Search Documents

By Paul B. Queneau

U.S. plants solely devoted to recovering values from metal-rich wastes have established market niches based on one or more competitive advantages: superior process technology, access to key feedstocks, unique equipment, special knowledge of markets, and an appropriate exit for outfall water. Plant methodology, competitiveness, environmental factors, and economics are examined, with particular attention to feedstocks, technologies, products, and outputs.

Jan 1, 2003

By Torben L. Edens

Norddeutsche Affinerie is the largest copper producer in Europe. Two sites are in operation for the production of refined copper: primary copper production is located in Hamburg and secondary copper production in Lünen. A total of just under 560,000 tonnes of copper cathodes is produced annually at the two sites. Primary copper production using the flash smelter furnace has been in operation in Hamburg since 1972. Over the years, the capacity of the flash smelter has been increased in three expansion projects from 120,000 t to almost 500,000 t of anode copper p.a. The anode sector consisting of two anode furnaces and a 24 mould casting wheel still features just about the same equipment as in 1972. The paper describes the most important steps taken to optimise operation which have put NA in a position to cast meanwhile more than 500,000 t of anode copper annually with the two anode furnaces and 24 mould anode casting wheel.

Jan 1, 2006

By Norbert L. Piret

During smelting of copper, arsenic in the feed reports to a large extent to the gas phase and some enters the anode copper. From the gas phase it is transferred during wet gas cleaning directly, or indirectly after dust processing, to aqueous solution. During the electrorefining and anode slimes processing, the anode arsenic content is also transferred to aqueous solution. Technology for the efficient removal of arsenic from process streams and cleaning of aqueous effluents is well established. However, the arsenic-bearing products, which thereby are generated, can vary widely in consistency, quality and quantity, from large amounts of gypsum contaminated with water-soluble arsenic compounds to residues with high arsenic content ' or arsenic products. Arsenic management in a copper smelter not only is involved with the duty of compliance to the gaseous and aqueous emissions standards but also should have as objective the minimization of the generation of arsenic-bearing and, in general, heavy metal-bearing solid waste. The present paper outlines options and the associated economic aspects for minimization of arsenic-bearing solid waste generation, for improvement of the environmental compatibility of the residues to be deposited and for the .production of commerciable arsenic compounds under appropriate market conditions.

Jan 1, 1999

By Lucas Lopes da Costa

Bamboo fibers were characterized in terms of diameter distribution and tensile properties. Polyester matrix composites reinforced with these fibers were investigated for their flexural mechanical behavior. Specimens with up to 30% in volume of continuous and aligned bamboo fiber composites were bend-tested until fracture. The results showed an improvement in the composite strength and stiffness with the amount of bamboo fiber. A microstructure analysis by scanning electron microscopy revealed a reasonable adhesion between the fiber and the polyester matrix which justifies the improved mechanical properties of the composites.

Jan 1, 2010

By Ju Shao-hua

Although nowadays gold extraction methods are very abundant, none of them is satisfying, especially, in the field of heap leaching of low grade gold ore. The traditional heap leaching method of cyanide method plays an inglorious role of badly environmental pollution. In this paper, a bran-new and innoxious method of gold extraction system, metal-ammonium-chloride-ammonia (MACA), was proposed, and also analyzed both thermodynamically and practically. Thermodynamically, according to the principles of simultaneous chemical equilibrium and electronic charge neutrality, the thermodynamics of Au-NH4Cl-NH3-H2O system was studied by using the exponential computation method and through MATLAB programming, and the solid figure of its potential - c(NH4Cl) - c(NH4OH) was drawn. The results showed when the concentrate of ammonia is higher than 0.6 mol?L-1, fAu+/Au is only about -0.2 v. Practically, the leaching results of a cuprous gold ore showed that the extraction of gold can reach to 80% in this system. The preliminary results of reduction of the rich solution with copper and zinc powders showed that with deoxygenizing, the reduction effects were relatively good. These new findings and results have established a theoretical and practical base for developing a new process for heap leaching of low grade gold ores in this system. And the new process owns a series of merits such as, non-cyanogens, nontoxic, broader applicability.

Jan 1, 2006

By Cesimiro Fabian

The crystallite size of copper electrodeposits was determined by X-Ray powder diffraction analysis using a General Area Detector Diffraction Solution (GADDS) diffractometer. Crystallite size was calculated for copper thin films which were deposited on a 316 stainless steel rotating cylinder electrode (RCE) in the presence and absence of additive ?A?. The crystallite size was calculated from a corrected full width at half maximum (FWHM) of the [110] peak profile using the Scherrer equation. The test of significant difference on crystallite size was derived using Kruskal-Wallis method. It was found that in the absence of the additive the median crystallite size was 426, which decreased to 364 in the presence of the additive. As the additive degraded, the crystallite size increased to a size similar to that observed in the absence of additive.

Jan 1, 2003

By Fernando Guevara

Many smelting and slag-cleaning furnaces operate with cooling systems designed to freeze a slag layer over the refractory to protect it. The fluid flow and heat transfer conditions associated with the freeze layer and mushy zones are poorly understood. These phenomena were simulated with a small-scale room temperature, 2-dimensional model, using an aqueous solution of calcium chloride to simulate the slag. Reasonable similarity with conditions encountered with copper and nickel smelting systems was achieved (Pr 50 and Ra 108, in the laminar-turbulent transition). Measurements of the freeze layer development and velocities were made with the Particle Image Velocimetry (PIV) technique. Direct Numerical Simulations (DNS) were also made of the unsteady fluid flow and heat transfer problem. It was found that the solidification process is well described using an improved model for high molecular viscosity in the mushy zone. Solid front growth, isothermal profiles, velocity profiles and heat transfer through the walls showed good agreement between the PIV and DNS results. Experimental and numerical velocity profiles close to the freeze layer show a parabolic behaviour in the vertical velocity profile which is completely different from the calculation of heat transfer using a sharp interface model. The reason for this is attributed to the effects of the mushy zone with a high viscosity and high shear stresses acting on that area.

Jan 1, 2006

By D. Valic

In 1997, 9.2 million tonnes of mined, recoverable copper was produced, of which, 1.8 million tonnes or 19.4% was produced by leaching, solvent extraction and electrowinning. The amount of copper produced by this method grew faster than those attained from concentrate smelting, signifying the growing importance of this low-cost production method. Statistical experimental design, unlike traditional approaches, allows for proper distribution of experiments within the boundaries of factors being studied such that the number of experiments required to develop a sound relationship between the factors and a response is minimized. In the past, very little use has been made of statistical experimental design in copper electrowinning studies. Traditional one- variable-at-a-time approaches are widely employed for this purpose. The present study employs a factorial experimental design to relate current efficiency with current density (180 and 300 A/m2), copper concentration (25 and 65 gL), and temperature (40 and 60 °C). Pure synthetic electrolyte with a constant acid concentration of 180 g/L was used throughout the study. The designed study produced a linear relationship where the independent variables of current density, copper concentration, and temperature, and their interactions, were found statistically significant. It was shown that current efficiency could not solely be used as a predictor of copper cathode quality. The quality of the deposit is difficult to be incorporated into a model or relation. It was determined that other measures, such as cathode morphology and crystal structure should be considered. This was done through XRD and SEM analysis.

Jan 1, 1999

By Ana E. Bohé, Georgina De Micco, Gastón G. Fouga

"In this work the reaction between several manganese oxides and chlorine is investigated in the range of temperatures between 650 and 950ºC. The reaction path for the chlorination of MnO is established, which involves recrystallization of high valence manganese oxides (Mn3O4 and Mn2O3) followed by its chlorination. For this reason, to understand the reaction of MnO, the chlorination of Mn3O4 and Mn2O3 has also been studied. The starting temperature for the reaction of these oxides is determined by non isothermal thermogravimetric measurements. The effect of temperature is analyzed, under our experimental conditions the rate of reaction is mass transfer controlled. The activation energy for the volatilization of manganese chloride is obtained which is in good agreement with volatilization enthalpy of MnCl2.IntroductionMany oxide ores which have manganese in their composition undergo chlorination processes during the extraction of refractory metals such as Ti, Hf and Nb. Although several works related with chlorination of manganese oxides were reported, there is no information about the kinetics or mechanism of the manganese oxide chlorination reactions. Okahara et al. studied the chlorination of manganese oxides and established that they react easily above 250ºC. Furthermore, they observed that chlorination of high order oxides is more difficult when there is not a reducing agent [1]. Ivashentsev studied the chlorination of manganese oxides using Cl2(g), CO(g) + Cl2(g) and COCl2(g). He established that the reaction of MnO started at 130ºC with formation of MnCl2(s), he also observed recrystallization of manganese sexquioxide [2]. Finally, the chlorination of manganese nodules from the ocean was studied by Murthy and Reddy [3] with the aim of obtaining valuable metals such as Mn, Co, Ni and Cu. They studied the influence of several parameters like temperature, carbon percentage, particle size and chlorine flow rate in the extraction process."

Jan 1, 2008

By Dachun Liu, Wenlong Jiang, Baoqiang Xu, Yongnian Dai, Bin Yang

"In the traditional method for refining of indium, glycerin-KI and glycerin-NH4Cl are used as electrolytes to remove Cd and Tl by electrolytic refining, which produces In with a purity of 99.995%. Large quantities of polluted industrial waste water are the result. It is calculated that the saturated vapor pressure of Cd and Tl are between 1-200 Pa, which is much larger than the vapor pressure of In. Thus, the study of removing Cd and Tl was carried out over the temperature range between 700-950 °C and pressures between 1-15 Pa. After vacuum distillation the contents of Cd and Tl in crude indium could sharply fall below 1 ppm..IntroductionIndium is a is a pale blue and silver white metal, and has high ductility [1-2]. Pure indium is generally used as a raw material to produce semiconductor compounds, fluorescent material and ITO targets [3]. Sublimation, zone melting and electrolytic refining are major methods to produce pure indium from crude indium. Electrolytic refining is the main method to product pure indium at present. High productive efficiency, simplicity of operation and short cycle of production are major advantages. However, glycerin-KI and glycerin-NH4Cl are used to remove Cd and Tl in electrolysis method. Large quantities of polluted industrial waste water are the result[4]."

Jan 1, 2012

By Tuula Mäkinen

In 1959 Outokumpu started up an integrated nickel smelter and refinery at Harjavalta. The flash smelting ? Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes by leaching and electrowinning. In 1995 the production capacity was increased from 17 000 mtpa to 52 000 mtpa, based on the Direct Outokumpu Nickel Smelting Process. The additional refinery capacity is based on hydrogen pressure reduction, producing nickel powder and briquettes. The smelting operation is currently part of Boliden Group and the nickel refinery part of OM Group. In the DON technology, high-grade nickel matte with low iron content is produced in the flash smelting furnace directly without subsequent converting. The metal values in the smelting slag are recovered in an electric furnace as an iron containing Ni-matte. The mattes produced differ from the conventional nickel mattes in many respects, and therefore focused R&D efforts have been made in order to cope with their melting points, fluidities and settling properties. When developing and operating metallurgical processes it is crucial to manage and control the characteristics of the products as well as by-products generated in different steps of the process chain. The low melting points of the high-grade nickel mattes produced in the DON furnace, particularly those low in copper, have pointed out challenges in the furnace design, in particular in the hearth and its thermal engineering. Also key issues of the DON technology are smelting of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of PGM`s and cobalt. These factors can be affected by a proper selection of the process concept, and the operational conditions in the processing vessels. This paper deals with the experience of the DON technology gained over the first ten years of operation, including the significant environmental impacts. Selected results of the thermo-dynamic modelling of DON and EF mattes and high-magnesia slags are reviewed, with the reference to the mattes produced. Also the design principles of the FSF and EF will be discussed.

Jan 1, 2006

By Michal Rzyman, Nakamura Takashi, Shibata Etsuro, Grabda Mariusz, Oleszek-Kudlak Sylwia

"Thermodynamic considerations indicate that heavy metal oxides should easily react with HBr, the main gaseous product from the thermal decomposition of tetrabromobisphenol A (TBBPA), forming low boiling point metallic bromides suitable for volatile separation. Mechanisms and kinetics of the bromination reactions must be well recognized prior to developing of a new treatment for the simultaneous recycling of plastic waste containing brominated flame retardants (BFRs) and metal oxides (printed circuit boards, automotive shredder residue, plating sludge, metallurgical dusts). In this work, a differential scanning calorimeter and laboratory-scale furnace were used to investigate the possibility and conditions of the bromination of ZnO by product of thermal decomposition of TBBPA. The formed solid, condensed and gaseous products were analyzed by X-ray diffraction analysis, electron probe microanalysis, inductively coupled plasma analysis, ion chromatography and gas chromatography coupled with mass spectrometry. Introduction Tetrabromobisphenol A (TBBPA) is the largest volume brominated flame retardant (BFR) in production today and is used in more than 70% of the world’s electronic and electric (E&E) appliances [1]. The growth in the production of E&E products and the fact they become obsolete so quickly cause significant problems in the safe disposal and recycling of the electrical and electric waste (E-waste) and other BFR-containing waste [2]. Among various treatment processes, thermal methods are most useful since they allow the recycling and recovery of both the organic and inorganic fractions of the waste. However, incineration of the BFR-containing wastes results in the emission of hazardous organobromine compounds, while the main portion of bromine released from decomposed BFRs is present in flue gas as hydrogen bromide (HBr) [3]. HBr, which is known to damage incineration systems, seems to be a very effective bromination agent for many metallic oxides present in waste. The concept of this study is to take advantage this of its property."

Jan 1, 2008

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides (MA) can be incorporated for use as a transmutation fuel. This study involves characterization of precursor powders and pellets to be inserted into the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U80Pu20)O1.98, and two compositions of MA-MOX with oxygen to metal ratios (O/M) of (U75Pu20Am3Np2)O1.98 and (U75Pu20Am3Np2)O1.95. The precursor powders, which consisted of, highly enriched uranium oxide, HEUO2, depleted uranium oxide, DUO2, neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a field emission gun scanning electron microscope (FEG-SEM) for particle morphology, size, and size distribution prior to pellet production.IntroductionThe Global Nuclear Energy Partnership (GNEP) was created in order for “fuel-cycle supplier” nations to provide assured supplies of nuclear fuel to “fuel-cycle customer” nations. The customer nations would utilize the fuel for electricity generation and subsequently return it to the supplier nation after it is spent. This spent fuel would then be reprocessed by the supplier nation in order to recycle the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials would also be strictly controlled through the International Atomic Energy Agency. One of the thrust areas for the GNEP program is the development of these actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3]."

Jan 1, 2008

By Kotaro Ogura

"Ethylene has been produced in aqueous solution from CO2 by the electrochemical reduction driven by a natural energy. This process is useful for storing a large amount of the natural energy. In the closed system, the conversion efficiency of CO2 is almost 100%, and the maximum selectivity for the formation of ethylene is more than 70%. On the other hand, the current efficiency for the competitive reduction of water is less than 10%. The electrolysis is practicable under such special conditions as three-phase interface consisting of gas, solution and metal, concentrated solution of potassium halide, low pH and copper or copper halide-confined metal electrode. These requirements are thoroughly examined, and the grounds to reply upon are revealed. A series of chemical apparatuses including an electrolytic cell in a large scale are designed for the ethylene production, which allow us continuously to supply raw CO2 and to extract the product.IntroductionIn connection with the depletion of the petroleum reserve, much attention has been paid to the utilization of natural energies such as sunlight, wind force and waves. However, these energies are always changeable, and some means of storing them are necessary for the common use. In general, natural energies are transformed to the electric energy at the time of utilization, but the electricity is not very storable. This is one of the reasons why the application of natural energy is not so expanded. On the other hand, the storing of natural energy by plants is very skilful. In the photosynthesis, solar energy is transformed to chemical energy by fixing carbon dioxide."

Jan 1, 2009

By Fathi Habashi

"Davy, Faraday, and Bunsen laid the foundation of electrometallurgy which had a· great impact on other areas of metallurgy. Electrometallurgy is presently dominated by the production of aluminum, the electrorefining of copper, and the electrowinning of zinc. It has also been successful in the electrowinning of copper from solutions obtained by leaching-solvent extraction. Electrowinning processes, however, are capital intensive. Improvement of the present technology should be intensely investigated especially when it is expected that such processes will increase greatly as a result of a shift from certain pyrometallurgical processes to pressure hydro metallurgy.INTRODUCTIONPyrometallurgy was used for thousands of years to produce copper and iron from their oxide ores!). Today it is still the only route to produce iron and steel and it is certain that it will remain so for many decades to come because pyrometallurgy is most suitable for the treatment of high grade oxide ores. Even when high grade iron ores are exhausted, it is possible to beneficiate the low-grade ores and produce pellets suitable for reduction in the blast furnace, which is a very efficient reactor, being a heat exchanger as well. Hydrometallurgy on the other hand can be traced to the time of alchemists in the Middle Ages when they were seeking to transmute base metals into gold, and thus were able to prepare many acids and bases which are the essential leaching agents."

Jan 1, 1997

By J. Fraser Forbes

"The meaning of the term ""process control"" has evolved significantly since its widespread use began in the manufacturing industries in the 1940s. Further, the scope of process control applications has drastically increased both in terms of the breadth of industries using process automation technologies and the vertical integration of these technologies within a single industry. This evolution and integration of process control technologies within the manufacturing industries has proceeded to such an extent that process automation is an integral part of modern business practices.This paper will examine the current status of process control technology from simple process regulation through process performance optimization to business planning. Each layer of the operations automation hierarchy will be discussed both in. terms of the current state-of-the-art and the directions in which these technologies are evolving. The key tools and tasks necessary for success at every level of the automation hierarchy will be introduced. Finally, the critical challenges that must be faced in accomplishing the goal of complete Computer Integrated Manufacturing (CIM) will be described.Finally, although this paper addresses issues of practical importance to any manufacturing company, the discussions will be framed in terms of the particular challenges facing and the opportunities available within the materials manufacturing industries."

Jan 1, 2000

By Joseph Sofra

It has become increasingly evident that sustainable metals production in the 21st century requires producers to balance the needs of cost effective, high value production with that of responsible plant operation. This is becoming more difficult as lower grade and more complex feed materials, including recycled scrap and residues, are being processed to reduce production costs and decrease exposure to primary metal market fluctuations. One particular facet of the metals industry facing these challenges in the 21st century are copper producers, The recent steady decline in the copper price has seen the industry cut expenditure, tighten control on income streams and focus on high returns on capital investment. For these reasons copper producers are looking towards flexible technologies that can deliver high value products, with minimal environmental impact at low capital and low sustainable operating costs. Ausmelt's Top Submerged Lancing (TSL) technology for copper production is a low cost, proven technology for the processing of both primary and secondary copper materials. Both the smelting and converting operations introduce significant advantages in environmental performance, improved process efficiencies and high rates of metal recovery, Ausmelt has made significant gains in the past 4 years in establishing a strong market position for its copper technology, New installations in China, South Africa and India as well as existing operations in Zimbabwe and China have demonstrated its effectiveness. This paper reviews the application of Ausmelt Technology for both smelting and converting of primary and secondary sources, It discusses Ausmelt's design and implementation philosophy, and how this philosophy meshes with the needs of the end user.

Jan 1, 2003

By J. T. Stanley

The identification of crystal phases and crystal chemistry can be critical to understanding the mechanisms of waste material interaction with native soils. Understanding these mechanisms can suggest correct methods for remediation and treatment. A program is outlined and examples are given of the development of effective techniques for rapid phase identification of environmental samples using electron microscopy. The program concentrates on the development of integrated object oriented software to aid rapid searching of online databases and rapid simulation of potential crystal diffraction patterns. Examples come from dried sludge taken from a former hard-chrome plating facility.

Jan 1, 1993

By Shunli Zhang

Metals recovery from electronic scrap by physical separation may provide an alternative to the current recycling approach, through which halogenated flame retardants can result in hazardous dibenzo-p-dioxins and dibenzo-furans. On the basis of a complete sink-float analysis of personal computer and printed circuit board scrap, and in view of the advantages of dry processes for electronic scrap recycling by mechanical separation, air table separation is prioritized in an attempt to separate metals from plastics and glass involved. In the present paper, theoretical and practical considerations of air table separation have been detailed. It has been shown that air table separation is effective for recovering copper and precious metals from this specific waste stream. With the feed rate of 60 kg per hour, the combined grade and recovery of copper, gold, and silver attainable for the two heavy products produced by the air table used in the present study was shown in the following table:

Jan 1, 1998

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.