Search Documents

A narrow (200-300m) zone of amphibolite facies metamorphic rocks underlies the Papuan ophiolite near the Musa-Kumusi divide, SW of Popondetta, Oro Province. The amphibolite rocks are bounded up-section, to the NE, by peridotite and gabbro of the ophiolite; and down-section, to the SW, by mafic greenschist, which in turn overlies blueschist facies mafic schists of the Emo Metamorphics.Amphibole compositions within the narrow contact zone show a strong chemical zonation which reflects a steep thermal gradient, with maximum temperatures >800¦C at the peridotite contact. The zonation is recorded in Ti content and A-site occupancy, relative to Al'¦

Jan 1, 1994

The Quioma Mine is located along the axis of the Cordillera Oriental, 130 km southeast of Cochabamba, South Central Bolivia. Silver, lead, zinc, antimony, and gold have been intermittently produced from veins in the Quioma area since Colonial times. Mineralization occurs within steeply dipping fissure veins transecting moderately folded Lower Ordovician sediments. Tectonic activity is early to mid-Tertiary and the vein system parallels the fold axis of a major northwest-southeast striking, doubly plunging anticline. Vein sets occur within a 2 km wide band over a strike distance of 13 km along the northeast limb of the anticline. Economic mineralization occupies syntectonic pre-mineral fault zones developed in more competent stratigraphis units of Lower Ordovician clastic sediments. Veins average 55 cm in width, although mineralized structures up to 3 m wide with a known strike length of several hundred meters have been mined. Mineralization consists of siderite, argentifferous galena, sphalerite, and quartz, with minor amounts of chalcopyrite, barite, and bournonite. Pyrite is rare except at the Boston vein where it occurs with stibnite that contains trace amounts of gold. A marked characteristic of veins in the district is evidence of repeated stages of movement during mineralization. Intrusive rocks are rare in the Quioma area. Narrow porphyritic dikes of Andesitic composition averaging 1 m in thickness have been observed. These dikes occasionally show a close spatial relationship to the veins and are often kaolinized and carbonitized. Vein and dike contacts are sharp and alteration does not appear to extend into the wall rock. Mineral zoning is suggested by antimony mineralization observed in peripheral areas of the anticline.

Jan 1, 1987

The Prince Lyell Mine has been the major production source at Mount Lyell since under-ground mining commenced in 1972.Three lifts of stopes have been mined to date, with the fourth, the 40 Series lift, to commence production this year. As the mine has progressed deeper, the ore haulage system has evolved to accommodate the mine's economic circumstances while maximizing efficiency.In the first, or 10 Series lift of stopes, ore was removed from drawpoints by L.H.D. units and tipped directly into rakes of 7 tonne rail cars. The original concept for deeper stoping lifts entailed L.H.D.'s tipping into long ore passes, rail haulage, underground crushing and hoisting to surface via the No. 1 Shaft. The suspension of the No. 1 Shaft project in 1976, due to economic difficulties, lead to the intro-duction of diesel truck haulage of ore, initially via the internal Prince Lyell Decline and now to surface via the Main Decline.

Jan 1, 1985

By Tucker G, Clark A, Young M. F, Johnston M

Mount Isa Mines has made a huge commitment to process control in milling. Yet in lead zinc we still failed to achieve a steady operation. Comparisons with manufacturing plants showed the key difference was failure to control plant inputs. Lead

Jan 1, 1998

By Skaviniak M

Some better perspectives applying to the exploitation and dressing of polymetallic ores in the Banskfa. gtiavnica-Hod- rusea Ore District are supposed to be achieved after a suc- cessful investigation and proving there the existence of deep-seated mineralization as well as due to increasing de- mand for non-ferrous metals and consequently to higher mar- ket prices of those recently noticed. With respect to the present situation in mining and to the further technical development as well, a several times higher exploitation may be in this region expected, especially in the deeper .eated parts of the deposit. When solving the tasks of a complex economic exploitation over the whole region, consi- derable attention is paid to regional relations and impact studies (due to expected exploitation and ore dressing but also to very difficult problems of dewatering (drainage pro- blems-). It will be first of all necessary to find there an equilibrium between the consequences resulting from the re- naissance of mining industry and environmental requests un- dispensable for the city of Banska 9tiavnica and the other neighbouring towns in the vicinity of mining plants.

Jan 1, 1988

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976

This paper outlines some of the recent developments in Spiral Concentrator design, with particular reference to the range of Reichert spirals supplied by Mineral Deposits Limited, typical applications, and test or operating data, are also provided for the different series of spirals now available.

Jan 1, 1978

The control system of a mine winder or other variable speed drive has many component parts that must work together to provide the required functional performance of the machine, together with comprehensive safety features, reliability, maintainability, user-friendliness and efficiency. Modern winders use digital control technology extensively and hence software design is a major part of the overall system. It is not practical to simulate an entire mine winder in a single computer model because of the sheer mathematical complexity of the behaviour of many of the components. However, most component parts can be simulated quite easily, and related parts of the control system software can be simulated. Such simulations allow control software algorithms to be developed and tested in isolation from the real plant. Tests can be performed on the model without fear of injury to personnel or damage to the valuable plant. For example, speed regulator control algorithms and stability settings can be adjusted to and beyond the limits of stable operation, and near optimum settings can be found. This is particularly important, for example, when designing closed loop controls for emergency brake systems. Obviously, care must be taken to ensure that the computer model of the plant is realistic and takes into account as many non-linear features of the real plant as possible. Pure mathematical analysis of some systems is very difficult to perform when non-linear plant behaviour is involved. This paper shares a number of practical simulation experiences performed using commercially available software such as Matlab and Simulink to simulate various parts of the control system of a mine winder or other variable speed drive. Demonstrations of the operation of several different computer models are shown during the presentation of the paper.

Jan 1, 2005

By G Brewster

The Eagle on the Hill tunnels form part of an upgrade of Mt Barker Road, 15 km to the southeast of Adelaide. The upgrade significantly improves safety and reduces delays on this major road, which winds steeply through mountainous terrain. The twin tunnels each spanning 15 metres run in parallel for a length of 480 metres. The tunnels are excavated in slightly weathered high strength slates and very high strength quartzites of the Saddleworth Formation on the western margin of the Mount Lofty Ranges. Steeply dipping slate cleavages and the high fracture ratio result in many slope stability problems in the project area. The level of geotechnical investigation undertaken prior to the calling of tenders for the project was extensive. This included the excavation of a pilot tunnel along one of the tunnel alignments, which allowed accurate mapping and rating of the rock, resulting in an increased level of confidence during the tender process. One of the features of the winning alternative tender design was the use of canopy tubes, flexible steel ribs and shotcrete to replace up to 40 metres of deep portal cuts in unstable rock with driven tunnels. Slope stability issues were overcome with the use of rock dowels and shotcrete. The support concept allowed the safe driving of the tunnel portals with as little as two metres of overburden. The design incorporated lining drainage and criteria for fireproofing based on European experience to ensure the ability of the tunnels to remain stable in the case of a severe fire incident. The support design allowed for maximum flexibility with a range of support types able to deal with the varying ground conditions. Design development and support refinement continued throughout the tunnel construction phase with close liaison between the designer and the constructor. Monitoring and review of feedback from the construction site by the Sydney based design team was easily achieved by means of electronic transfer of photographic and survey information, telephone and fax communication and regular site visits. The contractor for this project is Macmahon Concrete Constructions Joint Venture (MCCJV) and the designer is Connell Wagner. Excavation commenced in January 1998 with tunnel breakthrough having been achieved in early-August 1998 and mid-September 1998 respectively. Concrete lining construction is scheduled for completion in April 1999.

Jan 1, 1999

By Veloso L, Alvarez O, David D

Cerro Colorado operations The Cerro Colorado Mine is located 150 km east of Iquique in the Atacama desert of northern Chile. The mine is wholly owned by Rio Algom Limited of Canada and produces copper metal using a bio leaching process. Tw

Jan 1, 1998

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

By B G. Lottermoser

Phosphate induced stabilisation has been used to create passive iron phosphate coatings on pyrite and pyrrhotite. The formation of solid phosphate coatings on sulfide grains thereby inhibits sulfide oxidation. The aims of the study were to determine whether phosphate induced stabilisation could control sulfide oxidation and metal mobility in partly oxidised, polymineralic, sulfidic mine wastes. Waste materials were obtained from the acid mine drainage generating, abandoned Montalbion silver mine site, far north Queensland, Australia. The waste consists of quartz, kaolinite/illite, sulfide minerals (galena, chalcopyrite, tetrahedrite, sphalerite, pyrite, arsenopyrite), and pre- and post-mining oxidation products (hydrated Fe, Cu, Pb and alkali mineral salts). SEM observations of waste material treated with potassium orthophosphate showed that metal, metal-alkali and alkali phosphate coatings developed on all sulfides (with the exception of tetrahedrite). The abundance of phosphate phases was dependant on the availability of cations in solution for complexation with the phosphate anion. In turn, the release of cations was dependent on sulfide oxidation or the dissolution of efflorescent mineral salts. Experiments aiming to dissolve these phosphate coatings û using a strongly oxidising solution û showed that the phosphate coatings remained stable, preventing acid generation and metal release. The results of this study demonstrate that liquid phosphate stabilisers can suppress sulfide oxidation and immobilise metals in partly oxidised, polymineralic mine wastes.

Jan 1, 2003

By S Harvey

An inrush of water or mud into an underground mine, or sudden subsidence above mining voids represent low probability but high impact risks in underground mining. About two such incidents involving multiple fatalities or loss of production are reported each year worldwide. On average, Australia experiences one such incident every three to four years. This paper reports the development of a Standard that is intended to eliminate fatalities due to inrushes and subsidence.

Jan 1, 1998

By S N SHEARD

The use of geophysics in mineral exploration in Australia, and overseas, has increased dramatically over this century. This paper shows that using simple equipment with clever interpretation that the foundations of modem geophysics were laid, using all the same principles. The plethora and diversity of mineral exploration geophysical techniques does not allow a full description of their evolution to be given in such a paper. To convey this evolution, however, the progress of two different geophysical methods, magnetics - a potential field (passive) method, and electromagnetics - an electrical (active) method, are described. Examples of magnetic survey data from the 1920s and more recent vehicle home and airborne surveys are given to show the increase in data quality through technological improvement. A set of four airborne electromagnetic data sets spanning three decades is used to indicate the improvement in electromagnetic techniques. It is argued, that considerable progress is still required in the electromagnetic field to increase its interpretability.

Jan 1, 1992

By Millett R

In January 1989, Western Mining Corporation (WMC) acquired the Perseverance and Rocky's Reward orebodies and associated infrastructure from the Agnew Mining Company (AMC). AMC had closed the operation in August 1986 and it had been on care and maintenance since that time. To return the operation to full production as quickly as possible it was planned to mine the Rocky's Reward orebody by opencut mining and treat this ore whilst the underground Perseverance workings were rehabilitated. Removal of overburden from Rocky's Reward thus commenced immediately with a target of April 1989 for delivery of the first ore to the concentrator. Extensive rehabilitation and upgrading of the concentrator commenced in late January, and continued in stages for an 18 month period. The first stage consisted of overhauling all existing equipment and completing a crusher upgrade commenced by AMC prior to the mine closure. During this period, it was necessary to recruit a workforce and re-establish all the required support structure. In late April the plant commenced commissioning trials on mullock. The first ore was crushed on the 11th May 1989 and concentrate produced the following day. From May 1989 to June 1990 the plant was producing nickel concentrate whilst further upgrading continued. During this period, the flotation capacity was tripled by installation of a bank of eight Wemco 144L flotation cells in rougher-scavenger duties and two 12 metre by 2 metre diameter columns in cleaning duties. The existing vacuum drum filters were replaced by two Larox PF32 pressure filters, eliminating the need for solar drying and allowing the flash drier to be fed direct from the filters. These, along with a major borefield expansion and further work to the crusher increased the nominal plant capacity from 600,000 to 1,000,000 t/yr. The plant achieved the 1,000,000 t/yr rate in April 1990.

Jan 1, 1991

By G A. Partington

Recent research has highlighted the potential of a relatively new style of gold mineralisation related to granite intrusion. New discoveries in Alaska, Central Europe and Asia and Eastern Australia with total resources of 1600 t Au offer attractive targets for regional exploration in areas which may have been overlooked in the past. A spatial information system was developed to target granite-gold systems in eastern Australia and the West coast of New Zealand, using well constrained geological and exploration models derived from current research. Target areas were recognised in Queensland, New South Wales, Victoria, Tasmania and on the West Coast of the South Island of New Zealand that have similar spatial data relationships to known granite gold mineralisation elsewhere in the world. The second phase of the modelling better constrained the regional scale target areas by including more detailed geological, geochemical and geophysical data in the GIS to develop prospect-scale targets and to allow the acquisition of tenements over these areas. A geological review of each target area was carried out in the field to put the GIS models into context. The fieldwork has highlighted the potential for this style of mineralisation in New Zealand and will increase investment in mineral exploration and development in New Zealand in the near future.

Jan 1, 2005

In the general planning of this area, provision was made for the distribution over the whole area as required of the following services:(a) Power and lighting from the substation distribution boards 'located in the winder house.(b) Miscellaneous electrical indicating, control and signalling systems.(c) Telephone lines from the main internal automatic exchange located in the changehouse, the town exchange to the automatic exchange and also direct lines from the town exchange to selected offices.(d) Compressed air from the incoming 16-in. air main. (e) Water, both unfiltered and filtered; and the disposal of the following effluents:(f) Sewage from the area to the town sewage system.(g) Changehouse shower water to the regeneration area.(h) Storm water to the general mine surface drainage system leading out to the naturally drained area north of the No. 8 Shaft.

Jan 1, 1957

The Mary Kathleen uranium deposit occurs in 1740-1780 M yr-old calc-silicate melasedimentary and mela-igneous rocks of lhe Corella Formalion which have been tightly folded into lhe Mary Kathleen Syncline. The Corella Formation consists of malic and felsic tuffaceous(?) calc-silicates, quartzile, and minor marble, conglomerate and basic volcanics. Garnet-rich rocks form semi-concordant and transgressive masses in the middle and upper portion of the sequence. Granite, gabbro and acid porphyry dykes also occur in the syncline.Uranium-rare earth mineralisation is closely associated with certain malic rocks and occurs wilhin or close to garnet-rich masses. At Mary Kathleen, uraninite grains are enclosed mainly by allanite which is dislribuled through massive garnet as an irregular honeycomb of interconnected shoot and lenses. The mineralisation occurs along strike from dioritic rocks and conglomerate and lies close to the axis of the Mary Kathleen yncline and adjacent to a major faull zone. All other localities allanite-uraninile mineralisation is broadly stratiform.The mineralisation is interpreted to occur at or near centres of basic volcanism. Garnet formation and uranium-rare earth concentrations are believed to be caused by the volcanism, and to be contemporaneous with it. The former is seen as alteration of a hot, saturated pile of volcano-sedimentary material and the latter as intermittent hydrothermal exhalation.Deposition, volcanism, garnet formation, uranium and rare-earth mineralisation, granile and gabbro formation, and tectonism are seen as a continuum of interrelated processes which operated throughout the period of format ion of the rocks in the Mary Kathleen Syncline.

Jan 1, 1985

By E Yll÷, O HyvSrinen

Outokumpu has developed a new chloride leach process, called HydroCopper«, to treat copper concentrates. Chalcopyrite is quite refractory in leaching and in sulfate milieu an autoclave of high temperature and pressure is required. However, in the HydroCopper«-process copper sulfides can effectively be leached in atmospheric pressure using strong, aggressive chloride solution and copper (II) ions as oxidant. Copper is precipitated from the purified pregnant leach solution as copper (I) oxide, which is filtered and reduced by hydrogen gas to metallic copper powder, which is melted and cast into copper product. Sodium chloride formed in precipitation is decomposed in a chlor-alkali electrolyser, the products of which are circulated back to the process: sodium hydroxide to copper (I) oxide precipitation, chlorine gas to leaching and hydrogen gas to the reduction of copper (I) oxide. During 2003 - 2004 the performance of the HydroCopper«-process was confirmed in a demonstration plant processing one tonne of copper per day. It has been found to be applicable for different kinds of concentrates and can also tolerate a wide range of impurities. A significant advantage of the process is that gold can be leached as a chloro-complex and recovered with active carbon. HydroCopper« can economically recover copper from concentrates and process to a cast copper product. The best utilisation of the process is in most cases achieved when the plant is situated at the mine site. Higher recoveries are attained by the optimisation of the whole operation chain from the mine and the concentrator to the HydroCopper« plant.

Jan 1, 2005

By Grobler H. P, Chitombo G. R

Production blasting of Dc Beers Consolidated Mines Limited, Koffiefontein and Finsch Mines involves both uphole trough rings of 9 to I I holes and near vertical 360 degree compound rings of 42-54 holes. The rate of production from these stages is dependent upon being able to achieve a specified fragmentation size range and this has driven the derivation of blasting practices to consistently achieve this target fragmentation. At the Dutoitspan Mine, in Kimberley, where mining of the kimberlite pipe is by block caving, 100 per cent extraction of the undercut level by ring blasting is essential. If this is not achieved, pillars are formed which not only inhibit the efficient initiation of the caving process, but also concentrates load onto the extraction level, causing damage to draw points and pillars. These two case studies demonstrate the importance of achieving optimum blasting performance for downstream mining efficiency; ie fragmentation for increased productivity at Koffiefontein Mine and 100 per cent undercut extraction for efficient initiation of the caving process at the Dutoitspan Mine. The case studies also serve to highlight the long road towards blast optimisation taken by De Beers Consolidated Mines Ltd (Koffiefontein. Finsch, Premier and Kimberley Mines) since 1989.

Jan 1, 1995