Search Documents

By A R. Bye

The mining industry is facing some key challenges that provide a compelling case for geometallurgy initiatives. Over the last 30 years, the average grade of Australian orebodies being mined has halved while the waste removed to access the minerals has more than doubled. In the last eight years, the industry’s energy consumption has increased 70 per cent while multi-factored productivity has fallen 24 per cent. The paper documents a broad range of industry case studies which demonstrate strategies for gaining value from geometallurgy.The mining industry constantly faces the key questions of how significant ore variability is on mine valuation and how would knowledge of the variability change the mining schedule, mine to mill design and operation. Using case studies the paper describes the methods used for incorporating mineral extraction attributes into orebody models and their technical integration into daily operation as well as mine planning optimisation. While pit optimisation from a fully attributed geometallurgical model highlights areas of opportunity and risk it is shown that during the scheduling phase of mine planning that significant value can be added. The benefits from these projects included reducing geotechnical and environmental risk, improving mine to mill performance, option analysis and quantified cash flow risk. There is growing acceptance within the minerals industry that ‘realistically assumed modifying factors’ defined by a competent person/s are not sufficient to mitigate the risk of funding mining ventures. Geometallurgy is moving away from factored ore reserves to data-rich block models providing reliable information for mining, metallurgical and environmental considerations.

Sep 5, 2011

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

The reasons for and the methods of inte- gration of the gold treatment plant with the existing nickel concentrator are discussed. The integration was accomplished in three stages commencing in May 1980 and attain- ing current throughput in December 1982. The problems encountered and their solution, including the design and construction of a new tailings dam are also discussed.

Jan 1, 1984

By B Beale

Bow-tie analysis is a commonly used tool to identify and display risks that have the potential for an undesired hazardous event. The output of the analysis are bow-tie diagrams, which are an effective and versatile communication format that can be applied to any type of risk. Contrary to their simplicity, a proper bow-tie diagram that maintains its usefulness and clear communication is difficult to build. Over two decades assisting Major Hazard Facilities with bow-tie analysis for Safety Cases, several common mistakes have been identified. This paper aims to highlight those issues with examples and provide improvement strategies. A sample of the most common mistakes are: - overly complicated risk analysis - poorly scoped and defined terms - poor descriptions and justifications - identifying too many dependent controls. Overly complicated risk analysis leads to wasted time in obtaining data for little gain. The bow-tie diagram is only a model. Effort should be redirected into identifying and managing controls that will make a tangible difference to site risk. Broad scopes lead to enormous and confusing bow-tie diagrams for both the user and the workshop team. Defining the scope of the study, the consequence severity of interest and critical control characteristics creates focused workshops and targeted analysis. With more definitive scope, there may be more bow-tie diagrams, however, they are succinct and specific. Well described causes are imperative for clear communication to users, regulators and future bowtie review workshop groups. It is best to use common wording structures and explain the event stepby- step. Also, clearly document any likelihood calculations and use data references where applicable. Identifying all possible controls creates a false sense of security that there are many layers of protection. In reality, most controls are dependent on a single system or person and could all be compromised from a single failure. A definition of a ‘bow-tie’ control is required whereby it must be independent from other controls. Improving the bow-tie analysis process will assist operators in developing meaningful and ‘operational’ bow-tie diagrams to support risk management systems and practices.

Apr 16, 2024

By Whitworth N, Anderson P

New plant has been commissioned to treat off-gases from the Fluo-solids Reactor in the Copper Smelter. The new section of plant was built onto an operating system and commissioned with minimum disruption to production. Under construction is a 270 m tall stack for Lead Smelter gases. Additional items for the Lead Smelter will include a new gas cooler, a central baghouse to replace Sinter Plant wet gas scrubbers, a new exhaust fan on the main baghouse, and ducting of drossing gases to the main baghouse. Emphasis is given to discussing improvements the new plant has made to working conditions, the general environment and increased production capability. Total expenditure in the two smelters is in the order of $25 million.

Jan 1, 1978

British Coal's Selby Complex is the newest producing mine in the United Kingdom. The reasons behind its origins, planning and design are explained. Some detail is given of equipment used, with the emphasis being placed on the unique features of its layout. The entire project has been planned and constructed over many years and the design has consequently changed, principally in response to the geology of the coalfield and improving technology. In spite of many totally unexpected difficulties, the mine, which is not yet in full production, has the highest productivity in the United Kingdom.

Jan 1, 1991

By E Claridge

There are a number of major infrastructure tunnelling projects currently underway or proposed in New Zealand, including construction of new road and rail facilities and the refurbishment of existing road tunnels. These new projects have triggered a rethink of traditional practices in underground fire and life safety and local regulation.While there is a current surge in activity, tunnels have been a signifi cant part of New Zealand’s transport infrastructure for over a century. Despite this background, the new projects commonly face challenges that are symptoms of a national regulatory environment that has aspects that are inappropriate for underground environments. There are inconsistencies in local regional regulation and an absence of national guidance and standards relating to tunnel design. Historically, New Zealand has looked across the Tasman for guidance. Although recent overseas tunnel designs present learning opportunities, the adoption of international best practice and standards may not necessarily address local expectations or needs.This paper explores a number of specific matters affecting the design of road and rail tunnels in the New Zealand context, namely; the Building Regulations and associated local consenting processes and parties, and the responsibilities and needs of the New Zealand Fire Service.The discussion highlights the importance of a collaborative approach involving the designer, asset owner, regulators, emergency services, and other parties, and ensuring up-front clarity in design responsibility and ownership of residual risk.

Mar 8, 2011

By D R. Seaman, R P. Tooher, B A. Seaman

"Several mine scheduling tools exist for use in optimising and scheduling the reserve according to in situ value. These tools generally value the ore on a per block basis according to regressed recovery models based on ore grade and type. It is then the task of the plant metallurgist to ensure that these ore blocks are fed to the plant in a manner that satisfies the prevailing plant constraints. This task is often completed in complex Excel® spreadsheets that are modified over time with factors applied to account for plant modifications or limitations.It is the authors’ experience that this approach is difficult to audit and replicate in a consistent manner. Furthermore, operational decisions, such as primary grind size or autoclave oxidation are made on the metallurgist or managements’ perceived optimum value and does not necessarily represent a cash flow based optimum.Many processing plants contain multiple internal constraints. As ore feed grades and properties change over the life-of-mine (LOM), processing-bottlenecks shift from one unit process to another and different operating strategies need to be adopted to maximise cash generation from the process.This paper presents a unified optimisation approach to scheduling ore based on a circuit mass balance to describe the process plant with individual models for each significant unit operation. The approach allows for optimisation over multiple input variables and the inclusion of linear and non-linear constraints.This optimisation process has been applied to different complex gold operations. The end result is an automated scheduler that selects the optimum blend of ores as well as plant operating conditions that satisfy all internal plant and shutdown constraints while maximising the objective of choice (metal production or cash flow). The models are also valuable for evaluating expansion or debottlenecking opportunities of individual processing units. These models are coded in Matlab® R2016a provided by MathWorks®, and can be deployed to end users in a compiled version with significant savings in time to run different scenarios over the Excel®-based systems.Citation:Seaman, D R, Tooher, R P and Seaman, B A, 2016. Optimisation of Complex Gold Processing Plants with Multiple Unit Operation Constraints - the Newcrest Planning Scheduler, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J A. van Niekerk, J G. Jardine, J W. Olivier

The Runruno Gold Project is located on the island of Luzon, approximately 200 miles north of Manilla in the Philippines. The mine is an open cut operation and uses the proven BIOX® and carbon-in-leach (CIL) processes to recover gold, and the ASTER™ process for detoxification of the CIL residue prior to discharge to the Residue Storage Impoundment (RSI). Work to date has defined a mineral resource of 1.39 million ounces (Moz) of gold, and the operation will produce 96 700 oz of gold per annum over a mine life of 10.4 years. The BIOX circuit is designed to treat 140 000 t/y of concentrate with a design capacity of 404 t/d of concentrate at a design sulfide sulfur grade of 17% S2-.The Runruno BIOX Plant is the first application of the Outotec BIOX Generation III design principles, focussing on ease of operation and maintainability. During development and implementation, the project team focussed on identifying opportunities to optimise the capital efficiency while not compromising on the operability or overall efficiency of the process or the equipment. The BIOX plant also incorporates the latest developments in the design of the BIOX agitators for more efficient mixing and gas dispersion. This paper will discuss some of the critical aspects and decisions taken during the development and implementation of the BIOX Process at the Runruno Gold Project. The paper will highlight some of the factors affecting the commissioning process as well as the improvements seen through the introduction of the Generation III BIOX design principles. CITATION:van Niekerk, J A, Olivier, J W and Jardine, J G, 2017. Implementation of the BIOX® process at the Runruno Gold project, in Proceedings MetPlant 2017, pp 218–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By P B. Hills

Almost a quarter of a century since Bridges (1993) documented techniques for the assessment of ground conditions in a seminal paper in the Proceedings Second International Mining Geology Conference, the necessary role of the geologist in recording geotechnical data on exploration properties and in mines remains. Typically, the geologist is the first professional on the exploration property. Of course, most exploration properties don’t become mines. However, when a property does start to come together and form a coherent mineral deposit and professionals from across the minerals industry spectrum, including specialist geotechnical engineers, become increasingly involved, it remains the geologist who has the most intimate knowledge of the deposit. By association, that knowledge extends to the character of the rock mass.Throughout the various phases of prefeasibility, feasibility, construction and production, culminating in the mature mine, the knowledge of the rock mass held by the geologists continues to grow. In the current era of minimising cost and optimising profit, meeting the requirements and expectations of stakeholders ranging from fellow employees to investors, industry and financial regulators and the broader public, in a social environment where occupational health and safety concerns are of uppermost concern in every endeavour, the value of the geologists’ observations cannot be understated. Mines nowadays employ more geotechnical engineers than they did in the early 1990s when Bridges (1993) wrote his paper. More funds are available for specific geotechnical investigations of exploration properties and mines; none-the-less, those programs remain limited in their extent and there is a wealth of additional data available for collection with the appropriate training, at little additional effort. Fundamentally it is all about the numbers. Any hole not geotechnically logged is a hole that will need to be drilled again if the data is required. Any face, surface or underground, not geotechnically mapped is one that may need to be mapped a second time. That doesn’t mean every hole or every face. However, it is the proposition of this paper that the opportunity for additional geotechnical data to be gathered during traditional geological investigations is an opportunity that cannot be ignored. Occupational health and safety requirements demand that the geotechnical risks associated with mining are appropriately managed. Mining regulations in most Australian and overseas jurisdictions requires the consideration of geotechnical risk through formalised management plans. The Joint Ore Reserves Committee (JORC) Code requires the consideration of modifying factors more than ever before. The benefit to be realised through improved geotechnical understanding by geologists on the ground leads to improved occupational health and safety, optimised reporting compliance, and improved financial and social outcomes for the exploration property and ultimately for the mine that follows.CITATION:Hills, P B, 2017. The necessary role of the geologist in geotechnical data gathering, in Proceedings Tenth International Mining Geology Conference 2017, pp 347–354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By C A. Cooper, G A. Suter

The sizing of a starter dam for a Tailings Storage Facility (TSF) involves balancing many competing demands. It should cost as little as possible, be high enough to store tailings until the first raise can be constructed, it must be able to contain water safely, and it must be designed in such a way that the long-term integrity of the higher raises are not compromised, among other things. In addition to these demands there is the complication of the behaviour of the process plant, and the tailings during commissioning. Variations in slurry density, excess water in the TSF, initial settled density of the tailings, reliability issues, and beach slopes above and below water can all impact the way the tailings beaches are developed and ultimately impact the ability of the starter dyke to contain the required volume of tailings and water.The conventional approach to the design of a TSF starter dyke is to begin looking at the elevation required for a set of deterministic design parameters, find ways to reduce the size or volume of it as much as possible to reduce cost, and then possibly look at the sensitivity of some of the input parameters. This paper discusses a stochastic modelling approach for starter dykes that allows a wide range of design inputs to be simulated quickly, with an envelope of possible results produced. The sensitivity to different parameters can also be examined to understand which design inputs have the biggest impact on the required dyke sizing. By integrating the 3D TSF modelling tool Muk3D with GoldSim, it will be demonstrated how a wide range of scenarios can be evaluated and how that information can be used to make better decisions about the selection of design options.CITATION:Cooper, C A and Suter, G A, 2018. Starter dyke optimisation with Muk3D and GoldSim, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 466–475 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Woodhouse M, Andrews D, Drew G

The nickel deposits within the Honeymoon Well project area (26¦ 40'S, 120¦ 25'E), located 45 km south of Wiluna, occur in the northern part of the Agnew-Wiluna belt (Figure 1; Hill et at, 1990). The project area is covered by up to 50 m of transported material which greatly hampers both exploration and an understanding of the bedrock geology. Since 1990 intensive exploration has increased the resource from 10 Mt at one per cent Ni to 134 Mt at 0.76 per cent Ni in five deposits (0.4 per cent Ni cut-off, resources above 300 m depth, December 1994). This includes a massive sulphide resource of 2.5 Mt at 3.4 per cent Ni.

Jan 1, 1996

The Australian Coal Combustion Testing and Research Facility has been operating commercially for one year and during that period coal product evaluations have been conducted on behalf of four coal companies and one electricity commission. The facility is equipped to assess the behaviour of steaming coal in milling, combustion (including flame stability, burnout and heat transfer), ash deposition and erosion, fly ash collection and gaseous emissions. The relevance of the results of the pilot testing to industrial practice was demonstrated during the calibration of the facility using four coals burnt in Australian power stations. The calibration coals were from the Tarong and Gladstone Power Stations in Queensland, tluja Power Station in Western Australia and Bayswater Power Station in New South Wales. Also an opportunity arose to visit an overseas power station to observe a full scale test burn using one of the early coals tested on a commercial basis in the combustion test facility. The calibration trials showed excellent agreement with industrial coal performance in t:orms of flame stability, turndown, carbon burnout and gaseous emissions. Encouraging correlations were also found in the case of furnace radiation, boiler deposits (slagging and fouling) and electrostatic precipitation. In the case of the last group the only real reservations about the correlations are due to the non-availability or qualitative nature of results collected around the power stations. In all cases there is a high degree of confidence in the facility's ability to predict the relative performance of different coals and in some cases direct numerical predictions can be Made.

Jan 1, 1987

By S Q. Liu, E Kozan

This paper proposes a new multiresource multistage scheduling problem for optimising the open pit drilling, blasting and excavating operations under equipment capacity constraints. The flow process is analysed based on the real-life data from an Australian iron ore mine site. The objective of the model is to maximise the throughput and minimise the total idle times of equipment at each stage. The following comprehensive mining attributes and constraints have been considered: types of equipment; operating capacities of equipment; ready times of equipment; speeds of equipment; block-sequence-dependent movement times of equipment; equipment-assignment-dependent operation times of blocks; distances between each pair of blocks; due windows of blocks; material properties of blocks; swell factors of blocks; and slope requirements of blocks. It is formulated by mixed integer programming and solved by ILOG-CPLEX optimiser. The proposed model is validated with extensive computational experiments to improve mine production efficiency at the operational level. The model also provides an intelligent decision support tool to account for the availability and usage of equipment units for drilling, blasting and excavating stages.CITATION:Kozan, E and Liu, S Q, 2014. An Open pit multistage mine production scheduling model for drilling, blasting and excavating operations, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 329–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Longworth C. R

Competing requirements for land usage sometimes make the correct all- ocation difficult. The decision can be complicated by many factors such as local resident pressure, previous government decisions, economic pres- sures and the duration or permanency of the competing land usages. This problem often confronts the extractive industries with consequent delays in granting leases and some- times considerable local dissension. A proposal to extend the high grade silica sand quarry of the Wamberal Sand Company Pty. Limited is a microcosm of these competing requirements. The sand quarry is located on the New South Wales central coast. It is an open pit operation on a near beach deposit of silica sand suitable for flint glass manufacture.

Jan 1, 1976

By Todd S, Lam K, Hewitt A

A series of field experiments investigated the perfonnance of fine mesh curtain screens which were used to suppress coal dust in a transport roadway of a New South Wales colliery. Four types of screens were tested under dry and wet conditions. The screen materials consisted of flyscreen and garden "shadecloth" with single and double membranes of both materials. Personal dust samplers coupled to dust cyclones and filtration cassettes were used to collect the respirable and total components of dusts respectively. The procedure used for locating the samplers upstream and downstream of the screen was based on the roadway air velocity profiles. The number and configuration of the water sprays impinging onto these screens had significant influence on the results. The study showed that wet double layered flyscreen is the most effective of the four configurations tested.

Jan 1, 1991

By T Baumgartl, D R. Mulligan, D Doley, A Schneider

In arid and semi-arid areas evapotranspiration (ET) cover systems are often used to mitigate contaminated seepage from hazardous mine waste into the adjacent environment. The theory of ET covers is based on the water balance equation with the aim of minimising seepage. While cover systems are commonly trialled, the influences of variability in climate and cover structure on water balance equation parameters are seldom investigated.Water balance equation parameters and their variability were analysed for two ET cover trials constructed from benign waste rock in semi-arid Australia. Seasonal and inter-annual variations in rainfall critically influence cover performance. For successful cover system operation, the average return periods for higher than average rainfall should be taken into account. In addition, failure of ET covers has a higher probability in areas with marked rainfall seasonality. Water holding capacity and plant available water content are low in covers constructed from waste rock. Changes in water holding capacity due to variation in particle size distribution are likely and critically influence cover performance. The application of topsoil can be beneficial for water ingress control through run-off, but a balance has to be struck between run-off, erosion and plant available water. Changes in vegetation composition only influence evapotranspiration water losses at plant coverage exceeding 50 per cent, which is unrealistic in semi-arid areas. This study showed that the capacity of ET cover systems to hold and dispose of received rainfall is often lower than assumed by industry practitioners. Furthermore, in order to improve reliability of long term cover performance, the variability of rainfall and water holding capacity of the cover has to be included in water balance models.CITATION:Schneider, A, Baumgartl, T, Doley, D and Mulligan, D R, 2012. Variability in parameters of the water balance equation and their influence on evapotranspiration cover performance, in Proceedings Life-of-Mine 2012 , pp 293-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Parrington PJ, Bailey A

Serious exploration for carbonate-hosted lead/zinc deposits in the Pillara district commenced in 1971 when Trend Exploration acquired exploration tenements covering stream sediment anomalies in the Limestone Billy Hills area. Shell Minerals managed the project from 1974 to 1976, and BHP Minerals Limited assumed management during 1976. Carbonate-hosted 'Mississippi-Valley- type' Pb-Zn deposits most commonly occur in Palaeozoic shallow marine carbonate complexes. At Pillara upper Devonian (Givetian/Frasnian) reef complexes are preserved on the flanks of Precambrian basement 'highs'. Within platform and atoll facies limestones sphalerite-galena- marcasite-calcite mineralisation occurs as disseminations, veins and breccia matrix, mostly associated with fractures and fault zones. Early exploration concentrated on detailed surface geochemistry and IP geophysical surveys, with geological mapping and shallow target percussion and diamond drilling. Results were discouraging and did not indicate potential for a shallow base metal resource. During 1976-77 BHP adopted a grid diamond drilling exploration technique and commenced testing an area of approximately 50 sq. km, initially using an 800 m square grid. In 1978 high grade mineralisation was intersected in an area subsequently named Blendevale. This was in the seventh diamond drill hole in the 800 m grid drilling programme, and to date more than 400 holes have been cored in the Pillara area. Detailed drilling at Blendevale has defined a number of mineralised breccia zones within an area of 2.4 km x 0.5 km, at depths of 100 m to 600 m below surface. The breccia bodies are associated with a series of north-south trending normal fault zones, forming a graben structure. The mineralisation occurs as breccia matrix surrounding unaltered limestone clasts, as veins filling steep fracture zones, and as

Jan 1, 1986

The pilot scale testing of Australian coals for their NO, emissions was carried out at the ACTC to investigate the influence of coal properties, furnace conditions and different NO,, control strategies on NO,, emissions. The NOx emissions for the Australian coals tested were found to vary over a wide range and primarily depended on combustion temperature and excess oxygen conditions. These coals did not exhibit any fundamental difference in NOx levels to other world coals. Under similar combustion conditions, the conversion of coal nitrogen to NO. was found to be best correlated with coal rank parameter, R, max per centage. The use of staged combustion as a control strategy was shown to reduce their NOx levels by 56 - 77 per cent.

Jan 1, 1991

By F Palkovitz, S Wilson, F Felipe

The management of waste from mining operations is a significant aspect of bringing a mineral commodity to final market. The ore beneficiation process and transport/disposal of waste involves significant consumption of costly resources. A number of options exist to dispose of mill waste on surface and as a backfill material. These range in complexity, risk, capital cost, operating cost and ultimately business performance. This paper discusses the value delivered to a business in using dewatering systems including paste as opposed to conventional slurry tailings disposals. This is illustrated through various case studies and serves to demonstrate how paste can add value and reduce risk to a successful business.

Jan 1, 2009