Search Documents

By L. Yan, C. Zhou, M. Reyes

"The MINER Act requires the installation of post-accident, two-way communications and electronic tracking systems for all coal mines. One communication system which can satisfy this requirement is an electrode-based, through-the-earth (TTE) communication system, which sends signal directly through the overburden of a mine. The performance of these types of systems relies on several controlling factors such as earth conductivity, overburden depth, operating frequency, TX/RX antenna length, TX/RX offset, TX/RX orientation angle and TX current. In an effort to estimate attenuation through the earth, NIOSH researchers developed an analytic solution for the electrical field distribution of an electrode-based TTE communication system for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source. The analytic model was then validated using test data measured at an operating coal mine. The validated model can be used to optimize the operating frequency, estimate the required transmitting current, choose appropriate TX/RX orientation, and predict the performance of an electrode-based TTE system at a coal mine. INTRODUCTION One of the requirements of the Mine Improvement and New Emergency Response Act (MINER Act) of 2006 is the installation of post-accident, two-way communications and electronic tracking systems for all underground coal mines. As one of the through-the-earth (TTE) wireless communication methods available for the mining industry, the electrode-based, or linear, TTE systems establish communication by inducing a current within the earth medium by use of a pair of current probes. The resultant current is detected as a voltage by a similar set of distant probes. These probes could be an insulated piece of wire tied to two electrodes grounded at distant ends, or the grounded ends could be rails, roof bolts, or grounded electric rods. The analytical solution developed in a homogenous half-space, for this form for various transmitter/receiver (TX/RX) configurations, will be presented in this paper. The communication signals can be sent either from underground to surface (uplink) or from surface to underground (downlink). In order to achieve a successful communication link, it is necessary to understand the electric fields within the earth so that the appropriate size of transmitting antenna, TX/RX relative orientation, and operating frequency can be chosen. Hill and Wait gave the explicit forms of partial magnetic fields and partial electric fields of electrode-based TTE downlink communication with finite cable length [1]. In prior research, the E-fields of electric line transmitter were obtained for a static TX current [2] [3]. In this paper, the general and explicit forms for electrode-based TTE electric fields are developed and presented. The solutions for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source obtained from these forms are presented. Also, factors that affect the E-field strength at RX are discussed."

Jan 1, 2017

By Alessandro Boscaro, Daniele Martinelli, Cristina Gabriela Oñate Salazar, Daniele Peila, Carmine Todaro

"The wear phenomenon in TBM machines is not a simple issue, as many parameters are playing an important role on the consumption of the tools during a tunnel excavation. The action of the wear due to the contact with the soil can occur on the excavation tools, on the cutterhead, in the excavating chamber and on the screw conveyor. The test developed at the Laboratory “Tunnelling and Underground Space Center” of the Politecnico di Torino is aimed to reproduce the interaction between the tools and the excavated material, simulating the excavation conditions in terms of soil conditioning and water content. The test, which is not standardized, is studied to evaluate the wear in a global point of view. The present work starts by testing the influence of the use of chemical agents during the conditioning phase on the drop of the wear phenomenon, in terms of metal weight loss. 1. INTRODUCTION The wear phenomenon of the excavation tools used in TBM tunneling machines is playing recently a major role in the design stage of full-section tunnels in both soils and rocks. Concerning EPB excavation technology, the main issue regarding productivity is the wear of its components (Peila et al.,2012), which increases the so called dead time in the whole process. The friction generated between the components and the ground causes the consumption of the tools and other metallic components in contact with the ground, described as primary and secondary wear by Nielsen et al. (2006a). This leads to downtime, with risky and complicated maintenance operations (Peila and Schulkins, 2009), as occurred in recent tunneling works in Liguria (Italy). The study of this argument in granular soils is very delicate, as it encloses not only the properties of the excavation tools, but also the characteristics of the ground to be excavated (hardness, mineralogy composition, shape and dimension of the particles and moisture content). The penetration mechanism is based on the scraping of the ground, by mean of cutting tools, with its consequent consumption. Concerning the rocks, the excavation principle is characterized by crushing the rock mass matrix by applying high compressive stresses through cutting disks. In such a way, to avoid frequent downtimes and their consequent economic losses, it is very important to study this subject and therefore understand and forecast the durability of the components, in order to try to maximize the productivity of the machine by reducing the frequency of maintenance stoppings."

Jan 1, 2016

By Stanley O. Reichert

At nuclear facilities, three types of radioactive waste must be managed: (1) high-level liquid waste containing fission products from the chemical separation of irradiated uranium, (2) low-level condensates from the concentration of the high-level waste, and (3) dry solids such as obsolete process equipment, spent ion exchange resins, and irradiated metal scrap. The geological and environmental characteristics of a site are important considerations in planning the waste management program. At the Savannah River Plant, low-level liquids and dry solids are safely and economically placed in the soil where the geologic and hydrologic conditions are favorable. Within the general area where the waste originates, studies are made to locate seepage basins and burial grounds in the most favorable sites: (1) soils should have a high ion exchange capacity and moderate to low permeability, (2) the water table should be deep, and (3) burial sites should be relatively distant from the nearest flowing stream.

Jan 1, 1968

By R. D. Coursen

Tin has been one of the very few commodities which has been covered by an international commodity agreement. It is the only metal so covered. The reason behind tin&apos;s prediliction for an agreement has been the inconsistency of the price pattern for tin during the entire 20th century. It is not surprising in view - of the wide and wild fluctuations in its price that tin has been called the Cinderella metal. An examination, for example, of prices in 1977 alone attests to the erratic behavior of the tin markets. The high was recorded on October 27 at M$1,895 per picul and the low on January 3 at M$l,314 3/8, on the Penang market, a spread in Malaysian dollars of $581 for a picul weighing 133 1/3 pounds. The first steps in international cooperation on tin were taken after the price bonanza of the First World War. Despite a lack of increased consumption, and in spite of the fact there was no shortage of mining production during the war, prices boomed. Shipping shortages and thinning stocks brought about a situation where in the U.S., industrial stocks were only 1/6 of what they had been in 1914. The boom busted early. In 1921 the tinplate industry of the world had cut its output in half and total world consumption of tin fell by 1/3. Tin producers became so concerned that they created what was called the Bandoeng Pool. It accumulated stocks held by countries now known as Indonesia and Malaysia, amounting to 28 percent of the combined production of the two countries and about 15 percent of the total world for 1921. The pool holdings were shortly exhausted and thereafter in the years 1924 to 1928, general boom conditions existed for tin.

Jan 1, 1978

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer studies as well as for studies conducted in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources has been previously demonstrated in underground mines, but this new work details the testing of multiple, distinct tracer compounds compatible with passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed: (1) PMCH, (2) perfluoroethylcyclohexane (PECH) and perfluoromethylcyclopentane (PMCP). The release rates of these tracers were examined over a 180-day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in characterizing ventilation circuits, flow through gob and leakage. IntroductionThe use of tracer gases for ventilation applications is an established practice, with various past research projects conducted using sulfur hexafluoride (SF6). Tracer gas techniques have been applied to assess flow rates, dilutions rates and auxiliary ventilation system efficiencies with quick, reliable and accurate results (Suglo and Frimpong, 2002). Perfluorocarbon tracer (PFT) compounds are a new introduction to ventilation and air modeling applications in terms of ventilation flow characterization (Watson et al., 2007).PFTs are liquids that are characterized by low background presence in air, low reactivity, high detectability and low toxicity. A design was proposed, called a permeation plug release vessel (PPRV), to convert PFTs from a liquid to a gas and then release the gaseous tracer in a controlled manner. The initial concept was originally introduced by Brookhaven National Laboratory and refined later to become the PPRV. The PPRV functions by allowing the volatile PFT liquid to become a vapor in a controlled manner. The vapor diffuses through a permeable silicone stopper at a predictable rate proportional to temperature (Zhang and Cloud, 2006)."

Jan 2, 2018

By Jorge Ferrero, Andreas Raedle, Uhland Konrad, Michael Dutton, Keivan Pak Iman, Walter Trisi

Strabag, in partnership with Arup, is constructing the Advance Tunnel for the Scarborough Subway Extension (ATSSE); a project by Metrolinx and Infrastructure Ontario (Sponsors). The 10.7 m internal diameter single bore tunnel represents a significant departure from the traditional arrangement of twin subway tunnels in North America. ATSSE is the first-time steel fibers are used to solely reinforce a tunnel of this size in Eastern Canada. This paper discusses the challenges with design and acceptance of SFRC segments and the state-of-the-art numerical models employed to check the joint performance. The advance procurement approach for TBM and PCTL’s procurement to accelerate the project schedule is also presented.

Jun 13, 2023

By G. J. Allen

Kennecott Copper Corporation&apos;s Nevada Mines Division initiated a program to stabilize the inactive portions of the tailings disposal area and perimeter dikes in 1946. To date, approximately 1,000 acres have been stabilized with vegetation and ground cover.

Jan 1, 1978

By Monica Campos, Jose Mujica, Maria Campos

The extraction and processing of metals and other minerals have played an important role in economic, political, and social development worldwide, from the early stages of prehistory to the present day (Gosner, 2020). In other words, mining has been a fundamental part of human civilization, providing the raw materials necessary for technological, infrastructure, and industrial advances. As society progresses, the importance of mining continues to grow, supporting the development of everything from the smallest electronic devices to the tallest skyscrapers (The Importance Of Mining In Modern Society, 2024). The mining industry is closely linked to a country’s economy and activities related to natural resources. The economy of a nation is connected to its extractive industries (Moreira & McMahon, 2014), which have seen dramatic growth in recent years (Pietrobelli et al., 2018). In a context of increasing demand for natural resources, driven by the development of emerging technologies, the expansion of infrastructure, and the foundation of engineering achievements for the coming decades (Importance Of Mining - Minerals Education Coalition, 2024), mining should focus efforts on global development, requiring a comprehensive approach to sustainability that addresses the planet’s needs and protects the well-being, primarily, of the communities and environments where mining operations take place (Figari, 2024). In these areas, diversity and inclusion should be promoted, thus fostering equitable and sustainable development. Speaking of sustainable development, diversity, and inclusion brings us to an interesting topic: the Sustainable Development Goals (SDGs), also known as the Global Goals, which could serve as a key framework for fostering a strong social management culture in mining. The SDGs were adopted by the United Nations in 2015 as a universal call to end poverty, protect the planet, and ensure that all people enjoy peace and prosperity by 2030 (Sustainable Development Goals, n.d.). Companies have compelling reasons to align their actions with the SDGs, as their long-term success depends on healthy communities. This is a major challenge and requires collaborative efforts (Singh & Rahman, 2021). As Fraser (2021) mentions, achieving more sustainable outcomes may involve mining companies and communities working together collaboratively. This research proposes an innovative approach: Inclusive Mining for Sustainable Development, which aims not only to maximize economic profitability but also to promote social and environmental well-being by integrating the United Nations’ Sustainable Development Goals (SDGs), primarily focused on diversity and inclusion. This can be achieved through the implementation of a key value-added initiative for mining companies: the Creation and operation of a corporate volunteering program aimed at developing and executing inclusive practices to promote gender equality, the inclusion of local communities and indigenous peoples, and accessibility for people with disabilities. This proposal will educate employees and stakeholders about sustainability and promote concrete actions through corporate volunteering to strengthen the mining company’s commitment to community development, improve social relations, and advance toward achieving the United Nations’ Sustainable Development Goals, establishing the company as a global change agent.

Feb 1, 2025

By J. Kretschmann, A. Müterthies, T. Rudolph, C. Yang, P. Goerke-Mallet

Catastrophic failures of dams and tailing storage facilities (TSF) have triggered the development of integrated ground monitoring concepts for hazard assessment, risk management and public safety. These concepts are based on knowledge and expertise of persons technically responsible for TSF. The aim is to combine this implicit and explicit knowledge with the data of in-situ- and remote sensors. Risk management for TSF must include a comprehensive monitoring program that integrates data from ground based-, air-borneand satellite-based sensors. Researchers at Technical University Georg Agricola (THGA) in Bochum, and EFTAS, Muenster, Germany, are fusing a variety of sensor data to enhance the capability and performance of TSF monitoring to ensure public safety downstream of TSFs. This paper describes the variety of sensors implemented in numerous research projects. It gives an outlook in terms of planned satellite missions with innovative equipment like hyperspectral sensors. The implementation of the data of these sensors in the analysis will increase the understanding of spatio-temporal impacts of mining activities. Future opportunities are explained by a datacube approach.

Mar 2, 2022

By S. Thibeault, P. Filiatreault, B. Straight, D. Castendyk, L. Cameron

"Unmanned aerial vehicles (UAV), or drones, capable of collecting and retrieving water samples from pit lakes, tailings ponds and other mine water basins will revolutionize environmental programs by lowering sampling costs and reducing safety related risks. Costs typically include a boat and associated equipment, boat transportation, road maintenance, water safety devices, water safety training, and additional staff. Typically, the total cost can exceed $20,000 USD per sampling event (excluding lab analyses). Hazards include potential for drowning, unstable pit walls, and unconsolidated sediment surrounding tailings ponds. Hatch has developed a novel device for aerial drones which currently enables the collection of water samples from depths up to 390 ft (119 m). This system only requires a pilot, a sample technician, and a safe operations point overlooking the water body. Hatch anticipates this will reduce monitoring cost by at least 50% while improving safety, reducing staffing requirements and accelerating data acquisition. This manuscript demonstrates profiling and sample collection from a 95 ft (29 m) deep reservoir and a 377 ft (115 m) deep pit lake, and highlights the potential of this emerging technology. INTRODUCTION Working on or near water at active, closed, or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the United States Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at US metal, non-metal, and coal mines (MSHA, 2000). Open pit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including drowning, hypothermia, falls to the ground from the top of high walls, and rock avalanches resulting from steep, unstable pit walls. Some pit lakes are simply not easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on at least an annual basis is required to monitor the evolution of water quality over time, to verify the accuracy of numerical predictions, and to manage lake water chemistry in order to produce “treatable” influent to water treatment plants, and ultimately, produce acceptable site discharge water quality. As a product of these risks and the need for water sample, mining companies spend considerable expense on pit lake safety as part of monitoring. This includes training personnel for “on water” duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices, and mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface, employing spotters with direct communication to emergency medical services to watch sampling activities (because cell phones and radio signals can be blocked by pit walls), and utilizing redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires pit lake water samplers to hold Marine Emergency Duties (MED) training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel, and uses three boats for water sampling: two on the water at all times, and one on the shoreline, ready to deploy. The costs of these safety mechanisms greatly adds to the overall expense associated with pit lake sampling. Consequently, environmental programs may need to reduce the frequency of pit lake sampling in order to keep monitoring programs within an acceptable budget"

Jan 1, 2017

By A. J. Teske

Sustainable Development is a very broad initiative in the mining industry, with major components running over the entire life of the mine. It likely commences with pre-exploration permitting and continues to post-mining final closure and possible land reuse. Most major mining corporations embrace the sustainability initiative, either out of a sense of social responsibility or out of necessity in order to continue doing business. But many may view the overall initiative as an added ?cost of doing business.? In many elements of sustainability, there clearly can be added cost ? some as simple as complying with self-imposed sustainability reporting. Fortunately, one major element of sustainable development can clearly be shown to reduce costs ? energy resource management. This paper will describe how the mining industry sustainable development effort differs from other industries, but can benefit from their experience in energy resource management. The mining industry can utilize proven methods from other industries to further their energy management efforts. In addition, many of the resources developed and employed to promote better energy resource management in non-mining industrial settings will be listed.

Jan 1, 2010

By Shawna Von Stockhausen, Hong Yang, Tung T. Vu, Derek Penrice, Kevin Huynh

"The Regional Connector Transit Corridor is a 1.9 mile long light rail transit project in downtown Los Angeles, California. The project includes approximately 4,930 feet of twin bored tunnels together with a mined crossover cavern, 3 deep stations, and other cut-and-cover structures. The bored tunnels will be excavated using an earth pressure balance tunnel boring machine through Fernando Formation (extremely weak to weak rock) and alluvium. The tunneling will be performed in close proximity to a large number of existing structures, including the existing Metro Red Line tunnels with as little as 6 feet of separation. Thus, the evaluations of the tunneling effect on these structures and the instrumentation and monitoring program is an essential part of the project design. This paper provides a very brief overview of the considerations and evaluations of the tunneling effects on the existing structures and results of evaluation obtained during the final design stage of the project. INTRODUCTION The proposed Regional Connector Transit Corridor (RCTC) project provides a 1.9 mile-long connection between the Metro Gold Line from Pasadena and East Los Angeles; and the Metro Blue Line to Long Beach and the Expo Line to Culver City. The alignment is shown in Figure 1. The Regional Connector will provide new tracks through downtown Los Angeles. The project will extend underground from the Metro Blue, Expo, Red, and Purple Lines’ 7th Street/Metro Center Station following Flower Street, curving northeast to the north of 3rd Street under the 2nd Street Tunnel. The alignment will then continue eastward under 2nd Street, turning northeast to cross under the intersection of 1st and Alameda Streets, then splitting into two branches above the ground surface, one branch extending north along Alameda Street and the other extending east along 1st Street. The project elements include 3 deep stations, a SEM cavern, segments of TBM bored tunnels, and cut-and-cover guideway structures. The bored tunnels have an excavated diameter of 20.3 feet. The subsurface conditions along the tunnel alignment generally consist of artificial fill overlaying finer-grained alluvium (dominantly medium dense to dense sandy soils), underlain by coarser-grained alluvium (a wide variety of medium dense to dense sandy and gravely soils). Below the coarser-grained alluvium is Fernando Formation, which is characterized as extremely weak to very weak sedimentary bedrock. A long stretch of the alignment will be excavated in this formation. The soil layers above the Fernando Formation are of variable thickness and spatial distribution. The geologic profile is shown in Figure 2."

Jan 1, 2016

By FJ. Johnson

Polymer utilization has increased steadily over the past several decades; however, their usefulness is sometimes limited by natural forces. For example, polymers tend to degrade when subjected to elevated temperatures. This degradation can release toxic fumes, create excess smoke, and aid in the spread of fire. For these reasons, many polymers are filled with various compounds which impart flame retardancy (FR) properties. These fillers do not make polymers non-combustible; rather, they increase resistance to ignition and reduce bum rate. Also, they suppress smoke generation, which is important as up to 80% of fire-related deaths are due to smoke inhalation [1]. Therefore, methods to impart flame retardancy in polymers are industrially important. The early flame retardants used in polymers were halogen-based, working on the principle of inhibiting free radical formation in the vapour phase thus impeding combustion propagation [2]. Usually these were combined with antimony compounds such as Sb203 to decrease loading, yet provide the same FR qualities. However, questions have arisen recently concerning toxicity of halogenated flame retardants. Possible release of toxic compounds (such as dioxins) upon combustion has been reported [3]. Fear of future regulations concerning halogen addition has led to the search for different FR fillers. Two of the more common replacements for halogen-based systems are alumina trihydrate (Al(OH)3 or ATH), and magnesium hydroxide (Mg(OH)2)&apos; These systems impart flame retardancy through heat absorption and by release of water of hydration upon their decomposition. ATH has a low decomposition temperature (230°C), limiting its use to unsaturated polymers, epoxies, urethanes, and some wire and cable formulations. However, some advantages of ATH over halogenated FR are that it is relatively cheap, doesn&apos;t generate toxic gases, is non-volatile, and is impervious to moisture [2].

Jan 1, 1997

By E. Yan, M. Mankosa, G. Luttrell

"During the past decade, column flotation cells have become widely accepted for upgrading ultrafine sulfide ores. However, the use of columns has been widely relegated to cleaner circuits due to their comparatively high selectivity derived from the use of wash water dispersed over a deep froth. High tonnage rates and low feed grades make using column technology in roughing and scavenger stages challenging due to the resulting size of the needed equipment. To specifically address this challenge, a new high-intensity flotation system known as the StackCell™ was developed. This technology makes use of a novel pre-aeration method coupled with froth washing to simultaneously provide improved flotation kinetics and selectivity. The novel aeration system provides efficient bubble-particle contacting thereby shortening the residence time required for particle collection. This article reviews the technical design features of this new flotation technology and presents recent data from in-plant pilot testing in a copper-sulfide application. INTRODUCTION Column flotation cells have become very popular in the minerals processing industry for cleaner circuits due to their ability to produce a high-grade froth concentrate via the use of froth washing (Luttrell et al., 1999; Kohmuench et al., 2004). The use of wash water minimizes the nonselective recovery of ultrafine impurities that are normally entrained into the froth product from conventional flotation machines. On the other hand, the unique design of a column cell typically requires a large tank volume. Column cells must be tall to ensure that the pulp residence time is long enough to offset their inherently slow flotation kinetics and to minimize internal mixing that is detrimental to overall cell performance. The tall design minimizes the total floor space required for the column installation, but substantially increases the foundation load. The large size of the column tank can also create issues during fabrication, transportation and installation. To address these concerns, the engineering team at Eriez Manufacturing developed a next-generation flotation technology called the StackCell?. This high-intensity flotation machine was designed to provide column-like separation performance within a very compact volumetric footprint. This article describes the key working features of this new technology and provides data from recent pilot-scale tests conducted in gold and copper-sulfide applications"

Jan 1, 2016

By J. Y. Hwang

Processing of fine mineral particles in a slurry is a difficult problem. Methods to make fine particles magnetic have been developed recently and may offer a solution to this problem. Particles of nonmagnetic materials can be selectively rendered magnetic through surface interactions with magnetic reagents. When adsorption occurs, the magnetic susceptibility of the material is increased. Magnetic enhancement at several orders of magnitude can be achieved. Selectivity of the adsorption can be controlled by the functional groups of magnetic reagents and various surface interaction mechanisms. This approach allows a new degree of freedom for the processing of fine mineral particles, even with conventional magnetic means. Separation of valuable minerals and filtration of slimes from tailing ponds and recirculated water are examples of the applications. Basic principles of this technology are discussed in this study.

Jan 1, 1992

By J. P. Ulery

As a result of several recent methane/dust ignitions in surface auger and highwall mines, the U.S. Bureau of Mines investigated the occurrence of methane gas at these operations. Three mine sites were visited in western Kentucky and one in western Pennsylvania to collect run-of-mine coal samples for gas content determination using the modified-direct-method (MOM). Results indicate the samples emitted small quantities of methane, carbon dioxide, and nitrogen. Either methane or nitrogen was the predominant gas released. The same gases were released after crushing the samples for residual gas content; however, nitrogen was the primary component of this fraction. Total ~as contents ranged from less than 0.01 cm /g to 0.54 cm3/g. The hydrocarbon gases probably originated during coalification. Other gases may have originated partially as a byproduct of coalification and partially as a result of other, near-surface processes. The data suggest that although methane quantities are small, desorption could occur at near surface conditions prior to mining. The desorbed methane could accumulate as a free gas in fractures in the coal bed or roof rock. When these fractures are penetrated by the auger, methane could rapidly enter the whole atmosphere possibly creating explosive conditions.

Jan 1, 1994

By Ross W. Whipple

Applying geophysical techniques in potential geothermal areas has received: little attention in the United States, though it is widely used and accepted in New Zealand and Italy. In those countries it has been demonstrated that geophysical surveys can be useful in locating new geothermal areas and in directing test drilling programs. Geophysical studies in a thermal region can provide structural information and, if conditions are right directly; locate subsurface hot waters. They can give indications of sub-alluvial rock types and of the thickness of alluvial cover. In certain cases they can be used to estimate the power potential of a hydrothermal system.

Jan 1, 1963

By Jr. Bacon

Kaolin clay is one of the yeoman minerals. It sees duty in almost every aspect of our lives: -in and on most paper products (from modern newsprint to National Geographic and packaging board) sometimes as much as 25% (by weight) of the product -40% of the tile (ceramic, rubber, and linoleum) you walk on. -15 % of the tires you ride on, -30% of the fiberglass filaments in circuit boards, bathtubs, boats, doors, and more, -25% of many housepaints, adhesives, grouts, caulks, and putty -30% of sparkplugs, power insulators, dinnerware. and toilets, -50% of most catalysts (both cracking and emission control) -20% of cosmetic powders. -20% of wire insulation, and animal feed to rocket insulation!

Jan 1, 1993

By C. Braux

The aim of this study was to develop an integrated approach to enable identification of areas favourable for the presence of massive sulphide deposits in a given region (Las Herrerias, Spain). It is based on geochemical soil exploration, geophysical surveying (ground gravimetry), detailed geological mapping and a knowledge of the deposits of the South Iberian Massive Sulphide Belt. The multi-dataset approach consists, in the first instance, in standardizing and combining all the geochemical data with reference to their geological setting. Next, the "heavy" anomalies are extracted from the gravimetric survey, regardless of the surrounding context (heavy or light). The results from these two stages are then crossed, so that areas where heavy anomalies are associated with geochemical anomalies can be identified and classified. Crossing the geochemical and geophysical data enables a much tighter selection of anomalies than does the manual superposition of data provided by each method (geology, geophysics, geochemistry).

Jan 1, 1994

By S. K. Mohanty, T. M. Dittrich, M. J. Allen, M. Dardona, A. C. Strzelecki, J. Hovey, Boukhalfa. H.

Rare earth elements (REEs) have many critical uses in advanced technology and the lack of a reliable domestic supply has been identified by the US DOE as a vulnerability to US economic security. Our research focuses on developing an economical process for extracting REEs from coal fly ash and power plant wastewater sludge by coupling a hydrothermal extraction process with the engineering of a ligand-associated media for concentrating REEs from the extraction liquid. Ash samples have been collected from two Detroit-area Power plants that burn 100% low sulfur coal (Trenton Channel) or fuel blends of 75% low sulfur coal and 25% high sulfur coal or 70% low sulfur coal, 15% high sulfur coal, and 15% petcoek (Monroe Power Plant). Ash samples are then subjected to hydrothermal conditions from 100-350 °C for 1-24 h at Los Alamos National Laboratory and leachate concentrations are measured by inductively coupled plasma-mass spectroscopy (ICP-MS) and compared to hydrofluoric acid digestion results. Experiments designed to aid in ligand selection and loading optimization show that di-(2-ethylhexyl)methanediphosphonic acid (H2DEH or DIPEX™) can be successfully loaded to a commercially available swellable organically modified silica (SOMS) media. Preliminary results show that DIPEX-associated SOMS surface loading can exceed 4x on a mass/mass basis and in simplified sorption experiments with Nd solutions (~pH 2), the DIPEX-SOMS media can sorb >90 mg Nd per g of media. Recovery of the sorbed Nd with low pH solutions has had low efficiency with the high (4 g DIPEX/ g dry media); however, near complete recovery was achieved with lower surface loadings (0.05 g DIPEX/ g dry media). Column experiments are being conducted to evaluate the optimal ligand/media ratio for repeated use. Completive sorption with Fe and other major cations are also being evaluated.

Jan 1, 2019