Search Documents

By F Cappuccitti

A colourimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured. The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimisation of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimise the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.

Jan 1, 2005

By White L. R, Boger D. V

The paper describes the surface chemistry and particle physics that control the fundamental flow properties (Theology) of mineral particle slurries. We further address, through a series of case studies, the design data that emerges from experimental studies of the flow properties of complex, high volume fraction mineral slurries. The case studies are drawn from mineral oxide concentrate processes, tailings dewatering operations and from filter cake production and management. The paper emphasises the essential links between design of process slurry handling systems and the control of the flow of such slurries by control of the pulp chemistry.

Jan 1, 1992

By J S. Kuszmaul, T O. Aspinall

The applicability of environmental geotechnics for erosion management is increasing in importance worldwide. The environmental impact of mining and evolving environmental legislation has been receiving increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental legislative agencies and members of the public. This is because of the need to increase the reliability of erosion prediction and in the minimisation of costs for spoil dump design. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. Engineering design of mine spoil dumps seeks to reduce the potential for such erosion damage through correct selection of an initial stable landform scheme (Goh, 1997). The design of mine spoil dumps must also conform to the specifications of evolving legislation. The Queensland Environmental Management Overview Strategy (EMOS) states that, for minimised degradation of the surface area due to erosion during the development of a project, the erosion rates should be between 12 - 40 tonnes/hectare/year and that the depths of rills and gullies be limited to less than 30 cm (QDPI, 1988). The aim of engineering design is to ensure the long-term stability of the spoil dumps. The implementation of effective planning and operating procedures through recontouring and grading assists in the reshaping of spoil dumps to a safe, stable and non-erodible environment.

Jan 1, 1998

By J R BISHOP

Geophysical techniques are being increasingly used down exploration drill holes as deeper and more elusive targets are sought. This paper lists the various methods available and discusses the applications using a number of examples.

Jan 1, 1992

By J A Evans

A well-maintained and low cost mining operation today requires the use of condition monitoring techniques. At ERA - Ranger Mine oil analysis, vibration monitoring, infra-red themtography, and performance analysis have been successfully applied over the last four years to lower operating and maintenance costs. All condition monitoring is scheduled through a comprehensive in-house developed maintenance management system known as the Engineering Information System (EIS). (EIS) is used extensively at Ranger to ensure consistent frequency and recording .of all condition monitoring data. This paper provides an insight into the benefits of condition monitoring and explores the future direction for condition monitoring techniques at Ranger.

Jan 1, 1994

By G Ferguson a, P Carrasco, P P. A Dowd

International codes of practice offer broad definitions with respect to the classification of resources in terms of risk. Specific guidelines and protocols, to analyse sample data, carry out geostatistical appraisals, develop geological models and finally estimate and classify resources, are not addressed. Neither are detailed requirements for engineering mineable reserves from estimated resources. In addition, international codes of practice fail to distinguish between types of deposit, other than in broad terms, as for example, The AusIMM JORC Code (JORC, 1999) which makes reference to diamond and coal deposits. The objective of this paper is therefore to set in motion the process of specifying detailed protocols, acceptable to the international community, for the assessment, reduction and management of risk associated with the development and extraction of mineral deposits. Ordinarily, the main risks and issues encountered during the process of estimating resources and subsequent conversion to reserves, encompass:failure to understand relevant geological controls of mineralisation; validation of grade interpolation; optimism in geotechnical appraisals of dilution and stability and the consequent selection of inappropriate mining methods; metallurgical modelling of minerals and contaminants reporting to concentrates; appraising the hydraulics of heap leaching and the numerous factors that can affect recovery; difficulty of managing metal price cycles and changes in regulations within the constraints of long-term mining plans; and development of better evaluation techniques for mining ventures. Uncertainty is inherent in estimation and engineering work, and its identification, reduction and management should be a fundamental goal of all involved in the mining industry (Figure 1). Variability may be reduced by:following internationally accepted practices for the collection, manipulation and analysis of geoscientific data; and verifying that the procedures actually performed meet the associated standards. Increasing amounts of data will also reduce uncertainty, but only if the procedures used to collect and appraise such data follow the relevant procedures. It is thus the aim of a series of papers in preparation, Beniscelli et al (in prep), to put forward detailed guidelines, for:project sponsors û to provide a global view of the work and documentation needed to support requests for funding various phases of project development and budget approvals; geologists û to indicate a checklist of the requirements and standards for the exploration and estimation of resources; and engineers and economic analysists û the protocols for characterising, modelling, engineering and evaluating the extraction of reserves. It is therefore hoped to encourage the development of consistent standards for declaring reserves within the mining industry. Data from projects and operations will be utilised to illustrate the benefits of adopting a rigorous approach to estimating resources and engineering reserves, Beniscelli et al (in prep).

Jan 1, 2000

A laboratory investigation was carried out to obtain data on the explosive character- istics of selected coals mined in New South Wales. Seven coal seams were sampled and the volatile matter content of the coals tested varied between 28 and 37 percent. A mod- ified Hartmann apparatus with a volume of 1250 ml was used in the investigation. Dust clou' generation was produced by an air blast delivered radially through a mushroom type valve and the ignition source was a-continuous A.C. spark produced by a 20 000 V, 50 mA transformer. The coal dust parameters invest- igated were the maximum pressure developed, the average and maximum rates of pressure rise at dust concentrations between 200 and 1500 3 g/m.

Jan 1, 1981

By J O. Watson, V S. Vutukuri

This paper presents results of an investigation on acoustic emission characteristics of granite, sandstone and rock-like material in the unconfined compression and tensile tests. Both the acoustic emission signature and stress-stain curve are analysed in the experiments.The experimental results show that different acoustic emission characteristics are observed at different stress and deformation stages in unconfined compression and tensile testing. Extensive and unstable acoustic emission changes may be interpreted as indicating failure of the rock.

Jan 1, 1999

By M S. Powell, M P. Bueno

The commonly used SAB, SABC and run-of-mine (ROM) ball mill circuits can achieve high throughputs with good operating stability. However, these circuits consume a substantial amount of grinding media, which can have a substantial impact on the OPEX and the æcarbon footprintÆ, specifically when viewed as an æembodiedÆ energy input. On the other hand, fully autogenous (AG) circuits can operate at much lower operating costs, but with limited throughput. The control of AG mills, fed by ores with hard and soft components, can also be challenging, due to the sensitivity of the mill to the ratio of hard to soft components.In this paper, a multi-component modelling approach was used to demonstrate that the harder component should be used as grinding media, and its use should be kept to a minimum to avoid reduction in the mill throughput. There is an optimal blend of hard to soft, and any optimal blending condition is both ore-dependent and mill-specific. Establishing this blend is challenging, and consequently discourages the use of autogenous mills. The new modelling approach addresses this challenge by providing a quantitative prediction of the influence of blending soft and hard components in a mill. This prediction can then be used to establish the required blend for maintaining a stable and efficient operation in autogenous grinding mode.CITATION:Bueno, M P and Powell, M S, 2012. How to use hard ore components as grinding media, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Hollis R. G, Tuppurainen J. M I

Improved control of non-ferrous sintering operations requires the on-line measurement of sinter quality. No on-line measure of sinter quality is currently available, however, previous work has shown that the raw mix chemistry and peak sintering temperature determine the mineral phases formed and hence the resulting Blast Furnace behaviour. Control of these factors should therefore lead to improved quality control. In this paper, the development of a simplified heat and mass balance model of the Sinter Plant at Mt Isa is described. The model used available plant data to calculate raw mix composition and a simplified reaction scheme to predict sinter composition. The extent of reaction is inferred from the flue gas analyses. Off-line testing of a dynamic version demonstrated that actual plant performance could be predicted with reasonable accuracy.

Jan 1, 1989

By P D. Williams

The Phoenix mine is one of NewmontÆs open-pit operations located in Nevada. Mining started in 2005, with the mine producing gold, copper and silver. The mine life is about 20 years. The gold grade estimation uses the Newmont in-house indicator kriging approach to handle the high variability in drill hole composite grades and support mining selectivity. Each block contains up to 200 subblocks with different gold grades. A flotation mill is designed to process oxide and sulfide ores, recovering gold, copper, and silver. An additional copper leach process is currently under study to process low gold and high copper oxide material with low copper recovery in the mill. The metallurgical recoveries and processing costs are dependent on many variables including rock formation, metallurgical domain, cyanide soluble copper and sulfide contents. This paper describes the Newmont in-house indicator kriging procedures and the revenue based mine planning software system implemented at Phoenix mine to address the complexity resulting from multi-process, multi-metal and indicator kriging model.

Jan 1, 2007

By Vassiliev P

Cut-off optimisation, based on the work of Lane (1988), can be used to maximise the NPV (Net Present Value) of a mine by the judicious manipulation of cut-offs and the use of stockpiles. Apart from maximising NPV, cut-off optimisation will ver

Jan 1, 1998

The Beaconsfield gold mine processing plant is a complex operation and utilises crushing, grinding, gravity gold concentration, sulfide flotation, bacterial oxidation, cyanidation and zinc cementation to recover gold from the partially refractory ore. This paper discusses the challenges, developments and advancements throughout the processing plant since start up, which have culminated in a 25 per cent increase in the mill throughput over the nameplate design and a concomitant gold recovery increase from 75 to 92 per cent. The improvements have been attained via advancements in mechanical integrity, metallurgical review, process control and operator training, resulting in the current operation producing over 630 000 ounces of gold to date.

Jan 1, 2007

By M P. Schwarz

This paper describes modelling studies of the flotation cells used by BHP Billiton Nickel West Ltd in the slimes circuit at Mt Keith. The aim is to achieve a better understanding of the hydrodynamic limitations in the existing cells to improve nickel recovery. Computational fluid dynamics (CFD) simulations have been performed on the 100 m3 mechanically-stirred cells. The data produced by the simulations include velocity vectors, gas holdup distribution, solids distribution, bubble size, superficial gas velocity and turbulent parameters. These results have been checked and found to match hydrodynamic measurements at the plant. An analysis of the data found that one of the limitations in fine particle recovery was related to the air bubbles discharged with the tailing. The air in the discharge was caused by the high viscosity of the pulp. In the presence of fine particles, the pulp exhibits high viscosity with a yield stress. The increased drag due to high viscosity caused the bubbles to rise more slowly up the cell. This results in a significant hold-up of bubbles, some of which report to the tailing with associated loss of valuable minerals. A parametric CFD study of the operating variables shows that less air would be discharged in the tailing by decreasing the following: air flow rate,pulp density,stirring speed, andfrother addition. Simulation results indicate that these changes would cause a lowering of the air hold up in the cell especially near the discharge area. Predictions of the bubble-particle attachment rates under various operating conditions have also been calculated. Although it is possible to increase attachment rates by increasing stirring speed or by increasing pulp density, the amount of air discharged and the amount of nickel loss through the tailing will also increase. The project showed that CFD modelling is a powerful tool for studying hydrodynamic effects of bubble-particle interactions in flotation cells.

Jan 1, 2008

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

By S Youds

The backfilling operation at Olympic Dam mine supports a 9.8 Mtpa underground Long Hole Open Stoping (LHOS) operation. It involves a combination of Cemented Aggregate Fill (CAF), surface rockfill and underground rockfill. The fill material is introduced from the surface via boreholes into the top of the stopes. Due to the deleterious effects of the dust and the thickness of the atmosphere in the stope it is not possible to view the filling process either at optical or infrared (IR) wavelengths. The need for a means to measure the filling process is driven by the placement of both rock and CAF fill in the stopes. The large volumes and high relative cost of CAF makes the minimisation of CAF fill a business priority. Incorrect filling can lead to the sterilisation of ore reserve. The use of millimeter wave radar to view through the haze to give real-time data on the relative positions of the different fill masses is being developed as an in-stope fill monitoring device. This paper reviews the salient points of the technology and its potential use in the backfilling operation at Olympic Dam. The broader potential of this technology for use in the mining industry by æseeingÆ through water and dust laden environments such as that found in stopes and ore passes is also discussed.

Jan 1, 2002

By Purvis A. H, Greenwood-Smith R, Sowerby B. D

A nuclear technique for the determination of copper and nickel in bulk samples and drill core has been developed at Lucas Heights andfield-tested at Mount Isa. The technique, which is highly specific to the element being measured, utilises the gamma-ray resonance scallering process.A bulk mineral analyser was installed in mid-1976 for the routine assay of copper in bulk samples and drill cores, and remained in operation until late 1981. The operation of the analyser over this five-year period is reviewed with particular emphasis on reliability, accuracy and principal usage.The main application of this analyser was in stope planning and design whereby several thousand drill-core and Wall-chip samples were analysed. It was also used as an aid to underground grade control of stopes where ore dilution by supporting barren backfill was a problem.

Jan 1, 1984

By M S. N Hadi, J Hossein

Numerical modelling is extensively used in civil and mining engineering applications because of cost and risk problems associated with different experimental studies. In this study, the effect of resin thickness was evaluated in bolt-grout-concrete interaction and bending behaviour of a fully grouted bolt installed across joints in post failure region. Tests were conducted in 20 and 40 MPa concretes, and modelling simulations were made, using ANSYS version 8.1, to include both with and without different pretension loads. It was found that in all resin thickness, both the strength of the concrete and bolt pretension had major influences on the shear resistance and shear displacement of the reinforced medium. Also it was found that the strength of the surrounding concrete is more important than that of the grout thickness in both the shear resistance and shear displacement when the bolt is pretensioned.

Jan 1, 2005

By Ito H, Noguchi F, Ueda Y

DTA curves of synthesis lead sulfide and commercial. lead concentrates during oxidation were measured to clarify the mechanism of ox- idation of lead sulfide. The oxidation reac tions could be divided to elementary reactions with production of basic lead sulfates such as 2PbO PbSO4. An existance of iron sulfide played an important role of the oxidation of lead concentrates. The oxidation rates of lead sulfide were measured in the wide range of oxygen potenti- als using IR type SO2 gas-meter. The oxidation rates under low Po 2 which corresponds to the direct oxidation smelting were much lower than those obtained under high Pot. The combustion temperatures of lead sulfide were also measured by hot thermocouple method. Those values were extremly low compar- ing the oxidation temperatures obtained by DTA.

Jan 1, 1987

By Grey D, Turner R, Capsanis J

Coal fines are recognised to have a major impact on the cost and efficiency of the recovery of saleable coal. Fines affect the productivity of the whole mining cycle because of the low yields obtained in washing this material as well as affecting the moisture content and handling characteristics of the final product.In 1990, Coal and Allied Hunter Valley Mine initiated an internal study into coal fines based on the assumption that a reduction in fine coal in ROM material will lead to increase yields in the preparation plant. The initial results of this study indicated that the level of fines in the ROM coal can be reduced by more than 40 per cent by simple changes in blast design and implementation.

Jan 1, 1992