Search Documents

By C. E. Dodson

Conventionally hydrometallurgical recovery processes from sulphide concentrates include roasting, leaching, precipitation, impurity removal and zinc electrowinning. The use of the novel (yet commercially proven in other mineral and metallurgical industries) TORBED process reactor for the flash roasting of sulphides will be proposed. The potential advantages in its application will be discussed including very fine particle processing capability, lower cost smaller roasters, waste minimization, improved leaching efficiency and overall process simplification.

Jan 1, 1999

By W. G. Davenport

Flash smelting is used. mainly for making molten Cu-rich matte* from fine Cu-Fe-S** flotation concentrates. It blows dried concentrate particles into a hot fumace, surrounds them with 01-rich gas and allows them to react. The results are: (a) partial oxidation of Fe and S from the concentrate (b) generation of heat (c) melting of the oxidized particles to form molten Cu-rich matte, ~65% Cu and Cu-barren slag, ~1 % Cu. The melted particles fall to the hearth of the flash furnace where they fonn matte and slag layers, The matte is tapped from the furnace and oxidation-converted to metallic copper. The slag is skimmed, treated for Cu recovery then stockpiled or sold. Figures 1.1 and 1.2 show industrial flash furnaces and the position of flash smelting in the coppermaking flowsheet. ,Fig. 1.3 shows the locations of flash furnaces around the world.

Jan 1, 2001

By Norbert Steiner

For the desulfurization of weak SO2 gas streams, Degussa developed a process using dilute H2SO4 solution containing H2O, instead of conventional gas scrubbing with all solid absorbent medium (limestone, MgO). The process is based on fast reaction of H2O, with SO2 yielding H2SO4 up to 70% strength, depending on off-gas temperature. Compared to the conventional systems with typically < 95% efficiency, independent on the raw gas SO2 concentration, residual SO2 concentrations of less than 20 mg/Nm3 can be easily achieved, corresponding to nearly 100% removal. These features render the H2O, process a very attractive, low capital cost technology to retrofit existing conventional desulfurization plants.

Jan 1, 1996

By D. J. Wang

Based on the thermodynamic arid kinectic aspects, the vaccum distillation processes for the separation and recovery of metals from wastes are analyzed. As to the separation criteria, The separation coefficient and equilibrium composition relation between vapor phase and liquid phase are the bases of recovery of metals by vacuum distillation, The vaporization rates and condensation mechanisms are also discussed. Some experimental results which deal with metals-containing wastes are described and the performances of a new kind of horizontal vacuum furnace are introduced, which demonstrate that , vacuum distillation may be a prospective technique for circulation and regeneration of some non-ferrous metals from industrial wastes.

Jan 1, 1996

By Peter Bauer, Klaus Gamweger

"Gas purging systems are well established in nonferrous metallurgy at multiple steps during metal production, including melting, converting, alloying, and metal cleaning. Since the kinetics of all of these stages are positively influenced by using gas purging systems the overall process benefits are substantial. In the aluminum industry, inert or reaction gases are blown into the melt using porous plugs to achieve improved metal grades, higher productivity, and more efficient energy utilization. To enable the most effective application of the process gases a complete package, termed AL KIN, was developed by RHI that includes porous plugs, refractory expertise, gas supply technology, and gas control equipment. This paper discusses the technological and economic advantages of this system and the specific benefits of fuel reduction, production time savings, decreased process gas consumption, and improved refractory service life and maintenance are illustrated using an aluminum slug plant in Austria.IntroductionIn addition to high quality production, increasing productivity is the main goal in many aluminum cast houses to maintain or even strengthen their market position. The Neuman Aluminium Group, based in Austria, North America, and based in Austria, North America, and China, is the largest slugproducer for tubes, cans, and automotive parts worldwide. Recently, a comprehensive improvement program was initiated at the Neuman Aluminium Austria slug plant in Marktl - the main factory and technological centre of the group. The principal goal of the optimization project was to increase the productivity of the strip-casting production. The investment included a gas purging system, ingot preheating equipment, a new insulated launder system, and optimized melting cycles. However, the introduction of the gas purging system was pivotal to the project and has accounted for approximately 50% of the benefits achieved. This paper describes the AL KIN gas purging technology and details the process benefits resulting from the improvements at Neuman Aluminium Austria."

Jan 1, 2009

By Viktor. P. Popov, Oleksandr. V. Derev'yanko, Oleksandr. I. Raychenko

"This paper is devoted to scrutiny problem of obtaining electro-contacts by electro-discharge sintering technology. A new unconventional method of electro contacts production (on Aggraphite base) can yield essential optimization resource.Review of three electro-technological methods of processing contacts materials is presented:- using graphite powder cladded by Ag;- mixture of graphite powder(which is a non-cladded powder) with Ag powder and addition of Fe powder particles;- method of infiltration of melted Ag into graphite piece without deformation and rupture of object.This technological approach can give the possibility to increase of compression strength of electro-contacts materials up to 340 MPa and more under conditions of additional reinforcing components (for example, by Fe).IntroductionThe electric current can be an active ""participator"" of the powder metallurgy technology [l]. At the passage of electric current through powders or some powder mixtures the phenomena including phase transformations arise. Here such effects, which are observed in the Ag-graphite and Ag-Fe-graphite powder mixtures and in the pair Ag-porous graphite, are described.The Ag-graphite composition materials (CM) are used, for example, as electric contacts [2, 3]. Since a material being produced is destined for the contacts it is necessary to take into account the following aspects: commutating current, its character and voltage, active or reactive character of working load, geometrical dimensions of contacts, quantity and frequency of switching on and switching off, pressure on contacts, distance between contacts, method of arc control, surrounding medium, its content, pressure and temperature. Thus, these and, maybe, choice of some other circumstances influence design, materials and production technology of contacts. The range of problems concerned dictates such steps as alloying of contact materials, optimization of structure, selection of kind of graphite, its connection with metal [4-10]. It is expedient to recall the main procedures of the first stage of the conventional technology: dosage of the initial graphite powder and binder-phenolic resin plastic varnish (for example, Bakelite), mixing, densification, thermal treatment, crushing, grinding, sieving, drying, dosage of grained graphite, dosage of the initial silver powder, obtaining of the silver salt solution, settling of salt, filtration, washing, drying of the cladded graphite powder, thermal treatment, obtaining of the graphite powder of particles cladded by silver. The second stage of the convectional technology starts by obtaining of the cladded graphite powder and finishes by annealing of the pressed blanks (Fig. 1)."

Jan 1, 2004

By Y. Ikeda

Typical electric appliances were dismantled into component pieces to study the recyclability of these discarded goods. Types and weight ratios of these component materials were investigated and characterized. The results showed that if they are dismantled properly, these goods could be classified into several groups of similar materials and/or structures, namely those consisting of single materials, metal-plastic combinations, metal-metal combinations and complex combinations of many different materials. By separating each combination into recyclable materials and isolating hazardous materials, it was found that the final waste for disposal could be reduced and the recycling efficiency could be improved markedly as compared to the conventional shredding method. The metal-metal combinations account for 60% by weight of the total metal contents in electric appliances, and therefore, it becomes important to segregate these metals. For the complex combinations, a process consisting of pyrolytic decomposition of plastic contaminants followed by smelting of the residue is proposed. It is anticipated that nearly zero-emission recycling of electric appliances will be achieved by applying this treatment process.

Jan 1, 1995

By T. Tamagawa

Vaporization of zinc and mixing of zinc vapor with CO-CO2 mixtures were studied experimentally to prepare Zn(g)-CO-CO2-Ar mixtures with desired composition for investigating the condensation behavior and efficiency of zinc vapor. The vaporization rate of zinc was generally constant under given conditions, and could be increased by raising the flow rate of the carrier gas, temperature and vaporization area. The Zn(g)-CO-CO,,-Ar mixtures were quenched by a water-cooling sampling tube for measuring the actual composition of the mixtures in the reactor. The oxidation extent of the zinc vapor in the CO-CO2 mixtures had relation to the CO2/CO ratios and the temperatures. Under current conditions, it was necessary to employ the CO2/CO ratio below 0.125 for mixing the zinc vapor with CO-CO2 mixtures without oxidation. In addition, the appearances and zinc contents of the condensed zinc on the sampling tube were also examined.

Jan 1, 2001

By Michael P. Heisel

Solinox is a physical scrubbing process capable of removing a number of noxious materials from off-gasses, especially SO2, hydrocarbons, halogens, heavy metals such as dust, etc. As these materials are dissolved physically, (not chemically bound), the solvent is absolutely stable and no by-products are formed in the scrubbing cycle. The process has? been installed in three plants up to now, treating from approximately 30 MMSCFD to approximately 100 MMSCFD. These installations are in a non ferrous metal smelting operation, in a cellulose factory, and in a roasting process.

Jan 1, 1992

By V. B. Chernyavsky, Ladokhin S. V.

Equipment and continuous casting technology for the production of small diameter copper rods and tubes are described. Industrial copper wastes, such as scrap and shavings, were used as the charge. An electron-beam installation for rod and tube production includes a crucible with an electromagnetic stirring system and a pouring hole in its bottom, a bottomless mold, .and a special cooling system, which includes an oil and water cooling devices. For the first time in the electron-beam technology, rods of 8 mm and 14 mm diameter mm tubes of 14 mm external diameter and 7 mm internal diameter were produced through continuous casting by pulling them out of the vacuum chamder into the atmosphere with depressurizing the vacuum chamber. The production capacity of a single strand continuous casting machine was 200 mm/tnin for rod casting and 150 mm/min for tube casting.

Jan 1, 2000

By Carlos Carnurri

A characterization of mechanical properties of fire refined copper has been done in order to link ductility with oxygen content. The results show four different copper mechanical behaviours as temperature increases, where the oxygen con- tent, as Cu20 segregated, has a deleterious effect on ductility. It is concluded that until 500 ppm oxygen content, the fire refined copper could be rolled without remelting for deoxidation. Also a subsequent cold rolling could be done without intermediate annealing.

Jan 1, 1994

By Klara Kodrikova, Vera Kasparkova, Michaela Uhlirova, Karel Kolomaznik

"Potentially hazardous wastes from leather industry (blue shavings) are processed into various biostimulators within two steps. The first step takes place at high pH (11-12) and hydrolyzation is implemented with potassium alkali, in the second step the pH is lowered to 9 with phosphoric acid after enzymatic dechromation occurs. The resulting hydrolyzates were analyzed in the sense of molecular weight distribution and tested as biostimulators on rape (Brassica napus). The hydrolyzates can be also directly used as universal NPK fertilizers. It has been proved that the nitrate content in the edible parts of tested vegetables (radish, lettuce, and cucumber) was approximately 200 times lower compared to the vegetables fertilized with an inorganic nitrogen fertilizer. The harvests of vegetables fertilized with the hydrolyzate and the inorganic nitrogen fertilizer were almost the same.IntroductionDuring processing raw hide into leather (tanning processes), only 20% of the collagen material is used for the final product. The remaining 80% ends up as waste, both tanned and non-tanned. Non-tanned waste such as calcimine can be used for production of artificial collagen casings for sausages, gelatine and also in pharmaceutical industry as collagen capsulates. Further processing and recycling of tanned leather waste (especially chrome shavings) is more complicated. Although many technologies producing various quality collagen hydrolyzates have been developed and tested in laboratories, few have been implemented on industrial scale. A promising turn came in the works of ERRC USDA [1,2]. They worked out an enzymatic dechromation technology (hydrolysis) and achieved a considerable decrease of the amount of relatively expensive proteolytic enzyme, which solved the difference between the quality and price of the final product. The American experience of enzymic hydrolysis were applied on industrial scale in the Czech Republic, where a plant was built with daily processing capacity of 3 tons of chrome shavings. The experience of real operation was published in [3] and the cooperation between the Czech Republic and USA partners resulted in a patent [4]. The main asset of the patent was the use of volatile organic bases in the hydrolysis process giving high quality and cheap hydrolyzates with low ash content."

Jan 1, 2008

By Shuai Wang, Gang-hua Fu, Lu Yang, Yu-feng Guo, Tao Jiang

The fluorine-bearing iron concentrate is one of the refractory raw materials for pelletization, which is mainly used in Baotou iron and steel company with lots of problems, such as narrow roasting temperature range and low compressive strength of products. According to its specific character, the effects of roasting temperature, time on the compressive strength and microstructure of pellets were researched. The results show that low melting substances formed during the roasting was the dominant reason of those problems. High melting substances were added in the roasting to investigate their effects on the roasting properties of fluorine-bearing iron concentrate pellets. Low melting substances were reduced when chromite was added. The compressive strength of products was 3100N/P when the 2% chromite was added at the roasting temperature of 1150 ºC, which was increased 700 N/P compared with the pellets without chromite, and the roasting temperature range was expanded by 170 ºC.

Jan 1, 2016

By Dengfu Chen, Yi Yang, Chunmei Chen, Mujun Long, Shikai Gong, Junhao Sheng, Tao Liu

The relationship between thermo-physical properties of petroleum coke and temperature is of importance for determining of the operating parameters during the calcining graphitization process. In this paper, the variations of thermo-physical properties of petroleum coke versus temperature were investigated, such as the DSC-Tg curve, the specific heat capacity, the thermal diffusion coefficient, the thermal conductivity, and so on. The thermal analysis curve of petroleum coke showed synchronous thermal hysteresis at higher heating rates, indicating that a larger heating rate will cause delay of thermal effects. The thermal diffusivity of petroleum coke decreased during the calcining process. With increasing temperature, coefficient of heat conductivity and specific volume heat of the petroleum coke increased with a decreasing variation rate. The research provides a database for the calcining graphitization process of petroleum coke.

Jan 1, 2015

By Lifeng Zhang, Zineb Benouahmane, Yaqiong Li

Experimental oxidation tests at high temperature (1000-1200 °C) on SiC samples have been respectively performed under wet and dry air atmosphere for different holding times. The thickness of thermally grown oxide was experimentally measured by DEKTAK Stylus Profilometry. The results showed that the oxidation rate was increased with temperature and holding time, corresponding to a passive oxidation regime which led to the formation of SiO2 layer. The sessile drop method was employed in order to measure the contact angles between Si and SiC at high temperature. Contact angle can be varied from 39.6° to 75.6° by controlling the atmosphere. The deoxidation of the oxide layer and infiltration of liquid silicon caused a decrease in the contact angle.

Jan 1, 2016

By B. M. Fisher

A process for making electrolytic copper of high quality from copper flotation concentrates is described. The concentrates are first slurried and then subjected to a high-temperature, high-pressure, oxidation-leaching operation under controlled conditions. The resulting slurry from the oxidation-leaching operation is cooled or flashed to atmospheric pressure and then subjected to a solids-liquid separation. The separated liquor, containing the recovered copper values, is cooled and then fed to an electrolytic deposition operation where metallic copper cathodes of high purity are produced. The spent electrolyte is then subjected to a sulfide treatment to precipitate the residual amounts of copper not deposited in the electrolytic cells. The precipitated copper sulfide is recovered and recycled in the form of a slurry to the initial stages of the process.

Jan 1, 1976

By Richard P. Roberts

This paper will discuss the methods for the cooling of aluminum melting furnace? dross .and their impact on the environment. Also discussed will be a case history of an AROS Dross Processor installation, which is designed to maximize the recovery of metal content of the dross in a manner which is not only environmentally cleaner, but which also prepares the output in such a way as to facilitate downstream processes. Handling of the discharged material will be discussed in regards to the recycling of the preserved metal content and deposition of the unusable-materials.

Jan 1, 1992

By David J. Krichten

A method of retrofitting air-fuel burners with oxy-fuel capability overcomes the potential problems associated with oxygen combustion in aluminum melting furnaces. The retrofit burner uses the existing combustion air connection, burner housing, and burner tile and replaces the gas tube with an oxy-gas burner. Maintaining a portion of the air flow to the burner reduces the potential for localized overheating. Proper design of the burner reduces NOx emissions by moderating the flame temperature with furnace gas recirculation. Economic analysis of using oxygen shows the benefits are increased productivity and reduced overall unit cost of melting. In practice, the melt rate in rotary furnaces increases by up to 50% and by up to 35% in reverberatory furnaces. Oxygen utilization reduces total melting cost by 112-314 cents per pound of aluminum melted.

Jan 1, 1997

By F. Kassabji

This publication presents the main experimental and theoretical results on the recovery of aluminum scrap (dross and Used Beverage Can) without use of any addition of fluxing salts. Dross and UBC&apos;s processing experiments have been conducted in a rotary plasma furnace operating in the transferred and non-transferred mode, using different plasma gases. The investigation involved the treatment of more than 100 kg of dross and other aluminum residues using plasma torches with less than 100 kW power. The experimental work showed that this process is .far more economical and kind to the environment than the conventional route using a salt flux. An equilibrium thermodynamic calculation at elevated temperature makes possible the prediction of by-products at various temperatures for different plasma gases.

Jan 1, 1994

By Alan Branham

The Mike deposit is a large, low grade, oxide, gold-copper system found at the intersection of two major faults that bound the Carlin Window, Eureka County, Nevada. Disseminated gold occurs within metamorphosed and hydrothermally altered silty limestone (Silurian-Devonian Roberts Mountains Formation), beneath 182 m (600 feet) of barren Tertiary sediments and tuffs. A supergene copper oxide blanket occurs beneath and locally overlaps the lower portion of the gold zone. Decalcification argillization, silicification, and brecciation are superimposed on earlier calcsilicate hornfels and marbles. Altered dikes and sills intrude the gold zone and are locally auriferous.

Jan 1, 1995