Search Documents

By H Ishikawa, H Zhou, M Spagnolo, R Halomoan, S Palaniandy

The Karara Mine concentrator commenced operation in November 2012 to produce high-grade magnetite concentrate. The circuit consists of three stages of comminution plus magnetic separation at each stage for early gangue rejection. High-Pressure Grinding Rolls (HPGRs) are used for fine crushing, followed by ball mills and TowerMills in secondary and fine grinding duties respectively. In recent times, the plant throughput rate has had to exceed design by 18% to maintain the targeted concentrate productivity. Meanwhile, the ore hardness has increased by 25% to 15 kWh/t, leading to changes in the circuit operation and design. These changes led to coarser and harder feed to the TowerMill circuit that affects the subsequent separation processes. Nippon Eirich (the TowerMill manufacturer) has partnered with Karara Mining Limited (Karara) to optimise the TowerMill circuit operation to achieve a circuit product with an 80% passing (P80) of 35 µm. Several activities, including a TowerMill circuit audit and performance evaluation, multi-component analysis, modelling and simulation, were carried out as part of the optimisation exercise. The circuit audit results revealed that the TowerMill circuit feed size F80 had increased and ranged from 67–75 µm. The circuit product P80 ranged between 42–55 µm. The average circuit specific energy was 3.4 kWh/t. Moreover, the differences in density between magnetite and gangue minerals had affected the hydrocyclone performance where the efficiency curve exhibits coarse end deflection indicating that low-density coarse material was bypassing to the overflow stream. A multi-component analysis was carried out to further investigate the coarse end deflection of the hydrocyclone efficiency curve. The analysis showed that the magnetite and gangue minerals had different cut sizes of 32 and 64 µm respectively. Furthermore, 33% of the magnetite (below 35 µm) was being recycled back to the mill due to the density effect. Based on these findings, several recommendations for process improvement were identified and implemented including:• converting to a bottom feeding configuration to improve the grinding efficiency in the mill• additional grinding power in the fine grinding duty to compensate for the increase in plant throughput and ore hardness• improved classification efficiency by converting to smaller size hydrocyclones. Simulation studies carried out to evaluate the impact of these implementations had indicated that a P80 close to 35 µm with a steeper size distribution could be achieved by using the bottom feed configuration with additional grinding power. The TowerMill circuit was converted to bottom feed configuration and the performance was evaluated. The operating work index, size specific energy and circulating load were 30% lower than the top feed configuration, indicating that the bottom feed configuration had a higher grinding efficiency. This paper discusses the outcome of the circuit audit, multicomponent analysis, circuit simulations, improvement strategies and quantification of the improvements. CITATION:Palaniandy, S, Spagnolo, M, Halomoan, R, Zhou, H and Ishikawa, H, 2017. Fine grinding circuit process improvement at the Karara mine concentrator, in Proceedings MetPlant 2017, pp 101–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By S Gossmann, J Barlow, S Denner

"Unconventional gas resources, including coal seam gas (CSG) reservoirs, can be located above and below aquifers that provide groundwater for agricultural, industrial, urban and other uses. Development of these resources may, therefore, lead to potential impacts on groundwater supply.Management of reservoir/aquifer interconnections necessitates a program of focused data acquisition. For example, groundwater transfer from shallow aquifers to underlying CSG reservoirs may occur where CSG-containing units subcrop beneath shallow aquifers, possibly at significant distances from operating wells.Arrow Energy is undertaking studies of connectivity between aquifers including an investigation in collaboration with the Queensland Office of Groundwater Impact Assessment to evaluate connectivity between the Condamine Alluvium (CA) and CSG-containing Walloon Coal Measures (WCM).The Condamine Valley hosts highly productive agricultural land with groundwater resources heavily utilised for irrigation. Water demand outstrips available supply and groundwater has been subject to restrictions on further development since the early 1970s. Developments that could have an additional impact on groundwater resources in the CA are of major concern to local landholders. This paper describes: planned field investigations at two sites: 1. Stratheden, where pumping from the WCM will be undertaken 2. Daleglade, where pumping from the CA will occur how the data to be collected from field investigations will be used to refine predictions of flux between the CA and the WCM.CITATION:Denner, S, Gossmann, S and Barlow, J, 2013. Planned field investigation of connectivity between the Condamine Alluvium and Walloon Coal Measures, in Proceedings Water in Mining 2013, pp 91-98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By C Boyle

Brockman 2 mine is located in the Pilbara of Western Australia and is operated by Rio Tinto Iron Ore. Mineralisation is hosted by synclines where there is structural complexity to focus fluid flow. Mineralisation is hosted by the Brockman Iron Formation. Mining is on 10 m benches and blastholes spaced at 6 - 8 m apart are geologically logged, sampled by shovel cuts, and assayed using X-ray fluorescence for ten chemical variables. Blast blocks are digitised by mine geologists to assign destinations of material within blasts. Resource evaluation drilling is on a spacing of 50 m × 50 m across known mineralisation and consists of recent reverse circulation drilling and older open hole percussion drilling. Sampling of resource evaluation drilling is by rotary splitters or riffle splitters, and assaying is by X-ray fluorescence for ten chemical variables. Ordinary kriging of resource evaluation produces a long-term resource model. This study examines whether mine planning would be improved by using a blasthole estimate to extrapolate grades into deeper benches and merging the blasthole estimate with the long-term model made using resource evaluation drilling. The two estimates are merged into one model using an inverse weighting based on kriging variance. However, reconciliation results in a test bench show the original estimate made using resource evaluation drilling more closely matches mine geology block outs than does the merged model. This is due to a local trend of more high grade and higher iron grades of high grade in the area. The blasthole estimate of deeper benches must use extrapolation and it is diffi cult to take local trends into account. In contrast, the estimation using resource evaluation drilling is mainly interpolation and is better able to handle local trends.

Jul 11, 2011

Any Australian who knows of the poverty of the early settlers in the first few years following the arrival of Captain Arthur Phillip with his "first fleet" at Botany Bay must feel proud of the progress that has been made in the 174 years that have elapsed since that momentous occasionGFor all its attractive appearance as reported by Captain Cook and Sir Joseph Banks, the shores of Botany Bay and of Port Jackson proved most ,inhospitable, and the accessible country surrounding them anything but suitable for sustaining the life of the small settlement. It is well known that during the first 15 or 20 years the hardy colonists and un-tfortunate convicts were close to starvation on several occasions and were only saved by the arrival of supply ships, which were dependent on the vagaries of wind and current, and the hazards of the uncharted seas they had to -navigate-.When Australia was little more than a miserable penal settlement, Great Britain was one of the great-powers of the world, and the U,.S.A. was an independent nation with a growing degree of prosperity that even then gave promise of its mighty awakening to become, as it has, a e.olossus of industry and commerce,-and the. leader in living standards of the world to-day.Australia, from such a shaky, and comparatively recent start, has risen to a position in which its living standards rank very high in comparison with those of most of the nations of Europe and America. Exact com-parisons are hard to fix because of the wide variety of factors involved .but the Institute of Pab?Lic Affairs .(Victoria) places Australia fifthin the world, excelled only by the U.S.A., Canada, Sweden and Switzerland. The next best after Australia are the United Kingdom, West Germany and France.How we achieved such a high standard of living is a vast subject for study but some of the economic aspects of our climb from abject poverty to a position of near affluence can readily be identified.

Jan 1, 1962

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By D Yates, C C(te, M Rodgerson

This paper describes how specific technical and regulatory issues related to water management have been dealt with at Anglo AmericanÆs Moranbah North mine. It compiles the collection of practices that have been implemented since 2010 in response to climatic and regulatory drivers. Operations must continually evolve as they face emerging challenges. For Moranbah North mine, one key challenge is the integration of its mine water system to that of its new neighbouring mine Grosvenor. The commitment to ongoing improvement has placed the mine in a good position to face this particular challenge.Water-related risks were identified then mitigated by technical practices, which have focused on improving underground water management, increasing storage capacity and installing a state-of-the-art control system for the management of water on-site and for releases of mine-affected water to the environment. These practices are supported by an extensive monitoring and audit system that provides confidence in the reporting of activities and outcomes. The strategy has helped the operation with its continual attempts to minimise reliance on high-quality third-party water and improving its interaction with the surrounding environment and community.CITATION:Rodgerson, M, Yates, D and C(te, C, 2013. Leading practice water management at Moranbah North Underground Mine, in Proceedings Water in Mining 2013 , pp 301-310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By S Girard, L Rowland, V Lawson, Y Shields

Since 1948, ValeÆs Matte Separation Plant has been successfully using magnetic separation and froth flotation to separate the copper sulfide, nickel sulfide and Ni-Cu metallic alloy contained in Bessemer matte for downstream processing. Though some equipment upgrades have been performed over the years, the flow sheet has generally remained unchanged since the early 1970s. The need to improve metallurgical performance led to the trial of a scalping flotation column to produce a final copper concentrate ahead of the cleaner circuit feed to take advantage of a high degree of copper mineral liberation, reduce cleaner-recleaner circulating loads and decrease the associated loss of selectivity. Plant results indicated that 50 per cent of copper contained in the rougher concentrate could be recovered at final grade target. Results indicate that up to a 1.5 per cent increase in copper recovery to copper concentrate was achieved during the scalper trial due to a reduction in the generation of fine chalcocite which has historically been observed to report to flotation tailings due to surface contamination. Deficiencies are currently being addressed and a long-term trial is scheduled to confirm the benefits of copper scalping.CITATION:Girard, S, Rowland, L, Shields, Y and Lawson, V, 2012. Copper scalping at ValeÆs matte separation plant, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 299-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By T Rohde, P Defferrard

In 2010 a store and release cover (the cover) was constructed on the south waste rock dump (SWRD) at Century mine. This also included aerial seeding of province native trees and shrub seeds. The purpose of the cover is to reduce percolation into the potentially acid-forming (PAF) waste rock by maintaining a compacted reduced permeability layer (RPL) at near-saturated conditions. This is achieved by overlaying the RPL with a 1.5 to 2 m thickness of soil-mulch. The soil-mulch has a hummocky final surface that captures rainfall, so it does not runoff, allowing it in part to infiltrate, with excess water removed by evaporation and transpiration. The RPL is the trafficked surface of the SWRD.The unsaturated behaviour of the cover is being monitored by instrumentation including volumetric water content and matric suction sensors and a weather station capable of estimating evapotranspiration. The instrumentation allows for direct measurement of infiltration into the cover, storage of rainfall, percolation through the base of the cover and in situ soil water characteristic curves (SWCC).The key functions used to describe the unsaturated behaviour of the cover materials is the SWCC and the unsaturated hydraulic conductivity function. The SWCC is a plot of soil water versus soil suction. It provides the loci of moisture states of a soil from the saturated to the dry state.The paper presents the results of five years of monitoring. It shows that total infiltration into the top of the SWRD was about 1.6 – 3.7% of cumulative rainfall over five years, with most of the infiltration going into storage within the cover. Runoff from the top of the dump is not allowed therefore, the remaining 95% of the total rainfall was lost to evaporation or as lateral flow when infiltration reached the RPL. The paper presents some simple analyses of the wetting by rainfall infiltration of the cover, leading to breakthrough at the base. Field data are used to support the analyses.Presentation of the SWRD water balance is also included in the paper using SVFLUX™GE which is a finite element model that simulates water transport through a saturated or unsaturated medium.CITATION:Defferrard, P and Rohde, T, 2018. Five years of cover performance monitoring and modelling for a store and release cover at Century Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 179–189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D Howe

The Athena gold deposit was discovered in 2007 by Gold Fields Australia Ltd, at the St Ives Gold Mine, 35 km southeast of Kambalda, Western Australia. Gold anomalism was identified in sheared Paringa Basalt as a result of a regional scale aircore drilling program, in association with geophysics. In the 18 months following discovery, the deposit was intensely drilled and by June 2009, it was announced that the Athena deposit contained an ore reserve of 1.7 Mt @ 5.6 g/t for 316 koz. This was followed by a feasibility study, and as a result mine development commenced in November 2009.The Athena mineralisation is hosted in a discrete, north-south striking, steep to moderately dipping shear zone within the southwest dipping Paringa Basalt. Vein intensity has a strong correlation to grade and vein type varies from early thin quartz-albite-sulfide (pyrite and/or pyrrhotite) shear parallel veins to strong brecciation and irregular veining with quartz-albite-actinolite-biotite-pyrrhotite infill. The geology preproduction process developed at the Argo mine was refined and improved following a business improvement project. The aim of the process is to construct detailed geological interpretations prior to development allowing informed mining decisions to be made. The process delivers significant cost savings and revenue enhancements.The development of macroscopic classification scheme was critical to determine ore or waste in the early phases of mining. The Style of Deformation, Alteration and Veining (SAV) Code was the result, and has been enhanced as greater geological knowledge is gained over time.

Aug 22, 2011

By O Salisbury

Ingress of air into the longwall goaf environment needs to be managed appropriately to reduce the risk of creating a spontaneous combustion event. The maingate goaf edge is an area of particular concern in this respect, as air often penetrates for some distance into the goaf along this region inbye of the longwall face. Since the flow rate in this part of the goaf is also quite low, an opportunity exists to disrupt the air pathway by implementing a barrier to the airflow. Previous attempts using plugs made from an assortment of materials have resulted in varying degrees of success. More recently, Narrabri Coal Operations (NCO) has introduced the use of a chemical foam that is mixed with nitrogen to produce a standing barrier with the consistency of shaving cream. The implementation of this practice has consistently proven to be very effective for reducing the oxygen concentration along the maingate goaf edge by systematically retreating the foaming unit with the longwall. This paper presents how the foam is applied in the underground goaf environment to prevent oxygen ingress and uses results from gas monitoring to confirm the foam effectiveness.

Oct 12, 2022

By M S. Reston

The Tonkolili banded iron formations (BIF), Sierra Leone, host extensive iron ore deposits which are of economic signifi cance to the seaborne iron ore trade. The deposits are dominated by a strategic JORC compliant mineral resource of 11.6 Bt grading 30.1 per cent Fe comprised of primary magnetite mineralisation in the form of a fresh metamorphosed BIF featuring a uniform mineral assemblage of quartz-magnetite ± ferro-silicate minerals. Pilot plant metallurgical test work has demonstrated that the production of a magnetite concentrate is achievable using the established beneficiation techniques of magnetic separation and flotation. The concentrates arehigh-grade, and suitable for blast furnace or direct reduced iron pellet feed. The major challenge facing the development of such magnetite deposits at industry competitive production rates is the significant capital investment required for process plant and associated infrastructure.Two well-developed weathering zones exist within the deposits, and are associated with the progressive development of a tropical weathering profile overprinting the primary BIF. These zones feature a near surface hard indurated duricrust up to 60 m thick, and a soft progressively developed saprolite between duricrust and fresh BIF. These zones have been found to be amenable to producing iron ore products including DSO lump and sinter fines from the duricrust, and concentrate from the saprolite. Mineral resources sufficient to support commercial production of such iron ore products were defined by an intensive exploration program in 2010.African Minerals Limited has developed a three phase production strategy to progressively self fund the development of the Tonkolili strategic magnetite project by:• commencing a Phase I 12 Mt/a DSO operation in Quarter 4 2011,• increasing production in Phase II to 35 Mt/a with the commissioning of a saprolite beneficitation plant and associated infrastructure upgrades, and• developing a 45 Mt/a Phase III operation producing high-grade magnetite concentrate.The comparatively low capital and operating costs of a duricrust DSO lump and sinter fines operation coupled with its proximity to ground surface make it highly attractive for the generation of early cash flow for the Tonkolili project. Revenue from this early production may be used to selffund the subsequent development of phases requiring progressively more significant beneficiation plant and infrastructure.

Jul 11, 2011

By M Haest

This study demonstrates the application of HyLogging™ technologies for mineralogical characterisation of different iron ore types throughout the Hamersley Province (Western Australia), including a channel iron deposit (Murchison Metals Ltd) and bedded iron deposits in the Brockman and Marra Mamba Iron Formations (BHP Billiton Ltd).Drill core from these deposits was analysed using CSIRO’s hyperspectral drill core logging systems (HyLogging systems), which are commercially available at the AMDEL and AMMTEC laboratories in Perth (Western Australia), through a leasing agreement. These HyLogging systems provide high resolution photographs at 0.1 mm pixel resolution as well as visible and infrared spectroscopic refl ectance data at 1 cm spatial resolution. The minerals identified include haematite, goethite and its subtypes (ie vitreous and ochreous goethite), AlOH-clays (kaolinite, Al-smectite and white mica), carbonates, gibbsite, chlorite, amphibole and hydrated silica as well as water content. The abundance and composition of these minerals was established from the spectral data and was validated against XRF analyses.The full potential of HyLogging systems in the iron ore industry is only starting to be unveiled, but some major benefits have already been demonstrated:• HyLogging systems can delineate different ore zones by mapping the vitreous and ochreous goethites. This has a potentially large impact in mine planning and operations, as hard, vitreous goethite and soft, powdery, ochreous goethite have different processing characteristics that can affect plant throughput if not carefully managed.• HyLogging mineralogy can also be used to support stratigraphic interpretations of the host, for example in subdividing the Dales Gorge 1 - 4 submembers of the Brockman Iron Formation.• HyLogging can have a potentially signifi cant impact on waste rock characterisation, as many of the waste materials can be identifi ed and quantifi ed with hyperspectral data (eg clay-type,• hydration state).• HyLogging can provide accurate three-dimensional (3D) mineralogy to iron ore companies that will empower them to improve future exploration and resource planning.• Application of high resolution photography to further improve ore deposit domaining is also to be considered.

Jul 11, 2011

By C Roche, G M. Mudd

The Morobe Province of central Papua New Guinea (PNG) has been mined for gold for nearly a century, although it is only in the past decade that large-scale modern mining commenced. The Hidden Valley gold-silver project began construction in mid-2006 and production by August 2009, and is located in the mountains above Wau in the headwaters of the Watut River. The mine is owned and operated by the Morobe Mining Joint Venture (MMJV), which also owns the Wafi-Golpu project, comprising the Wafi gold deposit and Golpu copper-gold deposit, situated in the Watut River Valley. Together they represent a potential mine of the scale of Ok Tedi or Bougainville or bigger. The MMJV is owned in equal shares by Newcrest Mining from Australia and Harmony Gold from South Africa. Although Hidden Valley was the first large-scale mine in PNG to engineer and build a tailings storage facility, poor environmental management during construction and early operations led to significant erosion of waste rock and sedimentation impacts throughout the ~200 km length of the Watut River. Since then, substantial efforts have been made to improve environmental management, especially waste rock placement and storage and water quality management. While the impacts from the Hidden Valley project appear to be reducing, the saga has heightened concerns by many along the Watut River and across PNG about ongoing impacts from mining.This paper presents the results of an ongoing project in the Morobe Province conducted by the Mineral Policy Institute examining the historical, current and future impacts of mining, including community views, social and environmental impacts and the monitoring and regulation of mining. Overall, there is a clear need to more fully integrate social and environmental issues into life-of-mine planning and go above and beyond regulatory requirements. In this way, some of the lessons learnt – by the community, MMJV and government – can be incorporated before, during and long after mining.CITATION:Mudd, G M and Roche, C, ?2014. Mining in Morobe, Papua New Guinea – impacts, assurance and self-determination, in Proceedings Life-of-Mine 2014 , pp 313–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

Mining operations in the Obuasi mine of AngloGold Ashanti Limited began in 1897 using mainly gravity concentration and amalgamation to recover the gold from predominantly high-grade quartz ores. The mine is primarily an underground operation, although some surface mining still takes place. Ore is currently processed by two main treatment plants: the Sulfide Treatment Plant (STP) for underground ore and the tailings treatment plant for tailings reclamation operations. STP was commissioned in February 1994 to treat 180 000 t/m of double refractory gold ore and it hosted the then world's largest commercial scale bacterial oxidation plant which uses Gencor's BIOX« technology. Gold is recovered by gravity and flotation, with the regrinding of the sulfide concentrate before bio-oxidation to liberate locked gold in sulfi de minerals. The BIOX« product is leached using the carbon in leach (CIL) process. Gravity gold recovery is a major component of STP operations and its contribution to overall plant recovery is about ten to 13 per cent. Gravity recovery has undergone series of technological upgrading, since the very first circuit which consisted of a Knelson concentrator and a Gemeni shaking table which was incorporated into the milling circuit at the start of the plant. Presently, each of the gravity circuits which consists of Knelson concentrator(s), cyclones and Gekko InLine Reactors (ILR), are located at the Milling and BIOX« circuits. More recently a new gravity recovery facility comprising of four 48 inch Knelson concentrators and cluster of ten inch cyclones have been incorporated at the tail of the flotation circuit. An additional ILR will be commissioned in 2010 to treat the concentrate generated from the new Semi Autogenous Mill #2 (SAG 2) Knelson: concentrator tower under construction. Since the inception of STP, significant gravity recoverable gold has been recovered via Knelson concentrators and the employed circuits have seen a number of modifications and upgrades, motivated by ore mineralogical changes and recovery concerns. The pioneering adoption of the ILR technology in 2001 and 2003 was a critical factor in enhancing the improved recovery benefit of the gravity circuits. Therefore the objective of this paper is to highlight the mine's experience in the gravity recoverable gold process with emphasis on plant modifications and gravity equipment upgrade. Operational challenges and the contribution of gravity gold to overall plant recovery are also discussed.

Aug 1, 2010

By G Fergus, M Hart, S W. Weeks

Rio Tinto Alcan has undertaken feasibility level assessments into the expansion of its bauxite mining operation in an area south of the Embley River in far north Queensland. The project has the potential to extend their Weipa operations by approximately 40 years.The construction and operation of two additional mineral ore processing plants are proposed for the South of Embley project. Golder Associates was engaged to develop and conduct modelling assessments of potential sources of water supply required by mineral ore processing.Two models were developed using GoldSim: a dam yield model and a water balance model. GoldSim is a graphical object-oriented modelling environment with a capacity to carry out dynamic probabilistic simulations. Originally developed by Golder, GoldSim has been applied successfully in a decision support role to a range of mine water management operations.The dam yield model was used to provide estimates of reliability and volume of annual water supply of several potential surface water dams. This information was then used to determine a hierarchy of water supply options for processing plant operations. The water balance model dynamically simulated the water demands of the two production plants and the consequential response in water supply, with respect to the timing and discharges provided by the various source options.Use of the model provided a preliminary operational tool to assist with water supply management decisions. Water quality issues required a blending of water from separate sources and attention paid to scheduling to ensure water supply through the dry season. The model also helped identify risks to water supply in the event of underperformance of one or more water supply sources. This allowed the operational rules to be refined to minimise those risks.The dynamic and stochastic modelling approach provided a method for identification of water supply issues susceptible to seasonal climate variability.CITATION:Weeks, S W, Hart, M and Fergus, G, 2013. A dynamic evaluation of water supply security susceptible to climate seasonality, in Proceedings Water in Mining 2013, pp 197-208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By V Mutton, L Potts, D Joyce

This paper describes the method of extracting sill pillars within the underground operation from under unconsolidated mullock fill at the Cracow Gold Mine. This pillar recovery method was initially successfully used to recover sill pillars at Crusader Mine, Western Australia in 2001. Globally significant resources have been sterilised due to the placement of loose rock fill above crown pillars and within adjacent stopes. The method described here offers significant opportunities to increase recovery of sill pillar recoveries.The royal orebody sill pillars at Cracow Gold Mine form a significant resource. Extraction of these pillars needed to be undertaken with minimal ore dilution and maximum ore recovery. The application that was selected to consolidate the loose mullock fill above each pillar used an injection grouting process (Minova FB200).Cracow Gold Mine mining method is bottom up bench mining. The pillars were left within the orebody to allow for stoping to commence whilst the decline was being developed. Due to the remainder of the orebody being extracted the only access to consolidate the backfill was from the sill pillar extraction level. Numerous problems were encountered and overcome from product selection and trial, system of injection to extraction.This pillar recovery process achieved a 95 per cent recovery of the sill pillar compared with an estimated 60 per cent typical for other mining options.CITATION:Potts, L, Mutton, V and Joyce, D, 2012. Pillar recovery at Cracow gold mine using grouted consolidated mullock, in Proceedings Narrow Vein Mining 2012 , pp 179-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By R P. Varden

This paper looks at the design of the Bentayga raisebore with subsequent back analysis using a LiDAR survey. A search for LiDAR raisebore assessment publications shows little work has been done on this subject. The paper examines the empirical design and RS2 modelling assessment with the bored condition. The high resolution of the LiDAR enabled mapping of weak structures that were located on the geotechnical investigation hole the orientations of which could not be determined. In addition, the scan showed were water ingress was occurring, potential stress overbreak and structural controls on stability. The LiDAR results were able to confirm no additional support work such as a shotcrete liner is necessary. The LiDAR results have been analysed in one metre increments as volume of overbreak against the empirical stability criteria (McCracken & Stacey 1989). The future use of LiDAR mapping over a range of rock mass conditions will provide quantification of the established empirical assessment improving its reliability. It is also a useful and accurate tool to monitor long term stability of a raisebore due to stress change or ore pass due to wear.

Mar 15, 2021

By K Blay, C McCamley, P Petrucci

The Newmont Boddington Gold (NBG) processing plant was designed for 35Mt/y with ball mills expected to deliver a combined new mill feed rate of 4837 tonnes/hr. Since beginning commercial production in late 2009, the plant has steadily increased throughput to meet design capacity in 2014 and reached 37 Mt/y in 2015. Through improved efficiencies, changes to the milling circuit have taken place since commissioning to take the plant beyond its design to an actual throughput of 39.0 Mt in 2017 and a budgeted throughput of 39.4 Mt/y this year.The NBG milling circuit has four parallel ball mills, each consisting of a 7.9 x 13.4 m ball mill with twin 7.5 MW fixed speed motors in closed circuit with twelve 650 mm cyclones. Each mill is fed by two wet screens with the undersize gravitating to a mill discharge hopper where it is combined with the ball mill discharge and pumped to hydrocyclones for classification. The cyclone underflow is re-ground to a target P80 of 150 µm.This paper will focus on process improvements made to the NBG milling circuit which include cyclone reconfiguration, fine screen panel redesign, implementation of an expert control system, mill power draw increase and grinding media changes to take NBG beyond its design throughput.CITATION:McCamley, C, Petrucci, P and Blay, K, 2018. Going beyond design at Newmont Boddington Gold, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 497–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

By G W. Swana

Elastoplastic parameter is a parameter that describe how much materials behave elastically up to certain stress states and plastically thereafter (Hudson and Harrison, 1997). In the continuum analysis, two main parameters of the elastoplastic parameter are modulus elasticity and Poisson’s ratio. In the slope, elastoplastic parameter holds the main role for stability related to deformation in ductile type of rock. There’s a limitation to determine elastic or plastic deformation at the field for ductile rock type. Field manifestation commonly showed that there was no accumulation zone during and after the sliding failure mechanism, in other hand, at the research area, manifestation of deformation at the toe of slope only indicated by bulging shape. This paper will focus at the sliding failure occurred at Coal mining Pit Y owned by Arutmin Indonesia, which according to failure investigation report similar with the condition described above. This paper also will be based on two hypotheses, first hypothesis is claystone rock mass has not been reached plastic deformation yet and the second hypothesis is there is a chance that elastoplastic parameter of the rock mass has been changed during the deformation/sliding failure process. Research method of this paper are back analysis using probabilistic analysis in Finite Element Method (FEM), which conducted before and after failure. Then, the result of the displacement or deformation of the analysis will be checked with the actual deformation shape. Meanwhile, the change of the elastoplastic parameter will be analysed and interpreted. This paper hopefully able to be developed to study about elastoplastic behaviour of rock mass in actual condition and the influence of another uncertainty factor which determine the slope stability.

Nov 29, 2022