Search Documents

By A Van den Bulck, K Verbeken, O Vergote, I Bellemans

Viscosity is one of the most important physicochemical properties during pyrometallurgical operations. In the sub-liquidus regime, an important factor is the presence of suspended solid particles, yet its influence is not well-described in earlier literature, despite the significance of this factor. This project aims to determine the influence of spinel particles (Zn(Al,Fe)2O4) on the rheology of a multiphase synthetic PbO-SiO2-ZnO-Fe2O3-CaO-Al2O3 slag system. Three data sets with a wellcontrolled methodology and three different spinel sizes (small (13 μm), medium (34 μm) and large particles (76 μm)) were published previously, using a custom-built high-temperature rheometer. This study presents an additional data set of slag viscosity measurements, performed using a different apparatus, the Anton Paar FRS 1800, to verify the consistency of the earlier determined viscosity behaviour. Within this data set, no consistent trend could be found between the predicted wt per cent spinel and the relative viscosity. Therefore, additional quenching experiments were conducted to identify the morphology and experimentally determined volume fraction of the spinel particles in the slag. These measurements revealed a difference in spinel size across the samples and corresponding viscosity behaviour, emphasizing the importance of spinel particle size on slag viscosity. Once the spinel size was taken into account, consistent viscosity results (relative apparent viscosity and flow index) were observed across the two devices. This study confirms that, once all parameters affecting slag viscosity are considered, the viscosity behaviour of a heterogeneous slag can be uniquely determined. The resulting optimised slag viscosity models can be used to predict viscosity before processing, addressing relevant phenomena such as slag tapping, slag foaming and copper droplet settlement.

Aug 21, 2024

By M I. Pownceby, M A. Rhamdhani, S Palanisamy, D Fellicia, B Satritama, G A. Brooks, A Ang

Metal production have long been using carbon sources as both reducing agents and energy sources. Consequently, the global extractive metal sector contributes significantly to greenhouse gas emissions, accounting for approximately 9.5 per cent. Hydrogen gas offers as a promising ecofriendly alternative to carbon in metallurgical processes, serving as both a reductant and energy supplier with a by-product being only water vapour. However, the implementation of molecular hydrogen faces certain challenges related to the thermodynamics and kinetics of metal oxide reduction. In addressing these challenges, researchers have explored the application of hydrogen plasma, generated by subjecting molecular hydrogen to high energy to produce atomic, ionic and excited hydrogen species. Hydrogen plasma offers thermodynamic and kinetic advantages over molecular hydrogen and carbon-based reductants, exhibiting lower standard Gibbs free energy of reaction and activation energy. Therefore, hydrogen plasma can produce metal in fewer steps, process any oxide feed and feed size and even be used to refine metals. Despite these advantages, challenges exist in utilising hydrogen plasma in extractive metallurgy, including electricity costs, potential reverse reactions and industrial-scale implementation. This study provides a mini review of prior research on hydrogen plasma for metal oxides reduction, particularly iron oxide, as well as state-of-the-art techniques for its use in extractive metallurgy applications by mentioning several reactor types. Future prospects and scale-up possibilities of the hydrogen plasma in extractive metallurgy will also be presented.

Aug 21, 2024

Risk management has become an essential tool for mining companies to ensure their projects are well-managed and profit expectations are achieved. Risk management has also become a mandatory corporate governance requirement in Australia for publicly listed companies and equally important to attract investors. This paper provides a brief overview of the essential tools needed to implement a practical risk management framework to comply with the internationally recognised ISO 31000:2009 risk management-principles and guidelines from the perspective of small or soon to be producing mining companies. To?successfully?deal with the unknown and to manage the opportunities and risks involved with a mining project requires a clear understanding of the basic risk management principles. These include how to develop a project risk register, how to develop a project risk treatment plan and how to manage and monitor project risks to take full advantage of the opportunities presented.The first step is to identify and fully appreciate the risks that face a mining project. There are many risk identification methods that can be used including checklists, brainstorming and hazard and operability (HAZOP) studies. These often lead to a telephone book full of risks which are near to impossible to manage. A risk library specifically designed?for mining?projects containing no more than 100 risks will cover the major showstoppers, is practical and can be readily implemented and successfully managed.A risk framework also needs to be established which is compatible with the companyÆs structure and objectives. Once each risk has been assessed in regard to consequence and likelihood and the risk control systems are in place they need to be assigned to the responsible manager. The extreme or high risks will require a risk treatment plan to be developed. Risks will change during the life cycle of a mining project. Hence, a reliable monitoring system is also required for compliance.CITATION:Jones, J A, 2012. Mine project risk management, in Proceedings Project Evaluation 2012 , pp 117-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By D Will

RedrossThe Redross orebody averages 1 m wide, has a strike of 50 - 350 m, dips at 55° and has a basalt footwall and an ultramafic hanging wall. The most successful and innovative aspects of mining Redross were:•ore development innovations, 90 per cent of development was split fired with a shanty back profile to enable larger and more productive equipment to be used and resulted in higher development grades, improved project payback time and improved ore recovery;•hand held stoping using a multiple level, bottom up ‘V’ shaped hand held stoping method that allowed mining on multiple levels with hand held productivities between 50 and 90 tonnes per shift;•the use of 1 m cement pillars and 7 m high crown pillars were used to create multiple mining areas that enabled high overall production rates from hand held mining this orebody; and•the use of vertical cement pillars to enable hand held mining of adjacent stopes without leaving ore pillars.MarinersThe Mariners orebody averages 3 m wide, has a strike length of 50 - 250 m and dips at 50° with a basalt footwall and poor ultramafic hanging wall. The most successful innovative ideas of re-opening Mariners were:•Dewatering the existing mine workings utilising ‘oilfield’ technology by installing a long submersible pump in on existing pump rising main. This enabled the mine to be dewatered at rates up to 100l/ sec and helped overcome the 45 to 55 L/s inflows.•Overcoming the technical problems associated with Mining N07 ore blocks which had severely deteriorated from being underwater for five years by using reverse firing techniques to improve extraction rates and reduce dilution.•Mass firing a large mining block in the N08 with minimal void space because of deteriorating ground conditions.•Use of a longhole version of the Redross hand held mining method to achieve 100 per cent extraction of the N09 higher grade lenses.

Mar 21, 2011

By Kuzmitch O, Morozov A

The main direction in the mechanisation in the mines of the Donbas and the USSR is long-face technology with complexes on the base of hydraulic supports. On the base of the 30 year old experience of exploitation of the coal clearing systems the serious data about the behaviour of the contained rock, display of underground pressure 'on longwalls and preparatory workings have been accumulated. Exploitation works in mines of the USSR are carried out at different depths: from 1000m to 1200m. There are 26 mines in Donbas, which exceed the depth of 1000m. It is the mines of Donbas, where is a rich experience of the exploitation of coal seams in various conditions. Besides, there are wide variations on the factors of the extraction thickness, depth of seam, angle of dip, occurrence of gas dynamics and others. In many scientific establishments, and in Donetsk Polytechnical Institute also, there are scientific research/results, which can be of interest for the coal mining countries.The volume of coal mining from longwall system-mechanised walls in Donbas became stable at the end of the 70s at level of 70 percent. All the efforts to increase this level have not given any notable results, not saying about the technical-economical data, which gradually deteriorate. It shows that positive progress in using the technology for the long walls is over and it is necessary to find new ways of mechanisation of coal winning.

Jan 1, 1991

By D Pateman, F de Fredrick

The Bentley underground mine, which is located 60km north of Leonora, Western Australia, is owned and operated by Round Oak Minerals Pty Limited. A high-grade Zn-Cu Volcanogenic Massive Sulphide (VMS) orebody, Bentley was discovered in 2008 with production commencing in 2012. Long-hole open stoping is employed to mine the steeply dipping ore body, and in recent years the Avoca method has been adopted. This requires all development in a particular area of the mine to be completed prior to stoping commencing in a bottom up sequence. Voids are commonly backfilled with loose Run-of-Mine (ROM) waste loose rockfill (LRF); or alternatively cemented rockfill (CRF) can be used. Stopes in the 3860 AOS and 3900 AOS panels were located below previously extracted Avoca zones, with LRF situated immediately above them. These high-grade stopes were originally designed with rib and sill pillars to maintain control of the existing backfill during extraction. Due to changing factors over time, including mining economics, alternative options to achieve full extraction of the stopes were reviewed, including: • Mining small successive full height stopes which would involve drawing a blanket of LRF down with the extracted ore (stoping under waste); • Stabilisation of the existing LRF above the stopes and implementing a primary/secondary stoping sequence, with the primary stopes backfilled using a cement fill. An assessment of these options was undertaken which determined that the second full extraction method was the most beneficial to the operation, and could be achieved using a cement grout (Minova’s FB200 grout) to stabilise the LRF in conjunction with implementing a sequence where the primary stopes would be backfilled with cemented aggregate fill (CAF). Footwall drives were developed adjacent to the rockfilled stopes, allowing for the installation of horizontal grouting conduits, as well as providing access to the top of the planned 3860 and 3900 level stopes for the placement of CAF. An interval at the base of the previously rockfilled stopes was grouted at multiple horizons to achieve the required thickness, with a comprehensive quality assurance/quality control (QA/QC) process undertaken. Primary stopes were CAF backfilled via an arrangement of downhole winzes, linking the top of primary stopes to cross-cuts developed off the associated footwall drives. CAF was delivered underground through an open reticulation network that was extended to the specific levels. Overall the successful implementation of the revised mining method effectively increased ore recovery while maintaining control of overbreak and dilution, providing significant financial upside. This was achieved while maintaining effective controls in light of the changes to the risk profile. Stabilisation of the existing rockfill has allowed the extraction of stopes to full height, including the originally designed sill pillars, representing an average 23% increase in ore tonnes on the initial design, with dilution from the stope crowns averaging less than 1%. The use of CAF in association with primary/secondary stoping, eliminating the need for rib pillars, has yielded an average 47% increase in ore tonnes compared to the base case mine design.

Mar 15, 2021

Teleseismic travel time residuals measured on 600-1000 km seismic arrays across the Rio Grande and East African rifts provide evidence for upper mantle low velocity zones beneath each rift of velocity contrast 6%-8%. Refraction studies show thinning of the crust below the rift axes. Regional uplift which extends hundreds of km either side of the axes, is isostatically compensated by negative density contrast at depth. Since the refraction argues against compensation by thickened crust, compensation in the upper mantle low velocity zones is suggested. Temperature effects alone can not explain the reduced velocities. Generation of a few percent of partial melt is the most probable source of the reduction. A passive extensional mechanism is investigated for the Rio Grande rift in which hot asthenosphere intrudes the lithosphere raising its temperature and generating moderate melting. It requires less than 1% extension to explain the melting but a prodigious 26% to raise the temperature from a pre-rifting continental geotherm to the solidus. Geological estimates find that extension is less than 10% over the uplift zone. Such a mechanism is possible only if the prerifting lower lithosphere geotherm lies closer to the solidus than that of stable continent. This is supported by the observed high heat flow in the Rio Grande rift uplift region which, given the long time constant for thermal diffusion, reflects elevated temperatures at depth well in advance of the onset of rifting.

Jan 1, 1987

By M Randall, P Ebzery, F Burns, C Aisthorpe, P Blanz

SAG Mill process control classically maintains the SAG mill volumetric filling within a set operating range. Typically a SAG mill weight measurement, by either bearing pressure transducers or load cells, is used as an inferred measurement of volumetric filling. To maintain volumetric filling within a set operating range the SAG weight setpoint use for process control requires regular review due to changes in SAG mill charge density (rock:ball ratio) and the wearing of mill liners. At Lihir Gold Mine in Papua New Guinea, the use of SAG mill weight for process control is additionally complicated by compromised load cells and drifting bearing pressure measurements. The need for an improved method of measuring and controlling volumetric filling led to the recent installation of the Outotec MillSense, a SAG mill toe angle instrument. This paper presents the integration of the toe angle control in to the Lihir SAG mill process control philosophy as replacement for the traditional mill weight control.CITATION:Burns, F, Aisthorpe, C, Blanz, P, Randall, M and Ebzery, P, 2018. Toe angle measurement for SAG mill control at Lihir gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 59–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By B Lumsden

During periods of high metal prices and strong metal demand tailings retreatment can be economic. Most tailings retreatment operations are technically challenging, low margin operations, because the easily recovered mineral has already been removed, therefore, process improvements can potentially yield large economic benefits. The Hellyer tailings dam was owned by Intec Ltd and contained 10.9 million tonnes grading 2.8 per cent zinc, 3.0 per cent lead, 88 g/t of silver, 0.16 per cent copper and 2.6 g/t gold. In November 2006 the Polymetals Group, as operator, restarted the Hellyer plant to retreat these tailings. Within a few months the operation had stabilised and Polymetals was meeting budgeted targets of throughput, metal recovery and concentrate quality. Polymetals and Intec then investigated methods that would improve the metallurgical result for this difficult to treat tailings. Since the tailings are fine-grained with 80 per cent <45 ¦m, magnetic aggregation of the paramagnetic sphalerite was evaluated. Magnetic aggregation of an oxidised tailings feed has not been tested before, nor had the technology been available when Hellyer ore was originally processed. Extensive statistical test work showed magnetic aggregation of the sphalerite fines in the zinc cleaner circuit increased total zinc recovery. The increase in the mean zinc recovery with magnetic conditioning was 3.63 per cent, at a statistical level of confidence of 97.8 per cent, and at the same mean zinc concentrate grade.

Jan 1, 2009

By R Dunne, G Lane, S Ha, D Dreisinger

The paper outlines the 17 Mt/a Telfer Project plant process design from sample selection to feasibility study design. The 366 Mt Telfer mine reserve consists of a diverse range of copper and gold mineralisation, from massive sulfide reef ores to stockwork ore, oxide copper minerals to chalcopyrite, siltstone to competent quartzite, all with relatively high levels of gravity recoverable gold. The complexity of the orebody demanded a flexible plant that could recover copper and gold values by a combination of gravity recovery, flotation and concentrate leaching. The demands of treating ore from a high grade underground mine and a variable grade open pit (that includes underground old mine workings) necessitated a dual train approach from primary crushing to concentrate production in order to minimise the requirement for campaigning of different ore types. An extensive sampling, testwork and technical evaluation program was undertaken to identify processing characteristics and the optimum process route for each ore type. The design experience included: the development of robust primary stockpiling and pebble crushing concepts; detailed review of scale-up of SAG and ball mill pilot plant data to plant scale; the selection of two 15 MW SAG mills and two 13 MW ball mills for the grinding circuit; and detailed modelling of the pyrite concentrate carbon-in-leach (CIL)/sulfidisation acidification recovery thickening (SART)/acidification volatilisation recovery (AVR) process to optimise design for copper and cyanide recovery from leach liquors. The Telfer plant design also measures the development of process design based on experiences at the Cadia Hill Cu/Au concentrator, commissioned in 1998. The differences between the two plants are compared and contrasted.

Jan 1, 2003

By A M. Nyembwe, A M. Garbers-Craig, R Cromarty

With the depletion of high-grade lump iron ore, concentrates have been identified as an alternative material for sinter making. Adding concentrates to the sinter mixture reduces sinter bed porosity and gas flow through the sinter bed. This will result in lower sinter strand productivity. A potential solution to this problem is to add concentrate in the form of micropellets. This study investigates the effect of concentrate and micropellet additions on the permeability of the sinter mixture. Permeability was measured on sinter mixtures containing ten to 40 per cent concentrates and micropellets at various moisture contents. The effect of concentrate and micropellet addition on the permeability–moisture relationship was examined. The results confirmed that the addition of concentrates into the sinter mix decreases the maximum permeability of the sinter bed. The incorporation of micropellets into the sinter mix reduced the permeability less than concentrate addition. The study also showed that the maximum permeability of sinter mixes containing concentrate is reached at the same moisture content as the sinter mixture without concentrate addition. For sinter mixes containing micropellets, additional water must be added to obtain maximum permeability. Parameters including the granule size, void fraction and angle of repose were also investigated to evaluate their effects on the sinter bed permeability.CITATION:Nyembwe, A M, Cromarty, R and Garbers-Craig, A M, 2015. Effect of concentrate and micropellet addition on iron ore sinter bed permeability, in Proceedings Iron Ore 2015, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M C. Evans

"Mine decommissioning is the final phase in a mining project. Planning for decommissioning must commence for a proposed mine even before the government approves it. Queensland mining approvals require proponents to commit to completion (or closure) criteria defining successful rehabilitation. Queensland mining project statutory environmental authorities must also specify how progressive rehabilitation is to occur throughout the mining project. Final landforms with graded banks together with creek and run-off diversions are often required and constructed early in the life of a mining project. At closure, mining projects must demonstrate that future medium-term risks are not significant, or failing this, a residual risk financial payment must be made to the state. CSIRO climate change projections indicate that Queensland is likely to become warmer this century with less rainfall in parts and with extreme rainfall events likely to occur more frequently. This project was undertaken to?determine: if current rehabilitation planning tools assist in determining the environmental risks from mining closure not adequately addressing climate change if these risks are addressed by current rehabilitation outcomes.The north-west Queensland mining region and the central Queensland coalfields were represented in this project by five study sites. Local data sets for temperature, rainfall and rainfall intensity were produced using conservative greenhouse gas emission scenarios representing likely future atmospheres, and using the SimCLIM climate model, Evaporation data sets were also derived from available climate parameters. These projected climate variables supported equations and models used in Queensland to determine mining project rehabilitation completion criteria. Storm intensities and return intervals were directly applied to assess the likelihood of failure of engineered structures such as stormwater diversions and banks. Plant cover change determined by an existing growth model together with rainfall intensity and changes in the R and C factors of the universal soil loss equation (USLE) erosion model enabled estimates of long-term erosion rates. Flood estimates were undertaken using regional rated catchments.The study found that stormwater diversions and banks on recontoured rehabilitated landforms, if constructed to currently accepted completion criteria, would likely fail within 30 years and with the likelihood of failure steadily increasing thereafter. The change in likelihood of failure was able to be estimated and could be applied to the determination of residual environmental risk for approval of a surrender application involving rehabilitation. The USLE model showed that long-term erosion rates increased as a consequence of climate change from north to south across the Queensland mining precincts. Because the growth model did not consider carbon dioxide fertilisation affects, results would likely be worse-case.Likely climate change outcomes have consequential residual environmental risks of mining project rehabilitation failure. This increased risk may result in increased payments to the state from mining projects where high consequences exist. The liability to the state and risk to the environment can be avoided if today’s completion criteria address tomorrow’s climate change impacts.CITATION:Evans, M C, 2014. Queensland mines should consider climate change impacts for decommissioning, in Proceedings Life-of-Mine 2014, pp 535–562 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 16, 2014

By A D. Campbell

The sublevel caving (SLC) mining method is becoming more widely adopted as an underground mining method as mines become deeper and target lower grade mineralisation. SLC has been successfully adopted in increasingly complex and wide-ranging conditions in the past 10–20 years, demonstrating the flexibility of the method. Various challenges encountered at SLC mines around the world have led to significant differences in operating practices, mine performance and mine productivity. Unfortunately, aspects related to productivity, operational performance and best practice are not widely published and remain with individual companies. Limited information is publicly available to compare operational performance of SLC mines in the various conditions where the mining method is now being applied. To overcome this shortcoming, a global review of SLC operations was undertaken over a three-year period as part of the Cave Mining 2040 research consortium. The purpose of the review was to document technical and operational practices, hazard management strategies and key benchmarking metrics at SLC mines around the world. A total of 21 mines spread over four continents and 17 different mining companies were included in the project. The main outcome of the project was a manual of operational and technical practices, benchmarking of key metrics and documentation of the current state-of-the-art for each aspect of SLC mining. This paper describes the main findings from the benchmark in terms of mine productivity, including mine development, production and mining costs. The implications of mine scale, depth and ground conditions on operational performance at each of the benchmarked mines is described and charts are provided comparing key productivity metrics.

Mar 29, 2023

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

The Wattle Dam gold mine, located near Kambalda in the Goldfi elds region of Western Australia has recently progressed to an underground operation and is now believed to be Australia's highest grade operating gold mine. At end of March 2010, the deposit had reserves of 132 000 t @ 20.8 g/t for 88 000 oz and by the end of June 2010 had produced 110 000 oz from open-pit and underground mining. The Wattle Dam main lode is characterised by very coarse gold mineralisation. Gold occurs as cm to decimetre fracture fi ll veinlets, shear surface coatings and erratic fl akey clusters. The gold has no quartz or silica association and lacks adjacent low-grade mineralisation or alteration assemblage. Geologically it appears atypical of Archaean lode gold deposits and may represent an extreme end member of the type. Definition of the lode is largely dependent on effective geological identification of the host lode zone and an understanding of the erratic distribution and grade behaviour of a high-nugget, coarse gold deposit. Dependence on assay data to defi ne the lode zone would result in the deposit being mined incorrectly and much of the deposit being left unexploited. This paper discusses the geology, coarse gold characteristics and defi nition methods which are used to successfully defi ne and mine the deposit.

Aug 1, 2010

By W Patton

Investment decisions in the mineral resources sector are made on the basis of an assessment of the economic potential for a mineral deposit. Given the supporting information for the location, scale, and quantity of the commodity of interest, miners and investors aim to make risk-informed decisions when considering further investment. The objective of resource classification is the synthesis of various types and quantities of geologic information used in resource model construction to assign confidence categories to the estimated mineral resources, which can then be used to support informed economic decisions. In this paper a risk-based classification scheme for iron ore mineral resources using conditional simulations is presented. The method involves categorisation of each block according to a confidence level, considering expected recoveries from a kriging model over mining production volumes. The realisations of the simulated model are used to assign risk-based confidence categories to zones of the ore deposit. One motivation for this work is to assess the sensitivity of the scheme to geologic uncertainties. Specifically, that which uncertainty in the layout of mineralising alterations and weathering overprints influence variabilities of associated rock properties and the likelihood of obtaining expected ore recoveries. It is shown these risks have material implications for a project’s economic potential. How the scheme can be extended to the grade control context and the value subsequent grade control activities is also quantified.

May 24, 2023

By JOHN G. RAYNER

An examination was made of the filtration characteristics of a haematite slurry using a range of polyacrylamide based flocculants in solutions containing up to 3 per cent sodium chloride. The polymers used were "high" and "Iow" molecular weight and had from 0 to 40 per cent charged groups.Increasing charge density tends to reduce the dose required to achieve optimum performance measured by filtration rate and by cake moisture. In general increased salt addition tends to increase the dosage required to achieve these optima. Both these observations result from the change in polymer extension and accord well with the bridging theory of flocculation.The dose required for optimal cake moisture is up to three times greater than that required for optimal filtration rate. This effect is reasonably consistent for all polymers studied and appears to be non-linearly dependent on salt concentration, with the difference being small at 0 and 3 per cent but quite significant at 1 per cent.

Jan 1, 1987

By D La Rosa, D Bennett

"Exploration drill core provides for a number of standard measurements essential for determining the viability of a new mine or the extension of an existing one. Rock lithology and alteration can be visually determined and grade measured from the half core. Geotechnical parameters such as rock strength and structure can also be measured. Using suitable proxies, these metrics can then be used to estimate run-of-mine (ROM) particle size. In combination with comminution test results, these can subsequently be used to design comminution circuit configurations and estimate their performance.The Frieda River Project drill core for the large Horse-Ivaal-Trukai copper-gold porphyry deposit was unusual due to a late stage gypsum-anhydrite stockwork event that overprinted much of the deposit. Above the base of the oxidised zone, which closely matches the water table, gypsum and anhydrite has been leached out, effectively removing the glue holding the rock mass together. As a result, much of the rock above this gypsum-anhydrite surface is fragmented and gravel-like in texture, while the material below this horizon is typically uniform and competent.Large volumes of the orebody above the gypsum-anhydrite surface are expected to need minimal or no blasting for efficient excavation. In addition, the fragmented nature of much of the material was expected to reduce comminution specific energy as it already appears as though it has been crushed. While this was expected to have positive impacts to the operation, the lack of standard geological logging methods available to accurately define the degree of in situ fragmentation led to difficulty in gaining certainty over the ROM product and grinding circuit feed size distributions.Using the extensive library of core photos for the project, a novel method using image analysis techniques to take both the intact core and gravel into account to predict ROM fragmentation was developed. In addition, existing point load test data was used to infer the strength of the rock and its impact on the blasting, crushing and grinding processes. The novel approach allowed development of ROM size distribution data and improved certainty in the results of comminution circuit designs.This paper describes the methodology undertaken in detail, and discusses the results obtained.CITATION:Bennett, D and La Rosa, D, 2016. The Frieda River Project – a Novel Approach to Analysing Exploration Drill Core: How Broken is Broken?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By K Jupp, T J. Howard

Cliffs Natural Resources Pty Ltd (CNR) operates iron ore mines in the Koolyanobbing region of Western Australia, about 50 km north of the town of Southern Cross. Ore is trucked from three geographically isolated sources to the crusher at Koolyanobbing, where it is blended before and during crushing. Lump and fines products are produced and railed to Esperance for ship loading and export to Asian customers. CNR is examining alternative processing paths, from mining to ship loading, with the aim of improving efficiency and reducing costs. Modifications to the system must be consistent with potential future expansions and maintain the low inter-shipment grade variability on which CNR prides itself and has built a strong relationship with its customers. In searching for the optimum process design, many options from mine face to ship loading must be evaluated and compared. Pilot plant studies are infeasible, while complex mineralogical interactions, competing goals and numerous possible system configurations limit the applicability of theoretical analysis. It was therefore concluded that simulation modeling would provide the confidence to take the next step into production trials. This paper describes techniques applied at CNR to simulate grade variability resulting from potential process design changes. The simulation models are easily run Excel-based modules, with each module representing a different part of the process. The modules use extensive Visual Basic macros driven by Excel's user-friendly interfaces. Presentation of the results is enhanced by Excel's excellent graphical capabilities. The simulation software stores and graphically presents time-stamped data from a run, enabling detailed analysis of different process configurations. Final success of a simulation run is measured by inter-shipment variability (standard deviation and process capability) and in-process ore tonnages. Meaningful results from the simulations require the initial input data contain the same correlations present in the real production environment, between the mineral components, production linkages and across time. The data also have to allow simulation of potential changes to mining method and introduction of new pits into the blend. Mining data from the real operations under study are therefore used, with average grades and variability adjusted to match potential future development proposals. It is also necessary to filter out medium and long-term variations from the production data as this variability is best controlled through the conventional medium to long-term mine planning process, not by the process design being studied. The filtering was carried out using a Fourier transform technique, which is described.

Jan 1, 2009

By S G. Gemell

"The financial model is an integral component of any project evaluation based on mineral resources, ore reserves and (at least internally) exploration targets. Given the unity of purpose for preparing financial models for project evaluation purposes, the diversity of both format and content of the finalised models is surprising. Many models are prepared by staff or consultants who are comfortable with a particular format that may be used for other purposes, such as budget preparation or financial reporting. It is natural in these situations that the practitioner will take these models and adapt them to the purpose. The end result may or may not succeed in providing a clear, accurate and sufficiently detailed view of the project’s economic viability.When preparing a model, the practitioner should be cognisant of the interpretation and review, or audit, process. The auditor may be a consultant or employee of a bank, potential equity provider or of the project sponsor itself. Depending upon the scale of the project and the level of participation of the entity that the auditor represents, the financial model will be interrogated more or less rigorously. In any event, the end user will require the model to permit easy change of inputs and will wish to confirm that such change is appropriately and thoroughly transmitted throughout.Accordingly, there are some ‘dos and don’ts’ that can be readily applied in the creation of the financial model that will greatly assist the end user, not just in the change of inputs, but also in reviewing the model’s integrity. The less time and effort required by an auditor in this regard is reflected directly in the cost of the review process.CITATION:Gemell, S G, 2016. Financial modelling with the auditor in mind, in Proceedings Project Evaluation 2016, pp 172–180 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016