Search Documents

By Guiqing Zhang, Liansheng Xiao, Zuoying Cao, Li Zeng

A new process of direct solvent extraction of nickel from sulfuric acid leach solutions of low grade and complicated nickel resources using a novel extractant HBL110 was proposed. The basic performance of new organic system was investigated and the continuous pilot plant and the industrial test were conducted. The results indicated that the extractant of HBL110 can be used to directly extract nickel selectively over iron, aluminum, manganese, magnesium, calcium and chromium from sulfuric acid leach solutions. The loaded organic solution can be easily stripped using dilute H2SO4 solutions. Both kinetics of extraction and stripping of nickel were fast. The continuous pilot plant test with the sulfuric acid leach solution of laterite containing 6.22g/L Ni2+, 14.1g/L Fe3+, 0.73g/L Fe2+, 33.9g/L Mg2+, 1.58g/L Al3+, 0.495g/L Ca2+, 0.97g/L Mn2+ and 0.5g/L Cr3+ as feed in mixer-settlers showed that the process had run stably with 98% recovery of nickel. The concentration of nickel in strip liquors reached as high as 50 g/L while the removals of Fe3+, Fe2+, Mg2+, Al3+, Ca2+, Mn2+ and Cr3+ were 98.5%, 91.5%, 99.95%, 99.8%, 99.1%, 98.6% and 99.5%, respectively. The industrial test with the sulfuric acid leach solution of electroplating sludge containing 11.5g/L Ni2+, 2.68g/L Fe3+, 7.54g/L Cr3+, 0.61g/L Mg2+, 2.09g/L Al3+, 0.68g/L Ca2+, 0.022g/L Mn2+ and 0.154g/L SiO2 as feed in mixer-settlers also showed that the process had operated successfully with 99.5% recovery of nickel. The concentration of nickel in strip liquors reached 42.7 g/L while the removals of Fe3+, Cr3+, Mg2+, Al3+, Ca2+, Mn2+ and SiO2 were 99.2%, 99.77%, 99.73%, 99.56%, 99.57%, 98.51% and 98.75%, respectively. The new process exhibited big advantages of short flow sheet, high recovery of nickel, high removal of impurities, low chemical reagent consumption and low cost. Application of this process in industry is expected to make important impact on the extraction of nickel from sulfuric acid leach solutions and to deliver good environmental and economical benefits.

Jan 1, 2016

By Masao Suzuki

Over 5 million cars are scrapped yearly in Japan. After dismantling. scrapped automobiles, they are put into a shredder for differential recovery of ferrous and nonferrous metals. The residue, which is called shredder dust, runs over 1.2 million tons per year. This paper reports a entire sequence of scrapping. cars. in Japan with the following sections: (1) production and scrapped car management, (2) material composition, (3) dismantling, (4) shredder plant, (5) differential recovery of metals including specific gravity separation and newly developed color separation.

Jan 1, 1995

By Kuo En Chang

Many rare earth - transition metal (RE-TM) compounds absorb/desorb hydrogen reversibly at room temperature and atmospheric pressure. For LaNi5 which is used as a battery material, the electrochemical nature of this process is well known. In the case of Nd-Fe-B which has found wide application as a powerful permanent magnet, the absorption of hydrogen has both significant advantages and disadvantages. However, a fundamental understanding of the hydrogenation process at ambient temperatures and its effect on subsequent corrosion behavior is currently lacking. This paper reports the results of the hydrogenation of NdFeB two alloys, (NdDy)15Fe78.3A10.7B6 and (NdDy)15Fe67Co5V4A12B7, which are compared with that of LaNi5. Results show that hydrogenation can be accomplished by either electrochemical methods or immersion in dilute sulfuric acid. For the latter method, the change in lattice parameter indicates that the level of hydrogen absorbed by the NdFeB particles corresponds fairly closely to an overall composition of Nd2Fe14BH2.7. Cyclic electrochemical charge/discharge experiments show that the maximum hydrogen discharge capacities of the NdFeB, NdFeB-Co-V, and LaNi5 are 40, 60, and 210 mA?h?g-1, respectively. Anodic potentiodynamic polarization measurements and calculated values of icon reveal that absorbed hydrogen in NdFeB-Co-V and the NdFeB may lead to significant increases in corrosion rates.

Jan 1, 1995

By Raymond E. Healy

Circuit samples from the HBMS concentrator were assayed for l5elements, and image analysis was done to determine the modal quantities, grain size distributions and liberations of the minerals. Material balancing was done on these data to determine distributions of the minerals in each concentrator stream. The ore was mined during the waning phase of mining and is diluted with backfilled copper smelter slag. The mill feed grades 1.0 wt% Cu and 1.8 wt% Zn. The slag silicate phases contain approximately 1.5 wt% Cu and 6.5 wt% Zn; therefore the Cu and Zn head grades due to chalcopyrite and sphalerite, are only 0.9 wt% Cu and 1.2 wt% Zn, respectively. The recovery of Cu in the Cu-concentrate (Cu-conc.) is only 77.5 %, whereas that of chalcopyrite is 89.2 %. Similarly, the recovery of Zn in the Zn-concentrate (Zn-conc.) is only 40.2 %, whereas that of sphalerite is 71.0 %. The slag accounts for approximately 60 % of the Cu, and 85 % of the Zn in the tailings. The main loss of chalcopyrite is as unliberated grains to the tailings, and the main loss of sphalerite is as free grains to the Cu-concentrate and as unliberated grains to the Cu-concentrate and tailings. Approximately 85 % of the chalcopyrite and sphalerite lost to the tailings. accounting for 8 % and 10 % of the respective minerals in the concentrator feed, occur as middling and sub-middling grains. Extremely fine regrinding would be required to liberate these minerals.

Jan 1, 1989

By T. Iriyama, Y. Fujita, R. Omatsuzawa, T. Nishio, N. Okochi

Sm-Fe-N hard magnetic materials are good candidates for high performance bonded magnets. Rapid-quenching method should be highly favorable for the fabrication of isotropic magnet powder with high coercivity. We report here the magnetic properties of Sm-Fe-N powders produced by a few kinds of rapid-quenching processes. Sm2Fe17 powders were prepared by gas-atomization (GA), rotating-disk atomization (RDA), or melt-spinning (MS) method. The Sm2Fe17 GA powder had dendritic solidification structure, while the RDA powder had micro crystalline structure with size of 3-5 µm. Coercivities (HcI) of their nitrides were 56 (for GA) and 217 ka/m (for RDA). The H cI of nitrided Sm2Fe17 MS powder with wheel velocity (V5) of 5-20 m/s, which had also microcrystalline structure, was 53 to 509 Wm. These coercivity values are not sufficient for bonded magnet applications. From the study of additive effects, it was found that C, C-Si, C-Ga, or C-Al addition decreased the crystal size of quenched Sm2Fe17 powder. Consequently, high coercivity was obtained; the HcI of nitrided Sm2Fe1C1Si1 MS powder with V5 of 10 m/s was 898 kA/m, and 708 kA/m for the nitrided Sm2Fe15C1Si1 RDA powder. The compression-molded bonded magnet made from Sm2Fe18Si0.1Nx MS powder showed a high (BH)max of 82.7 kJ/m3.

Jan 1, 2000

Steel Ladle in Bhilai Steel Plant, SAIL, India, passes through VAD & LF-RH route and this exposes refractory lining to a severe operating conditions. Ladles are lined with in-house manufactured MgO-C refractories. Lining life used to be 35 heats, out of which 18-20 heats were through VAD/LF-RH, hence, ladle availability had become a constraint. Laboratory studies were carried-out to optimize granulometry and composition. Granulometry was developed by adopting Andearssen packing model. A suitable plasiticiser was identified to eliminate inconsistency caused due to variation in resin quality and weather condition. It reduced variation in green bulk density from 6 to 1.3%. Abrasion and slag erosion studies were conducted, which shows that with increase of carbon, abrasion resistance decreases and corrosion resistance improves. Based on these studies, graphite in slag zone was increased from 10 to 12.5% and in metal zone it was reduced to 7.5%. Different process parameters of brick making were optimized to make MgO-C bricks of maximum bulk density with reduced coke porosity. Modified bricks have bulk density of 2.99-3.02 g/cc and coke porosity of 9.5-10.5%. Further, shape of the bricks were changed from side arch to mini keys and thickness was increased from 80 to 100 mm. Mini key bricks are pressed from sides, thus eliminating variation in thickness which is critical dimension for dry joints. These modifications improved average lining life of steel ladles to 64 heats, which includes 37-40 secondary heats. Maximum life obtained is 87 heats.

Jan 1, 2006

By William Petruk

The concentrator of the Iron Ore Company of Canada consists of spiral circuits, a cone plant and a magnetics plant with regrind. The proportions of liberated and unliberated grains of iron oxides at each point throughout the concentrator were measured by image analysis, and recoveries were calculated for each particle type by the MATBAL materials balancing program. The results show that spirals and cones recover more than 92% of the liberated iron oxide grains in the size range of 848 to 150 um,, but the recovery drops off rapidly for finer grained particles. The tailings from the spirals and cones are reground and low intensity magnetic separators are used to recover liberated magnetite in the -37.5 um size range. The concentrator does not have a unit that efficiently recovers iron oxide grains in the size range of 150 to 37.5 um Consequently about 25% of the iron oxides in the ore are lost to tailings as liberated. grains in the size range of 150 to 37.5 um

Jan 1, 1989

By Qian Xu, Xionggang Lu, Xingli Zou, Zhongfu Zhou, Shuhua Geng, Hongwei Cheng

Herein we report an electrochemical route from oxides (SiO2, TiO2)/sulfide (MoS2)/carbon mixture precursors to Mo-Si-Ti-C composites in molten salt. The electrochemical process was carried out in molten CaCl2 at 800 °C with a potential of 3.1 V, and a graphite-based anode was used in the electroreduction process. The reaction mechanism and the influences of the stoichiometry of the initial mixture precursor on the morphology and phase composition of the final products were investigated. It has been found that Mo5Si3/MoSi2/Mo3Si/Mo, Mo5Si3/MoSi2/Mo2C/SiC, and Mo5Si3/Mo2C/Ti3SiC2/TiC/Mo composites can be electrosynthesized directly from their oxides/sulfide/carbon mixture. The preliminary experimental results suggest that the electroreduction process can be used for the controllable electrolytic production of alloys/carbide-containing composites from oxides/sulfides/carbon precursors.

Jan 1, 2016

By Qingzhu Li

The adsorption process of Pb2+ from aqueous solutions by spent grains modified with Imol/L NaCI solution was investigated. The effects of solution pH, contact time, adsorbent concentration, initial Pb2+ concentration, particle size on Pb2+removal were also studied. The initial adsorption process was rapid and 90.35% of Pb2+ adsorption occurred within 30 min. The absorption equilibrium was obtained at 4h. When pH was 5.5, Pb2+ concentration in aqueous solutions decreased from the initial content of 20 mg/L to 0.0 I mg/L after 5 hours by application of IOg/L adsorbent at 25?C, Pb2+ removal efficiency reached up to 99.95% and the Pb2+ remaining in aqueous solutions was under China Sanitary Standard for Drinking Water (GB5749-85). Adsorption data fitted well with Lanf+muir and Freundlich models. However,Langmuir isotherm model was better to descnbe Pb- adsorplion than Freundhch model, mdlcatmg that the applicability of monolayer coverage of Pb2+ on the surface of adsorbent.

Jan 1, 2008

By N. Bazzanella

The hydrogen desorption kinetics of pure and Nb-doped magnesium hydride film samples was investigated by using a Sievert-type apparatus. The overall activation energy and the reaction order controlling desorption are (141±5) kJ mol-1H and n 4 for Mg hydride and (51±5) kJ mol-1H and n 1 for Nb-doped (5% at) Mg hydride indicating that, in the doped sample, hydrogen desorption is controlled by the H migration in transformed h-Mg layers. Structural analysis performed by X-Ray Diffraction (XRD) and Extended X-Ray Absorption Fine Structure spectroscopy (EXAFS) show that the catalytic effect of the Nb dopant is connected with the formation of NbH0.89 nanoclusters dispersed in the Mg hydride matrix. It is suggested that the catalysis process is also connected to the presence of Mg-Nb hydride interfaces where the transfer of H atoms preferentially occurs by connecting h-Mg grains and by the role of the MgH2-NbH0.89 interface as preferential site for the dissociation of the hydride phase.

Jan 1, 2006

By L. -C. Lai

A series of LaNi5-based alloys, with partial substitution of Ni by Al, Co, or V, were prepared The gas-phase hydrogen absorption kinetics and pressure-composition-temperature curves were measured The activation became easier and the plateau pressure was reduced as Ni was partially substituted by Al Substitution with Co reduced the hysteresis as well as the hydrogenation capacity, but enhanced the absorption kinetics Vanadium is often considered as a hydride former, but when it was added to LaNi5, it was found that V occupied the B site. A small amount of substitution of Ni with V led to a higher hydrogenation capacity and faster activation rate Based on these properties, an alloys LaNia 25CO0.5V0.1Al0. 15 was fabricated as an electrode. Compared with LaNi4.85Al0.15, it was found to exhibit faster activation, higher discharge capacity, and longer cycle life. The variation of the hydrogenation characteristics is discussed based on the physical and chemical properties of the alloying elements.

Jan 1, 1997

By Hiroshi Nakazawa

An acid mine drainage in abandoned Horobetsu mine in Hokkaido, Japan, contains arsenic and iron ions; total arsenic ca.10ppm, As(III) ca. 8.5ppm, total iron 379ppm, ferrous iron 266ppm, pH1.8. Arsenic occurs mostly as arsenite (As (III)) or arsenate (As (V)) in natural water. As(III) is more difficult to be remove than As(V), and it is necessary to oxidize As(III) to As(V) for effective removal. 5mL of the mine drainage or its filtrate through the membrane filter (pore size 0.45m) were added to arsenite solutions (pH1.8) with the concentration of 5ppm. After the incubation of 30 days, As(III) was oxidized completely with the addition of the mine drainage while the oxidation did not occur with the addition of filtrate, indicating the microbial oxidation of As(III). In this paper, we have investigated the microbial oxidation of As(III) in acid water below pH2.0.

Jan 1, 2006

By Fiseha Tesfaye, Pekka Taskinen

"A thermodynamic study of the equilibrium phase assemblage AgBi3S5-Bi2S3-S was made by an EMF-technique, using the RbAg4l5 solid electrolyte. The ternary phase was synthesized from the pure Ag2S and Bi2S3 in an evacuated silica ampoule and grinded into powder and mixed with appropriate compositions of B12S3 and S, in a series of experiments, for pressing in to pellets. The pellets were assembled to form the galvanic cells Pt (-) | Ag ] RbAg4ls | AgBi3S5+ Bi2S3 + S + (C) I Pt (+). The EMF-measurements were made in the temperature range 299 - 460 K.In this paper, thermodynamic functions of the ternary phase AgBi3S5 (pavonite) have been determined. The agreement between the obtained results and the literature values were established.IntroductionThe complex group of ore minerals constitutes from trace amounts to a major proportions of sulfosalts. Although the sulfosalts rarely form massive ore bodies, they are commonly associated with rich sulfide ore minerals for the base and precious metals and widely distributed in a metal poor sulfide minerals [1]. For instance, Ag-bearing sulfosalts are encountered in ore minerals for the production of the base metals and are common sources of silver. Nevertheless, thermodynamic properties of the sulfosalts are poorly known.Reliable thermochemical data are essential for quantitative modeling of the chemical behavior of the sulfosalts in equilibrium with sulfides, which in turn would promote the optimization of complex minerals treatment and extractive metallurgy of the valuable metals."

Jan 1, 2012

By M. -V. Wang

Hydrotreating and hydrorefining (HT and HDS) spent catalysts contain molybdenum, vanadium, nickel or cobalt at concentration levels that can make metals recovery economically viable. Quanzhou Jing-Tai of China has developed, through many years of operating experience in metal recovery from spent catalysts, a simple process for recovery of these metals and the production of environmentally benign residues. The process first subjects the catalysts to a low-temperature calcination step, followed by grinding of the calcine. The ground material is then leached with 10-20% v/v hydrogen peroxide to recover metals such as Mo, V and Ni or Co. This step has a selectivity that is greater than 95% for the metals. The undissovled residue, which contains mainly Ah03 and Si02, can be dewaterd and used in the production of masonry bricks. The pH of the rich liquor is then adjusted to between 0.5 and 2.5 by adding dilute sulfuric acid to co-precipitate Mo and V, with a recovery rate of greater than 99%. The lean liquor contains mostly dissolved Ni or Co, which can be recovered through precipitation at a pH of between 8.5 and 9.5 by caustic additions. The final liquor is then sent to an ion exchange step for final recovery and cleanup of residual metals. The effluent is then discharged after a simple wastewater treatment process, which has been found to meet all environmental requirements. The entire process has been found to be simple, cost-effective with minimal environmental impacts while achieving the goal of complete resource recovery from spent catalysts commercially.

Jan 1, 2000

By Juan Daniel Martínez, Janaina Accordi Junkes, Dachamir Hotza, Tatiana Pineda

"The rice husk combustion in a bubbling and atmospheric fluidized bed reactor was investigated. The results showed the technical viability of producing both heat and amorphous silica from a renewable energy source. This paper presents the characterization of rice husk ash (RHA) obtained under varying fluidization velocities (0.13-0.15 m/s) and rice husk feed (4.5-7.2 kg/h). Characterization techniques include X-ray fluorescence, X-ray diffraction, particle size distribution and scanning electron microscopy. For the employed range of fluidization velocities of rice husk feed no noticeable influence on the chemical composition of produced RHA was observed. After combustion, RHA containing ~93% amorphous silica and <3% unburned char was obtained. RHA primary particles presented sizes from 90 to 100 µm and a tendency for agglomeration in aqueous media. Thus, the potential of this type of reactors with respect to speed, continuity and self-sufficiency energy of the process was shown.IntroductionDue to the increase of the agroindustrial production, the concern with processing by-products, such as rice husk (RH), is growing. For a better material and energy use, allowing a cleaner production and a more maintainable development, RH can be used as renewable fuel in the production plant, for instance, in steam generators. The adequate combustion of RH generates hot gases with low levels of pollutants, as carbon monoxide and particulate material.RH is the protecting coating formed during the growth of the rice grain, composed by four structural layers.1 The main components of the husk are cellulose and hemicelulose (50%) besides lignine (26%) and organic components (4%), as oils and proteins. The remaining amount includes inorganic materials (SiO2, Al2O3, K2O, Na2O, MgO, CaO, Fe2O3, MnO, P2O5).1The rice husk ash (RHA) is the product of the termochemical transformation of RH. The conditions of the different conversion processes (pyrolysis, gasification and/or combustion) determine the physical-chemical characteristics of the final product. RHA corresponds to 14 to 25% RH, depending on the variety of the rice, climate and soil of the producing area.2-4 The main component of RHA, which is generated at moderate combustion temperatures, is amorphous silica (SiO2) in the range from 80 to 97%.4,5"

Jan 1, 2008

By Carole Read

Hydrogen is under consideration by several countries for its potential as an energy carrier for transportation applications. In order to compete with vehicles in use today, hydrogen-powered vehicles will require a driving range of greater than 300-miles in order to meet customer needs and expectations. For the overall vehicular light-duty fleet, this dictates that a range of 5 to 13 kg of hydrogen be stored on-board (assuming a fuel cell power plant) within stringent system weight, volume, and cost constraints. Vehicular hydrogen storage thus constitutes a major scientific and technological challenge. To meet this challenge, the U.S. Department of Energy (DOE) initiated a ?National Hydrogen Storage Project? with roughly 40 universities, 15 companies and 10 federal laboratories, actively engaged in hydrogen storage research. Centers of Excellence in metal hydrides, chemical hydrides, and carbon-based materials have been established, as well as independent university and industry projects in the areas of new concepts/materials, hydrogen storage testing, and storage system analysis. Recent technical progress in each of these areas is discussed, as well as collaborative hydrogen storage activities under the recently established International Partnership for the Hydrogen Economy (IPHE).

Jan 1, 2006

By Y. Z. Zhang

Electrochemical oxidation of arsenopyrite in ferric sulphate media in the absence and presence of bacteria T jerrooxidans has been investigated for the purpose of understanding the dissolution chemistry of arsenopyrite and the bacteria attack mechanism. Mixed potential, polarization resistance measurements, polarization curve, cyclic voltammetry experiments were conducted in a ferric sulphate medium of 10g/L FeH, temp.25-35°C, pH 1.5-2.5 in the absence and presence of bacteria Tjerrooxidans, respectively. For the anodic process, a two-step reaction sequence is suggested by the electrochemical measurements. The initial step at a low potential is described by:

Jan 1, 1996

By John Sakala, Jeyapandian Sasikumar, Sydney Kwalela

The Isasmelt Furnace was commissioned in September 2006 with a concentrates treatment capacity of 850,000 tonnes per annum. However, the converter section became a bottleneck to the high throughput. Over 25% of the Isasmelt Furnace down time was attributed to lack of converter space. Factors that affected converter operations were low tuyere line campaign life (an average of 150 blows), high reverts generation, low conversion rates, and high converter cycle time. As a result of efforts carried out to improve converter operation, the average campaign life has increased to over 250 blows and reverts generation has been reduced from 22% of concentrate treated to 15%. Blister copper conversion rate has increased from 15 tonnes per hour to 19 tonnes per hour and blowing time per cycle has been reduced from 5.7 hours to 4.7 hours.

Jan 1, 2012

By Lawrence L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P2O5 is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pet P2O5 and a P2O5 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1982

By Christopher B. Vierrether

Reflected light microscopy, scanning electron microscopy, and electron microprobe analysis have been used to determine the mineralogy, phase percentages, grain sizes, textures, and partitioning of cobalt and nickel in two cobalt-nickel rich mattes. These mattes were prepared by submerged bath smelting from a flotation cobalt-nickel concentrate containing 4.8% cobalt and 5.1% nickel. The concentrate was derived from lead-zinc-copper ores of the Viburnum Trend, southeast Missouri. Eleven discrete phases have been distinguished in the matte samples, three of which contain significant cobalt and nickel. The phases are cobaltpentlandite ((Co,Ni,Fe)9S8), cobalt-bearing marmatite ((Co,Fe,Zn)S), shandite (Ni3Pb2S2), bornite (Cu5FeS4), galena (PbS), magnetite (Fe3O4), pyrrhotite ((Co,Ni,Cu,Fe)1_xS), chalcocite (Cu2S), CuPbS phase, metallic copper, and metallic silver. Cobaltpentlandite and cobalt-bearing marmatite- occur in coarse grains (50 µm) that would separate readily during grinding, but shandite contains small (5 - 10um), abundant inclusions of pyrrhotite and bornite.. Some mineralogical variations between the two matte samples were due to differing degrees of oxidation during smelting,

Jan 1, 1988