Search Documents

By M. E. Poad, M. M. McDonald, J. C. Johnson, W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. This report focuses on mine measurements and calibration of the two-dimensional computer model and is the second in a series of three Reports of Investigations describing the Ross shaft study. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor the shaft. Results of the recalibrated two-dimensional model (UTAH2) confirmed the premining stability evaluation. However, after mining began, concern was expressed because cracks and other signs of ground motion appeared at considerable distances from the area of active pillar mining. In part 3 of the study, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 1995

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 49,875 acres of the 54,833-acre Big Jacks Creek Wilderness Study Area (ID-111-7C) in order to evaluate the mineral resources. The study area is located in Owyhee County, ID, about 15 miles southwest from Bruneau, ID. No mining districts are in the study area, but part of one placer claim, located in 1924, extended into it. The northern portion of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Big Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Samuel P. Harteis

Many mining operations rely on retention bulkheads to provide a barrier between impounded water and active mine workings. However, bulkhead failures can cause catastrophic flooding that puts the underground workforce at risk. Underground observations and evaluations of existing bulkheads indicate that a systems approach is required when building an underground water or slurry retention system. In addition to engineering the bulkhead, the designer must ensure the quality control of materials and workmanship of the bulkhead, the reaction of the mine strata when exposed to water under pressure, and methods to monitor the performance of the retention system. Researchers from the National Institute for Occupational Safety and Health (NIOSH), with the assistance of the Mine Safety and Health Administration (MSHA), conducted an extensive review of bulkhead permits submitted to the MSHA Technical Support office in Bruceton, PA. In addition, the researchers visited accessible bulkhead installations at undeground mining operations to gather information related to construction practices, maintenance issues, and monitoring and emergency response procedures. Several key items were identified that must be considered when permitting the installation of an underground fluid retention system.

Jan 1, 2008

By J. J. Taber

Gas and water permeabilities of a large number of samples from the Pittsburgh and Pocahontas coals were measured at various overburden and mean flow pressures. A wide variation in the air and water permeabilities was obtained for each type of coal. Overburden pressure has the most significant effect on the single-phase permeability. Considerable hysteretic effect was observed for both air and water permeabilities. Gas permeabilities are affected to a lesser degree by mean flow pressures above atmospheric. However, at subatmospheric mean pressures, appreciable increase in permeability occurs for low permeability samples. Air and water relative permeabilities were also measured for numerous samples of Pittsburgh and Pocahontas coals. Tests were performed under steady-state conditions for both drainage and imbibition cycles. Results indicate that the flow of gas is greatly reduced during the latter process, whereas it is largely undiminished over a wide water-saturation range during drainage. It is also shown that imbibition saturation distributions obtained from liquid-water imbibition as opposed to water-vapor adsorption produce gas permeability curves of radically different character. The effective permeabilities to both gas and water were significantly reduced with the application of overburden pressures in the range of 0 to 1,000 psig, but the general shapes of the relative permeability curves remained the same.

Jan 1, 1974

By G. L. Fitzpatrick

A portable optical instrument for performing multispot laser vibrometry is described. The instrument is capable of measuring arrival times, surface motion frequency, and surface velocity and displaying these quantities in various useful ways. Sigma Research is currently pursuing the development of such optical measuring systems for the evaluation of structures in rock by non-contact interferometry methods. This work was sponsored by the U.S. Department of Interior (U.S. Bureau of Mines) under a Small Business Innovation Research (SBIR) contract number J0145075. The goal of the work was to develop a portable tripod mounted measuring system which can be set up at arbitrary distances (up to 30 meters) from a surface and project four in-line laser sample beams on this surface. A light receiving telescope gathers the scattered light from these four spots and provisions are made to mix this light with a reference beam from the laser. Four photodiodes are employed to determine the resultant interference signals which characterize the motion (particle velocity, frequency, amplitude) of the four illuminated spots on the surface under sudy. Information of this type can then be used to characterize the elastic or mechanical properties of the surface in question. In some cases (if more than four spots are involved) this surface information could be back propagated to draw inferences about the internal state of the material volume bounded by this surface.

Jan 1, 1987

By L. H. Wullstein

Nitrogenase activity (C2H2 reduction) was found to be associated with the following grasses in the field: Agropyron dasystachyum, Agropyron smithii, Aristida purpurea, Oryzopsis hymenoides and Stipa comata. Uptake of fixed nitrogen was also demonstrated for these grasses. Two unidentified nitrogen fixing bacteria were isolated, one from Stipa comata and one from Aristida purpurea. Cynodon dactylon and Agropyron cristatum were successfully inoculated with the unknown isolate obtained from Stipa comata. The inoculated plants exhibited nitrogenase activity (C2 H2 reduction) whereas uninoculated controls gave negative results.

Jan 1, 1982

By William G. Pariseau

A brief description of a two-dimensional elastic-plastic finite element program intended for mine stability analysis is presented that includes detailed instruction for input data preparation and how to obtain output.

Jan 1, 1978

By William E. Sopper

Heat-dried municipal sludge was applied to a barren burned anthracite refuse bank in 1974. Sludge was applied at rates of 0, 40, 75, and 150 dry metric tons per hectare" Ten species of trees were planted and five species of grasses and legumes were seeded for evaluation. One plot was also irrigated with sewage effluent. The 150 t/ha sludge application rate produced the best overall herbaceous vegetation growth response. The 40 and 75 t/ha sludge application rates produced the best tree seedling growth response. Foliar analyses for trace metals indicated no phytotoxity problems. Analyses of leachate water at the three-foot soil depth indicated that the sludge applications did not impair water quality. Results of the study indicate that treated municipal sludge can be used to revegetate land disturbed by mining activities without adverse effects on the vegetation or water quality.

Jan 1, 1978

By J. A. Organiscak

In the United States, respirable coal mine dust exposures are limited to a 2 mg/m3 time weighted average for a working shift. If the silica content of the sample exceeds 5 percent, the 2 mg/m3 standard is reduced according to 10- (% silica) to limit silica dust exposures to 100 µg/m3. Examinations of dust sampling data collected by the federal coal mine inspectorate showed that roof bolter occupations continue to be at risk for overexposure to respirable silica dust. Testing at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health assessed the effectiveness of a canopy air curtain for controlling occupational exposures to respirable silica and coal dusts. Initial testing found that zones of higher velocity airflow shrank as distance beneath the canopy increased. This suggested that protection from occupational dust exposures would likely decrease as distance beneath the canopy increased. Further testing revealed that coal dust reduction efficiencies were most affected by changes in interference air velocity and, to a lesser extent, changes in canopy air quantity. However, respirable silica dust percentages under the canopy were not affected by such changes and, in fact, were not significantly different from silica percentages measured outside the canopy. This implied that the air curtain was equally effective on both respirable coal and respirable silica dust particles.

By James Noll, Sam Janisko

Underground miners are exposed to some of the highest levels of diesel particulate matter (DPM) in the United States. Therefore, it is important to monitor the exposure of miners to DPM, but it can be difficult because of the complex composition of DPM and the number of interferences. Currently, elemental carbon (EC) is used as a surrogate because it makes up a significant fraction of the DPM and is not affected by interferences. Standard measurement methods for EC can be time consuming and only record end of shift results. In this research, a laser absorption technique that enables one to measure EC concentration in near real time was shown to be a beneficial tool. The real time data showed that the fresh air being drawn into a stone mine was not properly reaching the working area and needed to be redirected to decrease DPM concentrations. The real time data also provided a more accurate efficiency ofan environmental cab compared to just using the standard method by detecting the opening of the cab's window and door. The EC optical monitor was also worn by researchers in a mine to show how it can give not only the average concentration for the shift but also reveal when and where a miner is exposed to DPM. Keywords: Laser absorption, diesel, elemental carbon, mining, exposure

By W. D. Bensema

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550-and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By C. O. Karacan

Underground longwall mining of coal causes large scale disturbance of the surrounding rock mass. The disturbance can increase the rock mass permeability through a reduction on the stress as well as formation of new fractures in the rock. Methane gas contained in the disturbed rock mass can migrate towards the low pressure mine workings and present an explosion hazard. This paper describes the application of a finite difference program to develop a geomechanical model that predicts permeability changes within the rock mass. The calculated permeabilities are used as input to a reservoir simulator that models methane desorption from the coal matrix, methane release from the rock layers and flow towards the mine excavations. The model also considers the basic characteristics of the mine ventilation network. The geomechanical model uses empirical relationships between fracture permeability and stress to calculate permeability changes around a longwall face. The extent of rock failure is determined using a strain softening model that considers both rock matrix and bedding plane failure. The cave rock (gob) is modeled as a compressible, granulated material. The calculated horizontal and vertical permeabilities around the longwall face are averaged and used as one of the inputs to the reservoir model. The reservoir model was developed and calibrated against records of methane flow at a study mine in southwestern Pennsylvania. Good correlation between actual gas production and model outputs has been achieved. The modeling approach provides a basis for estimating methane inflow and optimizing control measures.

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract S0122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine.

Jan 1, 1974

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10- to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 1993

By Russell A. Schreiner

In conjunction with the Geological Survey, the Bureau of Mines conducted a mineral investigation in 1981 and 1982 of the Santa Rosa Mountains Wilderness Study Area (WSA), Riverside County, California. The Bureau of Mines is responsible for the mineral survey of mines, prospects, and mineralized areas in and near the WSA. A literature search was completed to obtain information concerning mineral occurrences and mining activity that relate to the WSA. A field investigation inside, and up to 1 mi outside, the boundary of the WSA, disclosed one prospect. This prospect was surveyed by compass and tape, and five samples were taken to determine the representative mineral content. No attempt was made to expose concealed mineralization or to re-open caved workings. All five samples were analyzed by fire assay for gold and silver and by colorimetric methods for tungsten. Two of the samples were analyzed by semi quantitative spectrographic methods to determine if any unsuspected elements were present. All analyses are furnished in this report except for the semi-quantitative spectrograhic analyses. Complete sample analyses are available for public inspection at the Bureau of Mines, Intermountain Field Operations Center, Building 20, Denver Federal Center, Denver, CO 80225.

Jan 1, 1983

By Harry W. Campbell

A mineral survey conducted by the U.S. Bureau of Mines in 1983 identified no mineral resources in the Beaver Meadows, Blind Horse Creek, Chute Mountain, Deep Creek/Battle Creek, and North Fork of Sun River Wilderness Study Areas (WSA's). A prospect east of the Beaver Meadows WSA has low potential for lead resources. Sand, gravel, and limestone occurrences are numerous in the WSA's; however, similar or better quality materials outside the areas are abundant and more accessible to potential markets. Impure coal and titaniferous-magnetite occurrences are near the WSA's, but are not known to occur within these areas. In 1983, there were 7,025 acres leased for oil and gas within the five WSA's; no current mining claims were in or near any of the WSA's. Evidence of mining activity was found at only one prospect in the WSA's. It is inside the Deep Creek/Battle Creek WSA; no resources or resource potential were identified at this prospect.

Jan 1, 1984

By R. L. Mazza

This final report on methods of reducing and controlling methane in coal mine gob areas indicates that vertical degas holes are beneficial to the mines of northern West Virginia working the Pittsburgh Coal. The USBM funded project involved the drilling and testing of eight vertical holes (four over longwall panels and four over room and pillar panels) based on a review of 13 previously in existence. Areas of observation included gas production history, flow entry profile, underground methane reductions, strata separations, and casing loads (accompanying subsidence). Observations led to the drilling of successful holes drilled short of the mine. Eleven gas production response to applied vacuum tests were conducted at nine degas holes under the contract. Significant production responses were recorded over longwall gobs.

Jan 1, 1977

By R. Karl Zipf, Suresh Bhatt

Highwall mining is an important coal mining method. It appears that upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mines Safety and Health Administration (MSHA) data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwall miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Best practices to avoid trapped miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system. Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By G. Roger Miller, Kristine M. Krajnak, Stephen S. Leonard, Stacey Waugh

Repeated exposure to hand-arm vibration through the use of vibrating hand tools can result in the development of the disorder known as hand-arm vibration syndrome (HAVS; (1,3)). One of the hallmark symptoms of HAVS is cold-induced peripheral vasospasms that result in finger blanching (4). Although the vascular and neural pathology associated with vasospasms has been described, little is known about cellular mechanisms leading to this damage (4). To understand how vibration may alter vascular and neural physiology and anatomy, rats were exposed to a single bout of tail vibration and the molecular responses of neural and vascular tissues were measured to determine if there are immediate or sustained affects of vibration that may underlie longer term changes in physiology. Methods Experiment 1. Male Sprague Dawley rats (n = 32, 6 weeks of age) were housed in AAALAC accredited facilities. All procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guidelines for care and use of laboratory animals. Vibration exposures were performed by restraining rats in Broome-style restrainers, and securing their tails to a vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control rats were treated in the same manner, except that the tail platform was mounted on isolation blocks and not on a shaker. The vibration exposure was 125 Hz, 49 m/s2, for 4 h. Rats were euthanized with an overdose of pentobarbital (100 mg/kg) 1 h or 24 hours after the exposure. RTqPCR was used to measure transcript levels for endothelin 1 (ET-1), the 3 forms of nitric oxide synthetase (NOS) NOS-1, NOS-2, NOS-3 and norepinephrine receptor subtypes 1D, 2A, 2C, in artery tissue, and to measure calcitonin gene-related peptide (CGRP) and nitric oxide synthase-1 (NOS-1) in ventral nerves. Data were analyzed using 2-way ANOVAs. Experiment 2. Male Sprague Dawley rats (n =24, 6 weeks of age) were maintained as described above. Animals were exposed to a single bout of restraint or vibration. Another group of animals served as cage controls. All animals were euthanized 24 h after the exposure, and tail arteries were isolated and frozen. Reactive oxygen species ROS) were measured using electron spin resonance spectroscopy (ESR). Arteries were homogenized over ice in 1 ml of PBS with protease inhibitor cocktail, using a tissue tearer (Biospecs Products Inc. Racine, WI USA). The sample was split into two 0.5 ml samples. One set had PBS and the spin label hydroxyl-TEMPO [0.1 mM] added while the other set had hydroxyl-TEMPO [1.0 mM] plus the specific hydroxyl radical scavenger, dimethylthiourea (DMTU), added to confirm the presence of the hydroxyl radical. Samples were vortexed and then placed in a flat cell for ESR analysis. The ESR spectrometer settings were: receiver gain, 6.32 x 102; time constant, 0.02 s; modulation amplitude, 1.0 G; scan time, 20 sec; magnetic field, 3490 ± 100 G (2). Data were analyzed using 1-way ANOVAs.

Jan 6, 2006