Search Documents

By D. An, J. Withers

A nano-scale investigation has been carried out by applying an AFM (atomic force microscope) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it contacts the solutions of the collectors, suggesting that all these collectors can effectively adsorb on bastnaesite. Increasing temperature can help increase the adsorption of oleic acid on bastnaesite. FTIR (Fourier transform infrared) results also show that all these collectors adsorb strongly on bastnaesite with a strong absorbance spectra being detected, which confirms with the results obtained with AFM imaging analysis. In general, hydroxamic acid collector (HA and SHA) adsorbs on bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite. INTRODUCTION Rare earth metals, which are very important to modern industry, are generally extracted from numerous rare earth minerals. In practice, however, the actual extraction of rare earth is mainly from bastnaesite, monazite and xenotime. The Mountain Pass mine is one of the largest rare earth mine in the world, at which the main rare earth mineral is bastnaesite. In the past years, froth flotation has been applied to the beneficiation of Mountain Pass ore. In practice, the rare earth ore is usually crushed, milled and further separated from calcite, barite and other gangue minerals by froth flotation, in which the rare earth oxide-bearing minerals stick to aerated bubbles in the pulp and float to the surface, leaving the gangue at the bottom of the flotation cell and disposed of as tailings.(Bulatovic, 2010) In spite of the fact that froth flotation has been applied to treat the bastnaesite ore at the Mountain Pass mine, the rare earth oxide (REO) recovery is still low,(Anderson, 2015) especially compared to the one obtained with sulfide flotation. For example, the typical recovery obtained at the Mountain Pass mine was only about 70%. This may be due to the low selectivity of the collector (oleic acid). In addition, to enhance the flotation selectivity, the pulp in the mine circuit has to be heated up to 70 to 90°C and it involves a lot of energy consumption. Last but not the least, a lot of depressants have to be added to improve the selectivity of flotation process. Therefore, it is critical to re-examine the existing flotation process at the Mountain Pass mine and seek any chance of improvement. (Anderson, 2015)

Jan 1, 2019

By S. Peng, N. Vayenas, A. Farah

"While genetic algorithms have been widely adopted in ore grade estimation and optimization, mine design, and production scheduling in the mining engineering field, reliability and maintainability analysis of mining equipment using genetic algorithms has been a relatively new research area in recent years. This paper presents an application of genetic algorithms using case studies with seven underground scoop trams whose maintenance records have been collected over a period of 12 months from an underground mine in the Sudbury mining area. Based on the assumption that various factors that contribute to machine failures resemble the biological evolution process, the authors have developed an in-house PC software application called GenRel which adopts genetic algorithms in its programming. In this study, the authors feed the historical maintenance data into GenRel in order to predict future maintenance characteristics of mining equipment in a time period of three months. Then the predicted maintenance characteristics are compared to the actual maintenance records in the same time period. A statistical study is then used to examine the similarity between the predicted data and the recorded data.INTRODUCTION Today maintenance costs of sophisticated engineering systems are so high that maintainability draws great attention from scientific researchers to operations managers. For instance, a study by [1] shows that American manufacturers spend more than 300 billion U.S. dollars on plant maintenance and operations. Therefore it is understandable that the main objectives of applying maintainability principles to engineering systems are to reduce projected maintenance costs, to use maintainability data to estimate system or equipment availability/unavailability and to determine labor-hours and other related resources needed to perform the projected maintenance. A system with better maintainability would inherently provide the benefit of lower maintenance costs, less time to recover with lower breakdown frequency (design for simplicity), less complexity of maintenance tasks and relatively reduced man-hours [2]. Most maintainability functions use the Time To Repair (TTR) as the independent variable. It is common to use probabilistic or statistical concepts to define a maintainability function, for example, the probability density function. Let t denote the time. Assuming a repair starts at t=0 and completes at time T, the maintainability can be mathematically defined [3] as in Equation (1)."

Jan 1, 2015

By M. M. Carpenter

Specialty chemicals are widely used in the industrial minerals process industry for many different purposes including beneficiation, filtration, flocculation, dispersion and biological control. Optimal use of such chemicals can confer benefits both in terms of cost efficiency and end product attributes. In this paper we will review recent progress in the fundamental understanding of mineral additive interactions and present data which show how optimization can lead to improved products.

Jan 1, 1999

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By Lawrence S. O’Rourke

Pricing for tantalum raw materials experienced explosive increases in the period 1978-1979, and-similar declines over 1980-1982. The causes for this are examined. Negative effects on the industry are highlighted. Analysis is provided of subsequent structural changes within the industry which minimize probability of future pricing excursions. Data on markets, sources of material, and outlines of concentration and extractive processes are reviewed. The conclusion is reached that expanded sources, future flat demand, and a broader international base of industry participants are principal forces in this restructure. Flat demand is reviewed as a function of increasing application of tantalum, but in more cost effective forms. This is driven by technical advance, notably in electronics applications.

Jan 1, 1986

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016

By H. EI-shall

Bench top centrifuge is used to study the consolidation behavior of phosphatic clays. A mathematical model (based on first order kinetics) is developed to describe the relationship between the void ratio (at any time) and the effective stress. Permeability of the sediment as a function of the void ratio is also described. The obtained data are compared with that obtained by other consolidation testing methods. Centrifuge results indicate that consolidation data may be developed in a short period of time (hours) as compared to days or weeks when other techniques are used.

Jan 1, 1995

It is well established that the results of emulsion flotation in which water-insoluble oily collectors are utilized depend critically on the emulsification of the collector and on its conditioning with the pulp prior to flotation. The flotation tests carried out with magnesite and fluorite using sodium oleate as collector confirmed acidic and alkaline ranges of good flotation. While the flotation results in the acidic solutions depend strongly on the conditioning time and can be very much improved when longer conditioning times are utilized, the tests in the alkaline environment do not exhibit any significant dependence on conditioning. The results obtained with sodium salts of myristic and lauric acids confirm these findings. The observed effects provide additional evidence for the role of the colloidal species which appear in the acidic solutions of weak electrolyte type surfactants, such as fatty acids. The flotation properties of sodium oleate in the pH region in which it appears in the form of oleic acid droplets are mainly determined by the properties of such droplets. The flotation in this pH region closely resembles an emulsion flotation.

Jan 1, 1993

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Chester A. Rowland

La conminución de Ios minerales es, generalmente, una etapa de preparación de la alimentación para las subsiguientes etapas del proceso. La molienda, fase de conminución de productos finos, requiere una gran inversión de capital y frecuentemente es el área de máxima utilización de potencia y de materiales resistentes al desgaste. La molienda se produce normalmente en tambores rotativos que utilizan un medio de molienda que se pierde en la misma, al elevarse con la rotación del tambor, se rompe el mineral por combinación de los efectos de impacto, atrición y abrasión, hasta producir el producto especificado. El medio de molienda pueda ser: - El propio mineral (molienda autógena - primaria y secundaria). - Medio no metálico, natural o fabricado (pebbles) - Medio metálico (barras o bolas de acero) Este capítulo tratará de molinos de barras y bolas que utilicen medio metálico de molienda.

Jan 1, 1982

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

By E. Manev

Thin aqueous equilibrium film studies and surface tension measurements on a mixed surfactant system consisting of polyethylene oxide (a model frother) and potassium ethyl xanthate (a model collector) enable the interaction between the two surfactants at the air/solution interface to be elucidated. For the film containing the non-ionic frother, the interface was charged and addition of low concentrations of xanthate acted as a common electrolyte and reduced the thickness of the film inducing rupture. However, at high xanthate collector concentrations, the negative charge xanthate was found to interact with the non-ionic and caused a build-up of negative charge at the air/solution. Higher frother concentrations were necessary to produce non-rupturing thin films upon increasing the xanthate concentration.

Jan 1, 1992

By George Vranesh

Synfuels development in the upper Colorado River basin and the population growth attendant with such development demand sizeable quantities of water. Unfortunately, the water supply in the basin is limited and such limitation may impose a significant constraint on the development of the West's abundant energy resources. Although the water for the synfuels development will be governed by the law of prior appropriation adopted in the upper basin states, the authors point out that an apparently senior water right .my not deliver a firm supply of water. The federal and Indian Reserved Water Rights Doctrine, the Colorado River Compacts the Doctrine of Equitable Apportionment, and the federal and state environmental laws can all severely diminish the value of any given water right and the synfuels industry should take care to evaluate these factors in acquiring its water.

Jan 1, 1981

By W. L. Price

Recent publication of United States Bureau of Mines figures showed that the sand and gravel (3) industry is the largest single mining industry in the United States in term of yearly tonnage produced. The yearly production of over 500,000,000 tons per year now exceed bituminous coal production. This disclosure caught unawares many observers who have not been following closely the rapid-growth of this phase of mining. Along with this steady growth in production, the sand and gravel industry has gone through an accelerated and varied program of beneficiation in a period of the last ten years.

Jan 1, 1958

By M. Westerstrand

It is known that the water chemistry of the process water during ore refinement can affect product quality, such as iron pellet strength. The main objective of this study was to quantify the amounts of major elements, such as Ca, Mg, Na, S and Cl carried by process water and by magnetite grain surfaces to the end product, iron ore pellets made from magnetite ore from the Kiirunavaara Mine in northern Sweden. In addition, the amount of colloids (0.22µm ? 1kD) in the process water was examined by ultrafiltration. The amounts of various elements sorbed to the magnetite surfaces were estimated by leaching with Milli-Q water, MgCl2, NH4-acetate and Na-acetate. Total dissolved solids were between 1,446 and 1,775 mg/l, dominated by Ca, S, Na and Cl (89%). The colloidal fraction was less than 3% for major ions. For Ca and Mg, sorption to magnetite surfaces was a much more important transport mechanism for the pelletizing process than evaporated process water, but for Na, Cl and S process water was an important carrier.

Jan 1, 2010

By Saul Escalara

Data on sulfonate adsorption by silicate minerals are very scarce in the literatures. Perhaps the only comprehensive paper written on the topic was done by Fuerstenau and Bhappu (1); this work dealt exclusively with quartz but included many important suggestions as to the form and nature of the hydroxy-sulfonate species of some cations formed during the conditioning step and their effect on the flotation response of quartz. Another paper by the same authors (2) contains additional data on the role of hydrolysis in sulfonate flotation of beryl. As postulated by Fuerstenau and Bhappu, a solid form of cationic sulfonate functions as the collecting species to produce flotation of quartz and beryl. According to the authors, the solid compound is a hydroxy-sulfonate of a given cation, where the hydrogen of the hydroxyl part provides a means for bonding of the species to the mineral surface; thus, the presence of hydroxyl in the neutral precipitated compound is of primary importance to produce flotation. Although the preceding examples illustrate the effect of a sulfonate collector in silicate systems other than plagioclases, they are important as examples of processes of hydroxy-sulfonate complex formation. Since the plagioclase minerals con¬tain Ca(II) and Al(III) cations, which are very reactive in sulfonate media (1), the formation of hydroxy-sulfonate compounds with these cations released from the solid phase may well prove to be the cause for their flotation.

Jan 1, 1973

By Brian Y. Lattimer, Kray D. Luxbacher, Jonathan L. Hodges, Manuel J. Barros-Daza

The abstract discusses the importance of predicting fire response time (the time before conditions become untenable for firefighters) in underground coal mines. It introduces a data-driven approach using artificial neural networks (ANNs) to predict response time and fire size based on measurable parameters like CO concentration, mine geometry, air velocity, and time since fire detection. The approach was tested using simulations from fire models (FDS and FSSIM), showing promising results for real-time predictions during mine fires.

Mar 6, 2022

By D. E. Munson

The Waste Isolation Pilot Plant (WIPP) Project was established in 1975 by the Department of Energy (DOE) under Public Law 193 to develop the necessary technology for safe disposal of radioactive wastes from the defense programs of the U.S. The technology development involves extensive theoretical, numerical, and laboratory programs, as well as construction of the WIPP facility in southeastern New Mexico for in situ testing and waste storage demonstration. If after the demonstration, the facility is found to comply with regulations of the Environmental Protection Agency, then the facility will become a repository for Transuranic (TRU) waste. The underground portion of the facility is 655 m beneath the ground surface in massive natural salt deposits of the Salado formation, as shown in Figure 1.

Jan 1, 1991

By M. Wasel

The Gross Rosebel gold deposits are located in the Guiana Shield of north central Suriname. Initial discovery of surficial gold in 1880 by local artisanal miners preceded small-scale mechanized mining from 1885 to 1939. The first systematic exploration program was carried out by Placer Development from 1974 to 1977. In May 1992 Golden Star Resources optioned the property. Initial shallow reconnaissance diamond drilling of the extensive surface geochemical anomalies intersected sporadic gold mineralization with no apparent continuity between drill sections. Successive deep augering, trenching and systematic grid drilling based on information from surface mapping allowed development of a preliminary geological model. Further drilling of specific structural-lithologic targets and more complete synthesis of geological data from the trenching and deep auger sampling added to the geological model and defined the multiple controls of gold mineralization. Carefully planned infill drilling on a tighter grid spacing resulted in progressive definition of reserves within six discrete gold deposits. In a complex geological setting, the key to success at Gross Rosebel was persistent, systematic exploration, detailed mapping, careful core logging and perceptive geological interpretation. Reserves now stand at 48.6 Mt at 1.6 glt Au, or 2.4 million ounces of gold. The purpose of this paper is to describe the progression of exploration activity that led to the definition of substantial gold reserves and to summarize the geology of the deposits.

Jan 1, 1998

By Daniel G. DiCanio

Investigation of the costs of industrial accidents dates back to the 1920s. The Bureau of Mines was one of the pioneers in accident cost investigation with numerous studies published between 1928 and 1933. The bulk of these early investigations dealt only with costs which appeared as payouts on company books; that is, the direct cost of insurance premiums and the costs of medical expenses which resulted from industrial accidents. These early investigations, especially the Bureau's study of accident costs in Pennsylvania and Indiana coal mines provided the first real evidence that promotion of industrial safety pays back in dollars as well as in human life and wellbeing. In the 30s and 40s, investigations began to accumulate evidence that industrial accidents impacted more than just the direct operating expenses of a company (i.e., higher insurance premiums). The work of Heinrich pioneered these investigations, and produced strong evidence that the un¬insured costs of accidents far outweighed those costs covered by insurance. Heinrich developed and published a ratio of insured to uninsured costs of 1.4. Despite his cautionary statements about blanket application of this ratio it is used even today to estimate total costs of accidents. Simonds, in the late 40s and early 50s, extended the definitions of uninsured or indirect accident costs and developed what is now regarded as the principal method for estimating the total economic impact of industrial accidents. Simonds' method served as the basis for development of the logic of the Accident Cost Indicator Model (ACIM). However, several departures from Simonds' method were made to satisfy certain requirements imposed by the Bureau of Mines, and because information gathered during the course of our investigation justified a departure. These departures are noted in the discussion which follows.

Jan 1, 1977