Search Documents

Draft tube circulators are now widely used instead of Pachucas for suspension of slurries in large tall tanks.Precipitators in the alumina industry are an example.Draft tube/tank diameter ratio is critical. Two independent criteria are given for optimum ratio. The hydraulic and energy relationships are defined. These require an impeller of very high specific speed. For a stable and efficient system the impeller should have aerofoil blades with a pitch angle which decreases from hub to tip.The draft tube must be matched to the impeller with inlet baffles above the impeller and flow control vanes below it. Tip recirculation must be suppressed. The tank itself should have a filleted flat bottom.Such a system exhibits the behaviour of axial flow devices with the characteristic undesirable behaviour at low flow.Installed and operating power requirements depend critically on hydraulic design and to a lesser extent on speed reducer efficiency.The problems of re-suspension have been overcome by a patented slot system which also improves behaviour at low flow to permit a more economic design. A number of other practical operating considerations are also discussed.

Jan 1, 1982

Of late there have been various papers published on this subject by various authorities, in which certain definite factors influencing slime settlement have been brought forward. As the principles set forth by these writers are of great interest, and have, in most cases, been generally accepted, the author will review them in the hope that by discussion some more knowledge may be brought to bear on many points connected with the subject.The definition of slime at the present time is not a standard one, and varies according to different authorities, some defining slime as ore crushed to such a fineness that it will pass through a screen of standard size, say 150 or 200-mesh, in water (1, 2);others as that part of the finely-crushed material which is in the physical condition which causes it to remain in. suspension in water, and possesses pr?perties which render it almost unleachable (3). Authorities seem divided on this point, but of late American writers seem to prefer the former definition. On the contrary, B L Gardiner describes slime as a mixture of small particles of crushed ore of varying sizes which, when mixed with water, tend...

Jan 1, 1912

At Appin colliery, geological structural analyses and investigations of roof conditions suggest roof failure may be attributed to vectorial stresses acting on underground openings, and inducing movement along inherent discontinuities in the surrounding rocks. Certain complex joint and fracture patterns tend to exhibit the effect of this movement resulting often in local deterioration in natural support.The following conclusions are drawn.1. Roof failure is related to the inherent nature of the roof rocks, the presence of mechanical discontinuities, and the vectorial stresses imposed upon it.2. Roof failure is not necessarily related to the statistically most prominent jointing.3. Colliery development approximately parallel to the direction of the statistically most prominent jointing sometimes results in favourable roof conditions.4. The maximum principal stress is the resultant of those vectorial stresses acting upon a mine opening and may be inferred from roof adjustments to those stresses after mining.5. Statistical analyses of jointing in the mine workings can provide clues to the tectonic force or forces which have been regionally or locally influential.6. There is a probable relationship between mining induced fracturing, jointing, and micro-fractures in quartz grains, within the sediments of the mine roof.

Jan 1, 1970

By Edwards A. B

Renison Bell is on the Emu Bay Railway, midway between Zeehan and Rosebery on the west coast of Tasmania. The tin deposits in this area have been described by G. A. WaIler (1902), L. K. Ward (1909), H. Hermani (1914), and Hartwell Conder (1918), for the Tasmanian Geological Survey. The ore-bodies occur in the slates, grits, altered lava flows and tufts of the Dundas Series, and consist of fine-grained cassiterite disseminated through massive sulphides (chiefly pyrrhotite or pyrite), or through bodies of quartz and sulphides. Some of these bodies show a N.W.-S.E. strike, parallel to the strike of the tin belt, but others strike N.E.-S;W. or E.-W.The ore-bodies are of two types: (1) steeply dipping fissure veins,' spoken of locally as "feeders," and (2) flatter-lying bodies more or less conformable with the bedding planes of the slates (bedded veins), spoken of locally as "floors."The feeders range from 5-12 ft. in width, with occasional bulges as great as 4q ft. Their lengths vary from 100 ft. to several hundred yards, and they are known to continue to Clmsiderable depths. 'They dip steeply, generally at angles of 45° to 60° to the east or south.The floors, where they occur, 'are directly connected with the feeders, and are sheet-iike bodies of sulphide ore. The composite ore-bodies thus have the shape of an inverted L, or a T, according to whether 'the floor extends out from one side or both sides of the feeder. Most of the floors extend from the hanging-wall side of the feeder. Where erosion has removed the connection, they appear as separate bodies.The feeders as a rule carry more quartz and arsenopyrite than the floors, and are richer in tin. In addition, the cassiterite tends to be coarser grained in the feeders than in the floors. The floors, on the other hand, carry a greater proportion of -sulphides, chiefly pyrrhotite, and the grade of ore and grain size of the cas,siterite tend to decrease as the floor is followed down the dip away from the feeder, so that the outer and lower extremities of the floors may be too low-grade to work economically. The average grade of the ore worked at present is 0·9,0/0 tin. The slates forming the roofs of the floors are commonly much contorted and silicified,' so that they form hard rocks in which the contortion and shattering of the original slates are well preserved. Joints extending upwards, more or less at right angles to the roof of the floor, are occasionally filled with finely crystalline quartz, similar to that in the orebodies, and are often rich in tin, so much so that the slate as a whole may average 0·4% tin.Some carbonate gangue is present in all of the ore-bodies, commonly on the footwall side, and, in places it becomes an important constituent...

Jan 1, 1943

In 1801, Hatchett discovered the oxide of a new element while he was examining a heavy black mineral from Haddam, America, which had been presented to the British Museum. He named the mineral Columbite and the metal Columbium. A year later a Swedish investigator, Eckeberg, while working with a new mineral resembling columbite-yttrotantalite discovered a new element, to which he gave the name of tantalum.In 1844, Rose announced the existence of two new elements in a sample of columbite from Bodenmais. One was similar to Eckeberg's tantalum and the other was called Niobium. Wollaston, in 1909, attempted to show experimentally that columbium and the tantalum were identical, but it was soon proved that they were two separate elements. Subsequently a number of investigatiors found other "new elements" in tantalum and columbium bearing ores, but these were shown to be mixtures of the twin metals.Since Hatchett's Columbium and Rose's Niobium are identical, it is more fitting to use the name assigned to this element by the earlier investigator. However, the term niobium is still retained in Germany and England.The separation of tantalum and columbium has been one of the major problems for analytical chemists since the discovery of the two elements and it is only in recent years that tantalum of a high degree of purity has been produced. High purity columbium metal is probably still to be obtained.Until 1903 tantalum was merely a laboratory curiosity, but about this time its use in incandescent electric light bulb filaments was discovered. Eight years later it was replaced by tungsten, which was better and cheaper. For a time the electrolytic valve action of tantalum was used in the charging of storage batteries, but the chief uses of the metals' to-day are for corrosion resistant apparatus, in vacuum tubes and as carbides in the manufacture of hard cutting and shaping tools.Most of the recent work on the metals has been done by C. W. Balke, in America. Tantalum has been studied more than columbium. OCCURRENCE OF TANTALUM AND COLUMBIUMI. NATURE OF ORESTantalum and columbium occur, nearly always together, as the oxides in combination with other metallic oxides. The only known exception to this is the reported occurrence of metallic tantalum with gold in the Ural Mountains. Unlike most other metals, no compounds with sulphur are known to occur in nature. Tantalum and columbium minerals occur usually...

Jan 1, 1943

The leaching characteristics of a number of Australian uranium ores were determined under acid and alkaline conditions. Ores from the Ranger, Nabarlek and Koongarra deposits in the Northern Territory were readily leached in dilute sulphuric acid. Suitable processing conditions were: leaching at 35-40°C, pH 1·52·0 and redox potential -475 mV for periods of 16-24h with ore ground to 50 per cent -200 mesh CB.S.S.). Ore from the Roxby Downs deposit in South Australia required leaching at 55°C and a redox potential of -650 mV to achieve a satisfactory recovery. All ores contained refractory minerals which were not leached under conventional conditions, limiting uranium extraction to 86-96 per cent.Carbonate leaching of carnotite in calcrete ores from Yeelirrie and Lake Way in Western Australia yielded uranium extractions of at least 98 per cent. Leaching rates were considerably faster than those reported for other applications of alkaline leaching as the slow oxidation step was not required.

Jan 1, 1979

The Research on Refined Gold Bullions Surface Upgrading

Sep 13, 2010

By M Carter

The Great South Basin is located beneath the northwest part of the Campbell Plateau, a+broad, nearly level, triangular shaped submarine platform, southeast of the South Island of New Zealand. It encompasses an area of 77 700 square kilometres and contains a sequence of Cretaceous to Tertiary sedimentary rocks which are up to 6000 metres thick near the centre of the basin (Shirley, 1983). The western boundary of the basin is adjacent to the steep Aucklands Slope. In the+ north it merges with the Canterbury Basin and to the south onlaps against the Pukaki Rise, a basement high. The eastern margin of the basin is bounded by the northeast - southwest trending steep linear Antipodes Scarp. In the extreme south the Antipodes Scarp curves westward and joins the north trending Aucklands Slope. The Campbell Plateau is dominated by tensional tectonics. The Antipodes Scarp represents a major region of transcurrent faulting initiated by Cretaceous rotation within the Campbell Plateau. Later movements are associated with the Alpine Fault of the South Island (Sandford, 1980; Anderton, Holloway, Engstrom, Ahmad and Chong, 1982).

Jan 1, 1983

By J Loimi, P Minkkinen, T Korpela

The head loss caused by metallurgical sampling for slurry streams can be reduced by metallurgical sampler design. When the process volumetric flow rate is reduced by vertical static cutters before the sampling by an equal number of moving cutters to the static cutters, the installation requires less installation head space than other sampling arrangements and is easy to accommodate at suitable locations in the process. Low head loss reduces building costs for the processing plant and operational costs during the lifetime of the plant.The presence of a possible systematic bias in the particle size distribution, solids density and elemental composition between an Outotec MSA 2/50 metallurgical slurry sampler sample and MSA 2/50 manually sampled reject have been studied by a customer. The paired samples were taken as simultaneously as possible. The customer evaluated the possible bias using a paired t-test and provided the assay results to Outotec for further evaluation.The results of the paired t-test showed no systematic bias in particle size distribution, solid density or assayed analytes, except in one analyte with low content and a high relative error. The high relative error in one analyte may have been caused by the same calibration model used in a X-ray fluorescence analyser for both high elemental-content concentrate and very low elemental-content tailings samples. The sampled stream is the tailings of a previous process stage.The results of the t-test were studied further using analysis of variance to reveal the error sources in samples. The results showed no bias between the samples collected from the MSA 2/50 reject and composite samples collected of the MSA 2/50 sample stream. The courier online analyser data was also available for evaluation of representativeness to the process stream.The analysis results of the courier online analysis reveals no bias between the MSA 2/50 reject samples, MSA 2/50 sample stream composite samples and online analysis results during the comparative sample collection period.CITATION:Loimi, J, Minkkinen, P and Korpela, T, 2017. Comparative evaluation of manual sampling and Outotec MSA 2/50 metallurgical slurry sampler, in Proceedings Eighth World Conference on Sampling and Blending , pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Madsen I. C, Langberg D. E

Recent advances in X-ray diffraction (XRD) technology have made it possible to conduct powder XRD measurements on samples at high temperatures during reaction. State-of-the-art detectors are now capable of rapidly acquiring diffraction patterns across a wide angular range (typically 120"20) enabling phase transformation rates to be measured directly during sample reaction. In this study, the phase transformations during the reduction of hematite to metallic iron by five per cent hydro ºen in nitrogen gas mixtures, were measured in situ between 500 - 700 C. Complete X-ray diffraction patterns were acquired within 15 seconds every one minute, enabling direct measurement of the transient phase abundances during the reaction. The data were quantitatively analysed by the Rietveld method to yield the abundances of hematite, magnetite, wustite and metallic iron, as functions of time during the reduction process. A first-order reactions-in-series model was proposed, and the reaction rate constants and activation energy were determined from the time-dependent phase abundance data.

Jan 1, 1999

By Woodcock J. T

When an aqueous suspension of pyrite and a manganese ore reacts with oxygen, manganese is dissolved by the ferrous sulphate and sulphuric acid produced in situ by oxidation of pyrite. In the absence of added acid, the optimum conditions are: a molecularratio of Mn02/FeS2 of about 1·0, a temperature of about 1400 C., and an oxygen pressure between 25 and 90 lb./sq. in. Under these conditions, complete extraction of manganese is obtained in six hours leaching. An addition of sulphuric acid enables an Mn02/FeS2 ratio of 2·0 to be used successfully.Manganous sulphate decreases in solubility with increase in temperature above 1000 C., but even when the solubility limit is reached during leaching, reaction to form MnS04 still proceeds, and on cooling the MnS04 redissolves.INTRODUCTIONMany manganese deposits contain secondary manganese oxide minerals which are difficult to concentrate. Considerable attention has therefore been given to their hydrometallurgical treatment. In most manganese oxide minerals, the manganese is quadrivalent and must be reduced to the divalent state for dissolution. Reduction and dissolution can be accomplished in a number of ways, one method being to use aqueous ferrous sulphate solutions.A possible source of ferrous sulphate is pyrite as it is known that ferrous ion is an intermediate product in the aqueous oxidation of pyrite. It was therefore thought possible, that by heating an aqueous suspension of manganese oxide and pyrite with oxygen, the ferrous sulphate and sulphuric acid formed from pyrite would provide the necessary leaching reagents for manganese in situ. There are certain advantages in producing ferrous ion in situ...

Jan 1, 1958

By P Rowe

New Zealand Steel's Taharoa titano-magnetite mine, south of Auckland, set two national load records when it transported around 2000 t of mining equipment three kilometres overland on time, under budget and without safety incident. It was the first time in New Zealand that four platform trailers were assembled end-to-end to transport a load. It was also the first time that a single load of 1000 t was transported on platform trailers. The need for the relocation of all equipment was realized five years ago. It took two years of planning and specialist advice to relocate the mine's 250 t dredge, 500 t surge bin, 1000 t concentrator plant and ancillary equipment from the Southern Mining Region across a specially designed haul road to the Central Mining Region. The project was carried out during a six-week shutdown in early 2001. Two dry docks were constructed, one at each end of the relocation route. The equipment was floated into a dismantling pond that was interconnected with the dry dock in the Southern Region. Through pumping, the water levels were controlled to allow transfer of the separated units from the dismantling pond into the dry dock. Once drained, sets of self-elevating platform trailers were used to transport the main units, one at a time, between the dry docks. Five prime movers were used to pull the loads. At the receiving end, the units were off-loaded in a dry dock interlinked with ,the first mining pond. The equipment was relocated because the reserves in the Southern Mining Region were mined out. A natural watercourse û the Wainui Stream û defines the northern boundary of the Southern Region and the objective became to relocate the mining plant to the other side of the stream and re-establish in the Central Region. The project team selected the trailers as the most effective means of transporting the equipment, particularly given the non-invasive means of crossing the Wainui Stream. Negotiations with prime contractor Tranzcarr Heavy Haulage Ltd commenced in mid-2000. The remainder of 2000 was spent in developing concepts with the contractor, detailed designing, preparing the dry docks, haul road and initial mine plan for the Central Region. These activities occurred with no conflict to the normal site production.

Jan 1, 2001

Fine coal is defined as material with a maximum size of 1/2 in. Various methods for separate washing of such coal are discussed briefly because separate treatment can lead to a higher overall recovery of coal or to a product having a lower ash content.A felspar jig is discussed in detail because it is the method most recently adopted in Australia, and because it has the advantages of compactness, flexibility and automatic Gontrol, with minimum operator attention. This jig has a variety of adjustable controls to enable the desired results to be obtained from a wide range of coals and the general application of each control is discussed.The only separate treatment of fine coal in the Illawarra district is by felspar jigs on Bulli seam coal.INTRODUCTIONAll reasonably large Australian collieries now win coal by mechanical methods. but while mechanization leads to more economic production of high tonnages, it also changes the characteristics of the coal won. In particular there is an increased proportion of fines, and an increased ash and moisture content. However, specifications of coal for sale have become more stringent, and consumers now require coals in a definite size range with a lower and more uniform ash content, as well as with a low and uniform moisturecontent.These factors have led to the need to wash and grade run-of-mine coal at the pithead. In' plants where the whole of the run-of-mine coal is treated in a jig, some of the fine coal in the feed is beneficiated; the extent depending on factors such as the type of coal and the feed rate. However, for dense medium treatment, fine coal must first be screened out, and there may then be no washing of fine coal at all.

Jan 1, 1961

Beneficiation of Nickel Lateritic Ore from Montes Claros de Goißs, Brazil Beneficiation is a key factor for both technical and economical aspects of industrial processing of nickel lateritic ores. A combination of comminution, classification and concentration stages are usually used to upgrade the metallurgical plant feed, thus resulting in both capital and operating cost reductions. This paper describes the testwork conducted on Montes Claros nickel lateritic ore in order to investigate the potential for upgrading. A comprehensive laboratory testing program included crushing, scrubbing, screening, grinding, gravity separation and attritioning, for both saprolitic and limonitic ore types from the Montes Claros deposit. The results indicated a clear potential for such an upgrade, which was later validated in a pilot plant program.

Sep 13, 2010

The preeipitation of dissolved lead from a strong brine by metallic iron is a chemically controlled, first order reaction. The precipitation rate is sensitive to changes in chloride concentration and temperature. The precipitation of dissolved silver is a diffusion controlled, first order reaction. The precipitation rate is insensitive to changes in chloride concentration and temperature.INTRODUCTIONLead and silver sulphates can be extracted from electrolytic zinc plant tailings, or residues, by leaching with strong brine solutions, the lead and silver going into solution as complex chlorides. One of the methods which can then be used to recover the dissolved lead and silver is to precipitate them with metallic iron. The deposition reactions which take place are of the type Pb++ Fe - Fe++ Pb............ (a)To fit such a method of precipitation successfully into a practical flowsheet it is necessary to have some knowledge of the kinetics of the various reactions, Le. to know how the precipitation rates vary with temperature, brine and metal concentrations, and so on. Reaction rates are also needed to design suitable precipitation vessels. However, when examining the possibility of using a brine leaching process to extract the lead and silver from the residue produced at the Risdon plant of the Electrolytic Zinc Co. of Australasia, it was found that, although the use of metallic iron to recover lead and silver from the pregnant brine had been reported by Ralston (1924) and by TrumbulI, Hardiek and Lawford (1948), very little was known about the precipitation reactions. Consequently a laboratory investigation was undertaken, and this paper covers those aspects considered to be...

Jan 1, 1961

By M Bird, B Oats, M Sganzerla

Mining operations are continually aiming to reduce operating costs to improve plant profitability. One way in which the Cannington operation sought to achieve this was by increasing the wear life and reducing the energy consumption of their flotation mechanisms. This was made possible using Outotec’s FloatForce mechanism. The FloatForce mechanism has been developed by Outotec over a six year period involving both CFD modelling and rigorous site testing. FloatForce delivers improved air dispersion and cell agitation efficiency; as such it can be operated at lower rotor tip speeds when compared to Outotec’s previous mechanism.Cannington trialled three FloatForce mechanisms in a train of ten OK38 zinc roughers. The mechanisms’ rotational speed was reduced by 10% compared to the previously installed MultiMix mechanisms. The purpose of the trial was to quantify the energy saving and assess whether there was any reduction in plant metallurgical performance.The trial was successful with FloatForce delivering a 17% reduction in power, an improvement in wear and improved recovery. Analysis of pre and post-installation metallurgical accounting data showed the following:The FloatForce installation resulted in a recovery increase of zinc to zinc final concentrate of 0.4 – 4.0%*The FloatForce installation resulted in a recovery increase of lead to zinc final concentrate of 0.0 – 0.3%*There was no statistically significant change in silver recovery to zinc final concentrate that can be attributed to FloatForce**95% confidence interval (CI) using multiple linear regression models.The Cannington operation is now in the process of further optimizing its power consumption and wear savings by changing the remaining OK38 zinc and lead rougher float cells to FloatForce mechanisms.CITATION:Bird, M, Oats, B and Sganzerla, M, 2015. Improvements in flotation cell maintenance, power consumption and operation at South32 Cannington, in Proceedings MetPlant 2015, pp 230–245 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Australia has a long history of underground mining. Even withadvances in open cut mining equipment, techniques andeconomics, many orebodies are still best mined by undergroundmeans. In addition, modern exploration tools are æuncoveringÆorebodies that are at increasing depths. South African mines arecurrently producing from below 3 km, and developing down to5 km depths û it is likely that Australian mines will also becomemuch deeper over the next 20 years. One of the most significanttechnical challenges in deep mines is the problem of heat.Community expectations and legislated standards continue todrive operations towards improving the working conditions inmines. The hazards and costs associated with chronic hotworking conditions (heat illness, poor safety, poor productivity,higher operating costs and poor morale) are also becomingincreasingly recognised (Brake, Donoghue and Bates, 1998). Theexposure of miners to many other occupational hazards has beenreduced over the past 50 years. However, despite air-conditionedcabins greatly reducing the heat stress on mobile plant operators,there are still many Australian mine workers subject to levels ofthermal stress that existed a century ago. There are severalreasons for this, including a frequently-poor understanding of thephysiology of working in heat by mine management, no agreedmining code of practice for working in heat, the lack of a robust,practical-sized instrument to measure heat stress, the costpressures on the industry and, to some extent, deep-seatedtraditional management and worker practices. Howeversignificant progress has been made in many of these areas (Brakeand Bates, in press), with the net result that there is likely to be a trend towards installation of refrigeration of some form in manyAustralian mines in the future. This will add directly to the costof operation, but will also have direct and indirect benefits,including cost benefits. It should also be noted that Australia isnot at the forefront of adopting practices to manage temperaturesin the workplace: South African metal mines usually haverefrigerated cooling, and Canadian mines spend large sums onheating, with heating costs (averaged over a full year) of up to$A1 per tonne mined (Bandopadhyay et al, 1997). The history of mine refrigeration dates back to 1919 when thefirst plant was installed at Morro Velho, Brazil. By 1965, the totalinstalled capacity (worldwide) reached about 100 MW(R)i. Since 1965 the growth in mine refrigeration capacity has beenexponential, with a doubling every six or seven years (Howes andNixon, 1997). South Africa is by far the largest user of minerefrigeration, with over 300 refrigeration machines installed. This paper discusses the key design issues associated with theapplication of refrigeration in underground metal or coal mines.Whilst the emphasis is on large, surface plants, small, surface orunderground refrigeration plants can also be very effective in thecorrect application and many of the principles of design andoperation are the same.

Jan 1, 2001

Reconnaissance geochemical exploration in the vicinity of low angle detachment faults which bound the core of the Paparoa metamorphic core complex yielded Au up to 14 ppm, with 35% of greywacke, granitoid and quartz vein samples in the northern range exceeding the 0.01 ppm detection limit. Au is associated with Ag, As, Sb and Cu anomalies consistent with epithermal-type mineralisation. The Ag and Cu anomalies also distinguish this mineralisation from older, mesothermal Au deposits widespread in the Ordovician 'slate belt' greywackes, which comprise much of the upper plate of the core complex. Baryte, molybdenite, fluorite and stratiform U mineralisation in the northernPaparoa Range may also be related to hydrothermal activity along the detachment fault zones.

Jan 1, 1995

This paper summarizes the progress of geological exploration at North Broken Hill Ltd.The North Mine orebodies occur in knots of minor folds on a simple limb structure which is itself highly folded, giving rise to two distinct orebodies pitching N. at av. 42° down to 2,920-ft. level, where the pitch steepens to near vertical as a result of complementary shear movement on the Globe-Vauxhall Crush Zone.The lack of adequate marker beds and top and bottom relations makes the resolving of the complex structural environment of the orebodies most difficult.To test the deeper ground of each side of the De Bavay Fault on the 2,600-ft. level the footwall drive was extended 3,556 feet and over 20,000 ft. of drilling completed from three transverse fans, only one of which intersected the orebodies due to steepening of pitch.The problem of locating the North Mine orebodies N. of the DeBavay Fault remains speculative because the exact position of them S. of the fault is still unknown. Exploration beyond the fault in the search for ore had two lines of mineralization to consider, an eastern one through Cosgroves-Round Hill, long regarded as the continuation of the main lode, and a western one passing through Silver Hill Silver Peak.From surface 45,000 ft. of drilling was completed in five sections, establishing that the structure was dominantly synclinal with a flatdipping E. limb, the W. limb and adjoining structures being involved in the Globe-Vauxhall Crush Zone. Mineralization, though weak, was remarkably persistent but the economic mineralization exposed at surface has not persisted with any continuity.Deep exploratory drilling below the bottom level (3,370 ft.) has established high-grade ore to a depth of 4,095 ft. and also has proved its existence within the Globe-Vauxhall Crush Zone.INTRODUCTIONThis paper summarizes the progress of geological exploration at North Broken Hill Limited from the inception of the Geological Department in 1941 until the end of 1955. The writer has drawn freely on departmental records for the period prior to 1947.

Jan 1, 1956

WHILE in the employ of the Broken Hill Associated Smelters and the Electrolytic Zinc Oompanies at their South Melbourne Research Station, the writer was detailed to investigate the principles underlying the Parkes Process with a view of determining:1. The Interdependence of the variables:(a) Quantity of zinc required per charge,(b) Temperature of stirring of each zincing,(c) Silver content of the bullion after first zinculg,(d) Silver content of the bullion after second zincing,(e) Silver grade of the crusts produced for retorting, with reference to the method of working the Parkes Process then in operation at Port Pirie.2. The possibility of effecting improvements in the Port Pirie practice of desilverising, especially with respect to:(a) Silver grade of the crusts produced for retorting.(b) Quantity of zinc required per charge.The method of desilverising in practice at Port Pirie was a two-stage zincing.In both zincings the bullion was cooled to its solidification temperature and the silver crusts which separated from the lead were completely removed.The crusts from the first zincing were retorted, and the crusts from the second zincing were returned to the first zincing of the next charge.

Jan 1, 1925