Search Documents

By S Maritsa, D Simbi, E K. Chiwandika, S M. Masuka

The steel industry is facing challenges on a global scale that include depletion of resources, huge energy consumption, and the emission of CO2. The demand for iron products is increasing due to the increased infrastructural development. Zimbabwe produced cast iron from scrap metals. However, there is currently a shortage of scrap, and yet Zimbabwe is rich in limonite ores that are currently being underutilised. The possibility of using limonite ore as a sustainable feed for pig iron production was investigated by preparing some limonite ore carbon composite pellets. The results showed that the addition of coal to the limonite ore and calcium carbonate mix to form the composite pellets resulted in a decrease in the drop number as well as the dry compressive strength of the composite pellets. This research aims to improve the physical properties of the green pellets by the careful addition of hydroxyethyl cellulose as a binder that was found to improve the physical properties of the green pellet. This is important for materials handling during the production process of the composite pellets. Results showed that the drop number was substantially improved by the addition of 0.4 wt per cent hydroxyethyl cellulose while the dry compression strength improved from 2.5 kg/pelIet to around 23 kg/pellet irrespective of the amount of binder added. The binder improved the physical strength of the iron-carbon composite pellets enough to allow for large-scale production of the pellets that can be an alternative and sustainable feed for cast iron production. However more results on the indurated compression strength and other properties such as the reduction degradation index, swelling index, and the reducibility test are required.

Jun 19, 2024

By G Hall

BHP BillitonÆs (BHPB) Yandi ore deposit is a channel iron deposit (CID) in the Pilbara district of WA. The ore is predominantly a goethite-hematite pisolite and overlays a clay at the base of the deposit. Knowledge of the location of the contact prior to mining is critical to maximise ore extraction and minimise contamination from and mining of the underlying clays which contain high levels of alumina. The contact between the iron ore and the clay is highly irregular. Traditionally the contact has been delineated by closely spaced drilling û this can be expensive and since each drill hole only provides a point sample measurement, irregularities in the contact surface can be missed. In September 2001, three high resolution geophysical techniques were trialled to see if they could be used to improve the efficiency and accuracy of ore delineation. The three techniques were resistivity imaging, ground penetrating radar and electromagnetic conductivity imaging. The resistivity data showed a favourable correlation with the available ground truth data from drilling. Using this ground truth data as a calibration, an interpretation of the depth to the base of the channel iron deposit (CID) ore was constructed for the areas surveyed. A significant attribute of the method is that the position of the base of the ore is imaged continuously along the lines that are surveyed rather than at discrete points. No continuous well defined ground penetrating radar (GPR) reflections were observed from the base of the CID ore. There did appear to be some correlation between the range of echo times that reflections were observed and the drill data, however the precision to which the range of echo times could be estimated was of the order of several metres and therefore not adequate to replace current procedures. The electromagnetic data showed good correlations with the existence of shallow clays but did not discriminate between variations in CID ore depth. This technique is therefore not suitable for mapping the base of the CID ore but may still be useful as a rapid tool for mapping the position of clay bands.

Jan 1, 2002

By R Carstens, L Munsamy, L Prinsloo, C Huang, C Zhang, R Liang, I Canbulat

With recent advances in machine learning, data-based automated decision-making has been proven successful with promising outcomes in many industries. Its application in the mining sector can be ground-breaking; particularly the data-driven analytics that can support decision-making in the mine and consequently enhance mine safety, efficiency and sustainability. However, the current data science applications in the mining industry are mostly noncomprehensive, especially inadequate in evaluations, thus often requiring further study to be potentially beneficial to operations. Furthermore, it was found that existing literature paid limited attention to understanding the role of such techniques. Hence, in this paper we aim to build an end-to-end machine learning powered data-driven framework for intelligent geo-hazard analytics to support decision-making for underground mining data management, where multiple types of data are managed in an integrated database to support the unified machine-learning model. Here we present the framework as data-driven workflow processes, including data gathering, data preparation, data processing and data presentation. In addition, we present an application scenario of the proposed framework, where falls of ground (FoG) is managed with the historical FoG investigation reports, related panel hazard ratings, compliance data and rock mass characteristics. A demonstration can be dynamic forecasting of high-risk areas for FoG based on both spatial and temporal factors, including a 3D data visualisation. Such a scenario shows the potential of the proposed framework to establish connections among various data fields across a diverse category of data. Furthermore, the results offer important insights for ground instability management and can potentially optimise the underground operation flow.

Nov 29, 2022

By H Kurth, L Balzan

The potential for bulk diversion was identified and quickly implemented following the development of bulk sensing technologies applied to conveyed flows. In the early 1980s real time analysis of ash in coal was intended to improve the understanding and control of quality variability. By the end of the 1980s approximately 5% of coal analysers installed were being utilised for bulk sorting; diverting flows to create stockpiles to improve blending flexibility and boiler feed consistency, diverting waste material, or bypassing the beneficiation process when the coal met product quality criteria. In the 1990s bulk sensing and sorting utilising natural gamma detection was applied to conveyed waste in gold-uranium mineralisation and allowed ore to be recovered and processed that would otherwise have been discarded. Further applications developed in the iron ore sector where product quality ore could be diverted to bypass beneficiation and save significant unnecessary processing costs and improve recovery by avoiding process inefficiency losses. Plant capacity was freed up to be utilised by material that required processing. Similar benefits became evident in the phosphate industry and in base metals where multi-elemental analysis using Prompt Gamma Neutron Activation Analysis provides ideal opportunities to representatively measure 30 second conveyed increments at high accuracies. This has been successfully adopted in copper, nickel, platinum and lead-zinc to improve waste removal after primary crushing to eliminate unnecessary expense and improve plant efficiency. The benefits include increased output from existing operating capacity, significant reductions in consumable costs and generation of fewer detrimental waste streams. The paper outlines the technologies and discusses case studies covering the above commodities, demonstrating the immense value that representative real time measurement of conveyed flows can create. Measurement data concurrently provides multiple benefits in operational performance besides sorting, through ore reconciliation, ore blending, feedforward control and metal accounting, adding further value.

Nov 10, 2020

The Newcrest Mining Limited Telfer Gold Mine consists of an underground sublevel cave (SLC) operation located 734 m directly below active open pit operations. Open pit and underground current production rates are 50 million and 5.7 million tonnes per anum (Mt/a) respectively. The SLC was initiated in late 2006 with breakthrough planned to occur on the 5484 bench of the west wall in late 2009. Risk to the south ramp was identified during this time, resulting in the construction of the north ramp. The SLC was continually tracked from initiation with a suite of monitoring systems and managed with a Major Hazard Management Plan (MHMP) and associated Trigger Action and Response Plans (TARP). At breakthrough the eastern limb of the cave was located within a 70 m horizontal distance from the south ramp. The south ramp was closed in October 2009 due to significant slope deformation, extensive cracking in the berms and batters between the ramp and breakthrough bench and a major failure 250 m to the north of the cave breakthrough. Wall response was first identified from slope deformation measurements taken by the wall monitoring radar in May 2009, at which point the SLC was 160 m from breakthrough. The impact of the SLC on the slope is a unique case with the monitoring systems in place able to provide data on the slope reaction to the SLC progression. This paper will discuss the management of the south ramp such as the early interpretation of risk associated with cave breakthrough, monitoring systems implemented to track the cave progression and wall deformation, data integration and interpretation and risk management. Following the closure of the south ramp further instrumentation programs and risk assessments were conducted to determine the risk of re-opening this haulage route. The outcomes of this program will also be presented.

Nov 25, 2010

By M A. Llano-Serna, D J. Williams, L Bu

Tailings dam failures continue to occur worldwide at an unacceptable rate, averaging two events annually over the last 100 years. Furthermore, tailings dams continue to grow in size, increasing the potential release of tailings and water should they fail. Tailings are generally deposited in a slurry state, with the potential to flow if containment is lost. Understanding the generation and propagation of excess pore water pressure on failure is critical to predicting the flow and run-out of tailings. This paper presents numerical modelling using the material point method indicating that tailings run-out processes may be self-enhanced by the excess pore water pressure induced during the collapse of the containment. Moreover, it is shown that geomorphological features, such as the slope and its surface roughness downstream of the tailings dam, influence the pore water pressure dynamics upstream of the advancing toe.CITATION:Llano-Serna, M A, Bu, L and Williams, D J, 2018. Excess pore water pressure induced during tailings run-out, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 377–383 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By P Viljoen, A Holland, C Parken

In the raisebore industry, there are two known methods of removing large diameter reamer heads once the reaming of an underground shaft is complete: 1. Lower the reamer head to the base of the shaft and use a thermal lance to cut the drill string and drag the reamer away from the hole. This method exposes the person doing the job to falling rocks from the unsupported mineshaft, a hazard which is difficult to control and has caused fatalities. 2. Install breast plates in the backs above the reamer head at the top of the hole, and use air hoists to lift the reamer out of the hole. Steel beams are then placed across the hole which the reamer is lowered down onto, dragged forward away from the hole, disassembled, and removed. This method is time consuming, expensive, and complex in the controls required to ensure safe completion of the job At Carrapateena, the air hoist method had been successfully used, however, with the cost involved and the complexity of this process, development of an improved and fit for purpose reamer removal method was pursued. OZ Minerals collaborated with Pybar to develop an industry first application of Enerpac SL100 lift and shift technology; a track mounted system with hydraulic lifting units that can both lift the reamer out of the hole and tram it back along the tracks away from the hole. A key component of turning the idea into a reality was by establishing a truly collaborative relationship between client and contractor. When the SL100 mobile gantry arrived, it was set up in Adelaide and trialled with the whole raise bore crew attending the two-day workshop and risk assessment; a rare opportunity for drillers. There have now been five successful reamer removals with the SL100 mobile gantry at Carrapateena. It has proven to be an efficient process with the entire process from setup to demobilisation taking less than 48 hours. This new way has completely removed hot works and uncontrolled hazards from working at the bottom of a shaft. It has also saved the reamer stabiliser from being cut and thus wasted. Exposure to the open hole has been minimised significantly as assembly of the SL100 is completed well forward of the open hole. This new process is exponentially safer, quicker and cheaper.

Mar 15, 2021

By M D. Basuki Dwi Priyono

The Toguraci low sulfidation epithermal gold vein deposits are located 2 km WSW from the Gosowong mine and form part of the Gosowong Goldfield. The goldfield lies within a Neogene magmatic arc on Halmahera Island, North Maluku Province, East Indonesia. The terrain is moderate to steep, rainforested, and poorly outcropping. Exploration and mining operations are being carried out within the PT Nusa Halmahera Minerals Contract of Work (exploration tenement) jointly owned by Newcrest Mining Ltd (82.5 per cent, operator) and PT Aneka Tambang Tbk. (17.5 per cent). First pass exploration of the Gosowong area began late 1992 resulting in the discovery of weakly developed porphyry copper mineralisation (named Bora) at Toguraci in 1993. Early in the evaluation of this porphyry an overprinting epithermal Au/Ag mineralisation event was recognised, however exploration focus remained on the Bora porphyry deposit for some time. The discovery of the nearby Gosowong epithermal gold deposit and the exploration of other prospects in the area further diverted attention and funds from Toguraci. It was not until year 2000 that Toguraci was seriously reevaluated as part of a detailed appraisal of the epithermal gold potential within a 5 km radius of the Gosowong gold mine. A fly-camp based drilling campaign using man-portable rigs was undertaken between August 2000 and March 2002. All exploration at Toguraci was then stopped pending government approvals to mine. These were finally issued in May 2003 and immediately drilling restarted and pre-mine approvals (eg the environmental impact study) were sought and granted. The first Toguraci gold bar was poured in February 2004. Exploration at Toguraci and elsewhere in the Gosowong Goldfield continues today.

Jan 1, 2004

By Manlapig EV, Lawson F, Clarkson CJ

A low grade middling sample from Mount Isa, Australia, assaying 31.7 per cent zinc, 12.9 per cent lead and 14.5 per cent iron was leached under atmospheric pressure in sulphate and sulphate-chloride solutions with ferric ions as oxidants. About 96 per cent of the contained zinc was dissolved into a 0.5 M H2SO4 - 0.5 M Fe2(SO4)3 solution at 90¦C within three hours from a five per cent by weight slurry density mixture. The leaching process is very temperature-dependent, suggesting a surface chemical control. In the latter stage, the leaching rates levelled off and the leaching was most probably controlled by both surface chemical reaction and diffusion processes. The addition of chloride ions in the leach solution resulted in an increase in the leaching rate. About 95 per cent of the lead sulphide contained was converted to lead sulphate which precipitated and remained in the residue. Essentially no lead remained in solution and the low chloride concentration did not affect the precipitation of lead sulphate. Half of the iron orginally present remained in the residue as pyrite although essentially all the cadmium and 90 per cent of the copper initially present were dissolved. Some three per cent of sulphide sulphur was oxidised through to sulphate, about 67 per cent was converted to elemental sulphur which can be recovered by solvent extraction, the rest remained in the residue mainly as pyrite. Ferric sulphate and sulphate-chloride solutions can be used to effectively leach finely ground lead-zinc middlings and other bulk sulphide concentrates. A complete separation of zinc from lead and silver has been demonstrated.

Jan 1, 1993

By C Linklater, A Garvie, D Kentwell

Various Australian and international regulatory bodies (Environmental Protection Authority, 2015) require an early assessment of the geochemistry of waste rock. This usually includes estimates of the locations and volumes of potentially acid forming (PAF) materials and requires sampling of the waste rock zones as well as submitting the samples for a series of tests. We know that the required number of samples will vary depending on rock type, mean sulfur levels and spatial variability of sulfur as well as total volume. The key question is how do we know when we have enough samples?This extended abstract describes the application of geostatistical methods to examine how sample numbers and sample locations influence the preliminary conclusions that may be drawn for early stage waste characterisation.CITATION:Kentwell, D, Garvie, A and Linklater, C, 2016. Geostatistics and sample numbers from an acid and metalliferous drainage perspective, in Proceedings Life-of-Mine 2016 Conference , pp 12–15 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By R Paterson, A Christensen

The routine use of gravity gradiometry for the detection of orebodies with no outcrop is now being undertaken. The commodities and orebody styles range from banded iron ore formations to volcanogenic massive sulfide (VMS) style polymetallic deposits. This recent innovation of flying gravity gradiometry was pioneered by BHP Billiton and Lockheed Martin with the Falcon technology (Lee, 2001), and now two additional systems, also using Lockheed Martin instruments, are deployed. In South Africa, magnetic gradiometry is being developed and deployed with the same objectives in mind. In this case, a system from Institute of Photonic Technology (IPHT) is being used. The detectable wavelengths from such systems have decreased to less than 200 m in the last year, and it is expected in 2011 that wavelengths to less than 100 m, with anomaly signal strengths of less than 2 Eotvos for gravity gradiometry will be viable. The key to these advances lies in the improvements of processing software and geological modelling. In particular, methods using all the tensor components are starting to be routinely deployed to filter, level and grid the observed signal. These methods do, however, require full insight and understanding of the reference coordinate systems used by the various instrument designers and survey operators. The digital terrain models need also to be observed to an accuracy of better than 20 m cell sizes, using such techniques as Lidar. Then the terrain effects can be modelled. The topographic surface represents the largest and most proximal density contrast encountered in an airborne survey. Hence terrain effects can have significant impact on airborne gravity gradiometry data. A decorrelation of the terrain effect with the observed signal requires a method of best fitting with a regional surface density. A novel technique has been developed for this purpose. This technique uses a tensor algebra to estimate a density between 1 - 4 g/cc that explains the average observed signal. Armed with this result, the anomalous buried bodies can be revealed by subtraction.

Sep 26, 2011

By P Chapman, B Moosapoor

The objective of this paper is to present the potential applications of geostatistical analyses in planning CPTu investigations, as well as interpolation of CPTu data. The paper presents a case study of a geostatistical analysis of CPTu data undertaken between 2004 and 2017 for an upstreamraised TSF located in the Goldfields region of Western Australia. An initial model is developed using the 2004, 2009 and 2017 CPTu data. The model is used to predict in situ cone tip resistance (qc) measurements, as the interested primary variable, at the selected locations where 2019 CPTu were undertaken, and the results of the prediction and the actual data are compared.

Jul 1, 2021

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By D Henderson, M Germain

The beneficiation of iron ore deposits to yield haematite and magnetite concentrates for steel making processes typically require the use of one or a combination of wet processing techniques based on gravity, magnetic or froth flotation processes. With the need for more cost-effective technologies with a lower water demand, a re-examination of dry processing techniques has been initiated. For example, a dry processing capability may offer an advantage where suitable quality and quantity of process water hinders the development of a particular resource. This paper describes recent laboratory test work for the production of high grade concentrates using dry electrostatic techniques for -300 ¦m haematite and magnetite ores and compares them with magnetic separation techniques.

Jan 1, 2009

By X Li, R Chu, X Deng

The hot-dip galvanising industry is the largest consumer of zinc, with over 40 per cent of the world’s total annual production of zinc used for galvanised steel. The dross generated in the hot-dip galvanising coating process is a valuable co-product, since it contains high quantities of recyclable metal. A new method to recover the metal from the industrial galvanising dross was proposed using supergravity separation. During the hot-dip galvanising process, the presence of zinc dross has a serious impact on the surface quality of the hot-dip galvanised sheet, forming zinc dross defects. To reduce the impact of zinc dross, the zinc dross on the surface of the zinc pool needs to be manually or mechanically removed at regular intervals. However, during the dross removal process, a large amount of metal zinc is inevitably carried out, resulting in low zinc utilisation rate and high zinc loss rate. This article proposes an efficient and low-cost technology for the recycling and utilisation of hotdip galvanised dross, which uses super-gravity technology to recover hot-dip galvanised dross online. The metal in the hot-dip galvanised dross returns to the zinc pot in situ, while a small part of the dross remains in the super-gravity equipment, which can reduce the amount of zinc dross by more than 60 per cent and achieve a reduction in zinc loss from 17 per cent to less than 7 per cent.

Jun 19, 2024

By D Cliff

"Recent underground coal mine incidents have again raised the issue of: under what circumstanceis it safe for personnel to re-enter the mine? Mine rescue guidelines make recommendations aboutthe limits in terms of the circumstances, lives at risk, no lives at risk and training exercises. Theseare based upon percentages of the upper and lower explosive limits. Many factors infl uencesett ing limits for safe re-entry. These include: the representativeness of the sampling location(s),the rapidity of gett ing an underground sample analysed and the rate of change of the atmospherebeing monitored. Value judgements based upon these parameters will then infl uence the sett ing ofa trigger point based upon per cent explosibility. This raises the question of how the percentage ofthe lower or upper explosive limit is established. It is easy to defi ne this when the sampling pointdata sit on the fresh air limit line. However - what value is used when the sample sits somewherein the body of an explosibility diagram? This paper explores the various options and illustratesvarious pitfalls and problems that are faced in making such a determination. These include howthe data are represented and the assumed knowledge of those doing the interpretation."

Jun 1, 2012

By C W. Davis

Every diesel engine emits approximately 100 million nano diesel particles (nDP) per cubic centimetre of raw exhaust. Each nDP has a diameter of between 50 and 70 nano metres or 1/100th the size of red blood cells (diameter of between 6 and 8 microns). When inhaled, some nDP pass through the lungs and penetrate all body tissue [1]. Europe and North America have recognised and are addressing the long term health problems posed by nano diesel particulate matter (nDPM) across their societies [2.3]. Australia has been slow to recognise the issue, at both a societal and mining industry level. There are chronic health effects for every underground miner and serious legal issues for mining companies with increasingly stringent Occupational Health and Safety legislation being implemented at a state level across Australia. This paper will review progress within Australian society and more particularly the underground hard rock mining industry, particularly in Western Australia (WA).

Mar 15, 2021

By R Zhang, J Xu, X Lv, C Bai, S Zhang

This paper studies the grinding behaviour of vanadium-titanium magnetite concentrate in a ball mill. The grinding kinetics, surface morphology, lattice distortion, wettability and moisture capacity were analysed. Grinding kinetics equation was established based on population balances model with the size distribution data from a laser diffraction technique. The SEM photos of the ground concentrate showed that the surface gets rough with increasing grind time. Agglomeration of fine particles was enhanced when the grinding time reached 30 minutes. X-ray diffraction results showed that a loss in crystalline occurred with increasing the grinding time. The peaks of the X-ray diffraction patterns are significantly broadened with increasing grinding time. Wettability, characterised by contact angle between the material and water, improved due to the fact that the surface roughness increased with increasing grinding time. Moisture capacity of concentrate ascends abruptly in the first three minutes and then changed slowly with increasing grinding time. The water transfer coefficient in the particles increased rapidly in the first six minutes and then decreased quickly until grinding time reached 12 minutes.CITATION:Zhang, R, Lv, X, Bai, C, Xu, J and Zhang, S, 2013. Wet grinding of ?vanadium-titanium magnetite concentrate in a ball mill, in Proceedings Iron Ore 2013 , pp 511-518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Q Yu, G Ren, Z-Y Chen, J Yang

The wedge shape theory of the rock fragmentation range in bench blasting is presented according to the dynamic characteristics of rock fragmentation by blasting in open pit under the condition of hole-by-hole initiation. The finite element software ABAQUS was used to analyse the rock fragmentation mechanism. The rock mass stress contours, crack propagation and damage evolution of different moments were obtained. The results showed that the wedge shape theory of blasting is closer to the rock fragmentation in hole-by-hole blasting and is useful to the design and calculation of charge weight.CITATION:Yang, J, Chen, Z-Y, Yu, Q and Ren, G, 2015. The wedge theory of borehole charge design for bench blasting and its numerical simulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 169–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Melloy, D Holt, M Jurak

Oaky North is AustraliaÆs highest producing underground coal mine. In 2011, the mine produced 8.7 Mt of high-quality coking coal. The high quantities are a result of the constant strive for optimising the operating time of major production units, which involves investing numerous resources, including diesel equipment, in supporting and maintaining their operation.In July 2011 it was identified that the diesel particulate matter (DPM) levels in the underground workings were above acceptable levels, due to the high level of diesel activity. Over the next 12 months, several controls were implemented to reduce exposure to personnel: the main ventilation system was upgraded; the production forecast was adjusted to better manage the diesel fleet, removing surges in diesel usage; and an electronic diesel tag board was introduced to centrally manage the distribution of diesel usage around the mine.From the start of the campaign in emission reduction, an intense DPM monitoring regime was established. Within a few months of the introduction of the centralised tag board, there was a major reduction in emission levels. After the installation and commissioning of the new main fans, the emission levels dropped further, such that over-exposures are now a rarity.Oaky North continues to explore new systems to better utilise their diesel fleet while still maintaining control over DPM emissions.CITATION:Melloy, A, Holt, D and Jurak, M, 2013. Reduction in diesel particulate matter at Oaky North, in Proceedings The Australian Mine Ventilation Conference , pp 187-190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013