Search Documents

By Lee W. Saperstien

At the heart of the mining process are a number of basic and fundamental tasks whose regular and repeated performance constitute the mining cycle. As will be discussed presently, these tasks are the basic components of the mining system. Section 9, Production Operations, provides the mine designer and engineer with an understanding of these tasks and with sufficient design principles to allow this person to create an efficient mine system. This section is meant to be an introduction and adjunct to subsequent sections that describe specific mining systems. However, sufficient design information is included here for the independent design of mine systems that may not be described elsewhere or for subsequent verification of existing designs. For the purposes of this section, mining subsumes excavation; thus this material applies to any excavation process. Accordingly, this section is written in general enough terms to include both surface and underground mining. It may be used also for civil engineering excavations that often involve the same steps. Obviously, the actual procedures undertaken in any specific mining system will appear to be very different from those taken in any other system. This is certainly true when comparing surface with underground methods. Yet the fundamental principles are often the same. This segment is written to explicate the basics. Wherever appropriate, the section will suggest the differences between the application process to surface or to underground mining.

Jan 1, 2008

By C. Mark, D. M. Pappas

From 1999 through 2008, groundfall events resulted in 75 fatalities, 5,941 injuries and 13,774 noninjury roof falls in U.S. underground coal mines, according to the U.S. Mine Safety and Health Administration (MSHA). A comprehensive analysis of these events was conducted to better understand where and why these incidents occurred. The first segment of the study used the MSHA database to evaluate groundfall injury rate trends related to mining method, year, locality, seam thickness, mine size, coalbeds and seasonal effects. In the past decade, roof fall injury rates have dropped 50%, but rib fall injury rates have remained constant. Room-and-pillar mines had a roof fall injury rate that was nearly 2.5 times the longwall rate. High groundfall rates occurred in the Illinois Basin, a finding that correlates with other studies that have shown that roof rock in the Illinois Basin is weaker than that in the central Appalachian coalfields. Finally, noninjury roof fall rates in the eastern and central United States were found to be 50% higher from July through September, possibly because of the changes in humidity levels that may cause shale mine roofs to deteriorate. The second segment of the study evaluated the root causes of failure by reviewing all MSHA groundfall fatality reports for 1999-2008. Pillar recovery was the leading cause of groundfall fatalities (19%), followed by rib falls, roof skin falls and traveling under unsupported roof (16% each). Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 1, 2011

By H. Simpson

Middelburg mine is an opencast export mine operating in the Eastern Transvaal Coalfields of the Republic of South Africa (Figure 1). The mine was commissioned in 1983, to its original design capacity of 4.25 million sales tonnes which was subsequently raised to 5.5 million sales tonnes in 1989. This increase in export tonnage was brought about through an increase in the mines export allocation and the revision of management strategies. The maintenance of this increased tonnage with minimal additional capital has been achieved through improved operational efficiencies and the upgrading of planning operations through the purchase of an Enhanced Mine Scheduling Software Package (EMSSP/MINESTAR). Simultaneously with this requirement were additional factors that contributed to the implementation of the EMSSP. The mine was owned by a joint venture of two partners and is operated by Middelburg Mine services (Rand Mines Pty. Ltd) (Figure 2). This structure of ownership required the evaluation of numerous planning options to be under-taken concurrently and hence the need for an efficient streamlined scheduling pack-age that could fulfill this requirement. Compounding the EMSSP needs further, were the problems experienced in the export market, these being the external pressure from current and new suppliers in the market place which obliged management to provide solutions to rapidly changing market conditions. These fluctuating market conditions have had a direct effect upon the mine's planning strategies because of the large percentage of the mine?s sales sold on the international spot market. The sanction factor for all South African exporters has had a negative effect upon price and this was compounded further through internal competition in 1987 via suppliers attempting to maintain the market position.

Jan 1, 1991

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023

By A. M. Anthony, A. Y. Atta, S. S. Magaji, U. Abubakar-Zaria

There are two major gold recovery methods: the hydrometallurgical technique, which employs cyanide solutions, and amalgamation method, which involves mercury (Hg). These methods present considerable health, safety, and environmental concerns. Past applications of alpha-cyclodextrin (α-CD) on gold scraps show that α-CD is not only inexpensive, but is also environmentally friendly. This research work used α-CD to recover gold from gold ores instead of gold scraps. The gold ore was sourced from Shanono gold deposit site Kano State,Nigeria. The gold ore was characterized by fire assay (FA) for the precious metal. The concentrate was digested with aqua regia (AR) for 24 h. Modified AR, where hydrochloric acid was replaced with hydrobromic acid, was used for the gold digestion due to the good match in molecular recognition between gold bromide ion (AuBr)− and α- CD in a second sphere coordination complex. The digestate was characterized using atomic absorption spectroscopy (AAS). Gold recovery using this technique is pH sensitive, and five pH values (2.0, 3.6, 4.0, 5.4, and 6.0) were investigated. FA analysis showed the Shanono gold ore deposit contains an average of 4.71 ppm of gold, AAS analysis showed highest gold recovery of 69% at pH 4.0, which is lower than recoveries from the metal scraps. This could be due to the presence of other gangue minerals closely associated with the ore. However, gold recovery using α-CD on Shanono gold ore has shown to have a higher yield of 69% compared to 35.5% yield obtainable by Artisan Small Scale Miners using mercury.

May 5, 2020

By W. F. McDermott

One of the major improvements in ore grinding economics in North America has been the introduction of autogenous grinding. The history of this has been well documented in previous AIME presentations and in the literature. Pickands Mather & Co. has been very active in the development of autogenous grinding since 1957. This early work led to the application of autogenous grinding to the Wabush Mines ore in 1965, with the installation of 6-24 ft. diameter by 8 ft. long - 1,750 HP mills. Development work recently completed in 1971 on another ore has led to the decision to install 5-36 ft. diameter by 15 ft. long - 12,000 HP mills when this project goes ahead. Between these two decisions lies a tremendous amount of research, development, and application of autogenous grinding to a variety of ores. The Pickands Mather Metallurgical and Research Laboratory in Hibbing, Minnesota has tested, in its pilot plant facility, ores from 9 different deposits. Some of these deposits have as much difference within their own ore types as there is between the various deposits. Therefore, it is safe to say that over 20 different ore types have been tested and flowsheets developed for commercial applications. Of the 9 projects, 3 are in operation. These are Wabush Mines in Labrador, Canada, (1) Savage River Mines in Tasmania, (2) and The Griffith Mine in Red Lake, Ontario, Canada. (3) Pilot plant work has encompassed over 300 individual tests. These tests were carried out in mills that were 5-1/2, 8, and 12 ft. in diameter. Grinding power requirements for the primary autogenous milling has varied from 2 to 30 KWH/Lt of crude ore.

Jan 1, 1972

By Yassine Lahmadi, Edoardo Trivellato, Christian Chereau, Bénédicte Robert

Within the framework of the adaptation of the South-East European Technicentre (Technicentre Sud-Est Européen TSEE), SNCF Voyageurs appointed Pini with the project management mission (MOE) for the design and construction monitoring of a road tunnel. This investment has a dual function: during the site transformation phase, it facilitates the work logistics (and shorten traffic flows); and in the operating phase, it is intended to ease all movements on the site over the long term. This is a limited-length gallery (50 meters) to be performed in conventional excavation below Poniatowski Avenue (Paris 12e). The excavation, crossing the entire width of the boulevard, constitutes a major challenge, given the very low coverage (less than 5.5 m), and the surrounding main infrastructures. The same project mis- sion includes the design of the tunnel accesses, via reinforced-concrete frame structures. The targeted design questions several aspects of its execution framework, and particularly, continuous operation must be guaranteed to the neighboring networks during the works. The installation of an umbrella- pipe all along the excavation profile, the progression in divided sub-sections, and the implementation of a complex monitoring system are hence key elements for limiting and controlling any deformation. An exhaustive 3D finite element modelling was performed, taking into account the detailed phasing of construction (pre-support, excavation in divided section, preliminary support and definitive lining), to dimen- sion the structures, and, overall, to analyze the impacts on the neighboring structures and facilities. During the execution phase (planned for mid-2024), monitoring activities with back-analyses as close as possible to the works are planned.

Jun 23, 2024

By Andrew J. Gaber

Beginning in 1961 the Coal Research Bureau of the West Virginia University School of Mines began a program of research to investigate the potential of the magnetic separation process to remove sulfur of the pyritic form from pulverized coal. Using a so-called isodynamic magnetic separator (1) it was demonstrated that significant quantities of pyritic sulfur could be removed from coal. Pulverized coal samples representing several different coal seams were individually screened into sizes in the 48 mesh by 200 mesh (297 to 74 microns) range, and untreated and steam-air treated samples of each were processed by the magnetic separator. The results of the investigations to magnetically remove pyrite from coal were published in two separate reports issued by the Coal Research Bureau (2,3), The isodynamic magnetic separator was designed about 30 years ago for use in geological and mineralogical laboratories (1,4,5) to isolate one or more minerals exhibiting only small differences in their magnetic propertiese Specifically, to accomplish this, the air gap of the unit was designed to provide a nearly constant magnetic gradient both laterally and longitudinally in the separating zone. It is reported that mineral concentrates of 99.5 percent purity can-be produced on closely-sized fractions after several cleanings through the unit. The isodynamic magnetic separator, therefore, was not expected to process coal containing sizes smaller than 200 mesh, or to demonstrate commercial capability to process pulverized coal. The primary purpose of the Coal Research Bureau in using the unit was that of determining if the magnetic process could remove pyrite from coal, and thereby encourage further research directed toward development of acceptable full-scale processing equipment.

Jan 1, 1969

By Hans G. Machel

In low-temperature diagenetic environments (0 c T c 60 - 80°C), elemental sulfur forms by six common processes: via (1) inorganic oxidation of H2S by molecular oxygen, (2) inorganic oxidation of H2S by ferric iron compounds, (3) polysulfide disproportion- ation; and via the microbial metabolic actions of (4) colorless sulfur bacteria, (5) colored sulfur bacteria, and (6) some types of thiobacilli. Economically viable deposits of native sulfur usually are formed by only one process: inorganic oxidation of H2S by molecular oxygen. The amount of elemental sulfur is also limited by three common processes that destroy it in low- temperature diagenetic environments: bacterial reduction, bacterial oxidation, and inorganic oxidation. In high-temperature diagenetic environments (80 - 10o°C c T c 150 - 200°C), particularly in sour gas reservoirs, there are seven common processes forming elemental sulfur: (1) SOdH2S reaction, (2) H2S- hydrocarbon reaction, (3) polysulfide disproportionation, (4) catalytic H2S decomposition, (5) C02-H2S reaction, (6) chlorinification, and (7) exsolution of physically dissolved elemental sulfur. Natural processes that destroy or remove elemental sulfur in such settings are hydrocarbon sulfurization, polysulfide formation, and advection. In most sour gas reservoirs, relatively small quantities of elemental sulfur occur as a free phase (solid or liquid). However, elemental sulfur often precipitates in copious amounts from the reservoir fluids via exsolution and polysulfide disproportionation during production of sour gas reservoirs. By extension, elemental sulfur may precipitate from reservoir fluids in relatively large quantities upon uplift and erosion of deep sour gas reservoirs, or from advection of sulfurous fluids into shallower settings via faults or other high-permeability pathways.

Jan 1, 1992

By Alexander Sutulov

It is calculated that since the beginning of last century, which practically coincides with the beginning of the Industrial Revolution, our civilization has consumed around 239.5 million tons of copper (see: Table 1). According to the most pessimistic projections of today, with only a 2.5% annual growth rate in demand, we are bound until the end of this century to consume another 200 million tons of copper in remaining 17 years. A recent study made by US Bureau of Mines (1) indicates that the proven ore reserves of 150 major operating mines and about 120 deposits sufficiently explored for development and feasibility studies accumulate a total mass of 49.3 billion tons of ore, assaying an average of 0.82% Cu and containing around 324 million tons of recoverable copper. Consequently, there is a high grade of probability that the bulk of our future ore supplies, for our demand of, say, next 25 years will cane precisely from these mines. The interesting point in USBM study is that it indicates the recoverable byproduct content of these ores and which is: 118.2 million troy ounces of gold 2277.4 million troy ounces of silver 7.1 million tons of lead 24.7 million tons of zinc 1.3 million tons of nickel 3.1 million tons of molybdenum 765 thousand tons of cobalt, and 720 thousand troy ounces of platinum. This information gives us a relatively reliable profile of our future ores for next 25 years, and thus makes possible evaluation of byproduct credits in our future copper mining and producing activities.

Jan 1, 1983

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined, so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits, but this process is subjective and results in quantities of dilution and ore loss that can be improved upon to enhance the profitability of mining operations. In this study, two weeks of production data from a homogeneous copper (Cu) porphyry and heterogeneous manto-type Cu deposit were used to assess the variability in the hand-drawn dig limits of 20 geologists, mining engineers and ore control specialists, which were compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine varied by 3.7 percent, from $10.5 million to $10.9 million, averaging at $10.8 million. The percentage was nearly double for the more heterogeneous mine at 5.9 percent, from $17.9 million to $19.0 million, averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9 percent increase) and $19.3 million (7.0 percent increase) for the homogeneous and heterogeneous deposit, respectively. The natural variability, diggability requirement and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Oct 1, 2024

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By J. D. Crone

Crone Geophysics Limited in co-operation with Newmont Exploration Limited has developed a ground Pulse electromagnetic method. This is the first unit in a planned integrated system of surface and borehole Pulse EM equipment. Newmont had previously developed an operational Pulse EM unit for use in areas of very high surface conductivity. The Newmont equipment was large, heavy apparatus that required motorized transport. It operated in the equivalent frequency spectrum of 10Hz to 2.5Hz. The basic aim of Crone Geophysics was to design a Pulse EM system more portable than Newmont's. We wanted to operate in all types of field conditions including heavily wooded and mountainous terrain areas. We also wanted to record the higher frequency information that is contained in the Pulse EM waveform. There are three reasons why we thought this high frequency information was important in survey applications: (1) Field tests conducted over massive sulphide bodies in the Arizona desert showed that the desert weathering process tended to break down the electrical contact between sulphide crystals. The net effect is to reduce the conductivity of a massive sulphide body, particularly narrow bodies or highly fractured sulphide zones. In order to detect such occurances the higher frequency information is essential. (2) We wanted to be able to detect occurances with sulphide content as low as 5% sulphides that are usually poor to moderate conductors. (3) We also wanted to be able to determine the presence and extent of surficial conductive formations and clay deposits since many airborne EM anomalies are caused by such bodies. If we have the capability of detecting and recognizing these formations we would be able to explain the airborne anomaly.

Jan 1, 1976

By T. J. Lyman, M. J. Robison, W. A. Ruemmele

INTRODUCTION The first phase of the Los Angeles Metro Rail Project consists of 7.1 km (4.4 miles) of subway and stations running through downtown Los Angeles from Union Station to MacArthur Park. Contract A171, the Wilshire/Alvarado Line, involves tunnel construction beneath 7th/Street from the 7th/Flower Station to the Wilshire/Alvarado Station. The project consists of the excavation and lininig of 3000 m (9900 ft) of twin-bore, 6.7 m (22 ft) excavated diameter, 5.5 m (18 ft) finished diameter subway tunnels. The location of the project is shown in Figure 1. The majority of the excavation passed through weak siltstone/ claystone bedrock; although, portions of each tunnel approaching the 7th/Flower Station passed through fine-grained alluvium. Both tunnels were excavated with a digger shield. The project also included the excavation and lining of 6 cross passages, 2 communication rooms and a sump, all at tunnel grade between the two bores. A program of geotechnical instrumentation and building monitoring was performed to detect and document the response of the ground and adjacent structures and facilities to tunnel excavation. The instrumentation program was also intended to provide information that would permit implementation of remedial measures, when and as required, to prevent damage to structures, facilities and utilities along the tunnel alignment. The purpose of this paper is to discuss the ground response to tunneling on Los Angeles Metro Rail Contract A171. This paper presents a description of the tunnel project, the excavation and support method used in construction, the subsurface geology, and

Jan 1, 1989

By J. D. Morgan

The US economy grew steadily in 1989, reaching an annual rate of $5.3 trillion in the last quarter (US trillion=1012 ). The value of domestically processed, mineral-based materials rose 5% to $315 billion (US billion=109). The value of metals produced from US ores rose 14% to $11.6 billion, while industrial minerals rose 2% to $20.2 billion. Recycled scrap was valued at $10 billion. Increasing economic activity stimulated metal prices. Yearly lows and highs were $2.31 and $3.56/kg ($1.05 and $1.62 per lb) for copper, $1.58 and $2.57/kg (72 and $1.17 per lb) for aluminum, 77 and 97 cents/kg (35 cents and 44 cents per lb) for lead, and $1.58 and $2.09/kg (72 cents and 95 cents per lb) for zinc. Many mining and metal companies reported reasonable profits. Consumer demand strongly affects mining because the US economy is saturated with long-lived products. Consumer, mortgage, and Federal debt continued to rise. 250 million US citizens already possess 172 million licensed motor vehicles and 100 million dwelling units. New car production fell 4% to 6.8 million units, while truck and bus production fell 1 % to four million units. New housing starts fell 9% to 1.4 million units. Imports supplied a significant proportion of total US consumption of several important mineral materials. Imports of crude and refined petroleum costing $50 billion exceeded domestic crude oil production. President Bush expressed "strong concerns about this country becoming further dependent on foreign oil." And the Department of Energy held a series of hearings around the country to develop ideas for a "national energy strategy."

Jan 1, 1990

By M. M. Rajkovich, J. J. Zaluski, S. J. Gardner

The telephone rings at 3:20 a.m. and an exasperated voice on the other end says, “There’s been a mine explosion at Mine No. 5 and we have not heard from three units of men!” Twenty-three minutes later, the phone rings again and another panicked voice says, “There’s something wrong at the slurry impoundment, the pool level has just dropped five feet and we’re trying to figure out what’s wrong!” Thirty minutes later, the mobile phone rings and an excited security guard says, “We have reports of thick black water running down both the right fork and left fork of Straight Creek and both seem to be rising in the banks!” As if this isn’t enough excitement, the mobile phone rings again and a stressed company official says, “I just heard a report that black slurry is running out of the portals of XYZ Company No. 2 Mine, which is adjacent to our No. 5 Mine!” Is this all some kind of dream or nightmare? More importantly, however, if this could happen, what on earth do you do? Although we all like to think that “It can’t happen to me,” we all must admit that mine explosions do happen, slurry impoundments can rupture and creeks can flood with black water causing damage to others, including competitors. Your response must be quick, cool-headed, calculated and effective. This paper will examine the issues, concerns and ramifications of this hypothetical “disaster” and then present a systematic crisis management response. While each situation is different, there are general guidelines for forming an effective plan of action.

Jan 1, 2003

By J. C. Norman

The boron review arrived too late for the June issue. The United States was the world's largest producer and consumer of boron compounds during 1993. Boron mineral concentrate and chemical production in the United States totaled an estimated 958 kt (1.05 million st), yielding 526 kt (580,000 st) of B203, according to the US Bureau of Mines. Estimated value was $322 million. This level of production was about 5% less than 1992 revised production figures. The United States continued to provide essentially all its own boron while maintaining a strong position as a source of sodium borate products and boric acid to foreign markets. Domestic employment in the mining and beneficiation of boron products in 1993 was 900 people, about the same as in 1992. That was down from 1988 levels of 1250 people. Total world production of boron in 1993 was about 2.5 Mt (2.75 million st), yielding about 1.2 Mt (1.3 million st) of B203. World production in 1993 was about equal to revised 1992 levels. Production United States In 1993, mines and processing operations in southern California were the only domestic sources of boron mineral concentrates and chemicals. Domestic producers, in order of quantity of production, were: • US Borax and Chemical Corp., which operates an open pit kernite and tincal mine at Boron, CA, producing boric acid and borax products, • North American Chemical Co., which produces boric acid and borax products as coproducts from chemical operations at Searles Lake, CA and • American Borate Co., which produced small amounts of colemanite and shipped from inventories from its operation in Death Valley, CA.

Jan 1, 1994

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By P. Zhang, W. D. Xiao

"A process mineralogy study was conducted to guide the development of a process for the extraction of vanadic oxide (V2O5) and aluminum compounds from bone coal and its ash as well as the production of byproducts. Results show that to extract the targeted metals at higher recovery rates, one must find a suitable agent capable of destroying the structure of the mica and breaking down the lattices in which these metal-bearing minerals occur. For such minerals, metal extraction efficiency is usually low if the approach is simply adding an oxidant that cannot destroy the structure. In this research, a byproduct fluosilicic acid (H2SiF6) at 20 percent concentration from an operating phosphate fertilizer plant was found to be powerful and effective for the leaching of vanadium-bearing minerals such as mica. This environmentally friendly process improved the leachability of valuable constituents in the bone coal significantly, with the leaching rate of V2O5 increased to 94 percent, from 83 percent, and that of aluminum oxide (Al2O3) increased to 75 percent, from 40 percent. X-ray diffraction and chemical analyses showed that the structure of mica can be destroyed using fluosilicic acid either alone or in combination with sulfuric acid. Based on the process mineralogy study, a processing flowsheet was tested, which resulted in a final V2O5 powder product with purity of 99.2 percent and an overall recovery rate of higher than 85 percent. The flowsheet consists of leaching, ion exchange and ammonium precipitation. With this process, various byproducts could also be generated, including aluminum fluoride, cryolite, aluminum sulfate, calcium sulfate, ammonium chloride, sodium chloride and cement admixtures.IntroductionVanadium is an important rare metal broadly used in the production of steel alloys and nonferrous alloys as well as in the chemical field as a catalyst. Vanadium-bearing bone coal and clays are abundant in China, and they contain other valuable metals such as aluminum. Bone coal is a type of carbonaceous shale. The vanadium-bearing minerals mainly exist in mica, kaolin, iron oxides, tourmaline and garnet. According to previous studies (Xiao, 2007; Xu, 1989; Xu and Chen, 1991; Ji and Xu, 1991; Chen and Xu, 1992; Xu and Heng, 1992), vanadium occurs from the isomorphous substitution of V3+ for Al3+ or Fe3 + in the crystal lattices of mica, tourmaline, garnet, dolomite and aluminosilicate minerals. In iron oxide and kaolin minerals, vanadium appears as an adsorption form. The isomorphous substitution of vanadium is more stable in tourmaline, garnet and silicate minerals. Therefore, vanadium in bone coal may exist in three phases: vanadium-containing kaolin and oxides, vanadium-containing mica, and tourmaline and garnet (Xu and Chen, 1993; Xu and Zhang, 1993; Xu and Wang, 1994; Feng, et al., 2005; Lin and Fan, 2001)."

Jan 1, 2015

By M. Fig, J. Brune, C. Strebinger, G. Bogin

"A fundamental understanding of flame propagation characteristics through and around obstacles is needed to accurately model methane driven longwall coal mine explosions originating or propagating in the gob. Experimental investigations of methane flames in horizontal cylindrical reactors with simulated gob (i.e. rock piles) were carried out alongside coupled Computational Fluid Dynamics (CFD) and combustion simulations. Stoichiometric methane-air mixtures were ignited in semi-open reactor vessels of 5cm, 9.5cm and 71cm diameter, all with a fixed length to diameter (L/D) ratio of 8.6. This was done both with empty reactors and also with a rock pile placed at the open end of the reactor. The rock pile length to reactor length ratio was fixed at 0.3, and the rock pile height to reactor diameter ratio was fixed at 0.33 for all reactors. The smaller two reactor experiments were modeled with ANSYS Fluent in 2D. Experimental results indicate that for this geometry a similar acceleration mode occurs across scales: that the flame speeds up an average of 40% as it passes over a rock pile with this profile. The model is able to capture several important features of the experimental results, including the significant increase in velocity, the speedup ahead of the rock pile, and the leveling off of the empty tube flame front propagation velocity. INTRODUCTION Explosions in underground coal mines are among the largest industrial explosions, known to result in the rapid combustion of 20m3 of fuel gas or more [1,2] Coal beds hold methane gas under pressure, and when the pressure is relieved through mining activity some of this methane is released. The methane then mixes with ventilation air and, if not sufficiently diluted, may form a combustible mixture, which may result in an explosion. Several large coal mine explosions have occurred around the world recently. These include the 2014 Soma Mine disaster in Turkey that killed 301 people [3], and the 2009 Heilongjiang Mine explosion in China that killed 108 [4]. Other recent mine explosions, including the 2010 disaster at the Upper Big Branch mine that caused 29 fatalities [5], have demonstrated that explosive gases can accumulate and ignite within and around the gob area of a longwall coal mine and then expand into the active mining face and nearby areas, endangering workers and equipment. If enough combustible gas is involved, the initial flame can accelerate, eventually transitioning from deflagration to detonation [6]. Researchers are developing a fundamental understanding of the evolution of the explosion process from the laminar kernel to the fully turbulent regime, and its propagation through obstacles such as those found in the gob. Researchers also studied the initial development of methane flames and the potential for the development of a detonation."

Jan 1, 2018