Search Documents

By A Atkins

Six recent case studies were selected based on the eight main causes of mine disasters (Table 1; Quinlan, 2014) and where credible information sources, such as Royal Commission Reports, Coronial Investigations and textbooks, were available. The six case studies are listed below. Details are available via this link or the conference PowerPoint accompanying this paper. 1. Beaconsfield, Tasmania – 2006 Fall of Ground/Seismic Event (Chandler, 2009; Melick, 2007; Wright, 2012). 2. Bingham Canyon, USA – 2013 Manefay Slide (Ross, 2017). 3. Bronzewing, WA – 2000 Hydraulic Fill Inrush (Hope, 2002). 4. Brumadinho and Samarco, Brazil – 2015 and 2019 Tailings Storage Facility (TSF) failures (Bowker, 2019; Darlington et al, 2019; Demajorovic, Lopes and Santiago, 2019; Morgenstern, 2016). 5. Northparkes, NSW – 1999 Cave Air-blast (Bailey, 2003; Hebblewhite, 2003). 6. Pike River, NZ – 2010 Methane Gas Explosion (Macfie, 2013; Panckhurst, Bell and Henry, 2012.

May 5, 2022

DML Resources Limited - Mining Division produced over 50 000 oz of alluvial gold in the 1995 - 1996 year from five operations located in the West Coast and Otago Regions on the South Island of New Zealand. DML Resources Limited - Mining Division have a twenty year history of alluvial gold mining development in New Zealand. Recent expansions have seen the establishment of two operations in Chile whilst exploration continues in Bolivia, Peru and Argentina. The overseas growth is based on a stable production base in New Zealand focussed on the West Coast and Southland/Otago present and future operations. DML Resources consider that the mining potential in the Arahura Valley on the West coast will be fundamental to their New Zealand operations for some time. Collectively the plants operating in this catchment are referred to as the Poutini Project. Recent and late Pleistocene gravels derived from the erosion of the Alpine Schists running parallel to the Alpine Fault located on the Pacific/Australian Plant boundary are thought to be the sources of the alluvial gold in the Arahura and adjacent catchments. These gravels have been extensively mined for the past 130 years yielding some six million ounces over this period. Production from the Poutini Project started in 1989 and stood at approximately 35 000 oz for the 1995 - 1996 year. This production was split among three plants each working different areas of the deposit. Recovery techniques from each of the plants are fundamentally the same. Gravels are fed to a floating treatment plant where, following screening, the gold is recovered using jig plants and knudsen bowls. Overburden to wash stripping ratios vary between zero and seven to one with plants treating between 80 and 250 cubic metres per hour. Restoration of the land following mining is undertaken progressively. All land in the Poutini Project area mined to date has been restored to a standard suitable for dairy farming purposes. The Poutini Project is a cooperative venture between the Maori landowners and DML Resources Ltd. The Arahura River has particular cultural significance to the Maori as it is the source of the much valued greenstone or pounamu a type of jade valued for jewellery and tools. The Poutini Agreement was signed in 1989 setting out the role of each party in the mining of the Arahura and adjacent lands. Current exploration and development should extend the resource to allow mining to continue on the Poutini project for an additional three to five years at current gold prices. Production within new Zealand beyond this point may be compromised by increasing difficulty in gaining access to prospective areas within New Zealand, lowered margins due to high New Zealand dollar exchange rates and the overall lowering of alluvial headgrades throughout the West Coast and Otago/Southland regions. To counter these effects DML has continued to improve on operational efficiency and performance monitoring to optimise the mining practices used. This paper detains the background to the Poutini Project, the geology, plant and equipment used together with descriptions of the current mining methods employed.

Jan 1, 1996

By K B. Quast

Changes in feed size distribution can have significant effects in rod mill grinding. The product sizing resulting from wet batch milling of a tin ore showed little influence on fines production after truncating the feed at either the coarse or fine end. The addition of fine material caused a less amount of fines to be produced and a possible increase in grinding at coarse sizes, although this is complicated by the changing feed size distribution. The changes in feed size distribution caused no tendency for preferential grinding of the cassiterite.

Jan 1, 1998

By K Faure

At Sams Creek a gold-bearing, peralkaline granite pophyry dyke intrudes Ordovician-Silurian metapelite and quartzite. The granite porphyry dyke has a thickness of up to 40 m, extends discontinuously for about 8 km, and intrudes thin lamprophyre dykes along its contacts. The granite dyke and gold-bearing sulphide and quartz-siderite veins within it have been deformed and recrystallised during several phases of folding, the youngest of which is Early Cretaceous.   The unaltered granite porphyry is composed of phenocrysts of perthite, arfvedsonite, aegerine and quartz in a groundmass of the same minerals, with accessory ilmenite, rutile and fluorite. K-Ar dates of amphibole from the granite gave ages of 226 and 246 Ma, but these ages may be a minimum due to resetting during the thermal and deformation events that have affected the area. Unpublished Ar-Ar data on amphibole from the granite show disturbed spectra with high temperature steps around 300-315 Ma, which is consistent with the age of A-type granites in the Buller region. Further age dating of primary and hydrothermal minerals in the granite is continuing. At least three stages of hydrothermal alteration have been identified in the granite. Stage I alteration is characterised by high fO2 magnetite-siderite ¦ biotite, which is cut by thin quartz-pyrite veinlets (Stage II). These are cut by Stage III sulphide, quartz and siderite veins, and pervasive silicification represented by quartz-perthite-albite-rutile ¦ pyrite-siderite-sericite assemblages overprints the earlier alteration stages. Lamprophyre is altered to a siderite-chlorite-sericite assemblage. Stage III sulphide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite ¦ graphite, deposited by low fO2 H2S fluids. The gold contains 18-30 wt% Ag and up to 1 wt% Bi. Temperature of vein formation was estimated from vein quartz fluid inclusion homogenisation temperatures (Th 260-355oC, average 330oC), arsenopyrite-sphalerite thermometry (310-365oC) and quartz-albite stable isotope thermometry (340oC). The altered granite and the veins have been deformed, and recrystallised and competent sulphide minerals are fractured and brecciated. Alteration and mineralisation are confined to the granite porphyry and adjacent lamprophyre.

Jan 1, 2004

Roles of Mineral Impurities and Sulfur in the Leaching Behaviour of Pre-Reduced Ilmenite Ores

Sep 13, 2010

By J P. Sykes, T C. McCuaig, M Jessell, A Trench

The election of Donald Trump and the Brexit referendum herald a shift towards a tighter definition of economic value, at the expense of the broader value concept of sustainable development; as well as a rise of protectionism, reversing a long-term trend of globalisation. However, the situation is complex, especially over the longer term in which mine project development and exploration operates. The minerals sector should proceed with caution. A greater focus on the local impacts of mining may be strategically beneficial, not only to mitigate against a potential protectionist future, but also because sustainable development has become more ‘localist’ via the concept of ‘social licence to operate’, whilst globalisation also seems to provoke increased ‘localist’ sentiments (known as ‘glocalism’). Localist strategies, therefore, seem a good hedge against multiple political futures. By contrast, moving away from sustainable development appears strategically riskier. Not only are ‘unsustainable’ activities, such as pollution and civil rights infringements harder to reverse, but a movement towards a more sustainable global economy may already be predetermined, even if the journey there may seem oblique. It appears that the increased economic development that is coveted globally is intrinsically linked to a rise in environmental and social consciousness.CITATION:Sykes, J P, Trench, A, McCuaig, T C and Jessell, M, 2017. Charles Dickens on the (potentially) changing role of globalisation and sustainability in the long-term future of mining and exploration, in Proceedings Tenth International Mining Geology Conference 2017, pp 239–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Y Zhu, W Liang, P Knights

In recent years, Chinese companies have invested billions in Australian mineral exploration, development and processing. In 2008 - 2009 alone, the Foreign Investment Review Board approved $26.4 B of investment. Much of this investment has been by merger and acquisition (M&A) of Australian resources companies. This paper sets out to investigate how Australian CEOs perceive the cultural and institutional challenges in operating Australia mining companies recently acquired by Chinese interests. HofstedeÆs cultural dimensions and institutional theory from management science were used to develop a structured questionnaire, which was subsequently used to conduct telephone interview of the CEOs of six recently acquired mining companies. Analysis of the survey results indicated that, in all cases, few changes were made to the operational management of the Australian companies post-M&A. The three major benefits for Australian companies as a result of the M&A are the ability to; access long-term debt at lower cost; secure finance for growth plans in financially volatile times; and maintain existing management structures. Some perceived negatives involved longer and more convoluted decision-making as a result of Chinese state approval required for investment decisions. The study identified building æGuanxiÆ and an aversion to losing æfaceÆ as important cultural learnings for Australian CEOs. Maintaining effective communications is regarded as key for successful cultural integration.CITATION:Liang, W, Zhu, Y and Knights, P, 2012. Cultural challenges in Chinese/Australian mining mergers and acquisitions - A CEOÆs perspective, in Proceedings International Mine Management 2012, pp 251-260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By B D. Burford

High intensity stirred milling using the IsaMill has been the enabling technology for many projects by transforming the economics of fine grinding and simplifying circuit design. IsaMill grinding technology was originally developed for large-scale grinding to P80 sizings of 7 ¦m. The IsaMill is a high throughput, high efficiency mill that produces sharp product size distributions in open circuit configuration. The ability to grind in an inert environment, using a wide variety of media types, can give further metallurgical and economic benefits. The high energy intensity results in a small footprint that enhances the ability to distribute grinding power throughout the circuit, applying grinding energy to the minerals that need it. Recent scale up developments in IsaMill technology have enabled the benefits to be extended to large-scale conventional grind sizes, until now the domain of ball and tower mills. This paper will examine the crossover of IsaMill technology from ultrafine applications into the more conventional grinding area (P80 20 - 150 ¦m). Scale-up developments in IsaMill technology that have enabled this are reviewed. The upcoming commissioning of a 3.0 MW M10,000 IsaMill, the most powerful to date, grinding to P80 55 ¦m at PPL in South Africa will be discussed, as will the recent commissioning of a 2.6 MW M10,000 IsaMill at Kumtor. Recent testwork at McArthur River, where an IsaMill is being considered as an addition to the primary grinding circuit to replace the current tower mill will be reviewed. The potential combination of HPGR and IsaMill to transform concentrator grinding economics will also be discussed. Large-scale IsaMill technology has the ability to transform circuit design and energy efficiency for both coarse and fine grinding.

Jan 1, 2006

By H Guthrie, J Hodder, J Bain, S Durkin

Australian mines have traditionally relied on diesel powered vehicles to fulfil their light vehicle needs. There are many reasons for the resources industry to review its use of diesel-powered vehicles. The international industry has developed projects to explore the use of Battery Electric Vehicles (BEV) as a more sustainable alternative to traditional diesel-powered vehicles. While the technology for cost-effectively applying modern high-performance lithium-based batteries to the mining environment has existed for over a decade it is yet to be widespread throughout the industry. Through the collaboration of Safescape, 3ME Technology and Kirkland Lake Gold, with funding from Mining Equipment technology services (METS) Ignited, the project has focussed on advancing the Australian METS sector’s capability in the rapidly approaching implementation of BEV technology. This paper reports on the collaborative approach to develop a prototype vehicle; explains the selection criteria for the various components of the vehicle; and details the risk-based approach to developing a scalable product to replace existing underground light vehicle fleets. The prototype vehicle was tested underground at Kirkland Lake Gold’s Fosterville operations in Victoria beginning in October 2019. Reporting from these trials focusses on the key factors affecting underground operations. These include driveability, safety, charging and cycle times. Gathering data around energy consumption through normal daily duties enabled a model of energy consumption and charging requirements to be developed such that various applications of the electric vehicle can be considered against existing diesel-powered vehicles. This has provided insight into the impact on daily operations, and the way forward for large scale implementation.

Mar 15, 2021

By R Miller, D Hawcroft

The business environment is never still and there has been enormous change in demand, technology and opportunity during the last decade. In order to succeed it is necessary for organisations to change the way work is planned, scheduled and carried out. This is necessary just to survive over time. The success or failure of the business is strongly influenced by people; the way they work, the way they are guided and their feelings about being part of both a team, as well as an organisation. Our Sustainable Integrated Management System (SIMS) philosophy is built on the belief that people want to be constructive and creative and it is their environment and working relationships that influence how their energies are directed.

Jan 1, 2000

Study on Reasonable Mineral Processing Flow Sheet of Yunfu Low-Grade Pyrite Ores Low-grade ores in Yunfu Pyrite Mining Area were investigated, in order to find an economical, reasonable and environment-friendly mineral processing technology, which is of low consumption and high efficiency in pyrite recovering, which can ensure that the quality of pyrite concentrate product is eligible for sale and the sulfur content of the discharged tailings meets the national emission standards. A flow sheet with a classification, a jigging for coarse-grain minerals and a spiral chute separation for fine-grained minerals was adopted, and the sulfur grade and recovery of the pyrite concentrate is 35.50 per cent and 86.70 per cent respectively, while the grade of tailings is only 6.70 per cent.

Sep 13, 2010

By P C. Miclea

Transportation networks extend every day around the world, requiring safe and well-maintained structures for efficiency and for users’ safety. Due to specific features of the infrastructure, such as longer tunnels, increased traffic and marginal safety rules, fire safety in rail and road tunnels becomes more challenging.The situation becomes more critical due to the global economy and increasing worldwide tourism, with multi-national companies often involved in both design and construction of transportation routes or systems in other countries. Tourism brings the risk of visitors becoming victims in a foreign land; thus, international law becomes more and more applicable to transportation projects all over the world, requiring a consistent approach to safety (UN Economic and Social Council, 2001; US DOT Federal Highway Administration (FHWA) 2006; US Transportation Research Board, Committee on the Role of Public Transportation in Emergency Evacuation, 2008; UK Parliamentary Office of Science and Technology, 1997).There are significant differences between rail and road tunnels, both in their functionality and safety requirements. Most tunnels over a certain length are equipped with emergency ventilation systems capable to control the spread of smoke by creating an air stream in the desired direction. Besides ventilation, fire-life safety (FLS) includes smoke and heat detection by linear or spot detectors, closed-circuit television (CCTV) and public address systems with prerecorded announcements, as well as evacuation signage and monitoring capabilities (Vägverket – Swedish National Road Administration, 2004).There isn’t a consistent, worldwide approach to the design of emergency ventilation systems for tunnels, with significant differences from continent to continent (US DOT Federal Highway Administration (FHWA), 2004, US Federal Transit Administration, Transportation Research Board, 2006). In North America US NFPA 130 and 502 standards for rail and road tunnels, respectively, represent the main criteria, however, they are continually revised and new versions issued every three years. For road tunnels the World Road Association PIARC issues guidelines, but they are not truly enforceable. There are no similar international guidelines for rail tunnels, except general recommendations by the International Association of Public Transport (UITP) (IAPT, 2003).In Europe the Directive #54/EC adopted by European Community Parliament in 2004 requires a minimum level of safety for road tunnels users in all existing and proposed tunnels in the Trans-European road network that are greater than 500 m in length. Authorities having jurisdiction in many other individual countries, such as Australia, Austria, Germany, Japan and others, enforce specific safety regulations (Miclea et al, 2007). While it is impossible to summarise all aspects of this topic in a short paper, a review of the design approach, the existing differences in safety requirements, as well as applicable design solutions to meet safety codes for both rail and road tunnels are discussed below.

Mar 8, 2011

By T Muzondo, C Prins, D De Vaux, R Schouwstra

The Mogalakwena Platinum Mine in the northern limb of the Bushveld Complex is Anglo American PlatinumÆs only open cast operation exploiting the Platreef. The Platreef, which extends along the basal contact of the Bushveld Complex, is geologically and mineralogically a much more complex orebody than the Merensky and UG-2 reefs. Changes in the footwall and the genesis of the Platreef translate into a number of rock types being present. These rock types vary in hardness and recovery potential and present challenges to metallurgical staff trying to optimise the concentrator. A true understanding of the implications of treating these rock types is required if the maximum value from this orebody is to be obtained.In order to more accurately forecast production and incorporate ore variation in the mine plan and comminution and flotation circuits, a geometallurgical approach to managing the operation has been used and is being further developed.CITATION:Schouwstra, R, De Vaux, D, Muzondo, T and Prins, C, 2013. A geometallurgical approach at Anglo American PlatinumÆs Mogalakwena Operation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 85-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By S McKnight, L Koroznikova, S Hall

Mineral sands represent an important new resource being developed in the Murray Basin, including parts of western Victoria. This paper will outline a simple methodology for mineral sands characterisation, developed as part of the AMIRA-managed project P777 æThe Development of Heavy Suspension Techniques for High Density Separations (Replacement of ClericiÆs Solution)Æ. This project is currently sponsored by three multinational mining companies (De Beers Consolidated Mines, Iluka Resources Limited and Rio Tinto Limited) and is developing an innovative laboratory mineral characterisation procedure that will allow the replacement of the currently employed highly-toxic chemicals.Mineral sand resources almost always contain more than one valuable (and relatively heavy) mineral. Titanium minerals are found with a large range of titanium contents, giving rise to density variation and often subjective mineralogical descriptions. Companies tend to rely on laboratory heavy liquid separation in the evaluation of samples arising from exploration, mining or metallurgical processes. Unfortunately, there are only a limited number of high density (æheavyÆ) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. However, beyond this value currently only organic liquids can be used. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used; however, this presents significant health and safety hazards. Mixtures of thallium formate and thallium malonate were found in the early 1900s by Clerici to provide liquids having specific gravities between 4.0 and 5.0, hence æClericiÆs solutionÆ. For the characterisation of the heavy components of mineral sand deposits (eg anatase sg 3.9, rutile sg 4.2, ilmenite sg 4.4 û 4.7 and zircon sg 4.6 û 4.8) there is currently no heavy liquid alternative to ClericiÆs solution. ClericiÆs solution is highly toxic and testing is now conducted by very few laboratories worldwide with costs reflecting the chemical costs (though extensive efforts are made to recover and reuse the liquid, plus the requirement of its removal from the mineral samples), the infrastructure costs and health and safety regimes (eg blood testing of exposed staff, inventory management). A simple laboratory technique of density fractionation is being developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions, that can replace ClericiÆs solution in the evaluation of fine mineral sands samples (eg -250+150 microns). The developing methodology that can achieve low-cost, low-toxic separations at relative densities above 5.0 will be outlined and the comparison of results with ClericiÆs solution presented.

Jan 1, 2006

Good morning ladies and gentlemen, and may I thank you for inviting me once again to address your conference. I would first like to welcome you all, especially international delegates and conference speakers. ItÆs a pleasure to be with you all and I hope that you have the time to enjoy the many beautiful sights that the Coromandel and Bay of Plenty have to offer.   Holding your conference in Waihi is particularly apt, especially bearing in mind the conference theme û 'Mining in the Community'. There can be few venues in the world that can boast a world class gold deposit of the likes of Martha Hill located right here in the centre of a rural service town. ItÆs a deposit that has a mining history active now in its third century and that to date has yielded some 7.5 million ounces of gold and 50 million ounces of silver. I doubt that when John McCombie and Robert Lee discovered gold at Martha Hill in 1878 that they had any inkling that their endeavours would be the foundation for a mine that would become such an inseparable part of the economic and social fabric of Waihi for the next 130 years.   This is now my fifth appearance at a New Zealand minerals conference, I especially value such occasions as it allows me to comment on your industryÆs performance over the past year, share my thoughts on matters affecting your industry, and also to give you some feedback from central government.

Jan 1, 2006

Lime and cement manufacturing has a proud history in Otago, with the earliest lime kilns appearing around 1849 at Caversham and Kaikorai in Dunedin . At Dunback or Makareao (to be precise) three well-type kilns were built by the government in 1899. In 1909 these kilns were leased to the then Milburn Lime and Cement Company. They erected a large brick Schmatolla kiln in 1909, elliptical in plan and fired by coal gas. The kiln operated up until 1944 before being left derelict. The quarry which supplied the kiln also supplied the Burnside Cement works from 1929 up until its closure in 1988. The quarry was shifted to the top of the hill in the 1950s.

Jan 1, 1992

A key issue in maintaining the mining industryÆs social contract to access community-owned resources, is the need to be able to demonstrate professional management of resource extraction and the risk associated with mining hazards. Significant failures such as disease relating to coal dust and asbestos and mine disasters such as Moura, Appin and Gretley have resulted in judicial and legislative interventions that respond to the community outcry but do not necessarily effectively manage the longer term risk in a sector driven by new technology. With the implementation of recent amendments to the Queensland Professional Engineers Act, senior engineers in all industries including the mining industry are required to be registered and to demonstrate that they have æmaintained competency in the practice of engineering in the area of engineering for which the (engineer) is ... registeredÆ. This may be facilitated through a report produced by an æAssessing EntityÆ. These entities are approved by the Minister on advice from the Board of Professional Engineers, Queensland. Engineers Australia and The Australasian Institute of Mining and Metallurgy (The AusIMM) are the two professional bodies approved as æassessing entitiesÆ charged with facilitating successful implementation of the process established by the legislation. The scope of the legislation covers engineering enterprises in Queensland and engineering activities elsewhere that may have been designed in Queensland. There is currently a challenge to determine what the necessary health and safety competencies for the mining industry are and how the maintenance of these competencies will be assessed. The different approaches taken by the two assessing entities are compared and contrasted. At the legislative level, establishing an obligation to assess professional competency is simple, but at the level of the profession, it is new ground that warrants a substantial research and development input. The challenge is to develop criteria by which the quality of such system can be assessed. The comparison is made by considering such issues as equity, effectiveness, efficiency, objectiveness and transparency. These five indicators are considered in terms of how they are applied in other sectors and how they might be applied in the mining sector.

Jan 1, 2009

Use of Impact Crushing for the Enrichment of Low-Grade Colemanite Concentrates This paper presents the results of an investigation into the enrichment of -25+3 mm low grade colemanite concentrates exploiting differential breakage properties of various minerals associated within the ore sample. Boric acid production process requires concentrates containing at least 42 per cent B2O3, hence concentrates below this grade either stock piled or further treated to increase B2O3 content. The low grade concentrate is obtained as a by-product of Emet Colemanite Concentrator and the B2O3 content may vary around 37 - 38 per cent. The sample used in the experimental studies assays 37.52 per cent B2O3. In the experimental procedures the sample was crushed using a laboratory size horizontal shaft impact crusher and the products were classified into different size fractions by screening so that any improvement by size could be observed. In the tests the effects of parameters such as the revolution speed of the crusher and heat treatment was checked. Test results prove that boron contents show a tendency to increase as the particle size decreases. As a result of the experimental studies a colemanite concentrate assaying 42.13 per cent B2O3 is produced with 76.55  per cent recovery. Arsenic content is seen to change inversely proportional with the B2O3 content of the concentrate such that it drops from 1016 ppm from the as received sample to 676 ppm in the concentrate.

Sep 13, 2010

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The REFLUX Classifier is used to perform particle separations on the basis of density utilising a set of parallel inclined channels positioned above a vertical fluidised section. In continuous mode, feed enters part way up the vertical section, while fluidisation water is introduced from below. Lower density particles are conveyed upwards and collected in an overflow stream, while high density particles segregate onto the inclined surfaces, settle to the base of the system and empty via an underflow stream. Pressure transducers are used to measure the suspension density in the vertical section. This suspension density is maintained by a pneumatically controlled underflow valve to maintain a target suspension density or ‘set point’.Previously, Galvin et al (2010) demonstrated the significant improvement achieved via a new laminar-shear separation mechanism, achieved by utilising closely spaced inclined channels in the REFLUX Classifier. For the separation of low-density coal particles from mineral matter, a channel spacing of 6 mm proved effective; however, for the separation of gangue minerals from much higher density minerals such as iron ore, the shear-induced lift needs to be even higher. In this paper, we examine the influence of two different channel widths on the continuous processing of an industrial iron ore feed in the REFLUX Classifier. It was found that when moving from 6.0 mm to 3.0 mm channels, the ability of the system to reject coarser gangue material and retain finer high density material across a particle size range from 0.125 to 1.0 mm was increased, resulting in a higher grade product.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2017. Influence of shear rate on separation of iron ore fines using the REFLUXTM Classifier, in Proceedings Iron Ore 2017, pp 205–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J Weir

Accurate sampling of slurry streams is extremely important for metallurgical accounting in mining operations, not only for measuring the ore grade from the mine, but also for measuring the recovery of mineral by the mineral processing plant. Accurate sampling is also required for intermediate streams in complex circuits for determining efficiencies of processing units within the plant. As the profitability of the minerals industry is squeezed more with time, greater emphasis is being placed on efficient use of the resource and accountability of the various sections of the mining operations. This has led to increased awareness and interest in obtaining statistically correct sampling across the operations. Accurate sampling is not only required for metallurgical accounting, but is also required for on-line analysis of the slurry streams for elemental analysis and for particle size. Sampling of slurry streams for metallurgical accounting purposes has traditionally been one of the areas of concern in mineral processing plants. In the first instance, the sampler must be designed to comply with the fundamental principles of sampling theory and must provide a representative sample of the slurry stream. In the second instance, the sampler must continue to reliably provide a representative sample, regardless of wear of the equipment or build up of solids with time and other operating issues. To-date the main type of sampler that has been used in mineral processing plants for metallurgical accounting has been the Cross-Cut sampler. These have a cutter that periodically cuts across the full slurry stream. For large flow slurry streams, these are often followed by a secondary and perhaps a tertiary sampler, to reduce the flow-rate or sample, to a manageable size. This paper discusses a new method of sampling slurry streams that has been developed by Thermo Gamma-Metrics, previously known as Amdel Instrumentation. The new samplers overcome many of the problems associated with cross-cut samplers while providing a sample which is representative of the main stream, throughout the life of the sampling system. The sampler is called the SamStat (Sampling Station) and it is now proven in many applications across many countries and mineral processing plants (PGMs, Cu/Au, Pb/Zn, etc).

Jan 1, 2002