Search Documents

By Oleg N. Tikhonov

A new extraction method which includes a combination of gravity and alternating electromagnetic fields with interfriction of mineral particles was proposed (Tikhonov O.N., 1979) and tested in lab conditions at Mineral Processing Department of St. Petersburg Mining Institute. At the beginning of the work the main goal was to find an efficient alternative to traditional extraction methods (like shaking table, etc.) used for concentration of fine alluvial gold particles. After the method and a series of gradually improved lab separators (Tikhonov, et al., 1983) were positively tested for gold (Tikhonov, et al.. 1986) the efficiency of the method was also proved for extraction of and other heavy minerals from alluvial and ground ores in experimental work at the St. Petersburg Mining Institute. The fine heavy minerals were separated to concentrates with high technological indices (Andreev et al., 1987), (Tikhonov, Gladkov, 1987), (Tikhonov, Gladkov 1989). In parallel a semi-industrial gravi-electro- magnetic separator was made and several technological flowsheets were designed for testing the method in industrial conditions (Tikhonov O.N., Miazin B.N., 1987), (Tikhonov O.N., Tolstunov S.A., Jebelev V.V.,1989). A series of industrial tests accompanied with complete sampling and standard technological measurements were performed at several alluvial deposits, with good technological indices. Thus the method and the flowsheets displayed high additional recovery of fine alluvial gold particles during elkrated industrial experiments in Siberia (Aldan province). At higher concentrate grade this method, even in one-stage operation, increased gold recovery more than by 25% compared with shaking table (for particles -0.10 mm gold recovery was 82% vs. 55% by shaking table, for particles - 0.25mm the recovery was 97.5% vs. 61.8%). Experiments were performed by joint team of St. Petersburg Mining Institute and the Irkutsk Institute of Rare Metals (Tikhonov O.N., Gladkov S.A., Tarasova T.B., 1991).

Jan 1, 1995

By Giovanni Toniatti

Brazil is a country with continental dimensions. It hosts many different varieties of terranes and geological environments in its 8.5 million km2 (3.28 million sq miles). This mineral endowment has been important for the country's economic and social development process since the early colonial period, leaving Brazil with a legacy of almost 400 years of mining tradition. Mining in Brazil started in the early 17th century with diamond and gold discoveries. The made the country the leading producer of both for more than a century. This phase faded by the late 18th century when the alluvial deposits were depleted. It finally yielded to competing countries where technology and capital were being applied more efficiently. This period of mining dormancy lasted from the late 19th century until the first decades of the 20th century when Brazilian mining picked up. There was growing pressure on mineral resources by the affluence of the industrial society. The fast-growing demand resulting from the two world wars had brought the Brazilian mineral wealth back to the scene. This second Brazilian mineral boom made the country a leading producer of iron and manganese ore, quartz crystals and other strategic minerals. This expansion in Brazil's mining industry provided the basis for the country's industrialization process. This was led by the Brazilian steel and petroleum industries. Unfortunately, the thrust provided by this modern industrial basis was not properly used as a lever for further industrial development. The upstream industrialization process was not supported by the proper development of the raw materials supplying basis. The resulting industrial model was heavily dependent on imports of raw materials. It did not support the economic growth and faced fierce industrial competitiveness and sophistication that emerged with the postwar economic boom.

Jan 1, 1997

By Henry R. Tiedemann, Eugene H. Skinner, George E. Wickham

The need for ground support research in underground excavation has been well identified in recent years by many studies in the subject area (1, 2, 3, 4, 5). A typical conclusion from these reports (1, 2) is that the drill-and-blast (D & B) mining or the mechanical tunnel boring machine (TBM) methods are expected to be continued in use for the needs of tunneling in the immediate future. The Organization for Economic Co-operation and Development (OECD) sponsored in June, 1970 advisory conferences on Hardrock and Soft Ground Tunneling (3,4). These two reports were based on the combined response received from approximately six hundred inquiries from 17 nations in the summer of 1969 and which concerned all aspects of present-day inadequacies of, and the needed improvements in the technology of tunneling. Some specific problem areas in ground support and tunnel linings were: 1) the ability to successfully predict rock loads that must be carried by the support system; and 2) inadequate methods for determining the load-carrying capacity of the various support systems. Therefore, the problem area is clearly defined by these two objectives: 1) To find means of predicting rock loads; and 2) To develop methodology for determining safe, efficient, and economical ground support design practices. Noting these research needs from a great number of sources, the United States Bureau of Mines, Spokane Mining Research Center (SMRC), acting as agent for the Advanced Research Projects Agency (ARPA), undertook contract research effort in these problem areas. Work by Jacobs Associates has studied a methodology for specification of temporary artificial support based on the dependent sequence of mining operations and prediction of various rock conditions in the pre-excavation stage. The major thesis is that rock behavior is the

Jan 1, 1997

By Lawrence W. Teufel

Knowledge of in situ stress and natural fracture distribution at depth improves our ability to stimulate and produce low permeability reservoirs. The focus of this study is three closely spaced, 2.5 km deep vertical wells in the Piceance Basin of Colorado. The wells were completed through the tight lenticular and blanket gas sands of the Mesaverde Group. In situ stress directions and magnitudes were determined from hydraulic fracture tests and anelastic strain recovery measurements of oriented core. The distribution, orientation, and characteristics of natural fractures in the subsurface were determined from detailed observations of over 1300 m of core, of which 400 m was oriented. Stress measurements clearly show that horizontal stresses are strongly influenced by lithology. In a sandstone/shale sequence at a depth of about 2.0 km in situ stresses in sandstone formations are anisotropic, with the average ratios of the minimum and maximum horizontal stresses to the overburden stress being 0.82 and 0.96, respectively. In sharp contrast bounding shale formations are lithostatic. This stress contrast between sandstones and bounding shale formations could act as a barrier to hydraulic fracture propagation during stimulation and impede vertical fracture growth. Natural calcite-filled fractures are present in over 7 percent of the core, with several horizons having a much higher frequency of fractures. Fractures are found primarily in sandstone. The fractures have a strong preferred orientation of N 1060E[+]110, which is aligned with the maximum horizontal stress and direction of hydraulic fracture propagation. The interaction between a well developed fracture fabric and anisotropic stresses in sandstone formations produces a permeability anisotropy, with the maximum permeability aligned with the fracture fabric and maximum horizontal stress.

Jan 1, 1986

By Frank E. McCall, Michael A. Trevits, Fred Garcia

The U.S. Bureau of Mines investigated the influence of atmospheric pressure changes on methane gas migration through mine seals at a mine site located in the Pittsburgh Coalbed. The mine gained access to a coal reserve through part of an abandoned mine and constructed nine seals to isolate the extensive old workings from the active mine area. Underground problems were experienced when atmospheric pressure fell, causing methane gas to migrate around the seals and into the active workings. During mining operations, methane gas levels exceeded legal limits and coal production was halted until the ventilation system could be improved. When mining resumed with increased air flow, methane gas concentrations occasionally exceeded the legal limits and production had to be halted until the methane level fell within the mandated limit. To assist the ventilation system, a pressure relief borehole located in the abandoned workings near the mine seals was proposed. Preliminary estimates by a gob gas simulator (computer model) suggested that a 0.76 m (2.5 ft) diameter pressure relief borehole with an exhaust fan would be necessary to remove enough methane from the abandoned area so that the ventilation system could dilute the gas in the active workings. However, by monitoring methane gas emissions and seal pressure, during periods of low atmospheric pressure, the amount of methane gas that migrated into the active mine workings was calculated. Researchers then determined that a relief borehole, 20.3 cm (8-in) with an exhaust fan could remove at least twice the maximum measured volume of migrating methane gas. Because gas concentrations in the abandoned workings could potentially reach explosive limits, it was proposed that the mine eliminate the exhaust fan. Installation of the recommended borehole and enlarging two other ventilation boreholes located in the abandoned area reduced methane gas leakage through the seals by at least 63%.

Jan 1, 1995

By Stephen G. Hardcastle, Michel G. Grenier, Kevin C. Butler

Today there are numerous electronic rotating vane and thermal (hot-wire) anemometers, as well as vortex meters available to measure air velocity. Of these, a laboratory and field evaluation has found that certain instruments are better suited to routine airflow measurements in mine roadways and ventilation ducts. This paper concludes a study sponsored by the Atomic Energy Control Board of Canada, that was introduced at the 5th U.S. Symposium. The study investigated the suitability of currently available electronic anemometers as replacements for the traditional mechanical analog devices while maintaining standard methods such as the continuous traverse. Six electronic instruments were subjected to extensive tests under controlled conditions both in a wind-tunnel and in the field at an underground mine. The evaluation concluded that ergonomics and design were major considerations in unit preference as most of the instruments had very similar performance characteristics. Specific findings were: a) In the wind-tunnel the vane anemometers, especially the "micro" vanes, were more susceptible to misalignment or yaw effects but these were not noticeable in the field; b) Both the vortex and hot-wire anemometers were suitable for continuous traverses of mine roadways; c) Traversing ventilation ducts was more practical than a Pitot-tube multi-point assessments or discharge measurements; d) Yaw is a major concern in duct measurements; e) The continuous traversing method for roadways overestimates the average air velocity; f) Hot-wire anemometers can require significant air density corrections; and g) Hot-wire anemometers are better suited than rotating vanes to mine roadways of less than 1 m/s average air velocity. Based on research detailed in this paper, the ventilation engineer should be able to match the mine's requirements with the presented instrument performance characteristics, thereby optimizing the purchase of a new anemometer and the efficiency with which air velocities are measured.

Jan 1, 1993

By Edwin A. Harre, John J. Mortvedt

Plants obtain nutrients from both air and soil. They absorb carbon dioxide mainly from the air, although some carbon dioxide may be dissolved in soil water which is absorbed by plant roots. Carbon dioxide, a gaseous form of carbon and oxygen, supplies the carbon which usually makes up 50% or more of plant structure. Growing plants use water more than any other biological substance. Plant nutrients dissolve in soil water and enter the plant via root absorption. Water is then given off into the air as the plant breathes or transpires. Water also supplies hydrogen and oxygen to plants. Plant roots absorb nutrient cations or anions by contact exchange with soil clay particles. Inorganic or mineral nutrients essential to plants are supplied through the soil. Inorganic or mineral composition of plants usually is less than 5% of their weight. In most crop-growing areas, much of this nutrition is inadequately supplied from soil reserves and must be provided by fertilizers. The role of the fertilizer industry is to provide economical, efficient, good quality fertilizers to improve or maintain soil productivity for optimum crop production. The essential plant nutrients other than carbon, hydrogen, and oxygen which often must be added to soils or plants are categorized as primary nutrients (nitrogen, phosphorus, and potassium), secondary nutrients (calcium, magnesium, and sulfur), and micronutrients (boron, chlorine, copper iron, manganese, molybdenum, and zinc). These classifications are based on quantity of nutrients utilized by plants and do not imply their function or degree of necessity. One point of major significance to the fertilizer industry is that not all fertilizer minerals contain the plant nutrients in a chemical form available to the plant. A product which may be considered a fertilizer mineral may require substantial processing or treatment before it becomes useful as a nutrient source or fertilizer.

Jan 1, 1994

By Missy Isaman

"Mixed ground tunnels come in all kinds. In rock tunnels with possible faults and high pressure water, the challenges are many. With the advent of Crossover TBMs, contractors can minimize machine wear in such conditions while maximizing efficiency. The newest generation of Crossover is exemplified by two projects in Albania and Turkey. A 5.56 m Crossover TBM destined for Turkey’s Gerede Water Transmission will be assembled using Onsite First Time Assembly (OFTA) from within an existing tunnel. The unique machine will bore through 30 fault zones requiring the TBM to be sealable to up to 20 bar so pre-consolidation grouting can be done. If boring under pressure is required, the TBM will bore sequentially using the screw conveyor fore and aft gates. Skewing further towards hard rock, a unique 6.2 m diameter Double Shield TBM with Crossover features was designed for Albania’s Moglicë Headrace Tunnel. The machine features closure doors and a sealing system to contain inrushes of water until they can be grouted off. This paper will discuss the unique aspects of the Crossover designs, including their inception as based on past projects in difficult ground, and their utilization at the two current projects. INTRODUCTION Specialized tunnel boring machines have been made for years to tackle specific types of ground conditions. Traditional types of TBMs bore within a specific set of ground conditions. If a project is located in a competent granite face, then a Main Beam machine is a good solution. In soft ground, Earth Pressure Balance (EPB) machines are the method of choice. Years of experience and engineering advancements have made both types of machines fast and economical solutions for tunneling. Unfortunately not all ground conditions are a perfect swath of one material, and the need for a more diverse machine is apparent."

Jan 1, 2016

By Howard Brown

High purity, high brightness limestone deposits in the San Bernardino Mountains and Mojave Desert region occur in upper Paleozoic carbonate rocks which are part of an upper Precambrian and Paleozoic sequence that unconformably overlies crystalline basement. The Paleozoic strata are divided into formations and members, and correlated with strata of the inner Cordilleran miogeocline. The region has been affected by multiple Mesozoic intrusive, contact, and regional metamorphic events. Structure is complex, and includes polyphase Mesozoic folding and thrusting, and complex Cenozoic structures. The area continues to be seismically active. High brightness (white), high purity crystalline limestone deposits are uncommon because their formation is dependent on several geologic processes which include; 1) depositional environment, 2) contact and or regional metamorphism, 3) folding and faulting, 4) uplift and erosion, and 5) preservation through geologic time. The complex geologic history of the San Bernardino Mountains and Mojave Desert region has allowed the formation of several large high brightness, high purity limestone deposits which are currently being mined or will be mined in the future. Specialty Minerals, Inc. (formerly Ptizer), Pluess-Staufer (California), Inc. and Partins Limestone, Inc. produce high brightness, high purity limestone from several quarries in the San Bernardino Mountains. These active mines combined with undeveloped deposits controlled by Pluess-Staufer in the San Bernardino Mountains, New York Mountains, and Bristol Mountains in the Mojave area, contain proven and or indicated reserves sufficient to sustain production through the 21st century Detailed geologic mapping, intimate knowledge of stratigraphy, recognition of complex structures, sampling, drilling and assay data, are proven tools in the discovery and delineation of high brightness, high purity limestone deposits in the San Bernardino Mountains and Mojave Desert region of southern California.

Jan 1, 1995

By Éder Domingos Oliveira, Leandro Viana Teixeira, Carlos Antonio Morais, Ruberlan Gomes Silva

The purity of rare earth products depends on the ability of the reagents used to selectively promote the precipitation of the rare earth elements (REE) from impurities present in sulfuric liquors. The present study aims at investigating the conditions required to precipitate REE, either as rare earth oxalates or carbonates, from purified rare earth sulfuric liquor with a low Al3+ and UO2 2+ and a very high Ca2+, Mg2+, Mn2+, and SO4 2− impurity content. The rare earth sulfuric liquor was obtained in a previous study by the reaction of a rare earth ore with sulfuric acid, pyrolysis at 700 °C/2 h, cooling at 20 °C, and water leaching. The impurities such as Fe3+, Th4+, and PO4 3− were completely removed from the liquor in two consecutive neutralization steps. In order to recover the REE, the purified rare earth liquor was then treated with oxalic acid and sodium carbonate. Rare earth oxides (REO) precipitated with oxalic acid displayed a very high purity (99.2% w/w) and low impurity content. In contrast, the rare earth carbonates precipitated with sodium carbonate presented a comparatively lower REO content (68.5% w/w) and 94.2% of purity, but with a higher content of impurities. Better precipitating conditions were achieved at 60 °C, compared with 20 °C, and under stoichiometric reagent consumption, with REE precipitation efficiencies higher than 96%. The dosage above the stoichiometric condition caused the precipitation of calcium oxalates and co-precipitation of rare earth sulfates when oxalic acid is used, and precipitation of calcium, manganese, and uranium carbonates and also a co-precipitation of rare earth sulfate when sodium carbonate were used. An integrated flowsheet to produce a high-quality rare earth product from rare earth sulfuric liquor containing some impurities is proposed.

By Éder Domingos Oliveira, Leandro Viana Teixeira, Carlos Antonio Morais, Ruberlan Gomes Silva

The purity of rare earth products depends on the ability of the reagents used to selectively promote the precipitation of the rare earth elements (REE) from impurities present in sulfuric liquors. The present study aims at investigating the conditions required to precipitate REE, either as rare earth oxalates or carbonates, from purified rare earth sulfuric liquor with a low Al3+ and UO2 2+ and a very high Ca2+, Mg2+, Mn2+, and SO4 2− impurity content. The rare earth sulfuric liquor was obtained in a previous study by the reaction of a rare earth ore with sulfuric acid, pyrolysis at 700 °C/2 h, cooling at 20 °C, and water leaching. The impurities such as Fe3+, Th4+, and PO4 3− were completely removed from the liquor in two consecutive neutralization steps. In order to recover the REE, the purified rare earth liquor was then treated with oxalic acid and sodium carbonate. Rare earth oxides (REO) precipitated with oxalic acid displayed a very high purity (99.2% w/w) and low impurity content. In contrast, the rare earth carbonates precipitated with sodium carbonate presented a comparatively lower REO content (68.5% w/w) and 94.2% of purity, but with a higher content of impurities. Better precipitating conditions were achieved at 60 °C, compared with 20 °C, and under stoichiometric reagent consumption, with REE precipitation efficiencies higher than 96%. The dosage above the stoichiometric condition caused the precipitation of calcium oxalates and co-precipitation of rare earth sulfates when oxalic acid is used, and precipitation of calcium, manganese, and uranium carbonates and also a co-precipitation of rare earth sulfate when sodium carbonate were used. An integrated flowsheet to produce a high-quality rare earth product from rare earth sulfuric liquor containing some impurities is proposed.

By Jodie Robertson, Isabel Barton, Cristian Caro

Prior to mining, all rocks contained in a mineral deposit must be placed in one of several categories known as ore types. Each ore type describes a different way that the rock will behave in processing. The ore type determines which process stream a particular mined unit will be sent to, sets expectations for process engineers and metallurgists, and forms the basis for recovery predictions and production estimates. At first, ore types are assigned mainly by geologists based on visible geological criteria (dominant ore mineralogy, estimated grade, rock type, alteration type). As metallurgical tests are carried out and process data accumulate, the resulting criteria may be factored into the ore typing process, typically as assays and recoverable metal using the relevant process(es). Other variables may also be incorporated into ore typing at operations if they are particularly important, such as grindability, preg-robbing, gangue reagent consumption, and the presence of especially deleterious minerals such as talc or smectite. The mine operation department may also redefine ore types and/or process destinations based on economic criteria. A “best” ore type is designated that (in theory) best describes how the rock will behave in processing. Codes representing this ore type are entered into the drill-hole database, then interpreted on cross sections and level plans, and finally added to the block model. Ore types are iteratively reexamined and adjusted over the life of a project. Major difficulties in effective ore typing are (1) lack of communication between geologists and metallurgists, (2) the imprecision inherent in imposing clean categories on messy natural systems without discrete divisions, (3) the need for ore types to provide useful information for a wide range of processes, (4) difficulties in scaling up laboratory test results to mine production, and (5) conflict among geological, metallurgical, and economic criteria for ore typing.

Jul 1, 2024

By Peter A. Spencer

Much criticism has been levelled at bacterial oxidation over the quantities of air required for successful operation. Examination of the oxidation reactions and the assumptions concerning oxygen transfer made in the literature (1) indicate that the aeration requirements can be much less than those beirig suggested. Observations made on a large scale pilot test have confirmed reasonable aeration levels in extended site operation over a six month period. These aeration levels have implications for the engineering design and the power needed for aeration and agitation. Thus, these parameters effect both capital and operating costs as well as influencing the complexity of the design and normal operation. A number of companies have developed bacterial oxidation cultures intended for commercial ·expl oi tat.ion ( 2, 3, 4). Most of these cultures have been based on Thiobacillus and operate at temperatures between 30°c and 40°c. This temperature range limits their application in hotter regions unless means for both heating and cooling are provided in the design. Thiobacil!us cultures are also reported as not able to oxidize arsenic (III), which may limit the application of these cultures to successfully treat arsenopyritic ores and concentrates (5). BacTech (Australia) Pty Ltd has developed a culture which operates at temperatures above 4o0 c and which has been tested in a large site based continuous pilot plant at up to 55°c over a six month period. The culture showed resistance to high levels of soluble arsenic, allowing the arsenic to be retained in solution for control led precipitation and disposal. Data for. the arsenic precipitates indicated that these waste solids were relatively stable and, under the correct circumstances, were suitable for disposal into tailings dams without causing environmental problems.

Jan 1, 1990

By L. K. Holder

"The Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), commonly known as Superfund, mandates evaluation of remediation alternative using nine criteria: (1) overall protection of human health and the environment, (2) compliance with ARARs (applicable or relevant and appropriate standards), (3) long-term effectiveness and permanence, (4) reduction of toxicity, mobility or volume, (5) short-term effectiveness, (6) implementability, (7) cost, (8) state acceptance, and (9) community acceptance. Many states have adopted these or similar criteria for remedy selection under state laws. Although not explicitly addressed in the CERCLA criteria, consideration of sustainability can be incorporated into these criteria. This paper explores how sustainability can be evaluated for remedy selection using the CERCLA criteria. INTRODUCTION Sustainability considerations can be incorporated into all phases of site remediation: • Site investigation (remedial investigation). • Remedy selection. • Remedial design. • Remediation construction. • Operations, maintenance, and monitoring. This paper focuses on remedy selection. Many have looked at remedy selection using sustainability criteria. However, CERCLA and corresponding State programs require remedy selection using mandatory criteria. This paper shows how sustainability can be explicitly considered using the mandatory criteria. REVIEW OF CERCLA CRITERIA First, we review the definitions of the CERCLA criteria. We then explore how sustainability criteria can be fit into the CERCLA criteria. Overall Protection of Human Health and the Environment This criterion addresses the degree to which each alternative is protective of human health and the environment, considering both long-term and short-term risks. Overall protectiveness is a ""threshold"" criterion, in that alternatives that do not achieve adequate protection of human health or the environment are eliminated from further consideration. Evaluation of this criterion is derived from the evaluation of the other criteria (e.g., long-term effectiveness and permanence, and short-term effectiveness). It is not an independent criterion, but more a summary of the overall evaluation."

Jan 1, 2015

By William G. Doepken

After 15 years of production, 91 Mt (100 million st) of ore mined and nearly 227 kt (500 million lb) of molybdenum produced, Climax Molybdenum Co.'s Henderson Mine and Mill are being modernized as a new mining level is brought on line. The $40 million investment in mine development and plant modernization positions the Henderson complex as one of the largest, low-cost primary molybdenum producers for the next 15 years. Henderson history The Henderson Mine and Mill facilities are located on the east and west flanks of the Continental Divide about 80 km (50 miles) west of Denver, CO. The underground mine and surface mill sites are linked by 16 km (10 mile) of railroad tunnel and 8 km (5 mile) of surface trackage. The mine, railroad and mill were built between 1968 and 1976 at a cost of $500 million. Each has operated at various levels of production over the past 15 years. The Henderson Mine was originally developed using a highly mechanized, panel caving mining system. Over the past 10 years, mining methods, equipment and railroad operations have been improved to position Henderson as one of the most productive and lowest cost underground mining operations. At the same time, the mill and concentrator facilities were upgraded to reduce costs and improve product quality. During this time, manpower was reduced from 2000 to 560 employees. These 560 people increased productivity to 54 t (60 st) per total manshift. They reduced operating costs by 50%. And they dramatically improved safety performance. However, as the 1990s approached, the modernization of the Henderson mining and milling complex and the development of the new 7700 mining level became the primary goals to guide Henderson into the 21st century.

Jan 1, 1991

By John F. Shea

When Dick Robbins asked me to give a keynote address, I felt it might be in order to review some of the practices and techniques used in tunneling and work up to some of the concepts now used to mine and construct tunnels. Needless to say, there have been many changes in tunneling technology and also many changes in the Safety Codes controling them. An example of this latter change was the fact that in 1931, my father excavated the Owyhee Tunnel No.5 with gas locomotives. He was able to do it because there was no natural gas in the rock and the ventilation system was designed to free the tunnel atmosphere from powder and exhaust fumes. Today OSHA rules would never permit gas locomotives underground, although there were no incidents on this particular project. One of my first tunnels, as Project Manager, was the Clear Creek Tunnel for the Bureau of Reclamation. Our method of handling muck was the Conway Muckers. This unit was a valuable improvement to the hand mucking of previous generations. The Conway was also used in our Navajo Project, in New Mexico. Unlike the Clear Creek project, where water was one of our main problems - up to 7,200 gallons per minute, at a pressure of 395 pounds per square inch - in the Navajo Tunnel, we had a mixed face which caused a major problem with our support system. In one of the Navajo Tunnels, there was a major cave-in, when the squeezing shale came in during an attempt to strengthen the support system. Although moving shale was not a constant problem, there were areas where the shale was five to six feet above the spring line.

Jan 1, 1976

By Steven Hart, Graeme Hill

Boddington Gold Mine is situated 130km South-east of Perth, WA. The operation is managed by Worsley Alumina Pty Ltd. The Direct Leach plant was commissioned in mid 1986 at a rate of 3 million tonnes per annum. The plant was upgraded to 4.5 mtpa in 1988 and almost immediately to 6mtpa in 1989. Subsequent debottlenecking resulted in further increases in throughput up to 7mtpa by 1991. The SupergenelBasement Plant was constructed in 1990 and commissioned in early 1991. It was designed to process both copper-gold-silver anomalies within the laterite gold orebody and future hard rock ores. The Supergene plant incorporated control potential s­ulphidisation (CPS) and flotation ahead of CIL to remove a host of copper minerals. It operated in that configuration for 2 years at rates up to 350,000 tpa and average grades of 6.0 git gold and 1.2% copper. Gold recovery averaged 90.7% and copper recovery averaged 80.0% before the flotation circuit was decommissioned in March 1993. Quartz hosted high grade, free milling oxide and basement ores were discovered at the northern end of the orebody in 1990 and now comprise the major feed source to the basement plant. Oxide ores are currently milled at a rate of 550,000 tpa, while basement ores are milled at a 420,000 tpa rate. Metallurgical testwork during the feasibility stages indicated that up to 30% of gold in plant feed could be recovered by gravity separation methods. It was also highlighted that signifi­cant improvements in overall plant recovery and reduced operating costs would be achieved by maximising gravity gold recovery ahead of cyanidation. To achieve this, rec;iesign and upgrade of the gravity circuit was necessary.

Jan 1, 1995

By Luciano Ramos, Daniel Santos

Igarape Bahia Mine, which is currently the largest gold producer in Brazil, belongs to Companhia Vale do Rio Doce - CVRD and is situated 250 miles south of Belem, state of Para, Brazil. It came into operation in 1992 with the startup of the CIP plant, fed with high grade ore, presently at 3.4gAu/t. The ore is totally oxidized, containing extremely fine particles of free gold. The ore is soft and low cyanide consumer, with a maximum work index of 12kwh/sht. In 1993 a Heap Leaching Plant was set into operation, handling low grade ore of · 1.s g Ault. The Heap Leaching Plant has undergone two major expansions. In 1994 its capacity was raised from lMtpy to 2,2Mtpy and in 1998, with a thorough remodeling of crushing operations, it was raised again to 3.5Mtpy. The CIP plant, which was originally designed with a capacity for l. lMtpy of ore, was expanded to a 2.2Mtpy capacity in 1994. Presently, the CIP plant accounts for most of Igarape Bahia's total gold output, with approximately 220,000oz per year. Igarape Bahia's annual output is around 360.000 oz. Over the last three years, work has been intensified to improve performance of both processes, aiming at maximizing productivity of the two industrial plants. Reduced costs and increased revenues have been given a special emphasis in the unified improvement program. Cost · reduction has involved developing methodologies to rationalize consumption of materials and inputs, while increased productivity has been given top priority as a means of generating increasing revenues. Thus, all of the improvement and development efforts have had a common goal: to increase operating income.

Jan 1, 2000

By S. G. Malghan, W. H. Moyer

In reference to the section "Excess pyrite," the author discusses difficulties in separating chalcopyrite from pyrite. A technique does exist, and has been used commercially, for the flotation, separation, and recovery, if desired, of both chalcopyrite and pyrite. The method was described in Mining Engineering, March 1966, "An Improved Flotation Method for Cornwall Sulfides." While it was not used on a porphyry copper ore, it was used on a chalcopyrite- pyrite-containing ore and might well have application. Both sulfides, chalcopyrite and pyrite, were floated simultaneously using xanthate as a collector and MIBC frother to produce a cleaned sulfide product. This concentrate was then thickened and conditioned at high solids with aeration and lime to a pH above 12.0 for a period of 1.5 to 2 hr. A supplemental suppressant, such as cyanide, could be used if necessary to sharpen the subsequent separation; however, it was not required at Cornwall. The conditioned sulfides were floated with two stages of cleaning to produce a high- grade chalcopyrite froth product and a pyrite sink product barren in copper. The separation at Cornwall gave a 28.6% Cu grade chalcopyrite product and a pyrite analyzing 0.06% Cu. A desliming step on the raw ore initially used at Cornwall for a period of time was later discontinued. Advantages to be found in using a strong sulfide collector, such as a xanthate, is the rapid flotation it induces and, generally, an ability to float at a coarser grind. A following regrind circuit could be used to give maximum liberation and produce a clean sulfide concentration. The "differential" separation is concerned primarily with grade and with assuring a barren pyrite for maximum recovery.

Jan 1, 1987

By K. G. Tsakalakis

The Greek Cement Industry is a vital sector of our economy. With an annual production of cement over 15.5 million tonnes, it contributes significantly to the national gross domestic product (G.D.P.). The cement industry, as other mineralogical transformation process industries (lime, glass, ceramics, extractive metallurgy etc.), is high energy intensive. Each tonne of cement produced requires not only large amounts of fuels (coal, fuel oil), but additionally a significant quantity of electrical power as well. All fuels consumed by the Greek Cement Industry are imported and energy accounts for one third of the cement production cost. Therefore, it is of interest of the community and the industry to increase energy efficiency, to reduce the quantities of fuels consumed in the cement manufacturing process. It is also known that like almost all manufacturing processes, the cement industry produces large amounts of CO2 (combustion of fuels, de-carbonization of limestone and use to electricity). The utilization of wastes (principally as alternative fuels, scrap tires, spent solvents etc.) is compatible with the general principles of waste management and it is also a common practice in other European and developed countries. In the present paper the economic, social and environmental benefits provided by the recycle process of the various wastes in the Greek cement plants are extensively analyzed. From the whole work, it was concluded that such a practice: - replaces a significant percentage of imported fossil fuels in the cement manufacturing process, - maximizes the recovery of energy and also ensures their safe disposal, - produces overall environmental benefits by reducing releases to air, water and land, - prevents resource depletion of valuable non-renewable fossil fuels, - overcomes the need for the construction of dedicated incineration facilities, - contributes positively to the principles of the sustainable development.

Jan 1, 2003