Search Documents

By David C. Oyler

The Bureau of Mines conducted research at the 9-Right Section of the Olga Mine to determine the cause of bumps and aid in the development of appropriate control techniques. The purpose of this paper is to identify the factors which affect the occurrence of bumps at the Olga Mine. These factors have been broken down into two categories, in situ and mining related. The in situ factors include those conditions which exist prior to mining, such as variations in lithology and overburden, presence of jointing, the composition and the physical properties of the rock, and the original stress field existing in the coalbed and adjacent strata. The mining factors include the mining sequence, changes in stress in the coalbed and adjacent strata during mining, rates of convergence, and the pattern of failure of the coal and adjacent strata. The factors which appeared to have the greatest effect on bumping were the overburden, the lithology of the roof and floor rock and the physical properties of the rock. The roof rock is generally a massive, stiff sandstone which does not break until coal pillar extraction is complete. The immediate floor is a strong shale which generally grades into siltstone and then into sandstone. The overburden at 9-Right ranged from 990 to 1,600 ft. Secondary factors appeared to be the in situ (pre-mining) stress and the mining sequence. When barrier pillars were split., pressures measured in hydraulic cells (Borehole platen flatjacks) located in those barriers showed large pressure increases, and the incidence of bumps increased, especially when the barriers were near old gob areas. The pillar extraction system used at Olga, where three rows of pillars are mined concurrently, appears to reduce pillar loads at the face areas, thereby reducing the exposure of men and equipment to the risks of bumps during mining operations. The horizontal components of in situ stresses at Olga were found to be nearly the same as those at 5 other mines in southern WV, where humps were not common, so it appears that horizontal in situ stress alone is not a major influence on bumping at the Olga Mine.

Jan 1, 1987

By Barry Voight

The law [ ] where [ ] is a measurable quantity such as strain and A and cu are empirical constants, describes the behavior of materials in terminal stages of failure under conditions of approximately constant stress and temperature. Applicable to intact rock and rock masses, the relation may be extended to conditions of variable stress and cyclic stress, and may be used to predict time to failure. Applications in rock mechanics include slope and excavation stability and various topics in ground control.

Jan 1, 1989

By J. K. Whyatt

The paper presents an approach to design a multi level room and pillar layout in a 40m thick seam overlain by a major aquifer. The design was required to maximise extraction with due consideration of the general stability of the workings, the potential water hazards, and spontaneous combustion risks due to air leakage between horizons. The approach utilised was a combination of empirical pillar sizing for water hazard control with numerical modelling to assess potential interactions between horizons. The numerical modelling allowed the size of interleaves, and the appropriate staggers to be optimised in terms of stress distribution. The stress distribution allows both the general stability of the openings and more importantly the permeability changes around the openings to be determined. The permeability of coal is sensitive to stress, and an empirical stress to permeability relationship, and theoretical permeability to flow leakage relationship has been applied to interpreting the relative spontaneous combustion risk associated with each of the proposed layouts. The final proposed design is a compromise between maximum exploitation of reserves and consideration of water hazards and of spontaneous combustion risk. Further more detailed design will be required as more comprehensive data on the geotechnical properties of the coal and overburden become available.

Jan 1, 1996

By Quentin Rhoton

To benefit two endangered fish species, waterfowl and other wildlife, and water quality in the lake and downstream, the decision was made to remove levees that had been in place since the 1950s. Because the levee material was mainly dredged up lake bottom peat, it was decided to pare down the sites chosen for breaching with dozers and trackhoes. This material was spread out onsite instead of expensive removal by dumping elsewhere. Because of the instability of the final pared down levees and the lake level being at a ten-year low, it was decided to use explosives to breach four of the sites. After over five months of earthmoving and two weeks of loading holes, the levees were detonated the day before Halloween, 2007. Somehow pumpkins showed up to be part of the explosive activities.

Jan 1, 2009

By John Chipman, Wayne L. Worrell

Using recent thermodynamic data for the carbides and oxides of tantalum, columbium, and vanadium, the stable solid phases aboue 1300°K and at 1 atm CO(g) pressure in each M-C-O system have been determined. Pourbaix-Ellingham diagrams have been constructed and are used to estimate the minimum temperatures necessary to obtain these metals by carbothermic reduction under reduced pressures. TANTALUM, columbium, and vanadium react with carbon to form the M,C and MC carbide phases. The M,C carbides have narrow homogeneity ranges, but the MC phases possess considerable ranges of homogeneity.' The free energies of formation of the MC carbides were recently measured, and those of MC and M2Ccarbides have been estimated., (The notations MC and MC denote, respectively, the carbide compositions at the carbon-rich and at the metal-rich boundaries of the homogeneous MC phase.) In this paper, these carbide data are combined with thermodynamic data for the oxides to predict the stable phases in the Ta-C-O, Cb-C-O, and V-C-O systems at specified temperatures and oxygen pressures. M-C-O PHASE DIAGRAMS The solid phases in equilibrium above 1300°K for each M-C-0 system are shown in Figs. 1, 2, and 3. Above 1300°K, the vapor would consist entirely of carbon monoxide; and these phase diagrams were obtained by specifying the vapor pressure of CO(g) to be 1 atm. The temperature at which any two solid phases become unstable is specified along the two-phase equilibrium lines in each diagram. To simplify the diagrams, all solid phases in the Ta-C-O and Cb-C-O systems are represented as stoichiometric compounds. However, the homogeneity ranges of VO and VC are indicated, because they form a complete series of solid solutions.3 It also should be noted that the homogeneity range of

Jan 1, 1964

Reliable estimation of in situ stress is a major step in the analysis and design of underground excavations in rock, particularly for evaluating the stability of underground structures to prevent failure or collapse. In the last ten years, the Western Australian School of Mines (WASM) has studied and developed an AE stress measurement technique using orientated core named the WASM AE method. It allows the determination of a representative and detailed knowledge of the in situ stress field during the early stages of a project (such as mine feasibility studies), even in areas where development access is not yet available. The method has been used for in situ stress measurement at more than 80 mine sites worldwide with over 200 individual stress measurements carried out to date. This paper describes the sample collection, sample testing and reconciliation of results for very deep measurements carried out at the Craig-Onaping mine complex in Sudbury Canada. The results constitute the deepest measurements undertaken to date at the WA School of Mines and indicate that the main principal stress is horizontal and oriented parallel to a common regional sub trend in a NE/SW direction.

May 1, 2009

By Robert A. Bauer, Paul B. DuMontelle

In 1985, participants of the multi-year Illinois Mine Subsidence Research Program conducted surveys of subsidence effects on crop production from current high-extraction mining methods, selected a site to characterize the profile, strain, fracture development in overburden materials and changes in aquifers produced by subsidence from high-extraction mining, characterized floor materia1 s in three mines, and established bibliographic reference and data base files. The Illinois State Geological Survey, University of Illinois at Urbana-Champaign, Southern Illinois University at Carbondale, Illinois Department of Mines and Minerals and Twin Cities Research Center of the U. S. Bureau of Mines are coordinating State and Federally funded research.

Jan 1, 1986

By Carlos G. C

Geological mapping in various parts of Australia is revealing a number of regional associations of mineralizations with particular persistent stratigraphic horizons. Such associations have been found in the Broken Hill district of New South Wales, in the Nairne district of South Australia, in the Mount Isa district of Queensland, and in the Cloncurry district of Queensland. The question has arisen as to whether such mineralizations are of sedimentary origin, syngenetic with the enclosing formation, or whether they are of epigenetic origin, and reflect the selective hydrothermal mineralization of favourable beds on a regional scale.The purpose of this investigation is to test the use of sulphur-selenium ratios as an objective method of distinguishing between suphide deposits or sedimentary or supergene origin, and sulphide deposits of hydrothermal origin, with particular application to the districts mentioned. At the same time much data has been accumulated as to the selenium content of Australian sulphide ores. The possible use of sulphur-selenium ratios for this purpose was first demonstrated by Goldschmidt and his coworkers (1933; 1935), and later by Carstens (1941). Goldschmidt and Strock (1935) found that pyrite of sedimentary origin had a sulphur : selenium ratio of the order of 200,000 or more, whereas pyrite of hydrothermal origin had a sulphur: selenium ratio of 10,000 to 20,000. Carstensfound that sedimentary pyrite deposits in Norway contained less than 1 g. Se per ton, whereas hydrothermal pyrite deposits contained 20 to 30 g. per ton.

Jan 1, 1954

By M Lipalile, A B. Tunono, A W. Naismith

Konkola No 3 shaft experienced severe mining induced stress and time related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By Madsen I. C, Langberg D. E

Recent advances in X-ray diffraction (XRD) technology have made it possible to conduct powder XRD measurements on samples at high temperatures during reaction. State-of-the-art detectors are now capable of rapidly acquiring diffraction patterns across a wide angular range (typically 120"20) enabling phase transformation rates to be measured directly during sample reaction. In this study, the phase transformations during the reduction of hematite to metallic iron by five per cent hydro ºen in nitrogen gas mixtures, were measured in situ between 500 - 700 C. Complete X-ray diffraction patterns were acquired within 15 seconds every one minute, enabling direct measurement of the transient phase abundances during the reaction. The data were quantitatively analysed by the Rietveld method to yield the abundances of hematite, magnetite, wustite and metallic iron, as functions of time during the reduction process. A first-order reactions-in-series model was proposed, and the reaction rate constants and activation energy were determined from the time-dependent phase abundance data.

Jan 1, 1999

Industrial minerals by definition are minerals used as part of an industrial process and usually are one of a number of components, eg finely ground Limestone is an extender in the manufacture of paint. They are normally non-metallic and non-fuel, but like all generalisations there are a number of exceptions. Take rutile û a source of titanium, a metal and also the raw material in the manufacture of titanium dioxide pigment. Industrial minerals under this general definition include construction and agricultural minerals. They are included in the same grouping, principally because their sources are similar and in many cases the raw material, example limestone, can be multi-functional. Calcium carbonate raw materials such as limestone, are used in a wide range of applications from industry as an inert filler, to agriculture as a 'lime' source and to construction and as an important component in the manufacture of cement. As far as this paper is concerned I will avoid discussing the agricultural or construction applications, including burnt lime production.

Jan 1, 1985

By S. L. Karunakaran

Selection of an appropriate foundation system requires great skill and ingenuity on the part of the designer. Certain guidelines for choosing between a pile and raft foundation are presented. A number of methods are available for estimating the capacity of piles, giving a wide range of values for the theoretical load carrying capacity. A few aspects to be taken into account while arriving at an appropriate theoretical capacity are discussed. The effect of fluctuation of water table level on the pile capacity and method of accounting for this factor on the pile capacity obtained through initial load test are also discussed. A case study presents a comparison between the estimated values of capacity of piles and the values obtained through the initial load test.

Jan 1, 1996

By Eduardo Cabral

A nova política de resíduos sólidos, imagem positiva da empresa, utilização consciente de recursos com a consequente redução de custos e preservação do meio ambiente têm levado as minerações e siderúrgicas a adotar uma gestão responsável com relação aos seus coprodutos. Em consequência, esses coprodutos (escorias e lamas da mineração, lamas de aciaria, pós da sinterização, calcinação, coqueria, carepas e outros resíduos da siderúrgica) estão sendo economicamente reintroduzidos no processo produtivo. Esse trabalho pretende fazer um resumo de possíveis tratamentos que esses materiais podem sofrer, como umectação, aglomeração, briquetagem, granulação, pelotização ou extrusão.

Aug 16, 2017

By G. A. Kosick, C. A. Harris

"Metallurgy at the Polaris Mine is approaching an impasse, with lead and zinc concentrate grades and recoveries approaching their theoretical maximums. In an effort to increase productivity, plant throughput and operating material costs became a major focus of milling personnel.one method of increasing plant throughput was to minimize flotation circuit upsets by; standardizing operating strategy, decreasing control action response time of operators, increasing training of operators, and providing a more available decision support system for operators.To achieve these goals, Polaris personnel decided to utilize expert system technology to develop a real-time process controller for the flotation circuit which would be capable of justifying its actions to operating personnel.This paper describes the procedures followed in constructing the first process controller in the mineral industry which is based on the principles of Artificial Intelligence.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec and towed to its present location on Little Cornwallis Island, North West Territories, about 1450 kilometers from the North Pole. The plant presently treats about 2,800 MTPD of new feed with average feed grades of 3% Pb, 13% Zn and 5% Fe. Current production averages 36,000 tonnes of lead concentrate and 220,000 tonnes of zinc concentrate annually.In an effort to increase the efficiency of the concentrator, the decision was made to implement an innovative control system on the flotation circuit. This system would embody and utilize heuristics ""rules-of-thumb"" gained from operators to make on-line process decisions. It would also justify these decisions on a demand basis."

Jan 1, 1988

By A M. Hagni

Certain copper ores from the Nchanga Copper Mine in the northern Zambia Copperbelt are refractory with respect to conventional beneficiation techniques. This paper reviews recent study of those ores to determine their mineralogy, textures and nature of copper occurrence. Two suites of refractory ores were selected for study: 1.  samples of stockpiled ores from an open pit, and 2.  drill core samples from copper ores. Both sample suites are from the upper orebody at Nchanga and contain about 0.3 - 1.4 per cent copper as determined by atomic absorption, but they represent separate stratigraphic, mineralogical and beneficiation problems. Ore microscopic examination showed that fine-grained copper sulfides are totally lacking from both suites of refractory ores. Petrographic study found malachite in the refractory ores from the open pit, but that malachite probably is post-mine. The opaque mineralogy of the open pit refractory ores is dominated by goethite that occurs mostly as pseudomorphic grains after pyritohedral pyrite crystals that average 200 - 250 ¦m across. Haematite occurs as bands within or as outer shells of the goethite grains. Additional goethite occurs locally as finer-grained areas of exotic goethite. The opaque minerals in the drill core refractory ores are dominated by euhedral ilmenite crystals about 50 - 175 ¦m long. Anatase is the dominant opaque mineral in some drill core samples where it is largely pseudomorphic after ilmenite crystals. Goethite accompanies malachite in unusual drill core refractory ores that have experienced intense hydrothermal alteration. Thus, ore microscopy and petrography showed that fine-grained chalcopyrite and bornite and pre-mine malachite were not the causes of the refractory nature of the ores studied. Electron microprobe revealed that most of the copper occurred in solid solution within micas. Application of automated SEM techniques has provided a detailed understanding of the distribution of copper in these refractory ores.

Jan 1, 2008

By M. du Toit

Cromanite?is a new high-strength austenitic stainless steel developed by Columbus Stainless. It contains approximately 19 percent chromium, 10 per cent manganese and 0,5 per cent nitrogen. Cromanite can be welded successfully, but due to the high nitrogen content of the base metal, certain precautions have to be taken to ensure sound welds with the desired combination of properties. Although no matching filler metals are currently available, Cromanite can be welded using a range of commercially available stainless steel welding consumables. Welds produced using E309L, E307, E307Si and E312 filler wires are resistant to hot cracking and the formation of nitrogen-induced porosity, but the hardness, strength, ductility and toughness of the welds are generally inferior to those of the base metal. In applications where full use is made of Cromanite?s high strength, welds with matching strength levels would be required. In wear applications, where Cromanite is used primarily for its work-hardening properties and corrosion resistance, lower strength welds would probably be acceptable. Welds produced using E307 filler metal demonstrate the best combination of properties for use in wear applications. The welds display high rates of work-hardening that would result in increases in hardness and strength when subjected to abrasive or high impact environments.

Jan 1, 1999

By S D. C Rabone

An elongate belt containing granodiorite stocks with associated stockwork molybdenum mineralisation in west Nelson is correlated with the I-type Separation Point Suite of mid Cretaceous age. Trace element characteristics of the 'Mo-granites', and the Separation Point Batholith strongly suggest a primitive, subcrustal origin for these granitoids, by partial melting of oceanic basaltic crust or upper mantle material in a subduction zone. They were emplaced in the upper crust without undergoing significant differentiation or contamination by sialic crust. Molybdenum, which is at levels of approximately 5 ppm in unaltered granite, is not significantly reduced in altered (but unmineralised) granite. This suggests the metallisation has a magmatic, subcrustal source and is not derived by hydrothermal leaching of upper crustal rocks or the granitic host rocks. Geochemistry of the 'Mo-granite' belt, in particular low K2O, calc-alkali to calcic Peacock Index, high Sr and TiO2, and low Rb, Nb and F, suggest classification as calcic granitoids similar to those which host porphyry copper deposits, indicating grades of mineralisation are likely to be low.

Jan 1, 1987

A clear understanding of the meanings of terms is important when discussing a project. Whether it is a submission, an investment study, a feasibility study, an environmental impact statement, an estimate, a tender, a contract, or a close-out.report, the need for all parties involved to understand what is under discussion or what has been written is paramount. The clarity of definition and the level of understanding can affect the outcome of the project. It is vital that all parties know what is wanted, what is expected, and what it will cost. This paper draws attention to some of the problems that beset many projects, clients, project managers and contractors, and it is hoped that its presentation will encourage us to pay more attention to defining what it is that is required. Ultimately we should all be the richer for having defined and understood the requirements at the beginning rather than at the end.

Jan 1, 1990

Northern Iron Ltd (NIL) is an Australian listed company that recently brought the historic Sydvaranger open pit Magnetite Mine (the Project) in Northern Norway successfully back into production. NIL made the decision to operate the Project on an owner mining basis, due to limited large scale mining expertise amongst Norwegian mining contractors, a long mine life, a limited range in planned mining rate and to minimise costs. As a new mine operator in a country where labour practices are strictly regulated, there was the desire to reduce the risk associated employing and managing skilled personnel. This was achieved by coupling the purchase of the required mining equipment from the original equipment manufacturer's (OEM) regional dealers with OEM supported Maintenance and Repair Contracts (MARC). This paper examines the process that was followed to implement an owner mining operation in a short time frame; approximately 12 months from the initial requests for quotation to actual delivery of mining equipment to site, and some of the challenges faced. By following a formal and well-tested process, not only was the implementation achieved in the set time frame, but significant value was added through the cost savings achieved in the equipment purchase price and MARC rates that were negotiated through this process.

May 1, 2010

By A Croll

A panel cave using LHDs for ore extraction came into production at Premier in 1990 at a depth of 630 metres below surface on the western side of the mine in the BA5 mining block. A post-undercut mining sequence was used with all development on both the undercut and production levels completed prior to the undercut being advanced over the pre-developed drawbells. Support and rock mass damage on the production level was extensive as the undercut moved overhead. Undercutting and coarse fragmentation created problems. The mining sequence was changed to an advance undercut with the minimum of development and support undertaken on the production level prior to the undercut moving overhead. Only once the abutment stresses had stabilised were drawbells developed and final support installed. The height of the undercut drill design was decreased from 18 to 13 metres. The changes resulted in markedly less rock mass and support damage on the production level. Lessons learned in the BA5 mining block on the 630 level were incorporated into planning and scheduling the BB1E mining block which came into production on the 732 metre level on the eastern side of the mine in 1996. An advance undercut mining sequence was planned, undercut height was minimised and undercutting parameters were optimised in terms of the BA5 experience. Numerous problems still occurred. As the undercut area increased in size severe spalling from the cave back resulted in vertical propagation of the cave to a height of 30 metres instead of the planned 13 metres. The resultant coarse fragmentation created secondary blasting problems and an excess of undercut ore that had to be loaded and trammed, slowed the rate of undercut advance. The planned mining sequence was compromised and considerable support and rock mass damage resulted on the production level below. Once these problems had been overcome the undercut advanced at the planned rate and continuous caving initiated at the predicted hydraulic radius. At a later stage the unexpected ingress of water hampered undercut drilling and slowed the rate of undercut advance in a section of the cave. Leads and lags between adjacent tunnels and the overall face shape could not be developed as planned. The rate of natural horizontal cave propagation exceeded the rate of undercut advance and three undercut drilling tunnels were extensively damaged. More tunnel development on the production level prior to undercutting than was planned resulted. The slow advance of the undercut and high abutment stresses caused extensive damage to installed support and the rock mass on the production level, 15 metres below. Experience in the BB1E mining block on the 732 metre level has taught that an advance undercut mining sequence reduces damage on the production level markedly. Extremely tight control on the rate of undercut advance, leads and lags between adjacent tunnels and overall undercut face shape as well as extraction ratio, tunnel development and support sequence on the production level below is required. Premier Mine plans to implement a block cave at a depth in excess of 1000 metres within the next decade. All the experience gained on current mining levels together with data collection and numerical modeling is being used to plan the proposed mining operation. The geotechnical challenge of mining at this depth in weak rock has been identified as the greatest risk to the project. Challenges centre around adopting the correct mining sequence, limiting the extent of rock mass damage associated with undercutting and effective support. The hydraulic radius needed to initiate caving, fragmentation, drawpoint spacing, secondary blasting and the possibility of seismicity are geotechnical concerns that are being addressed. Results to-date suggest that a pre-undercut mining sequence with all development and support on the production level carried out only after the undercut abutment stresses have passed overhead will have to be implemented.

Jan 1, 2000