Search Documents

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c' = 340 kPa (49 psi) and f' = 24°. Residual strengths were determined to be c'r = 0 and f'r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By Derek J. Lennon

Ground conditions in central Glasgow generally comprise loose granular deposits overlying stiffer soils. CFA piling would normally be preferred for urban sites in these ground conditions, but flighting of the superficial deposits has on occasions resulted in building damage. Over the last five years rotary bored piling with vinyl polymer support fluid has proved to be an economic alternative to bentonite slurry. Two case histories in central Glasgow are described in this paper, one for piles founding in granular soils and one for piles founding into bedrock. A comparison is made between the methods required for disposal of the liquid waste from bentonite and vinyl polymer slurries.

Jan 1, 2006

By Raffaella Granata

The paper deals with the remediation of two areas formerly utilized for the disposal of hazardous wastes in a petrochemical plant. The works, designed on the basis of the criteria of maximum safety and minimum environmental impact, consisted in the confinement of the contaminated soil and groundwater within surface caps and perimetrical cut-off walls embedded in the underlying clay layer. The cut-off wall is 0.8 m thick and has a maximum depth of 33 m: it was designed to guarantee, as a minimum, the level of safety for a landfill for hazardous wastes, in accordance with the applicable National Standards. It was constructed with self-hardening mud and with the installation of an HDPE geomembrane. The HDPE liner of the cut-off wall was then sealed to that of the capping to obtain the complete encapsulation of the contaminated soil. A system of piezometers allows the monitoring of the cut-off efficiency measuring the fluctuations of the groundwater table and testing the chemical contents. Some wells installed within the contaminated areas will contribute to guarantee the full efficiency of the system in case of state of emergency, controlling the water-table level inside the confined areas.

Jan 1, 2006

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

A technical exhibition was held in conjunction with the 4th DFI International Conference on Piling and Deep Foundations, Stresa. The exhibition was located in the ground floor of the Conference Hall. It was open from 15.30 on Monday April 8 till 16.30 Thursday April 11, 1991. The following is an alphabetical list of firms who took part. 1) A.P. VAN DEN BERG MACHINENFABRIEK B.V. P.O. BOX 68 8440 AB HEERENVEEN The Netherlands Tel: +31 5130 31355 Fax: +31 5130 31212 Stand Executive: A. Duyfjies

Jan 1, 1994

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By David G. Winter

The Olive 8 excavation site in Seattle was surrounded on three sides by conditions requiring innovation, careful modeling, and extensive instrumentation to support use of a first-of-its-kind shoring system. The solution combined heavy soldier piles, long and steeply angled tieback anchors, and tightly spaced soil nails to support surcharge loads from a 33-story adjacent tower separated by a narrow alley housing critical utility lines. Land restrictions on two other sides of the site also required innovative applications of traditional methods. The Olive 8 project has won three state and local awards for innovation and has been reported on in Engineering News-Record and has been the subject of two feature articles in the Seattle Daily Journal of Commerce. This paper presents the conditions and site challenges, reviews the design analysis, discusses the shoring performance, and looks at other potential applications.

Jan 1, 2009

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

By R. J. Yan

There was a plant equipped with a 32000t Hydraulic Press to be built, under which a box foundation of 22.5m x 15m x 14.25m (depth) with a base slab of, varying thickness was proposed. The subgrade reactions, bending moments and settlements needed to be determined by means of in-situ model test. A model of the same materials as the prototype scaled to l/10 was embedded in-situ with simulated depth in the bedrock. A lot of data obtained from 39 bench marks, 32 elongation measuring points, 30 couples of electric resistance strain gauges and 24 pressure cells attached to the model foundation enables all the quantities required to be found out. Since it was put into operation, the settlements measured has reasonably agreed with the test results and the foundation has been in good condition.

Jan 1, 2010

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By Khamis Y. Haramy

Quality assurance and quality control of drilled shafts has become a concern due to difficulties in accurately locating construction anomalies and determining load bearing capacity of defected drilled shafts. Various non-destructive evaluation techniques have been developed to estimate the integrity of the concrete in drilled shafts. While these techniques have been widely accepted, variables and unknowns can affect the measurement results. Results are typically difficult to interpret, leading to unnecessary construction delays and possible litigation over shaft integrity. In addition, influences of surrounding ground materials, stress states under different load conditions, and crack and residual stress development during concrete curing further complicate determination of shaft performance. This paper focuses on the evaluation of load bearing capacity of defected drilled shafts under various conditions by numerical analysis and modeling.

Jan 1, 2007

By Steven R. Musselman

The bending strength and flexural stiffness of a micropile at its threaded connection is less than its intact strength and may fail due to thread slippage or by fracture through the pin (reduced cross-sectional area of male threads in the threaded zone of the casing). The mode of failure depends on the reduction in cross-section necessary for machining the threads, and details of the threaded connection such as the length of threaded connection, size and shape of threads, and the thread density (threads per inch). Based on data from bending tests conducted on 9-5/8 inch diameter micropile casing, a method has been developed to predict the ultimate moment capacity and initial bending stiffness of round threaded micropile connections. Two modes of failure were observed from four-point bending tests conducted at the University of Illinois on 9-5/8 inch casing with round threads. Threaded micropile casing connections with an effective thread length of 1.35 inches typically failed by slippage at the threads (jump out), while connections using an effective thread length of 1.89 inches failed by fracture of the pin. These two failure modes were described by W.O. Clinedinst in his report to the American Petroleum Institute on tension tests of threaded pipe casing. Clinedinst developed an empirical formula to determine the tensile strength of threaded connections. A method to predict moment capacity for threaded micropile connections by modeling the micropile cross-section and applying Clinedinst?s equation to determine the max tensile stress along the threaded connection while satisfying force equilibrium is proposed. The predicted moment capacity for threaded connections using this approach is within ten percent of measured for both modes of failure observed from the bending tests.

Jan 1, 2007

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2004

By Lok M. Sharma

"Construction of a new bridge in a seismically sensitive area requires careful assessment of earthquake impact on the serviceability of the facility. Not only is the superstructure vulnerable, the foundations play a key role in the bridge’s survivability. A new bridge in eastern part of the state of Missouri in the U.S.A. is located in a seismically active area and hence subject to additional thrust on the foundations and superstructure and potential damage due to liquefaction. An eleven span bridge with foundation soils varying from shallow bedrock to over 30 m (100 feet) overburden soils were considered for the bridge support piers. Two of the bridge support bents located within the flood plain area through over 30m (100 feet) of alluvial deposits were considered most affected by an earthquake event due to the additional thrust and lateral ground spreading. This paper describes the determination of site specific seismic hazard, numerical modelling of the foundation system, and methodology of dynamic analyses, effects of lateral spreading and liquefaction potential on bridge support bents. From numerical modelling using FLAC, the increase in thrust on piers and deformations were computed to predict the behavior of the foundations.INTRODUCTIONA newly constructed bridge on route US 40 crosses the Missouri River west of St. Louis, Missouri and upstream of Mississippi River in mid-west USA. The west abutment area has near surface bedrock while the east abutment area has overburden deposits over 30m (100 feet) thick, mostly river sediments comprising of silts, lean clays and sands overlying bedrock. Softer layers of silts and sands in the east river bank area are assessed to be liquefiable during a high magnitude earthquake event. St Louis area has a potential for a high magnitude earthquake due to the New Madrid Fault some 160km (100 miles) south. The bridge foundations were designed as drilled piers, 2 m (8 feet) in diameter and socketed into the bedrock. Bents No. 10 and 11, located in the lower flood plain area of the river, are considered to be most affected by a seismic event.In order to perform dynamic analyses of the foundations, earthquake ground motion time history was developed for the specific site using a Probabilistic Seismic Hazard Analysis (PSHA) and selecting and scaling of a recorded time history. Relying on the U.S. Geological Survey (USGS) Earthquake Hazard Program for the PSHA and AASHTO Guide Specifications for LRFD Seismic Bridge Design, spectral acceleration values for the site were developed. The spectral acceleration values were for a 7 percent probability of exceedance in 75 years (1000 year return). Numerical modelling using FLAC computer program was performed. This paper presents the seismic design parameters, methodology used in the dynamic analyses, static and dynamic analyses, impact and mitigation of liquefaction on Bents 10 and 11 and the abutment fills, and effect of lateral spreading on the foundations in the lower flood plain area of the bridge. From the numerical modelling, increase in thrusts on pier foundations and estimated deformation were computed."

Jan 1, 2017

By Ken Andromalos

Continued population growth combined with limited water resources in the Denver area has resulted in the conversion of a number of mined out gravel pits in the area into municipal water storage facilities. The use of slurry walls provides a cost effective means of isolating groundwater to convert these pits into efficient water storage facilities. Design considerations include: stability, underlying bedrock conditions, backfill mix design and earthwork requirements. Installation issues during construction include: trench stability considerations when excavating through relatively clean sand and gravel deposits in potentially high groundwater conditions; keying into three to ten feet of fractured claystone, siltstone or sandstone that makes up part of the Denver formation, and quality assurance procedures to assure a proper groundwater barrier is constructed. The paper concludes with two brief case histories to illustrate how these considerations are applied

Jan 1, 2007

By Eugene Mirsky, Eloy Ramos, May ElKhattab, John Wise, Terrence Carroll, Jose Torres

In 2017, Nicholson Construction Company completed a $72.1 million design-build contract for Miami Dade Water and Sewer Department to replace an existing 54-inch diameter pre-stressed concrete force main that runs from the Virginia Key Central District Wastewater Treatment Plant, under the Biscayne Bay at Norris Cut, to Fisher Island. In order to install the new sewer pipe below the bottom of Biscayne Bay, a tunnel boring machine (TBM) was launched from a 42ft diameter and 89ft deep shaft on Virginia Key and a precast segmentally lined tunnel was constructed towards a 28ft diameter and 72ft deep retrieval shaft on Fisher Island. Both shafts were constructed through sand and highly permeable limestone, primarily the Fort Thompson Formation which is part of one of the most permeable aquifers in the United States and two different techniques were used to ensure a water-tight shaft at each end of the tunnel drive. The launch shaft structure was built using the secant pile technique, wet excavation and a tremie plug. For the tunnel break-in a soil freeze block was installed after the ground was treated with low mobility grout. The retrieval shaft was built using the Deep Soil Mixing (DSM) technique and excavated in the dry. Precedence of any other structure built this deep through hard layers (UCS over 3,000 psi) using this technique was not found. This case study addresses the challenges of constructing watertight underground structures in highly porous ground for launching and retrieving a TBM. Design challenges from complex asymmetric loading, selection and comparison of the construction techniques, the installation and excavation of both shafts, and their performance are also discussed herein.

Jan 1, 2018