Search Documents

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

By R. H. Walton

"In recent years the recovery of copper from low grade oxide ores has received widespread attention. The cost of treating such ores using conventional technology, such as milling and flotation, is frequently prohibitively high and copper recovery is generally low. The introduction of heap leaching, solvent extraction (SX) and electrowinning (EW) has resulted in high recoveries, good copper cathode quality and low production costs. This technology has now been successfully applied on a worldwide basis.This paper reviews the various process and design options and gives approximate capital and operating costs for a 1.0% copper ore.INTRODUCTIONAs a result of the low copper prices that prevailed for much of the last two decades, aggressive attempts were made by the industry to cut operating costs. Under such circumstances heap leaching, solvent extraction and electrowinning, to recover low cost copper from oxide ores, has received particular attention and ultimately widespread acceptance.Low grade copper ore (typically containing less than 1.0% Cu), which could not be economically treated by other methods, is placed on heaps and leached with dilute solutions of sulphuric acid. The copper rich, pregnant solution, drains from the heap into a collecting pond and is pumped to a solvent extraction plant where it is purified and upgraded. The resulting solution, termed the pregnant electrolyte, passes to the electrowinning section where the copper is recovered as high grade cathodes and sulphuric acid is regenerated, (Figure 1).This paper specifically describes the processing of copper oxides. Other copper minerals such as chalcocite and chrysocolla are also leached by dilute solutions of sulphuric acid. In practice the oxide minerals are frequently associated to varying degrees with less easily leached sulphides, such as chalcopyrite. In some cases, once the oxidized capping of the ore body is removed, the oxides are totally replaced by more refractory sulphides. Under these circumstances the leaching recovery is significantly reduced. However the principles described here for solvent extraction and electrowinning are also applicable to solutions received from heaps containing sulphide minerals, which are leached more slowly and involve bacterially induced reactions."

Jan 1, 1990

"Automatic flotation control in varying degrees of sophistication is practiced at a number of concentrators throughout the world. Practically, the variable conditions in the flotation circuit and the difficulty in maintaining accurate instrumentation information all add to the complexity of automatic control.Further development at the Kidd Creek concentrator has resulted in a 3075 mtpd copper flotation circuit capable of running twenty-four hours a day under the direct control of an optimizing supervisory computer.Three main streams, continuously monitored by an XRF analyser, supply circuit information to the optimizing computer. Circuit efficiency calculations (from smelter contract terms) and target setpoints allow the computer to determine the economic optimum direction to move the circuit based on the grade/recovery relationship. Circuit manipulation is accomplished by precise pumping of collector and frother reaqents together with accurate control of flotation bank pulp levels. The former uses computer controlled diaphragm pumps and the latter is achieved by control loops utilizing a float type level transmitter, variable position dart plugs and a process computer working to setpoints determined by the optimizing computer.The development of a fully automated flotation circuit is by no means complete, but increased knowledge and major hardware improvements have allowed its progression to a higher level of sophistication."

Jan 1, 1983

By Tapio Leskinen

"In the 1960’s, when large flotation machines appeared on the market, this was a part of a world-wide trend towards the use of ever larger machine units.One factor that has played a decisive part in this development is the increased of the amounts of ore that have to be handled as the exploitation of successively poorer ores becomes necessary. The advancing application of instrumentation and automation has worked in the same direction.In 1970, a working group was set up within Outokumpu Oy, for the purpose of flotation machine development. The principal task of this group was to be the design and development of- a new type of rotor of increased efficiency, especially for the dispersion of large amounts of air- a mechanical-pneumatic flotation machine of substantially larger size that existing plant.This development project required an extensive program of theoretical investigation and experimental studies at several concentration plants of the company.The commonest flotation machine presently used in the concentration plants of Outokumpu Oy is the VK-3. It is of the mechanical-pneumatic type, and the volume of its cell tanks is 2.5 m3 per shaft. This machine was developed within the company, and its first development phase i s represented by the OKKO 3, built for the Kotalahti concentrator in 1959. It was, in its time, comparable in volume to the largest machines that were then in use anywhere in the world."

Jan 1, 1976

By T. Gammatikopoulos, C. Gibson, M. Aghamirian

Lithium is an alkali metal found in brine deposits in the United States, Chile and Argentina, as well as in hard rock deposits in Australia and North America. In hard rock deposits, spodumene (LiAl(Si2O6)) is the major economic lithium bearing mineral. Spodumene is typically upgraded through a combination of dense media separation, flotation and magnetic separation. One of the major spodumene concentrate quality specifications is the iron oxide content because it will help determine if the concentrate is considered ceramic grade for use in ceramics and glass or chemical grade for use in lithium ion batteries. The rejection of iron bearing silicate minerals from artificial ore composites (high amphibole and low amphibole, high quartz/feldspar) from a hard-rock spodumene deposit was investigated using magnetic separation and flotation. The efficacy of Wet High Intensity Magnetic Separation (WHIMS) in iron rejection was found to be dependent on the mineralogy of the iron-bearing silicate minerals including modal distribution, liberation and association. When magnetic separation was conducted prior to flotation, the Fe2O3 grade in the final flotation spodumene concentrate was reduced from ~3% to ~1% Fe2O3 , and improved lithium recovery in flotation was observed. It was determined that it was most effective to conduct WHIMS on the flotation feed after scrubbing and de-sliming because this reduced the required magnetic field to recover iron-bearing minerals, likely because slime coating was greatly reduced. Flotation collector screening of four different collectors with varying rosin acid content demonstrated a potential increase in selective flotation of spodumene over some iron silicate minerals with decreasing rosin acid content in the fatty acid collector. However, due to marginal difference in flotation results with the various collectors tested, further testing is required to confirm the observations made and establish a hypothesis regarding the effect of rosin acid content.

Jan 1, 2017

By Julie Culverhouse, Dennis Grimm, Kieran Harding, Jean-Francois Boulanger

"Agrium’s Canadian Phosphate Business (CPB) is comprised of Kapuskasing Phosphate Operations (KPO) in Northern Ontario, Canada’s only operating phosphate mine, and Redwater Phosphate Operations (RPO) in Alberta, which manufactures the fertilizer from KPO’s concentrate.Production from KPO’s South Pit commenced in 2009 and introduced contaminant problems: high aluminium from crandallite and kaolinite clays. These issues caused a drastic decrease in P2O5 recovery and throughput in both plants. KPO attempted to reduce Al clays by means of aggressive desliming. Meanwhile RPO experienced high amounts of dissolved metals in their feed that are detrimental to fertilizer production.This paper covers the mineralogy of the problem, its impact on contaminant separation at KPO, on RPO’s process and on Agrium’s Canadian Phosphate Business as a whole.Potential solutions to the problem are discussed and analysed, including a process change to deslime high aluminium streams more aggressively and high grade ore flotation, which is atypical at KPO. The latter is a demonstration of the value of communication between the concentrator and the client, as KPO accepted a recovery loss and increased production costs in order to increase overall CPB profits. General lessons learned are discussed, followed by a section on ore blending.INTRODUCTIONAlthough the existence of the Kapuskasing phosphate deposit has been known since the 1970s, it’s only since 1999 that Agrium has been operating the Kapuskasing Phosphate Operations (KPO). The mine consists of three major pits (Center, North and South) from which a mining contractor hauls the apatite ore to the Agrium concentrator. The beneficiation plant processes the ore, separating contaminants such as Fe, Mg and Al which are detrimental to its client, Agrium’s Redwater Phosphate Operations (RPO). The KPO concentrate is finally thickened, filtered and dried before being shipped by rail to RPO.At the Redwater plant, the KPO concentrate is added to a sulfuric acid solution in an attack tank, to create a phosphoric acid solution and gypsum:"

Jan 1, 2011

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

By Sebastián H. Troncoso

Open pit mine planning is normally based on the selection of an economic envelope that has been generated by the Lerchs & Grossman algorithm, which requires individual economic valuation of each block of a geological block model. The selected envelope, usually called Final Pit, is later discretized in pushbacks and benches, which correspond finally to the fractions that the production schedule will allocate in time. This planning methodology has been widely used by the mining industry in countless projects to exploit open-pit mines, however, in many of the deposits can be found some undesirable elements such as arsenic, phosphates, ash among others that tend to reduce the value of elements of economic interest, either by disrupting the processes of concentration or as deemed impurities that affect the quality of the final product. Thus, a fair amount of blending would be required to capture the real value of the ore body. The traditional approach under estimates a block value by penalizing the block value by the amount of contaminant even when at the mine a set of blocks is amine at a time. This paper proposes a methodology for computing cut off grades over time that would maximize net present value allowing blending that should fulfill a set of metallurgical constraints. Preliminary results show significant increases in value and reserves quantity, questioning the use of fixed cut-off grades in generating a production schedule when blending applies to fulfill a set of geometallurgical constraints. Finally, the model allows the authors to show the importance of having adequate planning tools that will lead to the ability to look at the potential economic value of a mineral deposit.

Oct 1, 2009

By S. Banisi, M. Poorkani

The Sarcheshmeh copper deposit contains 1 billion tones of ore averaging 0.7% copper and 0.025% molybdenum. It is located southeast of Iran and currently processes 41,000t/d. Molybdenite as a by-product is recovered in two separate stages. First, a bulk coppermolybdenum concentrate is produced and in the second stage these two are separated. The recovery of molybdenite in the first and second stages is 65% and 85-90%, respectively. The yearly production of molybdenite concentrate varies between 3500 and 4000 t. Sodium sulphide is used as the depressant of the copper and iron bearing minerals which due to a rather high consumption (17.7 kg/t) constitutes one of the major cost items of the plant (i.e., 58% of total reagents cost). A detailed laboratory scale study showed that replacing air with nitrogen could reduce the consumption of sodium sulphide (i.e., H2S or mineral origin). Nitrogen for the plant was supplied from an oxygen plant used for the smelter through a 1400 m long pipeline. The existence of the oxygen plant at the Sarcheshmeh complex was a key factor in the implementation and success of this project. After using nitrogen in the plant for a period of twenty one months, the consumption of sodium sulphide was reduced from 17.7 to 14.2 kg/t at constant metallurgy. The reduction was lower than expected which was mainly due to the type of sodium sulphide used and the lack of any automatic instrument to control the depressant (sodium sulphide) dosage. The latter in turn caused the operators to overuse sodium sulphide in order to reach and maintain the target metallurgy (i.e., higher molybdenite recovery along with lower copper content of the concentrate).

Jan 1, 2005

By M. W. Franklin, D. W. Hendriks

"Changing ore types, feed grades and c1rculat1ng loads are some of the many factors that can make flotation feed-back control difficult. To control a flotation circuit using conventional fixed-parameter control algorithms, one must either tune the controllers very often or tune the controllers to the middle of the normal operating range. The former approach is very time consuming, while the latter approach can lead to long periods of either very sluggish responses or highly reactive responses which can lead to instability. The problem becomes compounded if feed-forward variables are introduced, creating even more variables to tune. An alternative to a fixed-parameter control algorithm is an adaptive control algorithm. An adaptive control algorithm continuously retunes itself based on previous reactions to its changes. Feed-forward control also becomes much more viable because the algorithm will tune the feed-forward parameters and the feed-back parameters simultaneously. Using the combination of feed-forward and feed-back tuning is an effective way to decouple the loops needed in flotation circuits where one circuit feeds into another. The advantages of adaptive controllers over conventional controllers will be introduced through the use of a simulator. Also discussed will the be the implementation of adaptive controllers at Brunswick Mining and some of the modifications that are available to help solve more difficult control problems.Brunswick Mining is located just outside of Bathurst, New Brunswick. The concentrator processes approximately 10250 tonnes per day of ore that assays at approximately 8.9 %zn, 3.6 %Pb, 0.3 r.cu and I 00 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 34 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb."

Jan 1, 1986

By K. G. Thorne, D. R. Lentz, A. F. Park

"The Main zone of the Clarence Stream gold deposit is hosted by a shear zone adjacent to the Saint George batholith in southwestern New Brunswick. The mineralization history relates to progressive deformation in the shear zone and the intrusion of the Magaguadavic granodiorite.Of three phases of deformation that have affected the area (D1-D3), D1 is not observed in the Clarence Stream shear zone. Two suites of igneous rocks intrude the shear zone: post-D2, pre-D3 gabbro; and granitic dikes, which crosscut the gabbros. Granitic dikes show a diverse range of relationships to D3 features, from pre-syn-D3 mylonitic fabrics in transposed and highly deformed enclaves, to nondeformed and entirely discordant dikes (post-D3).A variety of veins occur within this shear zone. Zoisite-bearing and later, crosscutting epidote-bearing veins are preserved as relics in quartz-mylonites, and predate quartz veins that host gold mineralization. The epidote-bearing veins are associated with pseudotachylitic cataclasite dikes, consistent with transient brittle failure during ductile deformation.Deformation relates to right-lateral strike-slip motion across the shear zone, and subhorizontal and near-vertical stretching lineations imply transpression. A late (late- or post-D3) dip-slip phase of motion is also apparent, and cooling followed a metamorphic peak early in D2-D3 history. Deformation of the shear zone, and more localized transient brittle failure, provided the permeability for fluid movement and vein emplacement. This scenario is similar to the findings of other studies, in which geochemical, tracer isotopic, and age-dating (U/Pb, 40Ar/39Ar) results suggest that the adjacent Magaguadavic granodiorite provided heat and metals. La zone principale (Main zone) du gisement d’or de Clarence Stream est encaissée par une zone de cisaillement qui longe le batholite de Saint George dans le sud-ouest du Nouveau Brunswick. L’historique de la mise en place de la minéralisation accorde un rôle important à la déformation progressive dans la zone de cisaillement et à la mise en place de la granodiorite de Magaguadavic.Des trois phases de déformation à avoir affecté la région (D1-D3), les effets de D1 ne sont pas observés dans la zone de cisaillement de Clarence Stream. Deux suites de roches ignées se sont mises en place dans cette zone de cisaillement : un gabbro post D2, pré-D3 et des dykes granitiques qui recoupent le gabbro. Les dykes granitiques montrent une grande diversité de relations avec les structures D3, allant de précoces à synchrones aux fabriques mylonitiques D3 dans des enclaves transportées et fortement déformées à des dykes complètement discordants et non déformés (post-D3).On note diverses veines dans cette zone de cisaillement. Des veines contenant de la zoisite ainsi que des veines d’épidote sécantes plus tardives, lesquelles sont préservées comme reliquats dans les mylonites à quartz et sont plus vieilles que les veines de quartz contenant la minéralisation aurifère. Les veines d’épidote sont associées à des dykes de catacalasite à texture de pseudotachylite, compatibles avec une rupture cassante épisodique durant la déformation ductile.La déformation résulte d’un mouvement décrochant dextre le long de la zone de cisaillement et les linéations d’étirement subhorizontales et quasi-verticales impliquent de la transpression. Une phase tardive (tardi- ou post-D3) de mouvement selon le pendage est aussi apparente, et le refroidissement succède à un pic métamorphique tôt dans l’histoire D2-D3. La déformation de la zone de cisaillement et la rupture cassante épisodique ont fourni la perméabilité nécessaire au mouvement des fluides et à la mise en place des veines. Ce scénario est similaire à celui proposé par d’autres études, dans lesquelles les résultats de géochimie, de traceurs isotopiques et de géochronologie (U/Pb, 40Ar/39Ar) suggèrent que la granodiorite de Magaguadavic avoisinante a fourni la chaleur et les métaux."

Jan 1, 2008

By Roussos Dimitrakopoulos

Conventional approaches to estimating reserves and optimizing mine planning and production forecasting result in single, often biased forecasts. This is largely due to the non-linear propagation of errors in understanding orebody attributes from a limited finite number of drilling data, throughout the chain of mine planning and mining. A new mine planning paradign is considered herein to include two interacting and potentially fusing elements: stochastic simulation and stochastic optimization. These two elements provide an expanded mathematical framework that allows the modelling of orebody uncertainty and its direct integration to mine design, production planning and valuation of mining projects and operations. This stochastic framework has shown to increase the value of production schedules in the order of 25%. In addition, case studies show that stochastic optimal pit limits are about 15% larger in terms of total tonnage, compared to the conventional (deterministic) optimal pit limits. This difference extends life of mine and adds approximately 10% of net present value (NPV) to the NPV reported above from stochastic production scheduling within the conventionally optimal pit limits. Furthermore, results suggest a potential new contribution to the sustainable utilization of natural resources.

Oct 1, 2009

By K. B. Hodgins, P. Ouellette

"The North American mining industry faces challenging emissions regulations in the coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable.Westport Innovations Inc., Vancouver,British Columbia, has developed high-pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications while reducing emissions of nitrous oxides (NOx), particulate matter (PM), and CO2 with no loss in performance. This is accomplished through late-cycle, high-pressure direct injection of natural gas into a diesel engine combustion chamber at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the natural gas fuel main injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, lowspeed torque, high-power output, no engine knock, and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to the reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored with less impact on weight and space than compressed natural gas (CNG) by virtue of its increased energy density over CNG.Westport has applied HPDI technology to the Cummins QSK series engines for high horsepower applications such as power generation and mine haul trucking. HPDI can also be applied to other engine manufacturer platforms and market applications. Westport is interested in demonstrating the unique characteristics of HPDI in mine haul trucks to show diesel performance with low emissions levels using low-cost LNG fuel.Retrofitting a Tier 1 engine with HPDI would provide emissions reductions below the EPA 2006 Tier 2 standards while maintaining the performance and efficiency of the Tier 1 platform. The longer-term target is the Blue Sky voluntary standards of 3.8 g/kW-hr (2.8 g/bhphr) of NOx + non-methane hydrocarbons (NMHC), and 0.12 g/kW-hr (0.09 g/bhp-hr) of particulate matter (PM) and future standards. Typically, an HPDI engine is capable of reducing NOx emissions by 40% over diesel operation at the same efficiency. On a mining truck meeting Tier 2 standards, this NOx reduction would translate into NOx emissions approximately 14 t per year lower than under diesel operation. PM emissions are typically reduced by some 60% with HPDI fueling, which would translate into a yearly reduction of 650 kg. Similarly, engine-out greenhouse gas (GHG) emissions are reduced by 21%, resulting in a yearly reduction of approximately 950 t per vehicle.Above those of emissions reduction, efficient natural gas usage in mine haul operations would offer significant benefits in terms of fuel cost savings, which may be further combined with monetary emission credits. HPDI technology would enable operators to exercise environmental stewardship while gaining a competitive advantage in advance of new Tier 2 and Tier 3 emissions regulations. The advantages of natural gas use among mine haul truck operations can be replicated across a broad range of engines and applications."

Jan 1, 2005

By C. O. Aksoy, H. Kose, K. Heasley, E. Yalçin

"In Turkey, the growing demand for lignite has resulted in increased lignite production and an emphasis on improving underground recovery. This has resulted in a gradual increase in the application of the retreat longwall mining method and also in the extraction of the safety pillars protecting permanent underground structures (drifts, shafts) in mines prior to their abandonment.Extracting these safety pillars presents a special hazard to mine employees and the stability of the mine. Often subjected to high stresses, the behaviour of these pillars is not always predictable. Special care must be taken to ensure that infrastructure does not collapse prematurely, and that working conditions remain safe. Otherwise the extraction must be halted, and the remaining coal lost.This investigation reports on a study of the stability of safety pillars during the final extraction phase of the Hustas mine in Soma, Turkey.” The model construction was based on mine plans, and material properties were derived from physical properties testing. Observed subsidence effects from other mining events were used to calibrate the overburden lamination thickness.The model results compared well with surface physical disturbance occurring as a result of mining, as well as with conventional longwall stress redistribution theory and underground observations. The study has shown that properly calibrated models can be useful in assessing mine safety during remnant pillar extraction. The LAMODEL results demonstrate the convenience of this easy to use software."

Jan 1, 2004

By Hugo Julien

According to OSHA 29 CFR Part 1910.119 (Process safety management of highly hazardous chemicals), Canadian Provincial Safety Standard Acts or Federal laws, the owner of stationary equipment (Boilers, stacks, piping, pressure vessel, etc.) should follow a complete inspection plan and follow an Integrity Operating Windows (IOW’s) adapted for each of them. Some important variables shall be included in the inspection plan such as specific damage mechanisms versus alloy used in the original design, process conditions, etc. Some North American’s standards exist, like the one listed in ASME PTB-2-2009, to help owner to create such inspection program. The new API RP 584, Integrity Operating Windows (IOW’s) can guide Mining & Metals owners to find out their specific IOW’s. Inspection frequencies are often described in the Jurisdiction Safety Acts such as the British Columbia B.C. Reg. 104/2004, etc. but often left in the owner representative responsibility (Bill C-21, federal Act to amend the Canadian Human Rights Act). Every deficiency should be repaired according to recognized Codes such as ASME PCC-2, etc.. If flaws not conforming to the original Code of construction are found, this article will introduce the Fitness-For- Service assessment principles to be able to accept it without any repairs.

Jan 1, 2014

By Joe Pease

"The demand for minerals and metals is increasing. Head grades of ore bodies are dropping. Remaining ores are becoming finer grained, more complex, and more logistically challenging. Mineral processing – in particular comminution – already consumes a huge amount of energy. But in 20 years’ time, it will require about six times as much energy as today to meet the world’s mineral demand.Unless we do something different.As minerals professionals, it is our job to find that “something different”. The world is relying on us. Of course, we must look for new breakthrough technologies and techniques. We must find them, and we will find them – most likely in surprising areas.But what if we also already know how to make 30-50% improvements to efficiency? Just by using existing technologies, by applying modern analytical techniques, by custom designing our plants, by applying manufacturing principles, by breaking down our management silos between disciplines.The thing is, industry professionals already know this. Yet – in spite of a lot of intelligent people trying very hard – we just can’t seem to make it happen.This discussion considers why, despite our best efforts, we don’t get the best out of what we already have. Why we are wasting energy and money. Once we understand why, we can set about unlocking that value and improving industry productivity and energy efficiency. We will discuss the role that professionals and volunteer professional organisations like CMP and CEEC can play in catalysing the changes."

Jan 1, 2015

By C. V. Umipig, G. G. Hutalle, E. E. Israel

TVI Resource Development (Phils) Inc. Canatuan mine is a polymetallic ore deposit located in the Province of Zamboanga del Norte on the island of Mindanao in the Philippines. The deposit consisted of an oxidized capping of gossan overlying a Besshi type volcanogenic massive sulphide lens which is near surface and flat lying. Construction and development of a sulphide processing plant began in early 2007 and commissioned in November 2008. During the initial stages of sulphide operation, high copper (Cu)-low zinc (Zn) ore was fed to the plant. Marketable copper concentrate at 91-95% recovery was produced utilizing a high-pH bulk sulphide rougher flotation and 2 cleaning stages. Because of increased levels of Zn of the ore body, a Cu/Zn separation circuit was initiated in early 2010 following an intensive laboratory test work program. This Cu/Zn separation circuit was necessitated because of the copper ion pre-activation of the sphalerite that lead to the zinc being readily recovered to the copper rougher concentrate. In-situ activation of zinc (in the pit and stockpiles) was caused by the leaching of secondary copper minerals in the ore (particularly from the dominant copper species, chalcocite and covellite). This problem required the development of metallurgically complex and intensive reagent regime to effectively depress the activated sphalerite. As well, the immediate reactivation of zinc after it has been depressed, at the onset of Cu/Zn separation flotation, added additional metallurgical complexity to the process. Subsequent to the Cu/Zn separation circuit, an unconventional, yet proven effective, simultaneous cyanide detoxification-zinc flotation circuit was set-up to recover the zinc. Laboratory test work results realized Cu-Zn recovery differential from a Cu/Zn separation circuit of over 40-45%. This performance has been achieved in the plant, at 72% Cu overall recovery. With the gradual improvements on-going with zinc circuit capacity and effective zinc separation being achieved, zinc recovery has currently reached 40%.

Jan 1, 2012

By Julián M. Ortiz

Uncertainty quantification of a spatially distributed variable at any scale can be handled through geostatistical simulation. Large computation time, storage, and post-processing of the realizations are required to obtain a final assessment of block uncertainty. Multi-Gaussian kriging is a flexible alternative to simulation. The idea is to compute the conditional distribution of uncertainty after normal score transformation of the original samples. Under the multi-Gaussian assumption, all marginal and conditional distributions are Gaussian, hence fully defined by their mean and variance. The parameters of the conditional distributions are obtained by simple kriging and can be back-transformed to the original units of the variable of interest. An estimate and any summary of uncertainty can be easily retrieved. The main disadvantage of performing multi-Gaussian kriging is that change of support is not straightforward, that is, calculating uncertainty of block grades. We propose a methodology to overcome this limitation by considering a matrix simulation to generate multiple probability fields. Each probability field is used to draw spatially correlated point values from the point-support conditional distributions, and multiple realizations of the average can be obtained. This permits the calculation of the average over the block and its uncertainty. These blocks may correspond to selective mining units or to volumes from longer production periods relevant for engineering decisions. They can even be disjoint blocks, such as when several faces are mined at the same time. POSTMG, a Fortran program to perform these calculations, is described and a case study is provided.

May 1, 2004

By R. J. Johnston

"INTRODUCTIONPoint Mines is located about 65 miles east of Hay River on the South Shore of the Great Slave Lake. It is connected to the Northern Alberta Railway System by the Great Slave Lake Division of CN Railways at Roma Junction, Alberta.The operation started in the fall of 1965 with a capacity of 5000 t.p.d. An addition was put into operation late in 1968 to bring the capacity up to 8000 t.p.d. The present milling rate is 11,000 t.p.d.The location of Pine Point Mines is such that long end cold winters are to be expected end temperatures of lower than -200F are encountered from late October to late March, with extended periods of -300F being common in January and February.It was recognized by Cominco engineers during the initial design period that since freezing would be encountered with open pit ore somewhere in the crushing circuit, the problem was to reduce it as much as possible. Other mines, working under similar conditions, found that the fine ore bins feeding the grinding circuit were the main problem area. The decision was reached, therefore, to have heated fine ore bins and to make sure thst the ore was sufficiently warm to prevent freezing.CRUSHING PLANT FLOWSHEETThe crushing plant has a standard open flow circuit (flowsheet). Ore from the stockpile is loaded into R-50 Euclid trucks by Caterpillar 992 Front End Loader with 11 cu. yd. bucket and dumped into a 42 x 65 C.A.C. Superior Crusher driven by a 300 HP motor. The crusher is set at a nominal 5 inches. The ore falls through into a 100-ton surge bin. There are high level and low level nuclear gauges to allow the primary operator to optimize for optimum orientation."

Jan 1, 1972

By Gerald Whittle

What is Enterprise Optimization? Releasing value through better planning decisions: Philosophy, Methodology, Software The key to 5% -35% increase in enterprise value (NPV) The culmination of 25 years development in optimization for the mining industry ?Jeff Whittle Simultaneously optimizing: ?all steps in the value chain ?all assets in the enterprise portfolio ?all periods together

May 1, 2010