Search Documents

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By Q. Zhang

The necessary capability of the gravity transportation pipeline system for cemented coal gangue backfilling at the Suncun Coal Mine, China, is about 74.4 m3?h-1 according to mining production and working times in the mine. It is estimated that the working velocity and maximum pipe length-backfill depth ratio of the backfill system are 3.82m?s-1 and 5.4, respectively and that the probable backfill capability of the system is 110.18m3?h-1. Results of hydraulic calculations for the backfill transportation system show that the designed backfill system is reliable in flowability and sufficient for backfill capability needs.

May 1, 2007

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level position is then calculated from these pressure readings using an equation which includes the bulk density in the froth and bubbling zones. The precision with which the level is detected depends on how well these density values represent both zones. The calculation of these bulk densities from theoretical considerations is not possible and, therefore, the practice is to estimate them by calibration. Unfortunately, the calibration parameters often do not report the level with an acceptable accuracy. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the bubbling and froth zones. This probe can be used to detect the position of the interface to an accuracy of± 5 cm. The probe can be used while the column is in operation, which allows the on-line calibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 min diameter) are described.

Jan 1, 1989

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By Judy K. Todd

Double benching has been utilized as an excavation technique in open pit mines for many years. This process involves drilling, blasting, and excavating the material for the design bench height. A second bench is then excavated without the creation of a catch bench, i.e. only minimal offset from the first bench face is allowed when drilling off the second bench. The result is a double high bench face or double bench. When drilling off the second bench, the offset of the drill from the bench face projects the lower bench face into the pit up to an extra five meters. This reduces the maximum attainable bench angle, enhances the probability of rock escaping the catch bench and increases the overall strip ratio. The generally utilized process of trim blasting also can impact on the final bench profile by contributing to blast damage of the face. BHP Billiton Diamonds Inc., Ekati Mine Diamond MineTM, has pioneered the usage of a technique that eliminates this offset. Double benching is accomplished by drilling a single, 30m pre-shear (two 15m benches) to define and protect the final bench profile. This article provides a comparison of the attained face angles obtained in the field utilizing both of the above methods, as well as a comparison with the analytically predicted angles prior to excavation.

May 1, 2002

By Flavio Rojos-Tapia, Oscar Pereira-Cerda, Samuel Sánchez-Pino, Samuel Sánchez-Baquedano

"Pneumatic flotation was introduced to the Chilean Copper Mining Industry in 1993 by Ingeniería de Minerales S.A. (IDM). The technology is based on the designs of Dr. Rainer Imhof from Germany, who is the designer of several different types of pneumatic flotation cells, already sold through his Company Maelgwyn Mineral Service Limited (MMH). The company is represented by Ingenieria de Minerales S.A. (IDM) in South America.Pneumatic flotation, has been used in tough industrial applications .It has been successfully used for metallic ores such as copper sulphide and oxide minerals, copper slag, silica and silicates from iron magnetic preconcentrate (reverse flotation) and gold. It has also provided promising results when applied to molybdenum flotation. The latest applications, with ultrafine molybdenum particles in operating plants, is showing the V and G Cell (end model designed) as a real technological alternative to conventional flotation., The G Cell is an extremely high speed flotation machine with high selectivity which introduces the possibility of producing a final molybdenum concentrate with only one stage of cleaning. This is a completely new development in molybdenum flotation in the industrial circuit which has the potential to dramatically reduce the circulating load in the cleaning circuit. As a consequence the capital costs of future Molybdenum plants may also be reduced. The suitability of the G Cell will have to be determined on a case by case basis but it provides the metallurgist with an alternate flowsheet for consideration.The good performance of the G Cell can be explained by the high gas hold-up and very effective micro-turbulence which helps improve the attachment of solid particles to the bubbles. This technology may change our traditional concept of residence time in flotation. Additionally, the rotation phenomena introduced in the vessel of the G Cell ,creates radial separation forces which are critical to achieving a more rapid separation of the target minerals from the tailing. This results in a much reduced residence time requirement in the flotation machine. Some benefits associated with the use of the new G Cell are: less energy consumption, less maintenance costs, simple and reliable circuit to operate and a small area required for installing the circuits.As a result of the industrial experience in the Chile, the pneumatic flotation type G Cell can be regarded as a technology which must be considered as a replacement technology for the rougher and cleaner stages for fine particle flotation."

Jan 1, 2008

By T. Grammatikopoulos, A. McKen, O. Christiansen

Vanadium mineralization occurs in oxide-rich horizons within layered metagabbro zones of the Sinarsuk deposit, West Greenland. The main oxide minerals are vanadiferous magnetite and ilmenite, comprising 30% to 90% of the rock volume and the ratio of magnetite to ilmenite ranges from 3:2 to 4:1. Ore microscopy shows that magnetite and ilmenite vary between 0.2 mm and 4.5 mm in grain size, but locally they are coarser grained. Grains are subhedral to euhedral and annealed suggesting that they will liberate very well upon grinding. Electron microprobe analyses indicate that magnetite grains are homogeneous and have a vanadium content, in different mineralized samples, ranging from 1.93 wt% to 2.68 wt% equivalent V2O5. Ilmenite hosts abundant and variably sized hematite lamellae, and it has vanadium contents ranging from 0.32 wt% to 0.59 wt% equivalent V2O5. Preliminary beneficiation of two composite bulk samples shows the samples can be beneficiated fairly easily using low-intensity magnetic separation at a coarse grind (106 microns to 600 microns) to yield a vanadiferous magnetite concentrate. The presence of hematite lamellae in ilmenite prevents recovery of a satisfactory ilmenite concentrate. The most likely beneficiation flowsheet would encompass a primary mill (SAG or rod mill), which would grind to about 600 microns, followed by a rougher magnetic separation stage. The rougher magnetic concentrate would be reground in a ball mill until suitable liberation is achieved. The reground material would then be cleaned in further LIMS stages. However, further laboratory testing is required to establish the final beneficiation program. This work demonstrates the value of mineralogical investigation in guiding and explaining the results of beneficiation processes.

Jan 1, 2002

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By Patrick F. R. Murphy

An ultra-low profile LHD has been developed by EJC Mining Equipment of Burlington, Ontario for narrow-reef mining applications. This paper discusses the challenges encountered during the evolution of the machine's design and subsequent field testing. Continuing research and development focuses on optimizing machine performance and controllability, reducing emissions, and enhancing maintainability. Details will be given on field trial experience and ongoing test work being carried out at the manufacturing facility.

May 1, 2004

By O. K. Mahabadi

The scope of this study is to simulate the behaviour of a layered rock sample under standard laboratory Brazilian Disc test using an innovative combined finite-discrete element method (FEM/DEM) research code. The influence of layering and the direction of loading on the samples behaviour are studied through various layering and loading configurations. A parametric study including the effect of loading rate on the tensile strength of samples has been carried out. This paper demonstrates the suitability of the numerical approach to explicitly model rock deformation and failure.

May 1, 2009

Westwood Quebec Long Life, Low Cost CONSTRUCTION UPDATE ? Shaft advanced to 840m (after 1 year), 3 km of down ramp and 2 km of exploration drift ? Head frame and hoist room structure completed ? 2009, 84,700m drilling program completed (increase 9%) 2010 OUTLOOK ? $102 million expenditures planned ? Shaft to advance to 1,300m and the first loading excavate 71,500m drilling program planned

May 1, 2010

By Richard Mcivor, Largo Albert

"Inco Limited has operated aluminum mine shaft conveyances since 1968. Aluminum conveyances are used where the hoisting in system requires lightweight conveyances to maintain the hoist rope safety factors and mine hoist rope pulls as dictated by government regulations. Inco Ltd. currently has 20 skips (including spares) operating in the Ontario Division mines. The main problems encountered are with galvanic corrosion between dissimilar metals and metal fatigue. This paper will highlight some of the problems encountered and illustrate methods utilized to overcome the problems and improve the conveyances performance.IntroductionAluminum mine shaft conveyances have been in use at Inco Limited's various Sudbury district mines since 1968. All of the conveyances currently in use are skips used for hoisting mine ore and rock. Inco had an aluminum quick change Kimberley-type skip and cage in operation at its Totten Mine in the early 1970s, but this mine is no longer in operation and no further comment will be made.The primary reason why aluminum conveyances are chosen over conventional steel conveyances is because of their light weight. Typically an aluminum conveyance will weigh about 60% to 70% of a steel conveyance of similar design. The lighter weight conveyances will allow higher payloads to be used and still maintain the statutory hoist rope factors of safety. It must be remembered that increasing the payload will increase the power required to raise the load and the hoist will have to have the necessary horsepower for the increased payload or the system will be overloaded.The front dump (Rola-chute) skips are of the bail-less design, i.e. the box structure also supports the load and has the shaft guide shoes attached directly to the side of the box structure. The Copper Cliff North Mine and South Mine skips have a joint in the centre of the conveyance and are installed in the shaft in two sections and connected with pins. This feature allows very long (42 ft) skips to be used in areas where a one-piece bail-type conveyance could not be installed. It is not practical to make sectionalized bail-type conveyances"

Jan 1, 1988

"Drilling twinned holes is a traditional technique used for verification of intersections of high-grade mineralization, testing of historic data, or confirmation of drillhole data during geological due diligence studies. Twinned holes can also be used for special tasks such as correcting earlier data that are recognized to be biased. Successful implementation of the twinned-holes technique requires thorough planning. Experience suggests that good practice is to drill twinned holes no more than 5 m apart. Many unsuccessful twinned-holes programs could possibly have failed because the twinned holes have been drilled too far apart.Twinned holes are best compared by mineralization intersections and, if the data and geological characteristics of the deposit permit, by samples, equal-length composites, or geological units. Variables to be verified by twinned holes should include the thicknesses of the geological units of interest (e.g., mineralized thickness) as well as the presence of significant geological features (e.g., ore/mineralization contacts, alteration, etc.).A formal, rigorous analysis of twinned-hole data is essential. Repeatability of sampling, analytical results, and bias must be analyzed and statistically quantified. The number of twinned holes required for conclusive statistical and geostatistical analysis can be as high as 20-30, in particular where the studied variables are characterized by high short-range (local) variability.The efficiency of this approach is demonstrated by several examples of successfully applied twinned-hole projects, including applications to orogenic gold, mineral sands, bauxite, and iron ore deposits."

Jan 1, 2009

By M. Sharafodin, A. A. Hassanipak

Abstract - The essential aims of additional borehole drilling are to improve the reliability of grade and tonnage estimates in each reserve class and to increase ore tonnages. The "GET" function presented in this paper considers strategies for achieving both of these goals simultaneously, and therefore is advantageous for selecting sites for additional boreholes. The "GET" function is either a linear or a non-linear product of three variables G, E, and T: f(G,E,T,) = G??E??T??where the values of any or all of the exponents ?, ?, and ??may differ from unity at the discretion of the user. G and E are the average estimated block grade and the average estimation error for ore blocks in one vertical column, and T is the compounded ore thickness within the column. To illustrate its utility, the GET function has been used for determination of the most advantageous sites for additional drilling in the Shah-Kuh Pb-Zn deposit in west central Iran.

Jan 1, 2004

By Ed Beswick

Resource Update Drilling Program ? Pre-feasibility ? Exploration Metallurgy Program ? Grindability ? Metallurgical Optimization ? Hydrometallurgical Options Preliminary Mine Development Design Environmental Permitting Infrastructure Development

May 1, 2008

By Norman O. Lotter, Lori Kormos, Greg J. Wilkie, Peter J. Whittaker, Johannes S. Stickling

"Assessment of opportunities to improve mineral processing performance in existing concentrators and in describing undeveloped orebodies is key to improving the business case of a mining company. This assessment has traditionally been performed using the distinct and separate inputs from Mineral Processing and Mineral Science.More recently, Process Mineralogy has been used to integrate these two disciplines. This trend has been driven by the need to develop and process more challenging ore deposits, and has been assisted by the availability of modern automated instruments. Together with the acquisition of a QemSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) from CSIRO in Australia, and with the use of a supporting SEM with EDX / WDX capabilities and an XRD, the development of Process Mineralogy at Falconbridge commenced in 1997.The sampling challenges in presenting a QemSCAN with representative sample material at the polished section level are significant, but have been effectively addressed. The full description of this aspect is beyond the scope of this paper.It is shown that, by use of this approach, the set nature of an orebody can be best exploited with selected flowsheet changes in a concentrator which address the generic characteristics of the orebody. In this way, the flowsheet provides a process that more effectively fits the mineral processing requirements of the ore. This leads to clear and tangible improvements in grade and recovery."

Jan 1, 2002

By Pablo González, Rodolfo Espinosa, Jose-Luis Noyola, Sergio Cossio

"Minera Penmont, at La Herradura, is a joint venture between Industrias Peñoles, S.A. de C.V., and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with two-stage crushing and heap leaching facility, the gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130,000 gold ounces per year, and treatment capacity is 22,000 tonnes/day. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to the coarse visible gold, in some coarser particles ranging from 100 to 600 microns.Sampling and assaying protocols where established during exploration and prior to starting up operations, based on nomographs developed from early heterogeneity tests. But, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block made of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to starting up operations (“existing”) and the new protocol (“leaching”). In the “existing” protocol, subsampling is done through riffle splitters, and coning and quartering. Fire assaying is used to estimate the gold content, on a 50 g sample. In the “leaching” protocol a 12,000 g sample was bottle rolled cyanide leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this “rotary sampling” protocol and for comparison purposes, gold assays were also repeated using the “leaching” protocol.Test results were compared in three groups < 0.30 g/t (below cut-off), 0.30 to 0.8 g/t, and >0.8 g/t. Overall. Results show that the protocol established prior to starting up operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2003

By Richard Phiri, Mike Milupi, Jackson Kapobe, Anton Lemmer, Charles Mazala

Sustainability of plant operations in a rapidly changing mining environment requires a well-trained workforce to ensure smooth running of operations. To ensure availability of trained labor, Mopani Copper Mines PLC set up a training facility in 2013. The school offers training in Engineering, Mining and Process. The engineering section enrolls grade 12 school leavers for artisan training. Mining section offers comprehensive safety induction program to employees and contractors to meet the Mopani zero tolerance accidents safety policy. The process training section offers advanced training programs for plant operating personnel and university graduates. The program includes needs analysis, theoretical metallurgical modules, practical plant training and e-learning modules. The school also offers assaying and sampling courses. All the above courses are extended to individuals and other mining houses outside Mopani wishing to have their personnel trained. The Mopani sustainable development academy ensures that contractors engaged on the Mopani sites are fully registered, comply with all relevant regulations and have undergone induction program before they can be allowed to work on the mine. INTRODUCTION “Sustainable operation of the mining industry requires a continuous supply of trained human resources” (Kapobe et al., 2018). The publication by the Asian Development Bank (2014) argued that there was a mismatch between the demand for high-level skills and the oversupply of low-level skills. Globally, the mining industry requires continued supply of skilled manpower for its complex operations and long term projects whose sustainability is absolutely necessary. Implementation of newer technologies in plant operations to ensure cost effective and efficient operations requires trained and skilled labor at various levels to handle ever-changing challenges. Dutz (2007:152–156) made three recommendations for Building Worker and Management Skills in India: Strengthen enterprise - based training. The government should help ensure that the benefits of in- service training are widely recognized by enterprises, while simultaneously providing strong financial incentives Improve vocational training - Vocational education and training systems have been unsuccessful in preparing graduates to meet market needs, particularly because of a lack of interaction with industry. Public and private vocational education and training providers should be strengthened to make them more responsive to industry demands. Curricula should be updated to reflect modern technologies. Strengthen business, management education, management of research and commercialization - business and management education should be strengthened through public-private partnerships. Innovative management courses should be introduced. Although these recommendations were made for India, they also apply to Zambia and other low and medium income nations.

Jan 1, 2019