Search Documents

By Horrocks KRS, Smitham JB, Ellison JF

This paper describes the development and installation of equipment for continuously measuring separating density in the dense medium cyclone circuits of the four million tpa Port Kembla B/C plant coal washeries. Monitoring equipment consisting of magnetic coils and differential pressure cells were installed in U-tubes taking the full flow of magnetite from the drain sections of the product drain and rinse screens. The monitoring equipment measures overflow magnetics concentration and overflow density continuously and has operated since 1989. From these measurements and calibration trials, the separating density of operating cyclone modules can be inferred reliably. Variographic analyses of the data show that medium density control to +/- 0.002 RD units and separation density control to +/- 0.007 RD units are achievable. Either method for measuring separation density can be used with approximately the same accuracy, although the overflow density measurement technique suffers from the need to have regular flushing of the Dp cells which complicates the signal analysis. Data from the plant shows that separation density can be controlled by regulating medium density, but the assumption of a constant offset between medium density and separation density is erroneous.

Jan 1, 1993

By K M. Watling, F M, G K. Parker

Surface enhanced Raman scattering (SERS) spectroscopy at surfaces under electrochemical control has been applied to elucidate the adsorption of thiol collectors. SERS spectroelectrochemical studies at coinage metal electrodes have been carried out on ethyl xanthate and three iso-xanthates, O-isopropyl-N-ethylthionocarbamate, 2-mercaptobenzothiazole, diisobutyl- dithiophosphinate and butylethoxycarbonylthioura. For each collector, adsorption occurs via charge transfer to form a metal-sulfur bond and, in situations for which the reversible potential of the formation of the bulk phase is known, at underpotentials.

Jan 1, 2005

By T Mahlangu

The leaching of gold in alkaline aqueous cyanide solutions may be reduced significantly by the passivation of the gold by a surface layer of polymeric aurocyanide. This passivation of the gold is typically countered by the presence of Pb(+2) species in solution, which may be present as an impurity in the solution, or specifically added for this purpose. The speciation and availability of Pb(+2) in typical cyanide leach solutions is illustrated as a function of pH, and the presence of S(-2), S(+6), Cu(+1) and Ag(+1) species. The probable role of the Pb(+2) species in efficient gold leaching is discussed.

Jan 1, 2007

By King RP, Kientzler P

In recent years, ultrasonic comminution technology has been developed at the Utah Comminution Center. An ultrasonic grinding device was assembled and investigated. An ultrasonic transducer system has been significantly improved by using a special type of piezoelectric ceramic and preloading to 4.1 x le kPa to obtain maximum strength. The improved system provides constant and rapid vibratory promotion of fatigue fracture resulting in more effective breakage. The design principles for an ultrasonic mill are developed in this paper. Size reduction was successfully achieved in the ultrasonic nip-roll device for a variety of materials. Ultrasonic comminution has repeatedly demonstrated the capability of producing fine particles from a variety of materials. A comparison between ultrasonic grinding and dry ball milling of limestone showed that the ultrasonic device produced much narrower size distributions than the ball mill. This trend is especially obvious in the coarse size range where few particles remain, and in the fine size range where overgrinding is prevented. This behavior might have some interesting applications in areas other than mineral processing like powder metallurgy or material science where narrow and controlled product sizes are required for the successful elaboration of high-technology ceramics and glasses. Ultrasonic comminution has a significant advantage in the accurate control of the product size.

Jan 1, 1993

By Murakami T, Tamiya M, Mizokawa T, Matsumoto T

In the expansion program of the iron ore pelletizing plant at Kakogawa Works of Kobe Steel Ltd., an automatic computer control of products fineness on grinding department is practised. The main problem of the process control of a grinding system is scattering of measured fineness values of products. The scattering comes from the inherent nature of grinding systems, sampled powders and measuring systems. A method is developed to presume the exact status of the plant from scattering products (fineness values and to achieve a stable con trollability of the plant by utilizing the computer. An on-line fineness analyzer, an automatic sampling device and vari-speed air separators are also developed to compose the automatic grinding plant. This report introduces the fundamental epts and results of the automatic fineness rol system of the grinding plant.

Jan 1, 1977

By Mathew P. J

The CSIRO Division of Mineral and Process Engineering in Melbourne has been developing on-stream analysis sensors based on neutron and gamma radiation for better control of quality and process operations. This has resulted in the development of Ironscan, an on-stream analyser that measures the iron content of both lump and fine iron ore on conveyor belts. It can be mounted under existing conveyors with minimal modifications to the conveyor structure and can cope with steel cables in the belt. An interface gauge and an on-stream coal ash analyser have also been developed, both based on measurement of natural radioactivity. The interface gauge monitors the interface between liquor and mud in thickeners and washers, provided the natural radioactivity of the mud is sufficiently high to detect it above background. The natural-gamma ash gauge is a valuable addition to the Coalscan range of ash gauges. It is applicable to heavily laden coal conveyors or bins where the coal bed thickness exceeds 30 cm, and also to lightly laden conveyors, provided the coal is profiled on the conveyor.

Jan 1, 1991

By Scales PJ

Fatigue is the primary cause of failure of structural and mechanical components subject to dynamic loading. Recognition of this basic fact and the development of appropriate techniques and details are important in the design and repair of off highway trucks (OHTs). The frames and appendages of OHTs and other mobile plant used in the Pilbara are subject to tough operating conditions. Any fatigue-prone details quickly show up and become a maintenance liability of considerable concern. Much of this equipment is approaching the limit of its fatigue life and maintenance managers face decisions on whether to repair or replace. Even new equipment often contains some poor details which suffer distress soon after commissioning. In those cases a repair is required which will reinstate the detail to its original intended design life. Repair details must be practical and cost effective. They must also be tailored to the capability and expertise available in the field or in local manufacturers' establishments. This is particularly important where original equipment was manufactured overseas and long delivery times are involved. Lessons are drawn from components which have failed, using the evidence constructively, to provide an upgraded part or an improved substitute. With the experience now available it is relatively easy to extrapolate to cover new problem areas. This paper describes specialised techniques of mechanical fastening and detailing for low fatigue susceptibility, built up over many years of experience with OHTs and other mining plant and equipment in the Pilbara.

Jan 1, 1982

By Baxter D. A

This paper, one of two written about the Queensland Railways Brunswick Street tunnels presented at the VIII Australian Tunnelling Conference, 1993, describes the design and monitoring aspects of the railway tunnels built between Central Station and Brunswick Street Station.The design was mainly influenced by the need to minimise settlement of buildings above the route. The performance of the design details and the monitoring of the tunnels are briefly described.Appendices include extensions to the work of Curtis in the analysis of circular tunnels in a viscoelastic ground.Reference: Asche, H R and Baxter, D A, 1993. Design and ground support monitoring of the Brunwick Street rail tunnels, Brisbane, VIII Australian Tunnelling Conference.

Jan 1, 1993

The light microscopic study of the physical structures of coal and associated mineral matter is an important technique in providing information on the characterisitics and possible behaviour of coals in industrial processes. However the ultrafine nature of coal and mineral particles together with the limits of resolution of the light microscope restrict such studies. Scanning electron microscopy (SEM)with its better resolution and higher magnifications is the means by which further information on coal properties can be obtained. An associated energy dispersive X-ray specrometry (EDS) method allows non-destructive in-situ chemical analyses to be carried out at the same time.

Jan 1, 1989

For many crushed aggregate producers will the finest fraction minus 4 mm represent a problem. The fine material will fetch a much lower price than the coarser products, and may even be difficult to sell in some markets. The blasting operation will strongly influence the generation of fines after both blasting and crushing. Drill hole deviation together with the drill hole diameter, powder factor and velocity of detonation are the most important blasting parameters with regard to the generation of fines. Drill hole deviation is often ignored, and many operators will just reduce the drilling pattern in order to avoid hard bottom and an excessive number of boulders. The paper presents a technical and economic analysis of how drill hole deviation will lead to an increased generation of fines in crushed aggregate production. The analysis shows that the loss of sales revenues will be much higher than the extra costs for drilling and blasting caused by compensating for drill hole deviation by putting in more holes.

Jan 1, 1999

By Dorricott M. G, McAllister J

This paper is concerned with the application of a probabilistic approach to the risk assessment of mining projects.In current practice, sensitivity analysis is the most commonly used deterministic approach of accounting for the uncertainties involved in mining project evaluation, while Monte Carlo simulation is considered to be the best probabilistic method available for the same purpose. The methodology of the approach proposed in this paper is as simple as that of sensitivity analysis. However, the results obtained can be more comprehensive than those obtained from Monte Carlo simulation. Various important statistical features, such as correlation and skewness, of the basic random parameters can be easily taken into account by the proposed approach. Example studies are demonstrated. Lotus 123 was employed for the associated probabilistic calculations.

Jan 1, 1992

By Garrigan J. S, Oakes I

Current operating practice in a plant commissioned some five years ago to treat ferritic zinc plant residue by the "Jarosite" process is described. Major problems overcome include obtaining reliable pH measurements at 100¦C, prevention of scale build up in spent electrolyte heaters, blinding of jarosite filter cloths and the deposition of gypsum in filter presses.

Jan 1, 1977

By Reilly L, Worner H. K

The EnvIRONment process has been developed to treat steel works dust and organic wastes simultaneously. A pelletised feed is fed into a special DC electric furnace, the pellets becoming immersed in a molten slag above a carbon saturated bath. The iron oxide in the pellets is reduced and carburised whilst the organics are broken down to carbon monoxide, carbon dioxide, hydrogen and water vapour. Volatile metals are vapourised and collected in the baghouse. Over two years of trials in a 100 kg DC electric are furnace has brought the process to the stage where it is ready for commercialisation.

Jan 1, 1995

By Hara Y, Arino S, Nakamura M, Tachimori M

The theoretical and experimental studies have been done to clarify the hearth flow of iron and slag. The results of dissections show that the hearth can be treated as a packed bed of coke hav- ing good permeability with a coke-free layer at the bottom of the hearth. 3-dimensional numerical calculations of hearth flow with and without a coke-free layer are carried out, and the results are assured by a water model simulation. The influences of a coke-free layer on the iron flow and the discharge route of iron and slag are examined. The 3-dimensional flow pattern can be represented simply by the travelling time, which depends on characteristically the profile of coke-free layer and the quantity of iron in the hearth. Those flow parameters could be obtained by the results of radioisotope tracer test ( Co for iron flow, and Sc for slag flow) at several furnaces. As a result, it is found that the coke-free layer repeats the cycle of appearance and disappearance at several-month intervals. This cycle corres- ponds to large temperature fluctuation at the bottom of hearth. The relation between iron flow and skull (solidified iron, coke and deposited graphite mixed layer) on the hearth brick was studied by the model experiment and the thermal analysis based on the indications of thermocouples installed in the bottom of the hearth. If a thin coke-free layer is formed on the skull, a fast iron flow is generated in the layer, and melts away the skull. The growth and melting of skull produces the fluctuation of thermal load on a bottom brick, causing brick Damage.

Jan 1, 1981

By T J. Beardsmore, N Wyche, D Flint, T J. Griffin

Western Australia (WA) is currently the world’s largest iron ore producer, and mining of its huge reserves and resources of iron ore has become a critical part of the state’s economy and regional development. Iron ore exports from WA have reached 760 Mt/a, corresponding to shipping more than one Mt per turn-of-the-tide from the state’s ports. The iron ore sector dominates all commodities produced in WA, and in 2016 accounted for 77 per cent of the state’s royalty receipts, 56 per cent of mineral and petroleum exports (by value) and 50 per cent of mining industry employment. Expenditure on exploration for iron ore (including that for resource estimation and conversion to ore reserves) has declined markedly, from its record peak of $1100 M in 2012 to $280 M in 2016, placing it second after gold. Foreign investment has been a key element underpinning development of the iron ore industry from the 1960s until today, and will likely continue to be so into the future.CITATION:Flint, D, Wyche, N, Beardsmore, T J and Griffin, T J, 2017. The importance of iron ore to Western Australia’s economy, in Proceedings Iron Ore 2017, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Ryan CG, Cousens DR, Griffin WL

The proton microprobe is developing into a vital tool in the geosciences, through its high sensitivity for in-situ detection of trace elements in the ppm regime. This paper will describe the instrument at the CSIRO Heavy Ion Analytical Facility at North Ryde, including features crucial to its successful application in the geoscience. Examples of applications in the basic geoscience and mineral industry related research are described briefly. Conditions required for widescale applications in the minerals industry are Discussed.

Jan 1, 1989

Swedish sulphide mining is presented. Dry filling is described. Fill properties with and without cement addings are dis- cussed in relation to various studies in la- boratory and in situ.

Jan 1, 1973

By Weimin F

In the last decade, great strides have been made in the raise boring technique in China. Extensively, the drilling and blasting method has been replaced by the mechanized raising method since 1980. There are now over 3C raise drills operating in more than 20 mines. The diameters for shaft boring varies from 500mm to 2000mm, and to depths up to 90m. Tlis paper mainly describes the performance, mtLin technical achievments and applications of all four kinds of raise drills, and auxiliary equipment. Finally, some recommend- ations for future improvement in the raise boring technique are presented also.

Jan 1, 1987

By Cooper P. G

I he Electrolytic Refining and Smelting Company (ER&S) has oper- ated a copper smelter at Port Kembla, NSW since 1908. The feasibility of modernising the smelter was recently studied and external influences were shown to have a substantial impact on the project economics. Profita- bility is determined by the relative magnitudes of treatment charge income earned from processing raw materials and the operating costs incurred. Treatment charges are usually denominated in U.S. dollars and are deter- mined by market forces in the world copper industry. ER&S is no different from other Australian manufacturing industries in that it must maintain its competitive position by controlling costs. The modernisation project seeks to achieve this through new technology and improved labour Productivity.

Jan 1, 1988

By Hare S. M, Griffin P. T, O&apos

Chalcopyrite ore and converter slag treatment to produce copper concentrates is undertaken at the Copper Concentrator of Mount Isa Mines Limited. This concentrator was commissioned in May 1973, replacing the original No 1 Lead-Zinc Concentrator, for the processing of all chalcopyrite ore coming from Mount Isa Mine.Treatment of chalcopyrite ore at rates of up to 125 000 l/week is described here; the treatment of converter slag is described later.

Jan 1, 1993