Search Documents

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly. subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fumeless fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By I. Ohnaka

Although many works have been reported on the semisolid casting, the mold filling behavior of semi-solid alloys has not been so well understood. This paper compares the physical and numerical simulation results on the mold filling behavior. Physical simulation was performed by using solid-water mixture. The numerical simulation was made under the assumption of one phase flow with an effective viscosity. It was found that the solid particles stabilize the flow greatly if the kaction solid exceeds about 0.4, because viscosity increases greatly. The overall flow behavior can be estimated by the numerical simulation. Interesting flow behavior was also found which can not be observed in the case of one phase flow and which is difficult to simulate by the one phase flow assumption.

Jan 1, 1997

By Michael J. Nicol

This paper summarizes some of the results of a study of the reactions involved in the Caron leaching process and identifies the roles of the major dissolved species in the kinetics of dissolution of iron alloy particles formed during reductive roasting. Using rotating disk electrodes and synthetic leach solutions, the reduction of water with the evolution of hydrogen was found not to occur on a dissolving iron surface under typical leach conditions. It has been established that the oxidative dissolution is governed primarily by a reaction involving reduction of Co(III) to Co(II) ions. The reduction of oxygen was also found to make a significant but largely indirect contribution to the kinetics of the dissolution process. The dissolution rates of various iron-nickel-cobalt-copper alloys which simulate the dissolving alloy particles in a Caron plant were measured in synthetic leach solutions under aerobic and anaerobic conditions. The initial dissolution rates of iron, nickel and the iron alloys were found to increase in the presence of thiosulphate, whereas the thiosulphate had a negative effect on the dissolution rates of cobalt and copper. It is shown that the eventual passivation of the iron occurs sooner in solutions rich in Co(II) ions. Whilst these conditions are present in the quench slurry, on-site measurements have shown that due to the very high concentration of reduced dissolved species, passivation does not occur until the slurry is strongly aerated. In the light of these fundamental findings, options for optimizing the rate of dissolution and minimizing the extent of passivation of the iron and iron alloys are discussed. Keywords: Ammonia, leaching, alloy, kinetics, passivation.

Jan 1, 2004

By Marcello M. Veiga

Informal gold mining operations in the Amazon emit about 100 tonnes of mercury annually because of poor amalgamation practice. Lack of information and the complexity of mercury transformations hinder effective action to prevent such pollution and/or monitor its extent. In the past, mathematical equations have been formulated to deal with the correlation of natural variables and mercury in biota but often, the error range is too great to provide useful models. Projection of physico-chemical variations in an environment subjected to mercury emissions onto the extent of bioaccumulation is fraught with many uncertainties and unknowns such as internal correlations between variables and the site-specific nature of biota contamination. Often assumptions about closed systems are invalid when applied to natural environments. This work presents a heuristic approach to this problem in which amalgamation methods and natural variables are dealt with using an IF-THEN rule-based system that concludes about levels of emission and risk of bioaccumulation. The system is able to handle uncertain or vague data and yet still provide useful output. Belief in mercury oxidation or dangerous conditions are examined using Fuzzy Logic techniques and Inference Equations. These belief levels are derived from thermodynamic equilibrium data together with field observations of natural variables. This procedure can reduce the need for sophisticated analytical equipment and can provide information and diagnosis to non-technical people.

Jan 1, 1994

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for four years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace's hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1997

By J. H. Puffer

The copper mineralization of the Mesozoic Passaic Formation of New Jersey is typical of copper deposits in eastern North American Mesozoic sediments. Most such deposits are located at the base of the first of several basalt flows that are interbedded with continental, red-bed sediments. The copper mineralization is similar in most respects to that of the Keweenawan Basalts of the Lake Superior area. The first basaltic flow units of the eastern North American Mesozoic basins, and the Keweenawan Basalts, are continental quartz tholeiites of similar chemical composition and copper contents. The copper minerals and associated zeolite facies metamorphic mineral assemblages of these two rock units are also approximately the same. Stoiber and Davidson (1959) suggested that Keweenawan copper was mobilized and concentrated during metamorphism. The evidence pertaining to the Mesozoic copper deposits of New Jersey is consistent with such an interpretation and also with DeVore's (1955) suggestion that ore fluids commonly arise as a result of the mobility of metals under metamorphic conditions. There is additional evidence that final metamorphic concentration of Mesozoic copper was preceded by an initial stage of hydrothermal precipitation related to fluids emitted by basaltic magma.

Jan 1, 1987

By James W. Evans, Brian R. Wildey

"Carbon has been the principal reducing agent in producing metals for centuries. Carbon is an inexpensive reducing agent, but also an effective one, as any undergraduate who knows her Ellingham diagrams is aware. Even in the production of aluminum, an electrolytic process, carbon consumed at the anodes serves to reduce the voltage of the Hall-Héroult cell. The interest in reducing the amount of anthropogenic CO2 has led to this examination of whether a switch to hydrogen as a major reductant is feasible and economic. The main source of hydrogen is natural gas and its production entails the generation of CO2; however, that CO2 is more easily captured than, say, the CO2 leaving an iron blast furnace. Calculations and speculations lead to conclusions about whether there is significant benefit to be obtained from such a radical change in our way of producing metals and the approximate cost of such change.IntroductionThe 1991 paper by Forrest and Szekely1 was one of the first to examine the impact of CO2 emissions from the primary metals industries on global climate change. These authors compared data from 1968 and 1985 and reported a drop in carbon emissions from 115.8 million tons to 65.6Mt over this period, the latter figure representing approximately 1% of the world’s greenhouse gas emissions. Much of this reduction was due to a drop in steel output (with carbon emissions increasing within the aluminum and copper industries in this period) but some were due to technological changes such as increased use of continuous casting. A more recent paper on CO2 emissions, focused on the steel industry in Japan, is that of Ariyama and Sato2. These authors report CO2 emissions of 182.4Mt from the Japanese steel, industry in 2003, down from 194.8Mt in 1990. The former represents 14% of the GHG emissions for Japan in 2003. Much of this emission is from ironmaking and the authors break these emissions down into"

Jan 1, 2008

By S. Viswanathan, A. S. Sabau

"Dimensional changes between a pattern die and its corresponding investment casting part occur as a result of complex phenomena such as thermal expansion/contraction and hot deformation (elastic, plastic, and creep) during the processing of the pattern material (wax), mold material (shell) and solidifying alloy. Determining the pattern tooling dimensions is crucial to the dimensional control of the investment casting process. To date, computational methodologies have not been applied to the prediction of dimensional changes in investment castings.This paper deals with the evaluation of wax pattern dimensions, which is one important factor in determining pattern tooling dimensions in investment casting. Cerita 29-51, an industrial wax, is considered in this study. The wax pattern dimensions are determined by considering its thermo physical and thermomechanical properties, restraint of geometrical features by the metal die, and process parameters such as dwell time, platen temperature, injection pressure, and injection temperature.IntroductionThe investment casting process involves making a disposable wax pattern by injecting wax into a metal mold, building a ceramic shell mold around the wax pattern by the application of a series of ceramic coatings to the wax pattern, dewaxing the ceramic shell mold, and casting the alloy into the shell mold. Dimensional changes between the pattern tooling and its corresponding cast part occur as a result of thermal expansion, shrinkage, hot deformation, and creep of the pattern .material (wax), mold material (shell), and solidifying alloy during the processing [1]."

Jan 1, 2001

By Rak-Jun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEOs. Efficient blue light-emitting diodes (LEOs) were fabricated using InGaN/GaN triangular MQWs. The LEOs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEOs at 20 rnA and 20 "C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LEO, but decreased substantially in the rectangular one.

Jan 1, 2003

By G. S. Gupta

To predict the iron oxide concentration a mass transfer model has been developed for an Induction Smelting Process (ISP) in which self-fluxed composite pellets (made of iron ore, brown coal and lime) are melted in a single phase induction furnace in conjunction with top blown oxygen. Transient mass balance equation with complex boundary conditions has been worked out by adopting a relatively new approach known as the cell model approach. These equations have been solved numerically using finite difference technique to obtain the iron oxide concentration profile in the ISP. Numerical and experimental results obtained for iron oxide concentration show a reasonable agreement with each other.

Jan 1, 1991

By Steven R. Pittman, Colin McCullough, Peter Galuska

"Traditionally Continuous Fiber Aluminum Matrix Composites have been fabricated using high strength fibers and high strength matrices, often commercial alloys, with the goal of producing high strength composites. However the specific role of the choice of matrix alloy on composite properties has not been well established. One way to control composite tensile strength is to use coatings to introduce a low strength interface between fiber and matrix which tends to reduce the importance of the matrix selection, but unfortunately renders the transverse strength unacceptably low. Thus using a system with strong bonding between fiber and matrix is desirable, such as an alumina fiber / aluminum alloy matrix system. In this case the transverse strength is a strong function of the matrix strength. However the longitudinal strength then depends largely on the characteristics of the matrix. The important role of the matrix is discussed using examples of alumina fibers in various aluminum alloy matrices. The key attributes are matrix constituent phases, alloy chemistry, alloy reactivity with the fiber, and matrix strength. From the understanding developed in these systems a set of design rules may be established for selecting an optimum matrix. IntroductionAluminum matrix composites (AMC's) reinforced with continuous fibers offer very attractive property gains over AI alloys, such as strength, stiffness, and fatigue resistance. These gains are magnified when specific mechanical properties are compared which make them attractive candidates for replacing steel, nickel, titanium and aluminum alloy parts in weight critical applications (1). Many systems have been tried in the past; B/AI, C/AI, SiC/AI, Si-Ti-C-O/AI and AI203/AI. Technically B/AI was a very good system but was expensive in regard to both fiber cost and fabrication and SiC/AI and C/AI systems are still plagued with reactivity problems. The Si-Ti-C-O/AI appears to be a good strength system but with lower stiffness. Until recently, the AI203/AI was a low strength system, in part due to a lack of a high strength fiber. Recently 3M introduced a high strength AI203 fiber - Nextel™ 610, which leads to high strength composites (1,2) and may also be both low cost and also compatible with less expensive casting approaches for fabrication."

Jan 1, 1996

By Tor Lindstad

Specific C02-emissions are given for the production of silicon-metal, ferrosilicon, ferromanganese and silicomanganese. Emissions taken into account come from reduction materials, from coke production and generation of electric energy. C02-emissions can be abated by direct and by indirect methods. A direct method is to replace fossil carbon as reduction material wholly or partially by endogenous carbon (biocarbon, charcoal). Another possibility is to produce metals by electrolysis instead of the present electric smelting furnace. Indirectly CO2-emissions can be reduced by energy recovery, thus saving coal, oil or natural gas for heat generation. Some reduction in global C02-emissions can be obtained by giving credit for the use of silica dust partially replacing cement in concrete. In addition to give an overview of possible methods, costs will be discussed.

Jan 1, 1999

"Depletion of known ore reserves and increased demand for precious metals have caused a revolution in biohydrometallurgical processing technology for gold recovery. Known ore deposits and future discoveries are most likely to be lower grade sulfide ores that can be difficult to recover with current leaching technology. Future metal recovery operations will increasingly use bio-oxidation techniques.Bacteria are an integral part of mineral cycling and mineral transformation in nature. Although biological processes are recognized as part of the mineralization and oxidation reactions in some ore deposits, they have only recently been applied to enhancing metal recovery in hydrometallurgical procedures. This paper explores the traditional metallurgical application of biological leaching and oxidation reactions and reviews the complete range of bacteria available for metal recovery systems. Pre-treatment of ores with bacteria improves metal recoveries in tank leaching systems and shows promise for heap leaching methods.IntroductionThere is no longer any question that bacteria playa natural role in the on-going transformation of some ore deposits (1,2). As applied to sulfide ores, a few strains have been specifically identified that exhibit a natural leaching potential (3). These bacteria can be isolated from waters and soils in old mining districts where they contribute to continuing leaching and pollution problems in acid drainage and heavy metal solubilization. Sulfur and iron bacteria as well as many heterotrophic strains have also been found in ore deposits and sedimentary rocks at depths up to 2000 meters (4). Their presence in both ore deposits and processed ores shows the microbial association with natural leaching and the potential role that bacteria can play in the development of new leaching technology."

Jan 1, 1988

By N. El-Kaddah, A. D. Patel, T. T. Natarajan

The phenomenon of particle migration in a conducting fluid under an applied electromagnetic force field finds its application in selective sorting of minerals and more recently in the removal of inclusion from molten metal. This paper deals with the analysis of the expulsion force and the flow around a spherical particle in crossed uniform electric and magnetic fields in .infinite and in confined medium. Analytical solutions will be presented for the electrk and magnetic fields as well as the induced flow at the limit of zero Hartmann number. The flow around the particle was investigated numerically at low and high values of Hartmann number. It will be shown the magnetic field has almost no effect on the velocity field when Hartmann number is less than 1.0. At higher Hartmann numbers the damping effect of the magnetic field was pronounced in the direction of the applied current. It is concluded that Hartmann number has little effect on the net force on the sphere particle.

Jan 1, 1999

By S. Illendula, B. Q. Li, R. A. Mirshams

"An integrated mathematical model is developed to represent the thermomechanical behavior of the materials and microstructure evolution during metal forging. The model development is based on the finite element solution of the thermoviscoplastic deformation of metals coupled with the internal state variable model describing the microstructure evolution involving work hardening, recovery, recrystallization and grain size distribution. The procedures for the integration of the microstructure model into the macro finite element model are described. Computed results for both macro and micro phenomena during metal forging, such thermomechanical deformation such as velocity field and effective strain rate and materials characteristics such as distribution of grain size and recrystallization volume fraction, are presented.1. IntroductionThermomechanical behavior and material microstructural evolution are two critical, interrelated aspects associated with metal workpiece undergoing large plastic deformations such as encountered in forging processes. In much of the modeling work up to date, these two aspects have been addressed separately. Die designs and forging processes are investigated using finite element based thermomechanical models while material dynamics during forging is studied, more often than not, as a separate subject. For many industrial applications, especially those involving novel, light and high strength materials, it is critical to combine these two aspects into a single, integrated model so that materials dynamics and thermomechanical deformation during forging processes can be considered simultaneously [1], thereby providing required information for intelligent process design and optimal process control."

Jan 1, 1998

By M. K. Patel, K. A. Pericleous, M. Molaei

"The future trading of carbon credits and increased financial cost necessitates substantial cuts in incidental C02 emissions in the production of metals (iron, steel, aluminum, zinc, lead). Although greener methods of production are being developed, in the short term the use of point-source C02 extraction using existing technology remains attractive. Accelerated natural carbonation, in a fluidized bed is a feasible technological route investigated in this research. CFD modelling has been used to study the efficiency of C02 capture in a fluidized bed reactor containing a CaO solid sorbent. A Lagrangian/Eulerian scheme describes describe CaO particle trajectories and exchange of mass, momentum and energy with the carrier gas, with a typical off-gas composition. Different reactor geometries are considered (with uniform, stepped and gradually expanding cross-section), to maximize conversion for a given particle loading and size distribution (100-200 microns). Removal efficiencies of up to 80% are demonstrated, making this a viable process.IntroductionBased on Intergovernmental Panel on Climate Change (IPCC) reports, the major cause of climate change and global warming is due to a high level of C02 concentration in the atmosphere resulting from fossil fuel combustion, particularly in coal-fired power plants [1]. Carbon capture and storage is therefore the most important action proposed to reduce C02 from combustion flue gases. In this process, carbon dioxide is captured and may then be regenerated as pure C02 and conducted to a permanent storage, or simply stored as a solid carbonate [2]. Capture and storage of C02 has an economic penalty and the main cost of this penalty is associated with the capture plant. Capturing C02 with a lime-based solid sorbent (CaO) is a very promising technique, due to the low cost and the wide availability of the reactant. In this process, the CaO reacts with C02 based on the following reaction in a reactor called a Carbonator:"

Jan 1, 2012

By Günter Petzow, Hans Leo Lukas, Hans Jürgen Seifert

"The CALPHAD method (CALculation of PHAse Diagrams) has been extensively developed in the last 25 years and became a useful tool in materials science. Thermodynamic descriptions for the functions of state of unary, binary and ternary phases are derived by the optimization of phase diagrams. These functions are stored in computerized thermochemical databases and can be combined to extrapolate to multi component systems. Depending on special demand, the actually most advantagous presentations of the calculated results can be chosen: tables or in a clear graphical form as phase diagrams, phase amount diagrams or volatility diagrams. The method will be desribed by the system Ti-Si-C-N-O including the ceramic subsystem Si3N4-SiC-TiCi,N1_1,-C-N-O which is very important for the development of ceramic composites. The calculations give the thermodynamic stabilities of the condensed phases as function of temperature, concentration and partial pressure of different gas species. Adjusting the sintering conditions to these results the formation of unfavourable compounds or liquid phases can be suppressed.IntroductionThe CALculation of PHAse Diagrams (CALPHAD-method) of multicomponent systems provides the possibility to plan experiments very efficiently and avoid the experimental trial and error approach for the development of materials. The main problem for best use of calculated results is their interpretation with regard to the specific applications under consideration. Tables give the exact quantitative data for the treated phenomena. However, most important to make best use of these thermodynamic data is their graphical representation especially designed for the solution of specific problems, scientific as well as application oriented. Only well chosen graphical representations support a comprehensive understanding of the thermodynamic interrelationships and the transfer to the problem."

Jan 1, 1996

By James Cornwell, John A. Elton

"Thermionic induced reactions and radiation resonance catalysis of aluminum and aluminum oxide materials exposed to microwaves and triboemissions will be described and explained from both a fundamental and practical level. Magnetron operation at distinct operating conditions that generates both plasmon and triboemissive radiation will be explained and the resulting tribochemical and radiation resonance catalytic reactions between aluminum, aluminum oxide, water and graphite will be delineated. The generation of hydrogen from these materials using triboemissive radiation and microwaves will be described, and the application of this methodology for hydrogen based technologies will be discussed.IntroductionProtective Systems Directed Energy RadiationProtective Systems, Inc, has developed a new radiation device called the EMR (Electromagnetic Resonator) that has unique characteristics that separates it from traditional microwave and rf radiation devices. The radiation from the EMR device is generated using a modified electronresonance magnetron with proprietary filters and operating characteristics.Electronic Device Shutoff. When electronic devices such as cell phones, computers, and other IC based electronics are placed within the EMR radiation, these devices become non-functional as long as the EMR beam is active. Upon removal of the EMR radiation the devices either become operational again or become operational after a cold start. The devices are not damaged by the irradiation.Faraday Cage Interaction Effect. When any of the above electronic devices are placed in a Faraday cage and activated within the Faraday cage without EMR radiation, they operate normally. However, these devices will still be rendered inoperative when an EMR beam generated outside the Faraday cage is directed at the electronic."

Jan 1, 2010

By Torn H. Okabe

A fundamental study was conducted with the purpose of establishing an environmentally sound recovery process for recycling of valuable metals, by combining scraps containing such metals. As an example, direct extraction and recovery of neodymium (Nd) in magnet scraps was investigated by utilizing liquid metal as an extraction medium. It was found that liquid magnesium (Mg) is a suitable extraction medium and can extract Nd from iron alloys with high efficiency at around 1100 K. The newly developed extraction apparatus for Nd is a mechanically simple and static device without moving parts, where the Mg extraction medium circulates due to differences in the temperature inside the reaction vessel. This developed device can simultaneously accomplish continuous extraction of metal Nd from scraps, re-extraction of Mg from Mg-Nd alloy and the eventual recovery of pure Mg. As a result, metal Nd with 98 % purity was directly recovered from magnet scraps under certain conditions. It was also shown that the extraction agent Mg could be reused. The results of this investigation show the possibility of establishing a new process for the direct extraction of Nd in pure metal form without oxidization.

Jan 1, 2003

By Rajashekhar Marthi

Lithium is a key component for future electric vehicle batteries and energy storage. The future availability of lithium to meet the growing demands remains in question. Around 60% of lithium resources exist in the form of continental brines. Traditional methods to recover lithium from brines use solar concentration with precipitation and have found limitations in lithium extraction due to interference of Mg in high Mg/Li brines. Thus, there is a need for highly selective adsorbents. Recently, spinel structured delithiated lithium manganese oxides have demonstrated promising results. However, due to the small particle sizes, it is economically difficult to recover the adsorbents and thereby limits industrial applications. In our work, LiMn2O4 ion sieve was synthesized and immobilized on diatomaceous earth. Fundamental adsorption studies were carried out in lithium buffer solutions to understand the nature of adsorption and kinetics. The adsorbents were also tested for recycle stability, as well as recovery of lithium from Great Salt Lake water samples.