Search Documents

By S. Shairp

Copper is an impurity as well as a necessary reagent in the processing of zinc sulfide concentrate at Hudson Bay Mining & Smelting Co., Limited's (HBMS) zinc pressure leach plant. Copper is present in the zinc concentrate as chalcopyrite, which consumes reagents necessary for zinc leaching. A small percentage of copper precipitates in the autoclaves, discharge lines, and flash tanks, requiring maintenance of the equipment and disposal of the solids. Copper also precipitates in the neutralization stages and is removed to low levels in a specific copper removal stage of purification. Yet some copper, as copper sulfate, is required, along with potassium antimony tartrate, in the final purification stage to improve cobalt removal from the zinc sulfate solution prior to electrowinning. The behaviour of copper experienced at HBMS's zinc pressure leach plant is discussed.

Jan 1, 2008

By M. Abdellatif

Successful demonstration of The Mintek Thermal Magnesium Process (MTMP) was achieved in November 2004 at the pilot-scale, About 30 tons of magnesium producing recipe was smelted in the DC arc furnace over a continuous operation of 8-days, Twenty-two furnace batching-tapping operations were carried out at a feed rate of 525kg/h and a smelting temperature of 1600-1700°C, The MgO content in the produced slag was as low as 6,7%, and averaged 9,2% MgO, resulting in an overall magnesium extraction of 77%, which reached 87% during good operating periods, Magnesium vapour was extracted at a rate of 70-85kg/h and was delivered to the condenser that was operated at 680-720°C, The magnesium was captured in the condenser crucible in a liquid state, allowing its prompt tapping, More than 3500kg of crude metal were produced over 15 on-line metal tapping operations, On average, a condensation efficiency of 85% was achieved during the entire testwork, which peaked at 87% during steady operations, The quality of the crude metal was similar to, if not better than, that of the Magnetherm's crude magnesium, A pre-feasibility study has indicated that the MTMP has the potential for lower capital and operating costs as compared to the electrolytic process, and therefore Mintek and its consortium partners are exploring opportunities for a commercial production facility.

Jan 1, 2006

By S. Mostaghel, Fariba Azgomi, Steven Goodman, M. Oliazadeh

"It is known that copper loss to the slag phase can be in the forms of chemical dissolution and mechanical entrainment. The contribution of each mechanism to the total Cu-loss depends on different parameters and may vary significantly. To reduce emissions to the atmosphere and to shorten the converting cycle, most industrial processes are aiming at production of high matte grades. Increased oxygen-to-sulfur potential, required by these processes, results in a highly oxidized slag, which in turn leads to an increased concentration of the chemically dissolved copper in the slag phase. Hence, slag cleaning processes are becoming increasingly important for economic viability of the smelting operations. Hydrometallurgical, pyrometallurgical, and mineral processing routes have been used for copper recovery from slag. The current article reviews a trade-off study evaluating two of the commonly used methods (namely flotation and electric slag cleaning furnace) by comparing the technical pros and cons, operability/maintenance requirements, and capital/operating costs of the operations.INTRODUCTIONLarge volumes of smelter and converter slags are produced by copper smelters around the world. It is estimated that for production of each ton of metal 2.2 tons of slag is produced (Gorai, Jana, & Premchand, 2003). Considering the current pressure on the mining and metals industry for “zero-waste, sustainable and environmentally friendly” extraction of metals, it is absolutely essential for metal producers to improve their efficiencies in order to remain competitive. To meet these objectives, almost all metal producers, from steelmaking plants, ferroalloys, base and precious metals producers, are trying to reduce their metal losses to the slag phase. In particular, copper producers are aiming to produce higher matte grades in their smelting furnaces to reduce the converting time and improve their overall throughput. Copper smelters need to minimize their copper/precious metal losses to the slag phase before final landfilling/use of slag. The current article, therefore, briefly reviews the copper loss to the slag phase, methods of metal recovery from the slag and then presents a trade-off study conducted for a green field flash smelter of the sulfide concentrates. A comparison was made between two of the major process routes for metal recovery from slag, namely slag cleaning furnace and flotation."

Jan 1, 2016

By D D. Deacon

A brief description is given of the requirements which No. 4 Shaft has been designed to meet and of the methods by which two-stage winding of rock has been accommodated in a single shaft sunk to a depth of 7,421 ft. This is followed by a consideration of the factors which led to the decision to sink the shaft as rapidly as possible. Introduction T HE No. 4 Shaft of Hartebeest-fontein Gold Mining Company, Ltd., has been sited to serve the deep southern area of the mine, some 1,500 claims in extent, between the elevations of 6,250 and 7,300 ft. below surface. From this area, some two-thirds of the mine production will ultimately be obtained. Above the 6,-250-ft. elevation, an existing shaft hoisting system, situated adjacent to the reduction plant, is of adequate capacity to cater for all ore hoisted to surface for milling. No. 4 Shaft will therefore be required to provide downcast ventilation of 1,000,000 c.f.m., together with surface hoisting facilities for men, material and development rock and underground hoisting

Jan 1, 1965

By Shichang Liu, Hongli Jia, Zhaolian Wang, Maotang Liu, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce and promote a latest technology and equipment for magnetite. It’s featured of purifying concentrate, lowering tailing grade, high concentrate recovery rate and stable operation. HUATE® New Style Elutriation Electromagnetic Separator is an equipment to obviously upgrade magnetite. The slurry is fed into separation area through feeder. Generated by excitation coil, the working magnetic field distributes specially in separation area. Under the combined effect of the background field, excitation and demagnetic field and gravity, the mineral particles float downwards in the form of magnetic chains, and interact with the rising water. The gangue, non-magnetic particles, lean intergrowth,etc will be discarded as tailing via overflow tank and pipe. While the magnetic will be discharged from concentrate pipe. Its grade is 2%-10% higher than that of traditional magnetic separation equipment. It adopts the technologies of transformer oil cooling, alternative and uniform pulsation magnetic field controlling the tailing grade, larger drum feed-in device, more uniform umbrella scattering discharge and stabler output current, and realizes lower coil temperature raise, stabler magnetic field, more uniform discharge, effective isolation of weak-magnetic area from non-magnetic area, more obvious upgradation and recovery rate and lowering tailing mFe%. It’s more suitable to purify and thicken the high grade and ultrafine iron powder. Compared with traditional elutriation equipment, it adopts new technologies in removing impurities, operation, large-scale, process simplification, water-saving, remote control, etc. It optimizes the comprehensive beneficiation index, expands its application scope, reduces resource wastes and increases economic benefits.INTRODUCTIONMagnetite accounts for a comparatively great proportion in various iron resources. As it’s a kind of strong magnetic mineral, we must adopt the weak magnetic separation equipment in magnetic separation process to realize removing Si and lowering impurities. While it cannot do very well to use the common weak magnetic separation equipment in the final cleaning to remove Si and lower impurities. At present, the plants, adopting single magnetic separation process to realize cleaning and removing Si and lowering impurities, are in the minority. Most magnetite plants adopt the flotation separation process to remove Si, lower impurities and purify the concentrate. Though with stable indexes and high Fe recovery rate, the flotation process is very complicated, high-cost and with lots of environmental pollution. If adopting the weak magnetic separation equipment can realize removing Si, lowering impurities and the final cleaning, the magnetic separation process should be the primary choice."

Jan 1, 2016

By H. Ranjbar

The Darrehzar porphyry Cu deposit is situated in the Urumieh-Dokhtar magmatic suite of Central Iran. The REE and trace element data suggest that the deposit lies within a continental margin setting. Phyllic and propylitic alteration are pervasive in the area but potassic and argillicalteration are not readily recognized on the surface. This is possibly the result of super gene weathering of the surface rocks or because of an intense phyllic overprint. Poor soil development and abundant outcrop make the area suitable for a case study of lithogeochemical exploration technique for Cu deposits. A total of 262 rock samples was collected over the area and analyzed for 15 elements. The geochemical data cor-relate with the mineralogical composition of the rocks with the phyllic zone being marked by high-er concentrations of Si, Al, K, and by a high sericitization index while Ca, Mg, Sr, total Fe and Mn are more abundant in the propylitic zone. The lithogeochemical study indicates a metal zonation from a Cu + Mo-rich core to a Zn + Pb ± Ag-rich outer zone. Principal component analysis is useful for separating element associations, which in turn reflect the alteration halos. Principal components 1 and 2 depict alteration zoning, where-as 3 shows an association of Cu and Mo, that roughly defines the mineralized area.

Jan 1, 1997

By A. H. Anderson

THE travelling grate coking process was developed by Shawinigan Chemicals, Limited, at their Shawinigan Falls plant. The first production unit went into operation a month prior to the outbreak of the war. Since then a substantial part of the coke used in the manufacture of calcium carbide has been produced by this process. In the following will be given a short account of the development work, a description of the process and the equipment, a discussion of the properties of the coke, the economics of the process and its future possibilities. EXPERIMENTAL WORK The carbide industry is a large consumer of coke, one ton of commercial carbide requiring for its production 1,200 lb. This coke must meet certain specifications in order to be acceptable. It should have a low ash content, preferably below 8 per cent, and the sulphur and phosphorus content must not be above specified limits. The size of the coke is also important. If it is too large it has to be crushed before it can be used in the furnaces, and if it is too fine it may have to be screened and briquetted. In addition, it must be dry. Although it was generally possible to purchase coke, including petroleum coke, and coke fines, in the quantities required, it became increasingly more difficult as time went on to obtain coke of a suitable quality at an attractive price. It was therefore natural for us to look to coal carbonization as a means of basing the supply of the fundamental raw material for carbide manufacture on something more solid than the shifting conditions of the coke market.

Jan 1, 1944

By David K. Fountain

"The growth of the mining industry in British Columbia in the last ten years has been largely the result of the development of large low-grade copper and molybdenum deposits. There are two problems which must be solved in the search for mineral deposits of this type. It is necessary to detect large volumes of rock containing a low percentage of total sulphide mineralization1 and, secondly, to get some idea of the economic significance of this mineralization. The standard geophysical exploration techniques available have a varying degree of application in the search for disseminated sulphide de-posits. The electrical methods, and the induced polarization method in particular, are the most successful direct methods, and magnetic methods have indirect application in most situations. This is illustrated by geo-physical survey results from several properties in British Columbia."

Jan 1, 1968

By P. M. May, V. Gella

The deportment and speciation of trace elements during mining and minerals processing is becoming an area of increasing concern with regards to potential health and environment risks. The use of chemical modelling can enhance our basic understanding of the deportment and speciation of trace metals under conditions present in gold processing solutions, and assist in laboratory and field investigations. In this paper, we report the results of chemical speciation modelling using the JESS software package for the trace toxic elements Pb, Cd, Hg, Se and Te in cyanidation solutions of varying salinity and relate the models to experimental data. The speciation of mercury is examined in detail.

Jan 1, 2011

By Wayne N. McKee, Scott A. Lewis

"Introduction to the Syncrude OperationSyncrude Canada Ltd., located 42 km north of the city of Fort McMurray, Alberta, (Fig. I) is an integrated operation that has produced synthetic crude oil from the Athabasca oil sand deposit since 1978.The operation, consisting of a surface mine, an extraction plant, a bitumen upgrader, and a utilities plant, is currently capable of producing over 60 million barrels of crude oil per year. Production is expected to increase to 70 million barrels of crude oil per year over the next five-year period with no major changes to equipment or process planned.The Syncrude surface mine, producing a total of 675 000 tonnes of ore and waste per day, rates as one of the largest mines in the world. A strip mining method is utilized, with two or three operating benches necessary to excavate a total depth varying between 60 m and 70 m. The 20 m to 30 m of overburden is removed by electric and hydraulic shovels and 200-ton haul trucks, and dumped in the mined-out pit for final storage. The overburden operation creates a flat bench near the top of the ore zone on which the four 60 m3 draglines operate. The draglines excavate interbanded ore and waste in the highwall, with ore placed on the operating bench in windrows, and waste returned to the mined-out pit. The windrowed ore is reclaimed by four bucketwheel reclaimers, and discharged onto a conveyor system for transfer to the extraction plant."

Jan 1, 1993

By P. Rocque, S. Talebi

Although the measurement of blast vibration close to the blasthole is critical to the understanding of rock fragmentation mechanisms and blast damage in the rock masses, limited experience for such monitoring exists. Because much higher vibration amplitude and frequency ranges are expected in rock masses close to an explosive charge as compared to far field vibrations, different problems from those for the far field monitoring must be considered for near field blast vibration monitoring. Currently, guidelines for design of the near field blast monitoring systems do not exist. This paper describes the development of an integrated technique for vibration monitoring close to a blast hole, including selection and installation of transducers, design of a monitoring system and signal recording. A densified cement was designed for grouting accelerometers in order to match p-wave impedance between the rock and grout. The monitoring technique described has proven suitable for blast vibration monitoring within 2 m to 15 m of a blast hole having loading conditions similar to production blasts.

Jan 1, 1993

By Stephen G. Hardcastle, Michel G. Grenier

"Safety and health issues are and have been in the last decade a very high priority item with all parties involved in the Canadian mining industry. As a result of this high level of concern for workers' safety and health, Canadian mines are at the leading edge of environmental control technology. For the most part, the occurrence of pollutants in mines is unavoidable. Dust from mining operations, airborne radiation, gases and heat from the strata as well as gases and particulate from diesel engine emissions will undoubtedly be found to some level in most Canadian mines. A lot of work remains to be done, however, in order to bring all Canadian mines at the same level of proficiency when it comes to safety and health. Also, more work is needed in order to maintain our status as world leaders in this field.CANMET's Mining Research Laboratories (MRL) in Elliot Lake and Bells Corners, Ontario, with the cooperation of the mining industry, have contributed to improving environmental conditions in underground and surface mining and milling operations. The extent of collaboration and efforts vary widely from long-term, multi-million dollar projects between several interested parties to smaller projects involving one laboratory and a single mining operation. This paper gives examples of such collaborative efforts and potential future directions as they apply to: mine ventilation analysis using tracer gas techniques, optimization of mine ventilation network efficiency using real-time monitoring and controlled recirculation (heat saving), respirable dust and radiation sampling and control techniques, diesel emission control using regenerative ceramic filters and, finally, the control of sulphide dust explosions and resulting sulphur dioxide production."

Jan 1, 1990

By J. Ramirez-Castro, J. A. Finch

"Galena is the finest component of the product of a closed-circuit grind treating a lead-zinc ore, largely due to preferential recycling of this high-density mineral by the cyclone. For example, at the Pine Point Mines concentrator, for ~ 55% -200 mesh over-all, the galena will be close to 95% -200 mesh. This sliming of the lead can limit recovery, selectivity and dewatering. A proposed circuit modification to reduce the sliming is to incorporate a unit cell. A simulator was constructed to study the No. 3 grinding circuit at Pine Point modified by a unit cell on ball mill discharge (BMD).The simulator used a cumulative size basis rate-of-breakage with plug flow ball mill model, the parameters being obtained by laboratory grinding tests. Flotation and the cyclone models used a cumulative recovery/size matrix. The behaviour of each mineral, galena, sphalerite, pyrite and calcite/dolomite, was simulated. Simulation was adapted to a programmable calculator. A close fit to the existing circuit performance at two tonnages and mineral mixes was established.The simulator showed that the modified circuit could significantly coarsen the Pb grind, from 95% to —50% -200 mesh, depending on recovery, without substantially altering the size of the other minerals. The other principal findings were: compared to laboratory flotation tests on existing circuit BMD, the unit cell concentrate (CONC) will be coarser and markedly lower in grade; relatively low unit cell stage recoveries are desirable, because the cyclone scavenges the tail to give a circuit recovery which is higher than the unit cell stage recovery; unit cell stage recovery should not exceed the cyclone stage recovery, as the latter is the maximum circuit recovery; low unit cell stage recovery helps offset the disadvantage of the high flow at BMD; other high-density minerals will also be scavenged into the CONC, as illustrated by pyrite, making CONC quality difficult to maintain; density control of BMD flotation does not greatly alter feed density to the cyclone or ball mill.Possible plant metallurgy is forecast for a CONC diverted to final lead concentrate."

Jan 1, 1980

By P. A. Geusebroek, N. A. Duke

Abstract - The Lupin mine, located in the central Slave province just east of the western boundary of Nunavut Territory, is a world-class example of a Neoarchean-aged banded iron formation (BIF)-hosted lode-gold deposit. At the minesite the gold-mineralized Lupin BIF, separating stratigraphically underlying psammitic wacke and overlying argillaceous turbidite sequences, delineates the Lupin dome, a hammerhead-shaped F2/F3 interference fold structure occurring at the greenschist to amphibolite facies metamorphic transition within the thermal aureole of the Contwoyto batholith. Detailed paragenetic relationships indicate that peak thermal metamorphism coincided with the switch from regional D2 compression to rapid D3 unroofing of the Neoarchean orogenic infrastructure. Gold initially precipitated with pyrrhotite, replacing amphibolitic BIF at the apex of the Lupin deformation zone, separating the east and west lobes of the Contwoyto batholith. Over the course of associated prograde/retrograde metasomatic overprints, gold was further remobilized during garnet and loellingite/arsenopyrite growth in chlorite-altered selvages of late-forming ladder quartz veins. A metamorphic model of ore genesis, with gold being scavenged and transported by metamorphic fluid that was shed and structurally trapped at the amphibolite recrystallization front, is favored over the previously proposed syngenetic and exogenic models of gold concentration that have tended to polarize genetic interpretations to date.

Jan 1, 2004

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By J. A. Russell

AS THE LOCAL electric generating plants increased in size and capacity and costs of producing electricity came down, it became apparent that it was no longer good economy to operate individual boiler plants at the Company's various collieries to power steam hoists and compressors. Great economies could be made by burning the Coal at central power plants and using electric power at the collieries. During the period after the end of the war, a steady and continuing programme of replacing first the smaller steam-driven units, and later the steam-driven compressors, was undertaken, and finally the larger hoists, those at No. 12 Colliery in New Waterford and No. 20 Colliery in Glace Bay, were the last units operated by steam.

Jan 1, 1958

By N. Samman, S. N. Lau

"A series of new, grease-based, solvent free open gear lubricants were developed to meet the demanding service requirements of mining equipment. The use of these products has resulted in better performance under conditions of temperature extremes and in terms of longer component lives. They have gained widespread acceptance within the mining communities for such applications as the lubrication of mining shovels, draglines and ball mills.These products are WHMIS non-controlled and are environmentally acceptable. The benefits and advantages of using this type of product to lubricate mining equipment as well as the field evaluation and experience will be discussed."

Jan 1, 2002

By T S. Cochrane

This paper is based on observations made during a recent visit by the writer to three of the dust research laboratories .in West Germany, each .of which is mainly concerned with studymg the composition and character of the respirable dust produced in mines or at industrial sites. The three institutes are discussed as regards their orgamzat10n and duties, their methods of dust sampling and analysis, and recent trends in research and development. An extensive bibliography completes the paper. Introduction A RECENT trip to Europe to attend international conferences m Austria and m Belgium gave the writer the opportunity to visit a number of research laboratories and mines in Western Europe. The visits to the dust research laboratories in West Germany are the basis of this report. In Germany, cooperative associations formed prior to and since the turn of the 20th Century to promote the safety and welfare of their workers have recognized the effects of airborne dust on the general health of the labour force.

Jan 1, 1964

By C. P. Moore, G. W. Taylor

Vertically dipping lenses of nickel-copper ore at Dumbarton Mines Limited are being mined by a modified blasthole stoping method. The principal access to the mine is provided by a 15-degree decline, which, in conjunction with the use of ramps and declines for secondary access, maximizes the accessibility and mobility of trackless mining equipment. Sublevels are driven in ore on 80-foot vertical intervals and subsequently the ore, ranging in thickness from 15 to 30 feet, is slashed to its limits by a procedure of face sampling and test holing. Two longhole drill jumbos are used to drill off 40-foot vertical slices above and below these levels. Following blasting, the ore falls by gravity to the 500-foot horizon, where it is removed from drawpoints by load-haul-dump units and transported by truck to the main orepass. The rock is crushed to minus 3-4 inches and conveyed to surface by a 30-inch-wide wire rope suspended conveyor. This is achieved in two flights, a lower one of 290 feet and a main flight of 2260 feet. All aspects of the mining operation are discussed in the paper, including ventilation, services and safety.

Jan 1, 1973

By W. S. Dyer

The lignite deposit at Onakawana on the Abitibi river is of particular interest at the present time, since the Ontario Government has recently decided to proceed with the extension of the Temiskaming and Northern Ontario railway to James bay. Forty-five miles of steel will be laid this year to the crossing of the Moose river. This will cross the lignite field. It has been known for many years that lignite occurred in the Moose River basin, but it was not until drilling was commenced at Blacksmith rapids (or Onakawana, as the camp is now known) in June, 1929, that a seam of economic thickness and extent was found. Early in 1929 the Ontario Legislature voted $25,000 for the carrying out of a drilling programme in the Moose River basin. This came as a culmination of two summers' exploratory work by the Geological Branch of the Ontario Department of Mines, and as the result of a report which said; in effect, that further information concerning the mineral resources of the basin could only be obtained by drilling, and that such a drilling programme was well worth while in order to establish once for all whether lignite, fire-clay, or oil or gas did or did not exist in economic quantities in the region.

Jan 1, 1930