Search Documents

By B Belle

In a deep, gassy predrained coalmine, ventilation and goaf drainage systems act as critical controls to manage longwall (LW) panel return gas levels. The goaf capture efficiency of most LW panels ranges from 45 to 85 per cent based on the gas domain at respective workings. Recent operational experiences have indicated that 50 m goaf hole spacing is optimal for management of high production retreat gassy LW panels, where the probability of goaf hole failures are frequent. Due to the horizontal stress direction geotechnical issues, goaf hole failure just behind the LW face is a recurring challenge resulting in significant and immediate increases in LW panel return gas levels. This paper presents a successful implementation of an innovative LW tailgate (TG) road cut through seal goaf fan/venturi system. The system incorporated a 17' (400 mm cased) hole drilled to 320 m deep in a perimeter roadway on a retreating LW TG road drawing the working seam horizon goaf gas behind the perimeter of seals. The surface goaf fan/venturi system was aimed to safely exhaust the LW deep goaf gas and thus withhold the goaf stream spillage to TG drive area and reduce the panel gas load by controlled operation of the system using continuous monitoring of CH4, CO and O2 levels. This control philosophy was made operational without impacting the use of the perimeter inbye ventilation shaft used for mine cooling and providing additional ventilation dilution capacity. The instantaneous reduction in TG gas levels of up to 0.3 per cent was observed even when the LW was 300 m away from the c/t seal goaf hole. Success of this concept TG seal goaf gas control system used even when the LW was 1300 m outbye has become an inventory of additional control for future deep and long LW blocks. This paper attempts to share the design process in addressing other risks and desired outcomes in managing the LW gas levels.CITATION:Belle, B, 2015. Innovative tailgate mobile goaf gas management in two gate road longwall panels – concept to implementation, in Proceedings The Australian Mine Ventilation Conference, pp 31–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M A. Noppé

"Investors and other stakeholders assessing the risk, opportunity and relative value associated with a resource project need to appreciate the project in its correct context. Errors, omissions, biased reporting or conflicting information in project reporting may lead to a misinterpretation of technical and financial results, resulting in biased estimates or assumptions on project value.This paper provides a simple ‘Resource Project Framework’ for presenting a project’s status that may be readily benchmarked against other similar projects and to illustrate the stages required to advance the project outcomes to higher levels of certainty. The framework draws on definitions and guidelines readily available in various resource industry reporting codes and public company reporting requirements.The framework assesses three key areas for placing a resource project in its correct relative context, namely:the project development stagethe confidence in the Exploration Results, Mineral Resources and/or Ore Reservesthe level of accuracy, precision and confidence in the technical and economic studies supporting the reported results or options for the project.The application of the Resource Project Framework is illustrated using two project examples, one from publicly reported company project releases and the other for two development projects.CITATION:Noppé, M A, 2016. A framework for presenting and benchmarking resource projects, in Proceedings Project Evaluation 2016, pp 260–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By A Vakili, F Harvey, H Greaves

Mine seismicity is one of the most difficult geotechnical risks to manage in seismically active mines. There are currently some established empirical and statistical methods that provide quantitative measures for seismic hazard assessment in operating mines. However, these methods are mostly suitable for quantifying the current or historical seismic hazard and often cannot be directly used to forecast the future hazards. Numerical modelling is the only analytical tool that can capture the level of complexities required for a meaningful analysis of mine seismicity and therefore to facilitate a reliable forecast of future hazards. However, there is currently no widely accepted and established guideline and methodology for analysing and forecasting mine seismicity using numerical modelling. This paper first provides a background on previous published studies on this subject and then outlines the key aspects that can affect the reliability of the forecasting for mine seismicity. These aspects include a) processing of historical seismic data, b) selection of suitable numerical modelling approach, c) Post-processing and interpretation of the model outputs. A case study is then presented for the Gwalia Deeps Mine where a new framework was developed to forecast future mine seismicity. High-quality seismic data for a period of five years was used for back-analysis and comparisons with the numerical modelling outputs. After development of the method, the future seismicity was forecast for the next 12 months and the actual seismicity was monitored against the forecast during this period. Results of this study shows promising potential for the proposed framework to be applied more routinely and at other mine sites. However, more validations are required at Gwalia Deeps mine as the mine proceeds to deeper levels. In addition, the method needs more improvements and should be tested and validated at other mining operations before it can be established as a proven method. CITATION:Vakili, A, Harvey, F and Greaves, H, 2018. Forecasting mine seismicity – towards a more established methodology, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 207–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Napitupulu P

PT Freeport Indonesia currently operates a concentrating complex capable of milling 127 000 metric tonnes per day of copper and gold hearing ore. The facilities consist of both a conventional crushing, ball mill and flotation circuit and a SAG, ball mi

Jan 1, 1997

By ALAN J. HARGRAVES

It is normal that Shepherd and Rixon, in their contributed discussion (this issue) see differences with Hargraves (1983), as it exemplifies the present uncertain situation worldwide, a situation expected to remain until better understanding and wider agreement lead to the real goal of the prevention of instantaneous outbursts of coal and gas.

Jan 1, 1983

This paper describes the technical development of the Newman beneficiation plant over its 23 years of operation and how this development relates to the mine ore reserves of high-grade and low-grade ore. It also discusses the importance of the beneficiation product grades in the overall blending of shippable products from a range of mines to optimise overall ore resource utilisation. Also discussed is the importance of the ore reserve reconciliations in resource utilisation. Data is provided on the capacity and quality improvement results of the plant upgrade, carried out in 1999. This shows how the original capacity upgrade targets have been exceeded and the additional quality benefits that have been obtained from this capacity.

Jan 1, 2002

By P W. Cleary, G K. Robinson, M D. Sinnott

Discrete element modelling (DEM) is a research tool that involves numerically solving the equations of motion of large numbers of particles. It can be very useful for investigating mechanisms that can lead to bias when extracting samples from material as it is carried on a conveyor belt or as it falls from the end of a conveyor belt. DEM is more realistic than conceptual models and mathematical models; but it is not as realistic as physical experimentation. Its primary advantages over physical experimentation are that it is cheaper and that it allows many factors to be varied while keeping other factors unchanged.This paper reviews our investigations of the performance of sampling systems by using DEM. The sampling systems investigated include falling-stream cutters, cross-belt cutters, Vezins and a device called a ætrue-beltÆ cutter, which is being developed. The purpose of the review is to explain what DEM has contributed to the theory and practice of sampling, and to indicate what it is likely to be able to contribute in the future.CITATION:Robinson, G K, Cleary, P W and Sinnott, M D, 2012. How discrete element modelling is influencing the theory and practice of sampling, in Proceedings Sampling 2012 , pp 15-20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By J Pan, G Qiu

In this paper, an analysis is made of the present situation in the Chinese steel industry and its demand for iron ores. It is shown that the demand for iron ores has been growing substantially with the rapid development of the steel industry all over the world, especially in China. However, the iron ore market is currently in the situation where supply exceeds demand due to the economic crisis, with more investment in mines and less output of steel for several years ahead all over the world. Gigantic pressure is confronting the Chinese steel mills due to the too high and irrational price of iron ores. It is time to return the price of iron ores to a normal position much closer to their value. More attention has therefore been paid to developing low-grade and complex iron ore resources in China due to the irrational price of imported iron ores. More innovative mineral processing processes have been developed to tackle these complex resources. A systematic introduction to the development of beneficiation processes for low-grade iron ores is provided, including upgrading low-grade siderite, limonite, micron sized haematite and magnetite resources.

Jan 1, 2009

By S J. Schafrik, E S. Gilliland, E C. Jong, J Waynert, C W. Weiss

Two commercially available through-the-Earth (TTE) communications systems were evaluated at an active underground longwall mine in West Virginia. One system utilises magnetic field (H-field) antennae while the other system utilises electric field (E-field) antennae to achieve communication. A large portion of this mine is overlain by an inactive gas-oil field composed of densely spaced wells. This feature provided a unique opportunity to determine the impact of cased wells on both TTE technologies. The following communication modes were investigated: surface to underground, underground to surface, underground to underground and real-time two-way communications. Standard deployments of the TTE systems using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations under certain circumstances. As a result, the design and deployment that will optimise TTE transmissions are unique to each system and to the specific area of the mine. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivity. The performance of these two TTE systems suggested that one may be preferable over the other depending on the conditions present during deployment.CITATION:Jong, E C, Schafrik, S J, Gilliland, E S, Weiss, C W and Waynert, J, 2015. Pairing magnetic and e-field through-the-Earth communication systems based on mine site conditions, in Proceedings Third International Future Mining Conference, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By A Scott, I Onederra

Most iron ores occur in mine benches as complex mixtures of lithologies and ore types. This significantly complicates their characterisation for both blast design and fragmentation modelling. A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful engineering models are currently available to blasting engineers and consultants, and more sophisticated approaches using mechanistic descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The engineering or empirical models that are in more general use within the industry, such as the Kuz-Ram model, require appropriate data if they are to generate useful fragmentation predictions. Some of these models have reached significant sophistication and have made very useful contributions to both routine blasting operations and the exploration of new blasting paradigms. However, these models struggle to adequately deal with rock that is as complex as iron ore. This paper reviews the characteristics of the most successful blast fragmentation models available to the industry and discusses approaches to the derivation of suitable rock mass properties to adequately describe blast fragmentation in a range of iron ores.CITATION:Scott, A and Onederra, I, 2015. Characterising the blasting properties of iron ore, in Proceedings Iron Ore 2015, pp 481–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The carbonatite-hosted apatite deposit at the Cajati open pit mine in the Jacupiranga igneous-carbonatite complex is located in south-eastern Brazil. The major styles of apatite mineralisation include veins or veinlets, small pods or patches, disseminated apatite and locally massive aggregates. The metallurgical concentration of the apatite is accomplished by grinding the carbonatite, removal of magnetite with a magnetic drum, size classification with cyclones and flotation to suppress carbonates and collect apatite. To examine the character of the apatite grains and to apply those observations to apatite beneficiation, specimens of carbonatite were collected from recent exposures in the mine and from selected drill holes. This study utilised a variety of microscopy methods, including transmitted and reflected light, cathodoluminescence (CL) and scanning electron microscopy with wavelength-dispersive spectrometers for mineral compositions. It was found that LREE, Na and Sr are the main elements replacing Ca in the apatite, with relatively low oxide contents (<0.5 per cent, but up to about one per cent for Sr). LREE and Sr contents consistently increase in the latest intrusions (C4, C5 and SP24). Chemical and morphological modifications of apatite were recognised to be related to detrimental effects on flotation recovery. Three examples illustrate this relationship: 1.  Apatite with reddish CL is fractured. Locally that apatite exhibits no CL due to CL quenching caused by iron entering the apatite structure.2.  Apatite from the xenolith-rich area exhibits abundant fine, platy silicates that appear to interfere with flotation and lower apatite recovery.3.  So called æhardÆ apatite, which is more difficult to grind, occurs in an area in the mine that was affected by hydrothermal activity. That activity is evidenced by the development of a bright, white CL rim in the apatite, and by the presence of late veins of carbonates and sulfides that fill fractures and appear to contribute to higher cohesiveness of those apatite grains.

Jan 1, 2008

By Garg R. K

Himalayan ranges on the northern border of India are source of many perennial rivers and suitable sites for large dams have been located therein. However, Himalayas are young mountains and comprise of comparatively weaker rocks having adverse geological features like shear seams, thrust zones, minor and major faults and intense jointing. Tehri dam project under construction, is located in lower Himalayas. It envisages construction of a 260.5 m high earth and rock fill dam and an underground power station of 2000 MW (Eight machines of 250 MW each, four of which will be reversible) installed capacity. This dam will be the highest and the underground complex will be the largest to be constructed in India in the Himalayas. The under- ground complex comprises of 25 km of tunnels varying in diameter from 6 m to 11 m and seven large cavities of various sizes, the biggest being 22 m in width, 194 m in length and 65 m in height. Rock formation in the power house complex belong to phyllites having various joint sets spaced from 0.5 m to 3 m. Due to the poor geological conditions and closely spaced net work of large cavities, the planning, analysis and design of the cavities is a challenging job. Many aspects have to be considered in determining the sizes, locations and orientations of the various cavities taking into account the properties and jointing pattern of rock mass, functional requirements and economics. Correct evaluation of loads and forces is necessary for economical design of supporting system for the various cavities. Rock loads on the roof of cavities and their supporting system will be assessed with the help of the latest methods. The stability of the rock mass around the cavity will be evaluated by elasto- plastic method using finite or boundary element techniques. A scheme of field investigations, laboratory tests and instrumentation for deter- mining rock properties in preconstruction stage and for monitoring behaviour of the underground cavities during and after construction is envisaged.

Jan 1, 1987

By W A. Ducker, R-H Yoon, M Mao

Froth flotation relies on an attractive force between a particle and a bubble to selectively extract particles from a mixture. The range and magnitude of this attractive force is an area of ongoing investigation. We describe measurements of the effect of dissolved gases on the long-range attractive surface forces between a silica plate and a glass sphere in aqueous octadecyltrimethylammonium chloride (C18TACl) solutions. The measurements follow on the work of Sakamoto et al (2002) who have concluded that long-range interactions occur in air-equilibrated surfactant solutions but not in degassed solutions. In the present work, we have measured attractive forces that have a much larger in magnitude than the expected van der Waals force in solutions that were degassed by the same procedure used by Sakamoto et al (2002). We find that the forces are most attractive at 5 + 10-6 M C18TACl, which is close to the charge compensation point (ccp) of the glass sphere. At this concentration, the attractive force decays exponentially with distance and the decay length is 34 in air-saturated solution, and 38 nm in degassed solutions. In both air-equilibrated and degassed solution, the force is quite sensitive to the concentration of surfactant. The force is also sensitive to the pH. We note that our degassing procedure increases the pH of the solution from about 5.7 to 6.6 (presumably by removal of dissolved CO2). We find that the forces measured in degassed solution can be reproduced by using a solution that was equilibrated in air, then the pH was increased by addition of NaOH. Therefore, we conclude that the main effect of degassing in our experiments is to raise the pH. We show that the range and magnitude of the attractive force decreases in the presence of salt (NaCl). This suggests an electrostatic mechanism for the attraction. Possible mechanisms for the attractive force are examined, including the mechanisms that rely on a patchy coverage of surfactant on the silica surface.

Jan 1, 2005

With the use of 86 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt. Lyell Mining & Hailway Co., it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5,000 feet of boring the total cost of new parts noted on this line. (See l"ig. 1.) Thus at a glance it is possible to see... the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this difficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component. As before the cost of new parts are taken at each 5,000 feet bored. (See Fig. 2.) The curves so obtained are particularly interesting for two reasons:1. Each machine has its characteristic curve.2. The curve always steepens.Some machines are found to have relatively flat curves, others flat curves for approximately 15,000 feet of boring, and others steep gradients from the begining.This demonstrates that it is not always economic to discard a drill after it has been in service for a certain length of time or after it has bored a specified number of feet. Each drill has its own characteristics and so must not be regarded as one of a class, but considered on its own performance.The following use of these curve diagrams has been made to determine whether a machine has reached the end of its economic life. Figure 3 shows...

Jan 1, 1942

Structural geological modelling is a process which results in a 3D computer model that represents the essence of the geological and structural understanding of an area and is presented in a way that is directly useable, typically by internal customer groups. BHP Iron Ore operates a number of open cut iron ore mines in the Pilbara Region of Western Australia. The largest mine is the Mt Whaleback Mine located at Newman close to the southern margin of the Pilbara Craton. The structurally complex Mt Whaleback Mine is the largest metalliferous single pit open cut mine in Australia with over 1.6 billion tonnes of original iron ore resource. Additional to the Mt Whaleback Mine, a number of satellite open cut iron ore mines are operated by BHP Iron Ore (BHPIO) in the Newman area. BHPIO also operates the Yarrie mine approximately 400 km north of Newman at the northern edge of the Pilbara Craton Most of the BHPIO mines are located in the Archean- Proterozoic Hamersley Province that overlies the Archean granite-greenstone terrain of the Pilbara Craton. The orebodies are considered to be the result of supergene enrichment of the approximately 2.5 Ga Brockman Iron Formation and the slightly older Marra Mamba Iron Formation. Folding represents the most prevalent and penetrative structural element in the Newman area. Four folding phases have been identified regionally (Fj, F2, F3, F5), while a more local folding deformation (F4) developed mainly in the Mt Whaleback and Orebody 29 mine area. A northeast trending, southeast dipping, 45 km long, high angle, normal fault zone, the Whaleback Fault Zone, cuts through the Mt Whaleback mine resulting in an approximately 1400 in gap in stratigraphy. Additionally, two large, low angle, normal faults, the East Footwall Fault and the Central Fault, are present at the Mt Whaleback Mine. During the formation of supergene orebodies, up to 40 - 45 per cent volume loss occurred resulting in local non-tectonic deformation in the orebodies.

Jan 1, 1997

By S Prakash, P S. R Reddy, S K. Biswal, V N

The beneficiation potentials of two Indian iron ore slime samples by flotation technique using both cationic and anionic collectors are investigated. The direct and reverse flotation of slimes using oleic acid and dodecylamine as the collector have been studied using both conventional cell and flotation column to upgrade the iron content. The characterisation studies of iron ore slimes indicated that the samples are extremely fine in nature and contain substantial amounts of martite, magnetite, goethite, limonite, kaolinite and quartz beside hematite as the dominant iron mineral phase. The samples on average contain around 52 - 58 per cent Fe, four to seven per cent SiO2 and five to six per cent Al2O3. Taking into account the physico-chemical properties of the slimes, it is attributed that both the samples need to be deslimed by hydrocyclone before flotation. The results of both cell and column studies on sample I showed that a feed containing 57.5 per cent Fe could be upgraded to 65.5 per cent Fe at 50 per cent overall recovery with simultaneous decrease in SiO2 and Al2O3 content to 2.3 per cent and 1.8 per cent respectively by using oleic acid as the collector. In the case of sample II, it has been established that reverse flotation of silica is the better technique to improve both the grade and recovery of iron. Batch flotation studies in cell indicated that a product with 63.1 per cent Fe could be obtained at 40.0 per cent yield with 63.6 per cent iron recovery by the combination of reagents such as gum acacia, sodium hexa meta phosphate and dodecylamine. The performance of column flotation techniques is far superior to that of the cell with respect to both grade and recovery. The concentrates are found to be quite suitable for commercial exploitation as pellet feed.

Jan 1, 2005

Chile, which hosts around 30 per cent of the worldÆs copper resources, is now the largest producer and exporter of copper. Chilean copper output accounts for more than one-quarter of total worldwide production. An increase to around 40 per cent is forecast by the end of the century. In addition, Chile ranks eighth in silver production and 11th in gold output. In Chile, mining generates more than eight per cent of the countryÆs GDP and the total value of mineral exports is more than US $7.85 billion corresponding to more than 25 per cent of South AmericaÆs mineral production. The rate of growth of Chilean mineral production is indeed impressive. Table 1 shows that in the period 1969 - 1998, copper annual production increased 564 per cent from 667 000 t to 3 764 000 t. Gold production went up 27 times from 1827 to 49 770 kg. Silver output grew 1219 per cent from 95 650 kg produced in 1969 to 1 166 380 kg in 1998. Several facts explain this dramatic increase of production, but the most important was the success of exploration sustained over the same period. This resulted in the discovery of several world-class deposits which when developed into mines, account for much of the production increases. Therefore, this summary review shows the success of basic exploration carried out during the last 30 years in the Chilean territory. The review is based on data already published in different specialised mining books or magazines. It only includes those world-class discoveries not the lesser discoveries important at local scale. All figures were calculated using 1998 $US dollar and average estimated metal prices valid for 1999: copper $US 1653 per t ($US 0.75 per pound), gold $US 9452 per kg ($US 294 per ounce) and silver $US 177 per kg ($US 5.5 per ounce).

Jan 1, 1999

By R Strand, B Usher

Environmental compliance and mine designs are increasingly including assessment of flows and water qualities as a key driver to decision-making over life-of-mine. Integrated site-wide water quality models linked to dynamic water balances have been used for regulatory submissions, feasibility studies, operating mines and mine closure studies. These models, developed in GoldSim, link aqueous chemistry to the physical system of the site-wide water balance. Geochemical mechanisms included are determined from geochemical characterisation and site water monitoring, depending on the data availability at each site. External geochemical modelling using PHREEQC, version 2 (by D?L?Parkhurst and C?A?J?Appelo) and Geochemists Workbench (GWB), (by C?M?Bethke and The Board of Trustees of the University of Illinois) identifies the most important geochemical processes to be included in the model as a series of geochemical mechanisms which include source term loading rates, pH-buffering and equilibration of water quality. Water balance components include seasonal flow variability; waste facility water storage and system lags; run-off variability; milling processes and tailings production as a function of ore types; simulation of automated and scheduled maintenance of settling ponds; water re-routing for water treatment and freshwater demand, usage and storage.Case studies illustrating the use of these models for regulatory submissions and mine feasibility studies in a variety of climatic and regulatory environments show the utility and applicability of these models. Site-specific examples of these models developed by Klohn Crippen Berger Ltd are currently used at operating mines across the world. One of the larger mines where this is used is a mature poly-metallic mine in South America where the model has aided mine managers in understanding how various planned initiatives and potential water options will result in changes to flows and water quality. It is used regularly to inform water and waste management to minimise impacts to the receiving environment as a consideration of both flows and concentrations. The mine has also used the model in support of water treatment design, regulatory submissions and mine closure planning.Further examples of feasibility and operational/compliance assessment in arid and strongly seasonal environments for planning, regulatory and closure consideration of mine wastes and pits have shown the utility and usefulness of these approaches for a range of mining operations at various stages of mine life.CITATION:Strand, R and Usher, B, ?2014. Integrated site water balances and water quality models for decision-making over life-of-mine, in Proceedings Life-of-Mine 2014 , pp 271–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The Callie Underground Mine is located in the Tanami Desert 560 km Northwest of Alice Springs in the Northern Territory and is currently operated by Newmont Australia Limited with all mining activities carried out by Henry Walker Eltin. Callie was discovered in the region in 1991 with the box cut portal commenced south of the pit in 1995 and underground ore production commenced in 1998, after completion of the profitable Callie Open Pit. Development is currently occurring at depths of over 700 m with the decline currently below the 640 Reduced Level (RL) level (surface RL of 1400) with production haulage from 600 m below the surface. The combination of auto compression, a moderate geothermal gradient of 2¦C/100 m and diesel heat transfer causes the wet bulb temperature of intake air at the bottom of the mine to be typically 5¦C higher than on the surface. Wet Bulb temperatures can be up 5¦C higher again in active areas under secondary ventilation. During the 2002/2003 wet season many activities in the lower levels of the mine were stopped due to miners experiencing adverse heat related symptoms or the temperatures exceeding the Underground Heat Management Procedure stop job criteria of 32¦C wet bulb. To improve the working environment, combat the heat related illness and improve operational efficiency, a temporary 1.8 MW refrigerated cooling plant consisting of three 600 kW modules were installed underground to provide bulk air cooling for the lower levels of the mine during the 2003/2004 wet season. Several studies have been conducted in relation to future ventilation demands at Callie and all came to the conclusion, that some mine cooling will be necessary for Callie to meet the high production and development demands. This paper will describe the ventilation network at the Callie Underground operation focusing on the installation, operation and effectiveness of the temporary underground refrigeration plant.

Jan 1, 2005

By S Joyce, Z Agioutantis, D van Zyl, D Shields

Over the past 15 years, the mining industry has begun to incorporate the concepts of sustainable development and sustainable mining practice across the life cycle of mineral operations. This requires addressing economic issues, community impacts and concerns and environmental protection, and is captured in part by the phrase ‘design for sustainability’ (McClellan et al, 2009). Over the same period, the industry has seen a gradual decline in ore grades for many mineral commodities. As a result, large volumes of tailings and mine waste rock are being produced around the world, and it is expected that the annual production volumes of these materials will increase, even if there is not a significant change in the demand for materials.Another related thread of change has been the realisation that societies need to move away from linear economies (raw materials, production, consumption, disposal) towards more circular ones. This will help societies become more resource efficient, which is defined by the United Nations Environment Programme as reducing the total environmental impact of the production and consumption of goods and services, from raw material extraction to final use and disposal. The goal is to create more with less and deliver greater value with less input. Circular economies require thinking in terms of the waste hierarchy (reduce, reuse, repurpose, recycle, recover, landfill).The challenge is that the waste hierarchy was originally designed to address embodied mineral content in products rather than mine waste and tailings generation. It will need to be reconsidered in a mine life cycle context, focusing on a value-based conception of waste (Van Ewijk and Stegemann, in press).In parallel to these changes, it has remained an imperative in the mining industry to dispose of these waste materials as economically as possible while protecting the environment. Single handling of these materials has been the main target, which reduces the life cycle costs of their management but may make reuse of waste and tailings technically more difficult or economically infeasible.This presentation explores a rethinking of the large volume earthen material waste issue at mines. The underlying theme is that some or all of these materials can be valuable resources for the future that can positively contribute to sustainable development. These resources can offer economic gains to firms, communities and societies; contribute to environmental well-being; enhance social interactions with the previously mined landscape if handled properly; and, with proper policies in place, reduce governance commitments. Each of these topics will be briefly explored. This will be followed by a discussion of approaches to manage design and operations to allow future resource recovery.CITATION:Van Zyl, D, Shields, D, Agioutantis, Z and Joyce, S, 2015. Waste not, want not – rethinking the tailings and mine waste issue, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 7–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015