Search Documents

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By Kenneth Gavin

The accurate prediction of the shaft capacity of drives piles in sand continues to present problems for foundation designers. Research in this field has been carried out for many years and has yielded a wide range of design approaches -some of which have been shown by recent experimental work to be based on questionable assumptions. This Paper reviews some of the current popular design methods for piles in sand in the context of recent information obtained from high quality field tests conducted by institutions such as Imperial College London. A database of driven piles in cohesionless soils has been compiled from well documented (and reliable) case histories that have been reported in the literature. The measured shaft capacities of the piles in this database are compared with predictions made by the various methods and an assessment is made of the predictive performance and reliability of each method

Jan 1, 1996

By B. B. Broms

Embankment piles are common in the Scandinavian countries (Kjellman, 1940) and in Southeast Asia as support of fills, light structures, bridge abutments and deep excavations (Eide, 1968) as described in the following. Untreated timber piles are often used for light structures and shallow fills when the ground water level is high since they are inexpensive and readily available. When the applied loads are relatively high precast concrete piles and steel piles are preferred. DESIGN CONSIDERATIONS Embankment piles carry the load from a fill or a struc-ture either through skin friction along the sides of the piles (Fig. 1a) or through a precast concrete slab or through pile caps at the top of the piles (Fig. 1b). When the load is carried by skin friction it is often economical to use small diameter timber piles because of the large surface area (Asplund, 1939). For precast concrete or steel piles concrete caps are used to transfer the load to the piles due to the relatively high capacity of the piles since the skin friction resistance alone is not sufficient to transfer the load to the piles.

Jan 1, 2010

By Joel Moskowitz

In 1990, the United States General Services Administration (GSA) issued a contract for design and construction of a new federal court building in New York City. Mueser Rutledge Consulting Engineers (MRCE) served as Project Geotechnical Engineers. The project site is in the historic government district at Foley Square. It is surrounded by the New York County Courthouse to the west, an existing federal prison building and federal courthouse across Pearl Street to the south and southwest, an office structure to the north, and a residential tower to the east. The interior of the site was crossed by streets which have now been demapped. As with many urban sites, this site was previously occupied by tenement buildings or industrial structures demolished near the turn of the century. Remains of old building foundations were exposed during construction excavation. In addition, buried fuel oil tanks servicing the adjacent courthouse were removed and the usual assortment of urban utilities had to be relocated for the new building foundations. Ground surface elevations vary from about 4.5 to 6 m above the local Mean High Water Datum Plane.

Jan 1, 1996

By James A. Mason

The State of California has instrumented numerous buildings, bridges, and dams throughout the state with earthquake recording devices. These accelerometers are strategically placed to measure the response of the structure to a specific seismic event. This comprehensive program enlightens the field of seismic engineering after each earthquake. The Office of Strong Motion Studies, California Strong Motion Instrumentation Program, a sub-branch of the Division of Mines and Geology, provides a professional service unequalled in the world. Within hours of a local earthquake, a preliminary report with the epicenter / hypocenter, structural damage, and time history records are available to all interested parties. The included partial report in the appendix, see section 5.1, is one of the reports that C.S.M.I.P. produced after the Loma Prieta Earthquake of October 17,1989. The diagram on the cover is even of interest. This is a small portion of San Francisco. The values on the diagram are the recorded maximum horizontal ground accelerations at that location in the city. For example, the acceleration at Yerba Buena Island was 0.06g. (The "g" refers to the acceleration of gravity. Thus, a 0.06g acceleration refers to the force, F=m*a, that the structure would experience. For this case, the force would be six percent, 6 % , of the mass of the structure.) Yet, directly on the other side of the Bay Bridge, at Treasure Island, the acceleration was 0.16g. Yerba Buena Island is a natural island composed of hard granular material. Whereas, Treasure Island is a man-made island of imported filled. Here one can see the absorption / transmission difference between hard material, which interact with short seismic wavelengths, and soft cohesive material, which interact with long seismic wavelengths.

Jan 1, 1993

GENERAL CONTRACTOR: ALEXANDER CONSTRUCTORS, INC. STRUCTURAL ENGINEER: CAGLEY & ASSOCIATES, INC. GEOTECHNICAL ENGINEER: F.T. KITLINSKI & ASSOCIATES, INC. PILE FOUNDATION CONTRACTOR: L.G. BARCUS AND SONS, INC. PROJECT PROFILE: 108-10 in. diameter AugerPiles installed to an approximate depth of 32 ft. Piles were installed through Stiff Clayey Fill and Medium-Dense Sands to Decomposed Shale. Piles were drilled to a refusal criteria of 1 ft. / 3 min. Piles were installed using a Barcus Mantis AugerPile rig which is large enough to install piles 25 to 50 ft. long outdoors. The Mantis is also ideal for indoor and low overhead installations. On top of being extremely versatile, the Mantis is also very economical to mobilize. The existing structure is supported on H-Piles. The AugerPiles were furnished and installed for less than the material price of the H-Piles. Design loads were under 40 tons which eliminated the need for a load test. AugerPiles were selected for minimal vibration, limited noise, and economy.

Jan 1, 2001

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By Satyajit Vaidya, Rudolph Frizzi, Luis Berroteran

This paper presents design and construction challenges associated with a high-capacity rock-socketed drilled pile foundation system for a 60-story building recently constructed in an urban environment. The site is in very close proximity to surrounding 1-to-6-story buildings and a commuter rail subway tunnel structure. High compression, uplift, and lateral loads imposed by the tall, slender tower constructed over a relatively small site footprint posed a significant design challenge due to the close proximity of the subway tunnel and other structures. Construction challenges included those associated with advancing the drilled pile casings through overburden materials using internal flush method mandated by the Transit Agency, advancing the casings through very dense glacial till materials encountered above top of rock, and drilling rock sockets in variable rock conditions. This paper provides a brief overview of the site and subsurface conditions, and discusses the resulting design and construction challenges for the drilled pile foundation system and how they were addressed. SITE AND SUBSURFACE CONDITIONS The 8,350-square-foot site is located in a busy neighborhood in downtown New York City (NYC). Buildings neighboring the site are supported on shallow foundations, and their basements extend about 15 feet below the sidewalk level. A NYC-Landmarked building is located within a NYC Department of Buildings (DOB)-designated 90-foot influence limit from the Project site. NYC Transit Authority (NYCTA) subway tunnel and station structures are located in close proximity to the Project site. The subway tunnel structure extends about 50 to 55 feet below the sidewalk level. Although the upper portion of the tunnel structure is about 13.5 feet away from the site property line, the lower portion is only about 1 foot away from the property line. A site location plan is presented as Fig. 1. Geotechnical borings revealed subsurface conditions generally consisting of successive strata of surficial fill, sandy and silty soils, and glacial till (predominantly consisting of cobbles and boulders) overlying mica schist bedrock. A generalized subsurface profile is presented in Fig. 2. The surficial fill stratum was about 10 to 23 feet thick, and generally consisted of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick. The underlying sandy and silty soil stratum was about 60 to 79 feet thick and generally consisted of loose to medium dense inter-bedded layers of fine to coarse sand, silty fine sand, and silt. The underlying glacial till stratum was about 26 to 70 feet thick and generally consisted of cobbles and boulders embedded in a very dense soil matrix. Top of bedrock was encountered in the borings about 110 to 150 feet below sidewalk level. Groundwater level was measured at about 30 feet below sidewalk level.

Jan 1, 2018

By David Preece

The Thirlmere aqueduct was constructed over 110 years ago to provide water from the Lake District (in the north-west of England) to the city of Manchester some 60 miles (100 km) away. The aqueduct remains, to this day, a key piece of infrastructure in the distribution of raw water in the north-west of England. A short section of the aqueduct was identified as being in poor condition during routine inspections by the owner. Subsequent investigations attributed the conduit damage to the movement of unstable ground over the conduit. Bachy Soletanche Ltd was subsequently appointed to carry out the design and construction of the slope stabilisation works and to undertake repairs inside the damaged conduit. The works were undertaken on an existing slope which, in places stands at a gradient of up to 40º to the horizontal. Strict limitations on plant and equipment were imposed by the client (United Utilities) to ensure that slope and conduit loading and associated vibrations were kept to an absolute minimum during construction. An intensive instrumentation system was installed to monitor surface movements, ground movements at depth, conduit movement and strains across existing planes of weaknesses within the conduit. The solution comprised the installation of spaced piles up-slope and down-slope of the conduit. Restrictions were imposed on the minimum stand-off distance between the outside face of the conduit and the piling works so targeted permeation grouting was undertaken to improve the ?connection? between the conduit and the down-slope piles. The presence of existing sub conduit groundwater flows was suspected and the permeation grouting was focused in areas to minimize disruption to the groundwater regime. The paper presents the basis of the design and highlights the combined construction and instrumentation methods adopted to minimise damage to this valuable asset.

Jan 1, 2011

By Timothy J. Myers

Expansion and the economic growth in the southwestern region of Missouri necessitated the expansion of State Route 249 and the construction of a new interchange to provide service to the Joplin, Missouri area. The project is located above a former lead and zinc mine in Jasper County, Missouri and includes a five bridge interchange connecting State Route 249 and US Route 171. The variable subsurface conditions, both natural and manmade, prompted the design team to use ground improvement via grouting and small diameter micropiles to provide support for several of the bridge foundations on the project. The scope of work included mine shaft closures, 56,000 ft of overburden and rock drilling, 11,139 ft of micropiles, 524 cy of balanced/stabilized high mobility grouts, and over 8,700 cy of low mobility grout. The selection of the grout used was based on the actual subsurface conditions. Low mobility grout (LMG) was used in voided conditions and for closure of the mine shafts encountered during the excavation. High mobility grout (HMG) was used in fractured rock with the goal of improving the mechanical properties of the rock underneath the future bridge footings and controlling grout volumes during micropile installation. The split spacing method was utilized for both LMG and HMG holes. Geology of the project site subsurface consisted of extremely variable bedrock with strong to very strong limestone, chert, breccia, extremely weak shale, and weak to strong sandstone. Previous activities associated with the mining disturbance (such as partial filled vertical mine shafts, shallow and deep mine horizons, modified hydrology including artesian conditions) further complicates the site subsurface conditions. Real time monitoring and recording of all drilling and grouting parameters was conducted to assist in the evaluation of in-situ geological properties of the site in order to modify the ground improvement and micropile program as necessary. This paper will discuss the design and execution of the ground improvement and micropile program. The project is an excellent example of the use of multiple ground improvement and foundation support techniques combined with real time data analysis to provide a foundation support solution for a complex geological environment.

Jan 1, 2009

By Frank Rausche

Since the early 1980s, when the Road Construction Authority of Victoria authorized the dynamic proof testing of roughly 100 drilled shafts of 1.5 m diameter and typically 60 m length in Melbourne Australia, dynamic load testing has been applied worldwide for quality control of drilled shafts. Today, test capacities of 4000 tons or more are not unusual. On numerous occasions the authors have been involved in similar tests in the United States and test engineers from other countries have reported on experiences in many different countries. Without doubt, generating high test loads is most economically accomplished by dynamic load testing and this method is particularly well suited for testing piles founded in rock because of the rocks low energy dissipation. However, deep foundation professionals have on occasion expressed reservations about subjecting a drilled shaft to impact loadings fearing, for example, a degradation of the shaft ? rock interface properties or potential error sources due to uncertain concrete properties or shaft geometry. This paper will present numerous case studies, demonstrating the performance of rock socketed drilled shafts under dynamic loads. It will discuss the mechanics of the dynamic tests and the method of data interpretation, addressing the concerns stated above and investigating the limitations of the test method. The paper will formulate a set of recommendations for the design and execution of these tests.

Jan 1, 2006

By Virendra Singh

The load settlement behaviour of single pile or pile group may be obtained using computer based methods such as the finite or boundary element techniques. An alternative method of obtaining the vertical soil stresses adjacent to the Pile is presented Based on calculated stresses consolidation settlement for Piles foundation is obtained. This approach may be computationally more attractive than the more general finite or boundary element techniques.

Jan 1, 1996

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By Jelke Dijkstra

This paper presents the results of model pile load tests in a photoelastic material. The soil in this test is represented by an assembly of photoelastically sensitive glass particles, which allows for optical measurements of stresses. In the same test setup, displacements around the pile are measured using digital image correlation (DIC). During the pile installation stresses and strains are recorded. Tests were performed in loose and medium dense particle assemblies. The development of stresses and strains around the pile tip and pile shaft are quantified and presented in this paper. For the loose conditions the results show a small influence on the stress state. For the medium dense conditions a clear stress change is observed.

Jan 1, 2006

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By Amalia Giannakou

This paper utilises 3-D finite-element modeling to study the static and dynamic lateral harmonic response of inclined piles, in a homogenous and a non-homogenous soil, modeled as a linear hysteretic medium. The results of a comprehensive parameter study are presented in the form of dimensionless plots of: (a) static and dynamic swaying and rocking stiffnesses and damping ratios, and (b) distribution of internal forces (bending moment, shear and axial force) with depth. These plots can be readily utilised in practical applications and they offer insight on the role of the inclination in the response of flexible piles.

Jan 1, 2006

By Narong Thasnanipan

This paper presents the outcome of the contest on the prediction of the static axial load capacity of diameter 1.20m bored pile founded at 46m below existing ground. The test pile was constructed by wet-processed method and instrumented with vibrating wire strain gauges. Different methods used by the contestants in prediction of load-settlement characteristics are described and compared with actual load test results. Load-displacement behavior of test pile is found to be better than expected. Major difference between prediction and actual test is the higher frictional resistance of Second Sand Layer achieved in the actual load test. The hyperbolic load transfer method used by one of the contestants was applied to back-analyze the load-displacement characteristics of the test pile at different conditions.

Jan 1, 2006