Search Documents

By U Nyberg

Peak particle velocity (PPV) and distance measurements from a single-charge blast test conducted by Swedish researchers in iron ore at the Kiruna Mine in northern Sweden are presented. They are used along with theoretical PPVs calculated using an equation based on hydrodynamics to determine a damage distance range caused by a single charge. This equation, which relates PPV to explosive properties, charge geometry, and distance from a charge, was then applied to a charge of different geometry that was used in drift rounds. A comparison between calculated and measured PPVs suggests that the stoping holes likely damage the easer hole locations, and the easer holes produce damage to the perimeter hole locations. The practical effect is that typical damage limit predictions based on measurements conducted in fresh or undamaged rock are conservative. This suggests that even when perimeter control is not exercised in drifting (i.e., the perimeter holes are fully loaded), the resulting damage may be less than normally expected due to the wave damping effect of the pre-damaged rock. Due to the damping effect, poor perimeter blasting practices are somewhat self correcting. However, it must be strongly emphasized that well-engineered blast designs with perimeter control are highly beneficial in relation to both economic and safety aspects.

Jan 1, 2011

By V R. Sastry, D P. Singh, N R. Thote

Rock parameters which are uncontrollable impose restrictions on the procurement of desirable fragmentation. Blast design parameters which are controllable prove to be important tool in blasting operations. An attempt was made by the authors to investigate parameters which causes big oversize boulders in overburden blasting. A case study of coal mine is discussed in this paper.

Jan 1, 1995

By R Heater, G Glynn

Various small diameter commercial grades of slurry and emulsion explosives were tested and compared. Velocity diameter curves for confined and unconfined charges were established and the effects of temperature and hydrostatic pressure on critical diameters and minimum primer weights were determined.

Jan 1, 1984

By Leslie Taylor, Kevin Genson

This paper reports on an experimental study of the effect that bottom shaping might have on the impulse delivered to a light armored vehicle due to a buried mine detonating beneath the center of it. The study was restricted to explosives buried in saturated sand and three parameters were varied within the study: bottom angle (0 degrees to 21 degrees), depth of burial of the explosive (1.02 mm to 12.7 mm), and stand off distance (0 mm to 38.1 mm). Six hundred and thirty six milligrams of explosive was used as the explosive load. It has been shown in previously published work [1,2] that Hopkinson scaling works well for the determination of impulse loading on a semi-rigid target plates. Therefore in terms of a full scale test using 4.54 Kilograms of explosive the parameters investigated would cover a DOB of from 19.56 mm to 243.84 mm and a Stand off distance from 0 to 734.06 millimeters. These values nicely cover those of interest to the Marines with regard to the AAV (amphibious assault vehicle). Four angles were investigated at all DOB’s and Stand off distances – 0 degrees, 7 degrees, 13 degrees, and 20 degrees. The results show that reduction in impulse delivered to the target is achieved with an angled bottom on the target plate with a major reduction occurring before the 13 degree angle is reached. Hence vehicles with quite modest bottom angles could help greatly in load reduction with very little loss in utility.

Jan 1, 2008

By Ruilin Yang

This paper presents a fragmentation model for large production blasts. The model uses peak particle velocity (PPV) induced from the blast as a controlling parameter to predict the fragmentation size distribution. The PPV can be related to shock pressure or strain under a given rock condition. The fragmentation size is calculated at three-dimensional grid points within the blast volume. The grid size defines the calculation resolution of the model. The fragment size distribution is assumed to be in the same form as the crack distribution within a cube (of the size equals to the grid size) surrounding a grid point. The crack distribution in rock from impact is based on the finding from previous researchers (Seaman et al., 1976). The fines and oversized blocks are calculated explicitly. The summation of the size distribution at all calculation grid points over a specified volume of the blast yields an overall size distribution for the volume.

Jan 1, 2015

By R Yang, D B. Kay

"Blast vibration control is of vital importance for tunnel blasting in urban environments. A vibration model with multiple seed waveforms (MSW) as input for a point of interest was developed in recent years by one of its authors. The MSW blast vibration model has been applied successfully in open cut and quarry blasting situations. From the literature, it appears that there may not be any seed wave-based vibration modelling work for tunnel blasting.A project was conducted to test the MSW model for tunnel blast vibration. A series of tunnel blast rounds were fired and tri-axial vibration waveforms from the blasts were recorded with several seismographs at distances ranging from 10 to 100 metres from the blasts. Seed waveforms were collected and the charge weight scaling law for the signature hole PPV were established.The MSW model is applied to tunnel blasting and specific issues associated with tunnel blast vibration addressed, such as variable effects of confinement and screening to vibration during a blast round. The capability of the model in terms of the PPV and frequency prediction is demonstrated in the paper. The paper demonstrates that the MSW blast vibration model is a useful tool for managing tunnel blast vibration with the potential to optimise round by round design in terms of managing the vibration below the limit while maximising tunnel advance rate."

Jan 1, 2011

By Edward J. Jr Walter, Edward J. Walter

The vibration problem is approximately fifty years old. The original investigation of the U.S. Bureau of Mines was begun in 1930. Significant investigation into the problem was done by Crandell, Langefors, et al, Edwards and Northwood, and again by the Bureau of Mines. This resulted in an effective Safe Limit standard expressed in particle velocity as 2.0 inches per second.

Jan 1, 1979

By Michael Louis, Charles Dowding

Concern over construction vibration-induced cracking has led to development of a new approach to vibration monitoring called autonomous crack measurement (ACM) and illustrated in Figure 1. This paper describes the concept as well as sensor performance in the first test house fitted an ACM system. Response of three cracks in this concrete masonry unit (CMU) house was measured as part of the system verification. ACM employs a single sensor that measures both weather-induced micrometer changes in crack width and those produced by habitation and ground motioninduced vibration. This comparison is displayed in real time via the Internet without human interaction. Graphic display through the Internet provides a new pathway for communication with the public. Such visual comparison of changes in crack width provides a simple alternative to the present system of comparison of measured and allowable vibration time histories. Measurements reported herein show that weatherinduced response of cracks is greater than that caused by presently allowable construction-induced vibration.

Jan 1, 2003

By Jean M. Bouvet, Pierre M. Vuillaume

There is not just one ANFO: ANFO explosive behaviour depends significantly on the blasting conditions and on its physico-chemical characteristics. For instance, ANFO effficiency increases whereas AN porosity is higher and consequently loading density of the explosive is less. This can be argued against generally admitted ideas. Therefore, the efficiency of industrial explosives related to ANFO (for example "relative weight strength" or "relative bulk strength") is a tool that must be used with caution.

Jan 1, 1993

By Split Engineering Chile Fernando Fernandez

Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations.

Jan 1, 2015

By Michael S. Wieland

This report discusses measurement techniques utilized in and trend results obtained from research on delay blasting malfunctions in underground coal shots at the U.S. Bureau of Mines. Charge malfunctions occur during delay blasting in underground or surface mines, rendering the explosive operations more hazardous and less productive. Modern instrumentation techniques reveal several types of reduced charge performance, resulting from cross-hole interactions. Two receptor (wave-target) charge malfunctions were detected in fourteen shots that were undeniable. There were other receptor charges that exhibited under-performance by registering out-of-tolerance or noticeably reduced detonation rates. Delay blasting generates tremendous shock waves and rifting forces that fracture and heave the surrounding stratum and unfortunately damage remaining unfired charges. This report contains two graphs, representing roughly 1% of total records, that show donor (wave-source) charge shock waves and rift (reaction-to-heave) compressions. These debilitating wave impacts precipitate modes of reduced charge performance ranging from weak detonations or misfires to sympathetic detonations. As recognized from previous research, impaired charges react poorly, perform less useful work, and yield fumes with atypical higher toxicity.

Jan 1, 1995

By Frank Hirthammer

Over the past few years, development and implementation of digital logistics solutions has convinced users of many additional advantages of this technology. Barcode labeling and reading increases the company’s efficiency and safety by reducing handwritten documentation and preventing misinformation. Sustainable information and productivity management is a significant advantage in competition. Since manufacturing information is tracked throughout the whole supply chain until the final consumer, all processes become transparent what ensures efficient risk tracking, correct disclosure to authorities (if required), and the compliance with company rules.

Jan 1, 2018

By Andrew F. McKown

Overbreak and damage to rock walls at the perimeter of rock excavation can lead to safety problems due to rock falls and additional costs due to a] extra mucking, b] extra concrete or shotcrete to backfill overbreak, c] additional rock reinforcement, d] additional water inflow and e] additional maintenance of rock walls. To minimize these undesirable effects, there are several perimeter control techniques available (i.e. line drilling, cushion blasting, pre-splitting, smooth blasting, and fracture control blasting) which control perimeter hole spacing, burden and loading to provide a smooth, stable excavation contour. Conventional perimeter control loading and hole spacing is satisfactory for massive, homogeneous formations, but when blasting in weathered or fractured rock closer spacing and very light loading is required.

Jan 1, 1984

By Ruilin Lang

This paper presents an application of 3-D plots and non-linear regressions to define a sitespecific form of the charge weight scaled distance. The PPV (PPA) of single hole blasts is normally considered as a function of two independent variables - the charge weight and the distance. It is of great importance to obtain the relationship of the function accurately for a concerned site in terms of blast vibration analysis and modeling. However, in pre-computer time it was difficult to plot 3-D graphs. Consequently, a charge weight scaled distance was used to plot the PPV (or PPA) against the scaled distance as 2-D graphs. Blast vibration investigators use several forms of the charge weight scaled distances to plot data. We can exemplify them with the cube root of charge weight scaled distance, the square root of charge weight scaled distance, and other forms (Hossaini and Sen, 2004). Each of these scaled distances assumes relative contributions of the charge weight and the distance to the vibration attenuation. For example, the charge weight is assumed to have a less contribution to vibration in the cube root scaled distance than it is assumed in the square-root scaled distance. In reality, for different sites the relative contribution of the charge weight and the distance may be different and site-specific. This may explain that in some cases, the blast vibration data plots using these charge weight scaled distances are scattered. This could be largely due to the fact that the definition of the form of the charge weight scaled distance is not adequate for the particular site condition.

Jan 1, 2006

By Greg Wyartt

Although electronic detonators and blast initiation systems have been commercially available for several decades, uptake in the Australian mining industry has been very slow when compared to other global mining regions. The safety and operational advantages of electronic initiation are generally well understood in Australia, however there has been a prevailing perception that these advantages do not outweigh the extra financial and technical investments.

Jan 1, 2019

By Shazad Hosein, Bill Birch, Catherine Johnson, Toby White, Liam Bermingham

Air overpressure (AOP) from blasting can give rise to a significant number of blasting complaints from residents living adjacent to blasting operations from mines, quarries or civil engineering projects. High amplitudes of AOP are usually associated with the lateral movement of a vertical free face, but it can also be caused by the upward lifting and the venting of gases through the surface of the blast area.

Jan 1, 2018

By Michael Wieland

Smoke/fume measurements from rapid transitory charge reactions are not wholly comparable with thermodynamic reaction code (TDRC) results, since quenched chemical reactions yield nonequilibrium concentrations. Though the work output and major reaction products are usually rendered with minor deviations, the toxic fumes and other minor concentrations reveal some major discrepancies. Work output for charge formulations in underwater or fixture tests were theoretically resolved with work-principal models that form a rough thermodynamic trajectory. Stalled nonequilibrium concentrations are rationalized by finding the underlying quenched reaction(s). The wide relevance of the Zeldovich radical-chain mechanism that transforms nitrogen oxide was previously recognized. The work-principal model (WPM) represents reaction quenching with off-trajectory constraints to render the fumes, without noticeably readjusting the work process. When restraints that characterize the confinement are WPM tractable, the resolution of critical reaction mechanisms is worthwhile, since they remain useful, regardless of the rich, neutral or lean stoichiometry of the charge formulation.

Jan 1, 2012

By Eric Grigoryan, Wade Hutchison

An engineering study of 2,250 blasting damage claims from 1999 to 2008 in Tennessee, Kentucky, Virginia, Nevada, California, Georgia, South Carolina, North Carolina, Alabama, Arizona and Utah were investigated over the last decade and these investigations determine that blasting ground vibrations damage claims are valid less than 1.3 percent of the time. This study determined that valid blasting damage occurred as a result of impact damage associated with fly rock, air concussion stressing, instantaneous reverse stressing associated with ground vibration and crater zone soil shifting related stressing.

Jan 1, 2009

By Carlos Pañura, Michael Geldres, Alejandro Rojas

In this current era of production in large volumes of surface mining, which demands the realization of large-scale blasting, the mining industry must deal with the impact of the vibrations generated by the detonations that are carried out daily in the mines. In this context, the need arises to minimize and control the impact produced by vibrations by determining the interference times of each generated vibration waveform. The vibration waves are produced by the detonation of the explosive charges of each blasthole, analyzing the vibration waves produced by each blasthole, allow us to determine the optimal time between the detonation of each blasthole to reduce the vibrations of the production shot. Once the optimal time is found, it is possible also, to predict the vibration of the production shot (considering times and sequences) using predictive models. The waveform recorded includes information regarding the particle velocity and the dominant frequencies of the vibration. To determine the time between holes, a graph was constructed with the values of the vector Sum VPP (m / s) vs Time between blastholes (s), once the time between blastholes “t” was found, the simulation of the output sequences continued in such a way that, by adding the single waves generated by the blasthole, it gave us a record of vibrations with the lowest level of vibrations.

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit. The samples were assayed and tested for reactivity using the Reactive Ground Catalyzed Adiabatic test. Approximately half of the samples were found to be reactive with standard blasting agents. Unexpectedly, some of these were found to be reactive with blasting agents doped with urea to act as an inhibiter. Relationships between element grades and reactivity and between Specific Heating Capacity and reactivity were developed; however, the small sample size led to these models having an unrealistically large number of geological model blocks tagged as reactive. A program to better understand the behavior by testing more samples was initiated. Drill core was selected based on the predicted level of reactivity using the aforementioned relationships. The samples covered a greater range of grades and lithologies and included rock from the soon to be developed Qanaiyaq pit. The samples were dry pulverized then split for elemental assay, Reactive Ground Catalyzed Adiabatic testing, Specific Heating Capacity (SHC) determination, and X-ray Diffraction (XRD) mineralogical analysis. From this data, a Red Dog Mine specific assay based classification for separating reactive from non-reactive ground was developed. Furthermore, it was possible to divide the reactive ground into two subgroups: i) rock which reacts with ANFO-emulsion blends even when manufactured specifically with a reactivity suppression agent like urea and ii) rock which reacts with ordinary ANFO-emulsion blends only when a reactivity suppression agent like urea is absent.