Search Documents

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

Trans. No. Place Date Vol. Page 1. Wilkes-Barre Pa......May.71 1 3 2. Bethlehem, Pa.........Aug., '71 I 10 3. Troy, N.Y............Nov..: 71 1 13 4. Philadelphia, Pa........Feb., 72.. 1 17 5. New York. N. Y.*......May, '72.. 1 20 6. Pittsburgh. Pa.........Oct..' 72.. 1 25 7. Boston, Mesa..........Feb., '73.. 1 28 8. Philadelhia, Pa.*......May, '73.. 2 3 9. Easton, is............Oct..' 73.. 2 7 10. New York, N. Y.......Feb..' 74 . . 2 11 11. St. Louie. Mo.*........May,' 74 . . 3 3 12. Hazleton, Pa...........Oct., '74.. 3 8 13. New Haven Conn......Feb., '75.. 3 15 14. Dover,N.J.*..........May, 75.. 4 3 15. Cleveland,O...........Oct. 75. 4 0 16. Washington D. C......Feb.'' 76.: 4 18 17. philadelphia, Pa.......June,: 76.. 5 3 18. Philadelphia Pa........Oct 76.. 5 19 19. New York, N. Y.......Feb: '77.. 5 27 20. Wilkes-Barre. Pa.*.....Mag :77.. 0 3 21. Amenia N. Y..........Oct. 77.. 6 10 22. Philadeiphia Pa........Feb.;' 78. . 6 18 23. Chattanooga' Term.*. . . May' 78. . 7 3 24. Lake George: N. Y....: Oct. 78. . 7 103 25. Baltimore, Md.*.......Feb:' 79.. 7 217 26. ~ittsburgi, Pa.........~a;' 79.. 6 3 27. Montreal, Canada......~ept.;' 79.. 8 121 28. New York, N. Y.*......Feb., '80.. 8 275 29. Lake Superior, Mich....Aug., '80. . 9 1 30. Philadelphia, Pa.*......Feb., '81. 9 275 31. Staunton, Va..........May, '81. .10 1 32. Harrisburg, Pa.........Oct.. '81..10 119 33. Washington, I). C.*....Feb., '82. . 10 226 34. Denver. Colo..........Aug.. '82. . ll 1 35. Boston. Mass.*.........Feb.. '83..11 217 38. Roanoke, Va...........June, '83.. 12 3 37. Troy, N. Y...........Oct.. '83. .12 175 38. Cincinnati. O.*.... Feb, '84..12 4 39. Chicago Ill............May, '84. . 13 1 40. philadelphia, Pa........Sept., '84. . 13 285 41. New York, N. Y.*......Feb., '85. . 13 586 42. Chattanooga, Tenn.....May, '85..14 1 43. Halifax, N. S..........Sept., '85.. 14 307 44. Pittsburgh, Pa.*........Feb.. '86 . . 14 587 45. Bethlehem. Pa.........May, '86 .. 15 Ixiii. 46. St. Louis, Mo..........Oct, 86.. 15 Ixx. 47. Scranton, Pa.*.........Feb.', '87. . 15 lxxvi 48. Utah and Montana.....July '87.. 16 xvii. 49. Duluth, Minn...........July' '87. -16 xxiv. 50. Boston. Mass.*.........Feb.: '88. . 16 xxviii. 51. Birmingham, Ala.......May, '88. .17 xix. 52. Buffalo N. Y..........Oct. '88.. 17 xxiv. 53. New york, N.Y........feb.' ;89 . . 17 xxxi. 54. Colorado..............June' 89 . . 18 xvii. 55. Ottawa, Canada........Oct., 89. . 18 xxiv. 56. Washington, I). C.*. . . Feb. 90. .18 xxx. 57. New York, N. Y........sept:, '93. .19 vii. 58. New York, N. Y.*......Feb. '91. . 19 xxv. 59. Cleveland, O.......... June, :91 . .a xvi. 60. Glen Summit, Pa.......Oct, 111. . 20 lxi. 61. Baltimore, Md.*.......Feb.: '92. .21 xix. 62. Plattsburg, N. Y.......June, '02. . 21 xxxiii. 03. Reading. Pa...........Oct., :92. .21 xliv. 64. Montreal. Canada*.....Feb. 93..21 65. Chicago, Ill............aug.: '93..22 XI. 66. Virginia Reach. Va.*. ...Feb., '04. .24 xwl. 67. Bridgeport Coon.......Oct., '94..24 xxx?. 08. Florida ...'............Mar., '95. .25 xix 69 Atlanta. Ga......... Oct 95. 25 xi 70. Pittsburgh. Pa.*........Feb., '96.. 26 xvii. Trans. No. Place Date Vol. Page 71. Colorado..............Sept. '96. .26 xxix. 72. Chicago, Ill............Feb.. "97.. 27 xvii. 73. Lake Superior..........July '97. .27 xxx. 74. Atlantic City, N. J.*. ..Feb.: :98. .28 xvii. 75. Buffalo N. Y..........Oct. 08. .28 XXXVI. 76. New York,N. Y.*......Feb.: '99. .29 xvii. 77. California.............Sept., ;99. . 29 xlix. 78. Washington, D. C.*.....Feb., 00. .30 xix. 79. Canada...............Aug.. '00. .30 xlv. 80. Richmond. Va.*........Feb.. '01. . 31 xix. 81. Mexico................Nov..'01.. 32 cxviii. 82. Philadelphia Pa. $......May, :02. . 33 xxxv. 83. New Haven, Conn......Oct.. 02.. 33 xlvii. 84. Albany N. Y.*........Feb '03. .34 xxiii. 85. New York, N. Y........Oct.': '03. .34 xi. 86. Atlantic City. N. J.*....Feb., '04. .35 XXIII. 87. Lake Superior..........Sept.'04. .35 dii. 88. Washington. D. C......May' '05. .36 xlii. 89. British Columbia.......July, '05. . 36 90. Bethlehem. Pa.........Feb. '06. .37 xli. 91. London, England.......July: '06. .37 xlviii. 92. New York, N. Y........April, '07. . 38 lii. 93. Toronto, Canada.......July. '07. .38 lix. 94. New York, N. Y........Feb., :08. .39 xli. 95. Chattanooga, Tenn.....Oct.. 08..39 xlviii. 06. New Haven Conn......Feb. '09. .40 xli. 97. Spokane,Wash.........Sept:.'09. .40 xlviii. 98. Pittsburgh, Pa.........Mar.,'10. .41 xxxviii. 99. Canal Zone............Nov.,'10. .41 dv. 100. Wilkes-Barre, Pa.......June. ' 11. . 42 xxxiv. 101. San Francisco, Cal......Oct.. '11..42 xliv. 102. New York. N. Y.*......Feb 12. .43 Ixxvii. 103. Cleveland, Ohio........0ct;' '12.. 44 wii. 104. New York, N. Y.*......Feb.. '13. .45 xv. 105. Butte, Mont...........Aug., '13. .46 ?' 108. New York, N. Y........Oct., 13..47 vii 107. New York. N. Y.*......Feb.. '14..48 xv. 108 Salt Lake City. Otah Aug. :l. 49 5: 109. Pittsburgh, Pa.........Oct., 14. .50 vii. 110. New York, N. Y.*......Feb., '15. .51 xvi. 111. San Francisco, Cal......Sept., '15. .52 xii. 112. New York,N. Y.*......Feb., '16..54 xvi. 1 Arizona...............Sept.,'l6. .55 VII 114. New York, N. Y.*......Feb., '17: .56 vii. 115. St. Louis, Mo..........Oct.. '17..57 vii. 116. NewYork,N. Y.*......Feb.. '18..59 xvii 117. Colorado.....:........Sept.,'18. .60 vii. 118. Milwaukee, Wis........Oct.. '18. .60 x:!: 119. NewYork,N. Y.*......Feb., '19..61 xi. 120. Chicago...............Sept.,' l9.. 62 VII. 121. New York, N. T.*......Feb., '20..63 ix. 122. Lake Superior District. .Aug., '20.. 66 ix. 123. New York, N. Y.*......Feb., '21. .66 xiii. 124. Wilkes-Barre, Pa...... Sept.. : 21.. 66 xix. 125. New York, N. Y.*......Feb., 22. .67 ix. 126. San Francisco. Cal......Sept.,:22. .68 xxix. 127. New York, N.Y.*.....Feb., 23. .69 xxix 128. Canada...............Aug., '23. .69 xxxv! 128.129. New York, N. Y.*......Feb., ;24. .70 xxxi. 130. Birmingham, Ala.......Oct. 24. .71 xxxiii 131. NewYork.N Y.*......Feb.: '25.. 71 xxxviii. 132. 131.Salt Lake City, Utah .. .Sept., '25. .73 xvi 133. New York, N. Y.*......Feb., '26. .73 xxii. 134. Pittsburgh Pa ....... Oct.. '26. .74 xv. 135. New York,' N. Y.*............Feb., '27. .75 x::: 135.136. NewYork,N. Y.*......Feb., '28..76 104 137 NewYork.N. Y.*......Feb., '29. .291 116 138.San FranciscoYork,N.Y. Cal..........Oct. 29..308 406 139. New York, N. Y.*...Feb., '30..30H 1321

Jan 1, 1930

By J. B. Morrow

BITUMINOUS COAL production for 1937 up to Nov. 27, was 400,000,000 ions, an increase of 3.43 per cent over the comparative period in 1936. The in- crease in consumption, however, was not so great as the increase in production. Stocks of coal, mostly in the hands of consumers, on Nov. 1 were 57,000,000 tons, compared to 44,400,000 tons at the same periods in 1936. The prospects were that both production and consumption for December, 1937, would be lower than for the corresponding month of 1936. , Anthracite production for the period ending Nov. 20 was 43,900,000 tons, com- pared to 48,500,000 tons for the corresponding period in 1936, or a decrease of 9.5 per cent. Production of mechanically loaded coal in. 1936 was approximately 57,000,000 tons, an increase of 17.5 per cent over

Jan 1, 1938

By P. G. Meikle, C. T. Holland

The effect of the condition of friction upon the ultimate unit compressive strength as determined between the compressed faces of precisely machined coal specimens and specially prepared testing platens has been examined. Reductions of 30 to 40% in the ultimate unit compressive strength of these model coal pillars have been verified when lubricants areused between the faces as compared to non-lubricated faces. Increase in unit compressive strength due to confinement at each of three levels of friction appears to follow generally the widely accepted "1/2 power law", i.e. S - C (L/T)1/2 where S is the unit ultimate strength, C is a constant dependent on the coal being tested and the coefficient of friction acting at the compression surfaces and L and T are the least width and thickness of the specimen, respectively. Results suggest that the surface condition of both the specimen and platens should be mentioned in detail in conjunction with compression testing, for although the term (L/T)1/2 is adequate for all practical purposes, the coefficient C is directly dependent on the condition of interfacial friction, all else remaining constant. One phase of the investigation of the confining effect of friction on the ultimate unit compressive strength of small coal specimens has recently been completed at the School of Mines of West Virginia University. The efficient control of ground is of fundamental importance to successful mining operations and the design of support pillars has always presented the mining engineer with a difficult and intriguing engineering problem. Since about the turn of the century, many investigators have performed extensive laboratory tests on small coal specimens in efforts to solve some of the perplexing problems of strata control and pillar action in coal mines. A detailed review of this work would serve no purpose here, but a brief mention of the more significant contributions is in order. Muller16 was perhaps the first to illustrate the effect of confining pressure on the strength of coal specimens in compression. His work has recently been more carefully expanded by the experiments of Murrell17 in Great Britain. Rice and Enzian l9 observed that as the size of cubical test specimens increased, the unit compressive strength decreased. These observations were later supplemented by Lawall and Holland, 13 by Greenwald4,5 et a1 at the U. S. Bureau of Mines, by Gaddy3 as well as by Steart,22 Millard15 et a1 and Evans2 et al. Gaddy3 seems to have been first to quantify this relationship with his equation: S = K/vd , where S - ultimate unit compressive strength (psi), K = a constant dependent on the coal, and D =edge dimension (in inches). Holland7 concluded that the strength of coal as affected by lateral dimensions and thickness could be expressed as where K = a coefficient dependent upon the coal, L = least width of pillar (in.) and T = thickness of pillar (in.). Data supplied by this formula have been compared to the estimated stresses in pillars that had been standing for long periods in coal mines and in the cases so far studied the results indicate that the formula predictions are sufficiently accurate for engineering purposes (Holland11 ). This equation therefore is believed to be the simplest and most accurate tool available at the present time for approximating the strength of a coal pillar (over a specified range of L/T) in situ. However, Holland7,9 has indicated that friction between the coal pillars and the top and bottom rock

Jan 1, 1965

By K. A. Natarajan, S. C. Riemer, I. Iwasaki

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration (nitrogen, air, and oxygen) on ball wear was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. Marked ball grinding tests and electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen toward wear (corrosive wear) is relatively small, and abrasive wear appears to be significant. Rheological properties of the slurry appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1985

By Stewart, J. B.

THE property at which this work was done consists of a large deposit of potash salts occurring in massive beds of rock salt, overlain by 600 ft. of salt-impregnated shales and marls. It is in the Province of Cataluiia, Spain, about 45 miles from the railway station of Mauresa and about a mile south of Suria. In addition to sinking the shaft, the program of construction work laid out by the European owners (not Spaniards) included a single-track narrow-gage railroad from Mauresa to the mine; one large office building and several large shop buildings, all of brick and concrete with steel truss roofs; two extensive benches for the future recovery plant; and a large village of stone dwellings for employees. The pay-roll showed approximately 1200 to 1500 men employed. After two years' operation, ending early in the autumn of 1920, the shaft had been sunk 325 ft. and still had an equal distance to go to reach the potash; all tunnels for the railroad were done and the road-bed $0 per cent completed; only a little more than the foundations were completed for all the large buildings, and the excavations of the benches were about 75 per cent done-while only a fair start had been made upon the employees' village. This was the state of affairs when the European owners decided to offer this property under a one-year option to an American syndicate, providing that they agreed to carry on the entire building program and to sink the shaft as fast as was consistent with the quality of work which they demanded, for they wished the shaft to endure at least 200 years.

Jan 1, 1926

By B. A. Kulp, R. R. Reeber

Lattice parameters for the wurtzite form of' CdS mere measured by powder X-ray diffraction techniques over the temperature range 26° to 1000 K'. A negative thermal -expansion coefficient was determined parallel and perpendicular to the c axis below 13.5°K. Near 808°K, the curves of the a, parameter, the differential thermal expansion, and the resistivitv vs absolute temperature exhibited a reversible discontinuity. j\. direct determination of the lattice parameters of CdS over an extended temperature range is of particular use in interpretation of the effects of high pressure on the band structure of semiconductor materials. For example, Langer' has studied the effects of pressure on the absorption edge of CdS from 77°K to room temperature. In order to properly interpret his results it is necessary to know the change in lattice constants as a function of temperature for the wurtzite, zincblende, and rocksalt2 modifications of this material. Thermal-expansion measurements for CdS, wurtzite phase, have previously been determined over a limited temperature range.s74'5 The zincblende phases, of other compounds with similar bonding, have been investigated by Novikova et a! .'' Previous thermal-expansion measurements for metals with hexagonal symmetry have for the most part used bulk sample techniques for low-temperature result. Most X-ray measurements at low temperature have been on materials with cubic symmetry.'jQ The use of X-ray powder-diffraction techniques offers a convenient and accurate method of measurement over a wide temperature range. The X-ray method, besides measuring unit cell size, also provides information about change in structure type and the nature of some of the stacking defects present. I) EXPERIMENTAL PROCEDURE The thermal expansion was measured by X-ray powder-diffraction techniques. Lattice parameters for the range 300" to 1000°K were determined in a 19-cm Unicam camera. From 26" to 300°K a 34-cm back-reflection camera with the Van Arkel" film arrangement was used. The sample was bonded to a copper cold finger below a helium, hydrogen, nitrogen, oxygen, dry ice, or ice brine bath in a metal cryistat. che inner bath was surrounded by another one for radiation shielding. Nitrogen was used in this outer bath for the very low-temperature runs while dry ice and acetone was used for the 195°K point. CuKa X-rays, filtered with a nickel foil, entered the cryostat through a 0.001-in.-thick aluminum window. During a typical 9-hr exposure the sample was continuously rotated through a 30-deg arc. Heat losses from the sample holder limited the minimum temperature attained to 26°K with helium in the inner dewar. Temperature calibration between 25" and 125°K was determined with an Allen Bradley 300-ohm carbon resistor. The resistor was attached to the back of the copper finger with a thin layer of silicone grease. Liquid He, HZ, N2, and O2 baths were used to calibrate the resistor. Temperature variation is estimated to be *2"K with a slightly higher uncertainty at room temperature and 264°K. The thermal expansion of high-purity germanium from 373" to 900°K was measured as a calibration for the Unicam camera. This value was compared with the known value1' for the thermal expansion. A discontinuity in the thermal-expansion coefficient of the CdS a, parameter was observed. Similar discontinuities in the resistivity and differential thermal analysis at the same absolute temperature indicate that the temperature error is *5°K in the temperature range above 500°K. Temperature errors in the Unicam camera below 500°K are appreciably higher due to large gradients in the resistance furnace. II) SAMPLE PREPARATION The CdS was Eagle Picher ultrapure grade. The crystallite size range of the as-received powder

Jan 1, 1965

By R. E. Allen

ONE of the most unusual oil field engineering accomplishments of the past two years is the development and rapid advance in the directed drilling of wells. Directed drilling as referred to herein is the controlled steering of the drill stem in the required direction to a given location in the oil sand. The deliberate drifting of holes is an act so far removed from what has been considered good drilling practice that all of the old questions of correlation, drillability and production difficulties are revived. Only a few years ago, during the boom days of Seminole and Santa Fe Springs, the crooked-hole problem, as it was then called, occupied a primary position among the topics of the day in the fields of California and the Mid-Continent. The net result of all the discussion and study at that time was the conclusion that oil wells should be drilled with as little deviation from

Jan 1, 1933

By J. B. Coher, M. B. Bever

COLD work destroys long-range order, as was first observed by Dehlinger and Graf.1 Dahl2 showed that the mechanical disordering caused by cold work produces changes in those properties that are affected by long-range order. The existence of order has a marked effect on tile manner in which an alloy deforms and therefore on its mechanical properties.L' The relation between order and deformation behavior however, is only beginning to be understood. Seemann and G1ander4 suggested that cold work reduces an ordered alloy to a kind of gruel of antiphase domains. According to Cottrell,5 superdis-locations and pairs of dislocations in a slip plane connected by a strip of anti-phase domain boundary provide deformation mechanisms which do not change the state of order. In general, however, slip may be expected to produce new domain boundaries and destroy order if dislocations move on intersecting planes or cut through existing domain boundaries. The yield strength of an ordered alloy may pass through a maximum with decreasing domain size.5"7 The reduction of domain size resulting from cold work may, therefore, lead to a maximum in strength properties. Flinn8 suggests that dislocations can climb by short-range diffusion during deformation and thus can generate domain boundaries not only on slip planes, but also on other planes which will be those with the lowest domain-boundary energy. It has long been known that the rate of strain hardening of an alloy in the ordered state is larger than in the disordered state.3'9 Also the slip bands in ordered CU3, AU10 and Ni3Mn" are finer than in the disordered alloys. The stress which causes initial yielding in Cu,Au passes through a maximum with decreasing domain size.6'12 A maximum has also been observed in the hardness of ordered Ni3Mn as a function of strain.' These observations suggest, but do not prove, that domain size reduction occurs during deformation. According to Fisher13 slip destroys short-range order and thus the strength of an alloy is related to the degree of short-range order present. Rudman and Averbach14 and Averbach et a1.,15 demonstrated that cold work reduces short-range order in copper-gold and gold-silver alloys. Destruction of long-range and short-range order by cold work implies slip on an appreciable fraction of planes. Yielding of an alloy in which short-range order exists or antiphase domain boundaries are present should be discontinuous because the first dislocations moving across the slip plane meet with the largest resistance.5 Such discontinuous yielding has been observed in CU3AU6,16 and Cuzn.l7 This phenomenon, however, can also be explained by mechanisms not involving order.b The published investigations of the effects of cold work on alloys with long-range or short-range order have not been covered thoroughly in reviews of order-disorder phenomena. These investigations, therefore, will be listed here. They have been concerned with strength properties> 2,3,6,8,9,12,16-21 electrical resistivity,2,4,18,19,21-26: thermoelectric power, magnetic properties,2,18,21,26 and X-ray strain'1,2,14,15,27,28 The slip systems and the appearance of the microstructure after deformation in ordered and disordered alloys have also been investigated. 6.10.ll,l7,23,29,30 The alloys used in these investigations were copper-gold. 1-4,6,9,10,14,16,18 23-26,28,29 copper-zinc. L7. 19. 20,30 nickel-manganese,2 11,21 iron-aluminum. iron-nickel,' copper palladium,4,18,22 gold-silver.4,18,22 and palladium-silver-copper.4 In the work reported here. the changes in properties of polycrystalline Cu3Au were investigated as functions of strain in wire drawing and rolling. Specimens were heat treated before deformation

Jan 1, 1961

By L. E. PORTNER

INCREASING military demands on the petroleum industry have brought into bold relief the crude-oil reserves now available to meet combined military and civilian demands, emphasizing the necessity for a greater efficiency in recovery from what has been discovered than ever before, particularly in light of the absence of new discoveries. This situation-and the fact that the industry, as well as members of the Government charged with governing oil production, desire to meet all crude-oil demands made of the industry with the least loss in tangible reserves through production practices-paves the way for increasing application of sound principles of production engineering and conservation.

Jan 1, 1944

By O. D. Sherby, J. E. Dorn

SEVERAL years ago Zener and Hollomon1 suggested that the flow stress of metals might be related to the temperature and strain rate in accord with the functional equation: s=s(eeh/rt) [1] at the same state. The Zener-Hollomon relation also contains the significant tacit implication that the energy for activation, AH, is substantially independent of the state of the material. The utility of this method for correlating creep data with tensile data was illustrated in a preliminary reportL on the effect of alloying additions on the secondary creep rates of binary a solid solutions in aluminum as shown for Al-Mg alloys in Fig. 1. Not only do the secondary creep and ultimate tensile properties for each alloy correlate well on this plot but in addition the activation energy, AH = 17,900 R cal per mol. is identical for the various compositions. Similar types of curves correlating the secondary creep rates at 422°K (300°F) with ultimate tensile data were also obtained for a series of dilute a solid solutions of copper, germanium, zinc, and silver in aluminum. In all cases the activation energy for creep, AH, was found to be equal to about 17,900 R cal per mol independent of the type of alloying element or its concentration. The coincidence of the activation energies for these alloys is probably due to the fact that the activation energies for creep are rather insensitive to small composition changes. Alloying additions, as shown in Fig. 1, however, increased the stress necessary to obtain equivalent values of ee?H/RT. Thus the stress level in curves of the type represented by Fig. 1 gives the relative creep strengths of the various alloys. Inasmuch as these correlations between creep and tensile data were obtained for creep tests at 422°K, it appeared advisable to ascertain the range of secondary creep rates and temperatures over which correlations between creep and tensile data could be made on the basis of the Zener-Hollomon relationship. If, for example, the activation energy changes with different ranges of creep temperatures, the utility of the proposed analysis would be severely weakened. But if AH is constant not only for all dilute alloys, but also over wide ranges of temperature and secondary creep rates, confidence will be developed not only in the broad utility of the Zener- Table I. Chemical Analysis':' and Grain Size of Alloys Mean Grain Residual Impurities. Wt Pct Diam- Alloying Atomic-eter, Element Pct Si Fe Cu Mg Mn mm Aluminum 99.987 0.003 0.003 0.006 0.001 0.25 Magnesium 1.617 0.003 0.004 0.006 0.26 Copper 0.101 0.003 0.003 0.0006 0.001 0.29 Zinc 1.616 0.003 0.005 0.007 0.001 '0.26 * The authors express their appreciation to the Aluminum Company of America for the preparation and chemical analyses of these alloys. Hollomon relationship, but also in its theoretical justification. The following investigation was instituted in order to ascertain the range of validity of the Zener-Hollomon relationship when it is applied to creep and tension data. Materials, Equipment, Technique In view of rather extensive correlatable data now available on the plastic properties of a series of binary a solid solutions of magnesium, copper, germanium, zinc, and silver in aluminum, these alloys were again selected for the present investigation. Previous reports have already covered the tensile properties of these alloys at subatmospheric temperatures," and at elevated temperature," as well as their fatigue properties at atmospheric temperatures, nd their creep properties at 422°K.' Resistivity measurementsa as well as precision lattice constant determinations? evealed that these alloys are a solid solutions. After homogenization. 0.100 in. thick sheets were rolled to 0.070 in. in thickness and recrystallized to about the same grain size. Since the details of these treatments were reported previously," they will not be repeated here. In order to appropriately reduce the scope of creep tests in this investigation only the typical alloys shown in Table I were investigated. All creep specimens were machined such that their tensile axes were in the rolling direction of the 0.070 in. sheet stock. The gage section was 2 in. long and 0.500 in. wide with a reduced section of 3.50 in. Creep strains were measured by means of rack and pinion type extensometers with a sensitivity of 0.005 in. per division. Readings were estimated to 1/10 of

Jan 1, 1953

By J. E. Tobey

NATIONAL DEFENSE should not create a dilemma in coal utilization such as obtained during the World War. Even under the heavy pressure of a total preparedness program there should be a smooth flow of the right coals from mines to plants. The more than 100,000 industrial plants of the nation must he served with coal of such characteristics and qualities for their individual requirements that no loss of production due to coal failure shall occur. This problem challenges the ingenuity and cooperativeness of producers. transportation executives, consumers and engineers.

Jan 1, 1941

By Ernest N. Patty

WHEN an Alaskan prospector makes a new mineral discovery he stakes out his claims and then starts prospecting for a near-by landing field. This may be a convenient lake but more often it is a gravel bar along a river, where, by cutting off some brush and throwing the larger rocks to one side and then tying a flour sack to a pole, he may decoy some intrepid aviator into testing it gingerly with the wheels of his plane. It was only a few years ago that .the fence around the baseball park at Fairbanks, Alaska, was taken down so that planes could get in and out of the ball park without ripping off boards. Today the grandstand is lost among the modern hangars which line one side of a modern and busy airport. Planes come and go all during the day, and in summer, when there is no darkness, the night stillness is frequently broken by the hum of a motor overhead. Fairbanks is the hub of interior Alaska and from that hub airplanes radiate in all directions to mining camps large and small. An air industry of comparable size is based at the town of Anchorage, and in fact there are but few towns of more than 200 population in the Territory that do not have one or more planes based there.

Jan 1, 1937

By AIME AIME

OVER-ALL operations of the oil industry, as measured by production of crude oil and consumption of products, are almost exactly of the same magnitude as a year ago. Does this mean that the great oil industry has been undisturbed by the war? Has this industry, so vital to the prosecution of the war and to the maintenance of our way of life, been unaffected in its operations? No indeed - changes within the industry are great. It has been called upon to revamp its trans¬portation methods so as to move about one fourth of the total amount of crude and refined products by railroad tank car instead of by ocean-going tankers. Its fundamental internal economy, based on maximum gasoline yield from a barrel of crude, has been relegated to memories of the past. Rationing of oil products, which has been forced upon us in face of an abundant supply, is not only disagreeable medicine but is in itself completely disruptive to the marketing end of the-business.-

Jan 1, 1942

By Dean S. Rogers

The conventional role of exploration, development and grade control is examined in this paper within the context of the many and varied types of gold occurrences which are found at the Dome Mine. The account endeavours to trace the development of the total ore evaluation process, from diamond drilling through the exploration and drifting stage, to the stope development and planning phase of the operation, with an emphasis on sampling techniques and assaying procedure. The concept of ore reserve calculations is developed and the practice of grade control is described. In summary, the role of the geological, the engineering and the mining department is presented in relation to the contribution each has to make in the evaluation and exploitation of ore from one of the world's classic Archean gold deposits.

Jan 1, 1985

By Irwin H. Cornell

BRIEFLY stated, the history of the St. Joseph Lead Co. is the story of how a group of men, working for ten years as officers without salaries and stockholders without dividends, developed a small mine in Missouri into what became a large and prosperous corporation. Their courage and faith in the scattered surface deposits of lead coupled with the management's engineering vision and sound financial judgment should prove an inspiration to present-day mining operators and investors. In 1717, John Law's company, known as "The Company of the West," was formed in France and letters patent were granted, for a period of 25 years by Louis XV, for exploration in the Mississippi River Valley. One of the underlying purposes of the expedition, headed by Mr. Renault and Mr. La Motte, a French metallurgist, was development of the lead mines in the area now known as Southeast Missouri.

Jan 1, 1947

By Peter K. Strangway

During 1973, a 20,000 net ton (18 100 metric ton) formcoke test was carried out at Inland's 26.5-foot (8.08-meter) hearth diameter on NO. 5 Blast Furnace. The formcoke briquettes were produced from Elko1 coal by FMC at their pilot plant in Kemmerer, Wyoming. The briquettes were shipped to Inland in open railroad cars and most of them were placed in an outside storage field until a sufficient amount was available for the actual blast furnace test. The test consisted of three phases: an initial four-week base period; the actual 33-day formcoke test period; and a final three-week post-test base period. During the formcoke test period, the regular coke skip loads were gradually replaced with skips of formcoke until, after a three-week period, the replacement ratio reached 80%. The furnace operated smoothly and quality hot metal was produced. The burden remained permeable and it was possible to maintain wind rates 9 of over 100,000 scfm (47 Nm3/s) without significant blast pressure increases. Dusting from the formcoke was not a problem either in the stockhouse or in the top gas. The formcoke briquettes maintained their original shape and density as they descended through the furnace. When the 80 percent replacement level had been reached, the inwall temperatures became higher than normal (about 2000 ºF (1090 ºC)) and followed an unusual steady pattern. In addition, the top gas temperature became higher than normal, and the hot metal analyses and temperatures began to fluctuate unacceptably. In general, it is felt that the high inwall temperatures were a result of channeling of the hot furnace gases along the stack walls. This channeling appears to have been promoted by a change in distribution of the burden in the top of the furnace which, undoubtedly, was caused by the increased increments of formcoke. Since it was felt to be unsafe to operate the furnace for an extended period of time with the inwall temperatures at the high level, a decision was made to remove the formcoke from the furnace. When this was done, the inwall temperatures returned to normal. Once the inwall temperatures had returned to normal, the remaining 3,800 net tons (3450 metric tons) of formcoke were used in the furnace at a nominal 40% replacement level for five continuous days. The furnace operated smoothly during this period, and the results were representative of satisfactory furnace operation with partial replacement of regular coke with formcoke. The test was successful in proving that formcoke can replace up to about 50% of the regular coke in a large furnace operating at high wind rates. However, additional work will be required to develop acceptable charging practices for using higher levels of formcoke replacement.

Jan 1, 1977

By AIME AIME

S ULFURIC acid made in the United States during the last four years has averaged approximately 7,000,000 tons of 50" B6 acid a year. This is double the production of the year 1913. About 66 per cent of the acid is made from sulfur, 16 per cent from pyrite, 13 per cent at copper, lead, and zinc smelters, and the remainder from miscellaneous sources it her the chamber process or the contact process, (at some plants both) is used. In 1923, the contact process accounted for nearly 30 per cent of all the sulfuric acid made in this country and since then it has been increasingly employed. It was first introduced here in 1898, and has always .proved less expensive than the chamber process for the manufacture of .acid of high concentration and purity, but the latter produces acid of low strength suitable for many industries.

Jan 1, 1929

By W. E. Wrather

CURTAILMENT of production was a matter of far more serious concern to the oil industry through 1933 than the search for new supplies of oil. The huge reserves of crude, built up during past years, instead of inspiring a feeling of security, were viewed apprehensively. The status of past laws and court decisions seemed to guarantee to operators the right to produce oil at will, and this entrenched privilege was so widely adhered to that the market was-in a constant state of chaos. The more modern idea of the ownership of oil in place and correlative rights gained headway slowly, since usually there were enough belligerent producers, staunch believers in the old established order, to defeat the efforts of the majority who sought to' introduce order and restraint. State regulatory commissions were unable to cope, with the rebellion among producers with the result that those who abided by proration rulings were penalized, while those who flouted the rulings and produced unrestrainedly were able to make profits on large volumes of flush oil even at low prices. This situation, known in the vernacular as the "hot 'oil" problem, became so acute that the industry was threatened with ruin. The low price for 36c A.P.I. in the Mid-Continent came in April. at 25c per barrel 'but gradually moved upward to the long-hoped for price of $1.00 per barrel in October, after the Federal Government had taken a hand in the matter and effectively allocated production among the oil producing states and materially curbed the "hot oil" runs.

Jan 1, 1934

By B. C. Craft

Oil and gas development in Mississippi during the year 1933 was rather active and a number of important wildcat wells were drilled throughout the state. Mississippi showed an increase in drilling operations during 1933. There were 58 completions from 22 counties during this period, compared with 53 completions in 10 counties during 1932. The Jackson gas field in Hinds and Rankin counties continued to be the most active area with 26 completions, resulting in 17 gas wells, 2 oil wells, and 7 dry holes, compared with 38 gas wells, 1 oil well and 5 dry holes during 1932. A further attempt to extend the producing limits of the Amory gas field resulted in a dry hole. Extensive exploration in south Mississippi has proved the existence of ample source beds and presence of an extensive sandbody near the top of Cockfield. Core tests, supplemented by extensive geophysical work, have been carried on in Jackson, George, Harrison, Pearl River and Stone counties. Exploration will be continued in 1934. The most important deep test drilled in 1933, and the deepest well ever drilled in a southeastern state, was the Eastman Gardner et al., Bank of Seminary No. 1, sec. 26-8N.-15W., Covington County. This well went through about 1300 ft. of Selma chalk, and was abandoned in the Eutaw at 8004 ft. Another interesting operation during the past year was the Foster Creek Oil Corporation's Foster Creek Lumber Co. No. 1, sec. 14-2N.-2W., in the "Eastern Conroe Trend." This test is shut down at 3687 ft. in the Catahoula sandstone and has not encountered any important shows of oil or gas. A total of 107 of the 117 gas wells completed in the Jackson gas field since its discovery in 1930 are still producing, and have a combined open flow of approximately 3,724,896,000 cu. ft. It is reasonable to assume that this area will be rather inactive during 1934 as the maximum daily production during 1933 was 3,476,000 cu. ft. The 10 wells that have gone dead were edge wells. The water level is now between the sub-sea depths of 2190 and 2195 ft. The Gulf Refining Company's Rainey No. 1, sec. 13-5N.-lE., one of the early wells in the field, had gas and water at —2225 ft. That the field is under hydraulic control is

Jan 1, 1934