting has been consistently obtained. Data obtained from a push-out experiment indicated that the bond strength was much higher than that obtained using the Al-Fin approach. This paper introduces this modified method in four sections: the coating of the steel pins, the cast-in method, microstructure characterization, and the bond strength. The section on the coating of the steel pins contains coating material selection, electro-plating technique for plating Cu and Ni on steel, and diffusion bonding of the coatings to the steel. The section on cast-in method deals with factors that affecting the quality of the metallurgical bond between the coated steel and the aluminum castings. The results of microstructure characteristics of the bonding are presented in the microstructure characterization section. A push-out experiment and the results obtained using this method is described in the section of bond strength/mechanical property.

Jan 1, 2015

By Stephen L. Chryssoulis

"""Preg-robbing"" of gold by carbonaceous matter during the cyanidation of certain types of carbonaceous gold ores is well documented. Recent studies established that ""preg-robbing"" of gold is not limited to carbonaceous matter. Gold sorbed on the surface of pyrite grains was detected and quantified by TOF-LIMS (Time of Flight Laser Ionization Mass Spectrometry). Crystallites of pyrite from a number of ores from different geological environments have been shown to have gold on their surface apparently sorbed from the ore forming solutions. Surface gold accounts for significant fractions of the gold head assay. Preg-robbing of gold by pyrite from pregnant cyanide solutions was also documented, and accounts for significant losses to tailings. Preventative measures are discussed.1.0 IntroductionThe detection and subsequent quantification of gold sorbed on the surface of pyrite particulates came about during routine determinations of the deportment of gold employing the comprehensive mineralogical approach (Chryssoulis and Cabri, 1990). In some pyritic gold ores it was discovered that the sum of the various forms in which gold ""conventionally"" occurs, was short of the gold assay. The mineralogical procedure used involves the independent determination of each fraction of gold, in other words there is no form of gold which is calculated ""by difference"". The systematic shortfall after having added the forms of gold listed in Table 1 led to the inquiry for the 'missing' gold and its discovery on the surface of pyrite grains, such as crystal facets and fractured surfaces.Preg-robbing of gold by pyrite from pregnant solutions was first described by Lloyd. In his studies, preg-robbing was measured by changes in the solutions/solids gold assays. This paper describes the first application of a direct measurement method for surface gold on pyrite particles from untreated and processed samples, its impact on gold deportment and processing. The advantage of the direct measurement lies in the absence of interference from other forms of gold, leading to more accurate and precise determinations of this unconventional form of gold."

Jan 1, 1997

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

By Sylvain Létourneau

Help organizations maximize the benefits of the data that they collect ? perform scientific research in: machine learning, data mining, statistics, artificial intelligence, soft computing, information retrieval, information systems, and natural language processing ? preferred application areas: Equipment Health Management, Bioinformatics, Health, Web Mining ? today?s talk limited to Equipment Health Management While the aircraft is still in the air, IDS: ? clusters relevant WRN, FLR, and snag (pilot) messages ? identifies probable causes based on TSM and provide links to corresponding TSM pages ? assesses MEL conditions (GO, NOGO, GOIF, ?) ? displays relevant maintenance history, suggests fixes based on similar cases ? Commercialization with MxI Technologies Ltd and Air Canada in 2000

May 1, 2008

By Michel Ruel

"PID loops – also known as base layers or regulatory controls – form the foundation of any plant’s control layer and it is generally accepted that PID loop health has a direct impact on the plant’s bottom line. Keeping these thousands of control loops in good health has a direct impact on the plant’s bottom line: it reduces variability, improves quality and throughput, and decreases energy costs and raw material usage. This has been well proven and documented in many articles. In the last ten years, technology has evolved: control engineers can now keep track of control loop performance and link it to the root causes of variability. However, they lack industry-wide best practices and criteria for determining what can be considered as excellent, good, fair, or poor performance. To ensure that PID control loops continue to perform well and meet their objectives, control engineers need a combination of (a) an appropriate monitoring technology and (b) best practices for doing the maintenance of base layer controls.Most plants have limited resources and operate with an increasing number of constraints; therefore, using the right tools and including reports in daily workflow is key for success. This paper suggests roles and responsibilities of key players needed to work toward control performance best practices and discuss organisational changes to succeed.INTRODUCTIONAlthough PID controllers are reliable workhorses in the process industry, they are often underrated. Since the 1980’s, computer control has evolved and the control algorithms used by control engineers have become increasingly complex. However, PID controllers still handle over 90% of the control loops in operating plants. Table 1 shows the savings that can be realized by achieving best-practice in several different process control categories (Brisk, 2004). The savings are expressed as a percentage of production costs."

Jan 1, 2011

By K. V. Konigsmann

"The results of Mr. Klymowsky's research confirm the essential role played by oxidation products in the flotation of base metal sulphides. They invite a discussion on the subject of aeration which I may open by a brief description of the development and current practice of aeration. The first installation of pre-flotation aeration in Canadian milling practice was undertaken during the years 1928 and 29 at the then new Noranda Mill. C.G. McLachlan and his collaborators demonstrated that the flotation differential between chalcopyrite and iron sulphides was enhanced by aeration in soda ash alkaline pulps. The ores treated contained more than 80 per cent sulphides. It was proposed already then that the products of mineral oxidation assisted copper and retarded iron sulphides, at least pyrrhotite flotation. The concentration of thiosulphates was used as a measure of the progress of oxidation. Several papers by C.G. McLachlan elaborate on this subject.The aerator was also used as classifier since it was held that aeration, i.e. controlled oxidation, should go hand in hand with creation of new mineral surfaces. Grinding mills and aerators were placed in closed circuit. Figure 1. This aeration was essential for successful separation at Noranda.Following the application of aeration at Noranda the technique was applied to existing mills in N.W. Quebec. Impressive improvements in concentrate grades and recoveries were obtained. It was observedthat the zinc flotation benefitted from aeration as much as the preceding copper float. In the late forties and fifties the aerator classifier was installed in new mills associated with the Noranda group. A diagrammatic sketch of the Quemont flow-sheet (figure 2) may serve as a typical example."

Jan 1, 1973