Search Documents

By S. Kursunoglu

The aim of this study was to investigate the effectiveness of Ascorbic (C6H8O6) Acid (AA), Activated Carbon (AC) and Guar Meal (C6H12O6) (GM) as a reductant for the simultaneous complete dissolution of zinc (Zn) and manganese (Mn) from a spent and mixed Zinc-Carbon (Zn-C) and alkaline battery powders in sulphuric acid (H2SO4) leaching. AA was tested previously as a reductant by other researchers while AC and GM were tested as a reductant for the first time in battery recycling. The effects of H2SO4 concentration, AA/AC/GM dosages, reaction temperature and leaching time on the Zn and Mn dissolutions were investigated according to 2k full factorial experimental design and Central Composite Design (CCD) technique; then, a simple optimization study was carried out for comparing the reductants. The optimum reductive acid leaching conditions for AA were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M H2SO4 concentration, 13 g/L AA dosage, 1/20 g/mL solid/liquid (S/L) ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. The best reductive acid leaching conditions for AC were determined at 3h leaching time, 80oC leaching temperature, 1M H2SO4 concentration, 3 g/L AC dosage and 400 rpm mixing speed. Under above conditions, Zn and Mn dissolutions were not complete. At 2M H2SO4 concentration, 10 g GM dosage, 700C leaching temperature, 200 rpm stirring speed, 1/20 g/mL solid/liquid (S/L) ratio and 3 hours leaching time, full dissolution of both Zn and Mn was achieved. As a result, three different reductants were evaluated in this study for complete simultaneous Zn and Mn dissolutions. This paper also compared present test results with previous spent battery recycling studies for Zn and Mn dissolutions. Full valuable metals dissolutions from spent batteries were achieved at low H2SO4 concentrations with AA and high concentrations with GM. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leach solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover both Zn and Mn.

Aug 1, 2013

By K. Thuro, S. Schneider, H. Kasling, P. Ellecosta

"One of the most important methods for material testing is the characterization of the hardness, which is defined as the resistance of a material to the penetration of another one. The methods according to Brinell, Vickers, Rockwell and Knoop are today the most common and standardized tests for metal. As they are developed for predominantly ductile materials like steel, they can’t easily be applied to rocks which react much more brittle under indentation. But just as steel, rock is composed of different minerals and has a specific microstructure. Its mechanical parameters are connected with the particular grains, their cohesion and interlocking, just like steel.The abrasivity of rocks and the accompanied wear of drilling tools today are mainly determined by simple and fast laboratory tests such as the Cerchar abrasivity test or the rubber wheel test. Such laboratory tests are good tribological tests, but there are limits. The Cerchar abrasivity test for example has weaknesses in extreme cases, that mean soft or very hard rock types. This leads to an underestimation of abrasivity, e.g. in poorly lithified sandstones or very hard, fine grained and extremely abrasive rocks. As mentioned, hardness characterizes, depending on the type of deformation, predominantly plastic (metal) or elastic properties (rubber). Rocks are in the range between these two extremes. Since the rock drilling process can be seen as a kind of penetration process on macroscopic and microscopic scales, we picked up the idea to characterize the interaction of rock materials and TBM-disc-cutters with hardness tests. In addition, this supports for a better understanding of the wear process on disc cutters. We used the hardnessdisparity concept after Cardu & Giraudi (2012) because wear can be understood as the interaction between the wear part and the material which causes the wear (tribological system). Several rock-forming minerals and some fine to coarse-grained monomineralic and polymineralic rocks were tested. In contrast to Cardu & Giraudi, we used in the first step of investigations the method after Vickers with loads up to 294.2 N (HV 30), depending on the estimated hardness to get bigger indentations and therefore as well information about the cohesion and interlocking of the minerals/grains. We also tested several associated disc cutters. First results show that with higher loads (HV 5 - 30) and at least 15 indentations, we get a structural hardness in fine-grained rock samples, which allows a good characterization of the elasticity and brittleness. Nevertheless, for the coarse-grained rock samples we need up to 40 indentations for a good characterization. Using this method, a prediction of disc cutter wear is feasible taking into account the hardness of the disc cutter steel. In this paper, we would like to present this approved method in material sciences to derive an additional parameter for the characterization of rock abrasivity and wear."

Jan 1, 2015

By W. K. Muwais, R. G. Cuddy

"The Lower Cretaceous McMurray Formation contains the bitumen reserves of the Syncrude Mine in northeastern Alberta. This formation comprises sediments deposited sequentially in fluvial, estuarine and marine depositional environments. The Syncrude Base Mine area consists mostly of estuarine sediments, as much of the original marine sediments have been eroded away. These estuarine deposits consist of channel-fill sediments and interchannel tidal flat sediments with the channel-fills comprising most of the orebody.Channel-fills contain, among other lithologies, interbedded sand, silt and clay rich layers that often occur as sequences of inclined beds with dips up to 25 degrees or more. A detailed knowledge of the distribution of these inclined beds, their lithological characteristics and their continuity is very important in assessing the risk of mine highwall instability . Techniques used to identify and characterize adverse structures are reviewed. INTRODUCTIONGeneralThe Syncrude Canada Ltd. oil sand mine is located within the surface mineable portion of the Athabasca Oil Sands area about 40 kilometres north of Fort McMurray in northeastern Alberta, Canada (Fig. I). The company commenced large-scale strip mining of oil sands in June 1977in the area, referred to as the Base Mine, situated in the southeast corner of the company's two lease areas (Fig. 2).The mining method (Fig. 3) utilizes large electric drag lines operating on a single bench with highwall depths up to 60 metres. Feed grade oil sand (= 6 wt.% bitumen) is mined by draglines and windrowed parallel to the highwall crest. Lower grade oil sand « 6 wt. 0J0 bitumen) occurring as waste bands is selectively mined by the draglines and cast back into the mined out pit or placed on the bench and hauled by truck. The windrowed feed is delivered to the extraction plant by a bucket wheel reclaimer and conveyor system. Stripping of Recent, Pleistocene and Cretaceous overburden units is done outside the conveyor systems by mobile equipment. The 4.5 kilometre long mine is split into four quadrants for planning and scheduling purposes, with each quadrant having an individual dragline-bucketwheel-conveyor system.Surface mining of oil sand at Syncrude requires the removal of vast quantites of material. The design of the open pit mine relies heavily on knowledge of the distribution of ore and waste materials, and on the physical characteristics of these materials.The geology of the oil sand below the dragline bench at the Syncrude Mine is complex. Geological, geotechnical and hydrogeological factors play an important role in the design and operation of the mine. This paper describes aspects of the geology that impact on the design and operation of the mine. Some of the methods and procedures adopted by Syncrude to successfully overcome difficulties that the complex geology creates are discussed."

Jan 1, 1989

By Lang Tao, Jun Wang, Wei Xiao, Wenqing Qin, Pan Cao, Guanzhou Qiu, Key Lab of Biohydrometallurgy of Ministry of Education, Central South University

"The effect of metal cations on the rutile flotation using styryl phosphoric acid (SPA) as the collector was investigated by micro-flotation test, bench scale flotation test, zeta-potential measurements and adsorption measurements. The micro-flotation results indicated that Fe (?) and Al (?) ions in low concentrations had obvious activation on the rutile flotation, and Pb (?) ions in low concentrations had smaller activation of rutile, but Fe (?), Al (?), Pb (?), Ca (?) and Mg (?) have strong inhibition of rutile flotation in high concentrations. The bench scale flotation results indicated ethylene diamine tetraacetic acid (EDTA), boracic acid, and sodium hexametaphospate can decrease the metal ions concentrations, and increase the recovery of rutile flotation. Adsorption measurements and zeta-potential measurements revealed that Fe (?), Al (?) and Pb (?) ions were adsorbed on the rutile surface, and had interaction with SPA. But when these ions concentration were over the largest adsorption capacity, residual metal ions could occur chemical reaction with SPA.INTRODUCTIONRutile is one of the favored minerals for production of titanium dioxide white pigment, primarily through the chloride manufacturing process (Stanaway 1994; Hou et al., 2013) However, the majority of rutile ores belong to refractory ores, while flotation is one of the most efficient methods to separate fine rutile from gangue (Dolbear et al., 1937). With the flotation development, many effective collectors were successfully applied in the oxide ore. Many reviews have indicated that organic phosphonic acid collectors showed good selectivity on oxide ores such as ilmenite and rutile (Bulatovic & Wyslouzil 1999; Liu & Peng 1999).It is inevitable that many types of metal cations are present in ore pulp. These metal cations significantly influence the flotation of minerals. Liu et al. (2015) showed that Ca2+ and Mg2+ could improve the floatability of spodumene at pH 12.5 and 10.0, respectively. The authors proposed that Ca2+ and Mg2+ ions readily form hydroxy complexes (CaOH(l) and MgOH(l)) and precipitates as (Ca(OH)2 and Mg(OH)2) in strongly alkaline solutions. Fan and Rowson (2000) investigated the effect of Pb(NO3)2 addition as an activator on ilmenite flotation and showed that it could improve ilmenite floatability. The addition of Pb(NO3)2 resulted in an increase of ilmenite zeta potential in both weakly alkaline and acidic aqueous solutions. Mehdilo, Irannajad, and Rezai (2015) studied three kinds of ilmenite of different origins and discovered that both Mg and V had a negative correlation with ilmenite flotation, while the Mn content seemed to correlate positively with flotation efficiency. A number of studies have also showed that Fe3+ can improve the floatability of ilmenite (Fan et al., 2009; Nuri, Mehdilo, & Irannajad, 2014)."

Jan 1, 2016

By Arnfinn Prugger

"The construction of the new Scissors Creek shaft at the Rocanville mine, the first potash shaft successfully completed in Saskatchewan Canada since 1979, is summarized here. Located 15km from the existing Rocanville surface plant, this new 6 m inside-diameter, 1121 m deep service shaft was built for fresh-air ventilation and access. Shaft construction in the Saskatchewan sedimentary basin involves sinking through five different rock-types: glacial tills, shales, sandstones, carbonates and salts. The first four rock- types are all water-bearing, and the salts will dissolve in water. This results in five different sinking challenges and requires five different shaft lining designs. The upper 580 m of rock (the till – shale – sands sequence) was frozen before sinking, and grouting methods were used for water control through deeper carbonate levels. Challenges that were faced and overcome during shaft sinking are reviewed, and ideas that future operators working in sedimentary basin environments might consider in order to avoid these difficulties are discussed.INTRODUCTIONThe Nutrien Inc. (formerly Potash Corporation of Saskatchewan Inc. / PotashCorp) Rocanville potash mine in southeast Saskatchewan, Canada has been in continuous production since 1971. Devonian potash, formed approximately 380 Mybp, is mined in a sedimentary basin environment at approximately 1000 m depth below surface in this area of Saskatchewan. The predominant use for finished potash products is fertilizer: potash fertilizer is concentrated and nearly pure KCl (i.e. greater than 95% pure KCl). Currently 10 potash mines are in operation in Canada, all in Saskatchewan. In 2018 Saskatchewan mines produced ˜ 23 million tonnes of finished potash products, which is approximately 35% of World demand of ˜ 66 million tonnes for the year (e.g. Nutrien Inc., 2019).In November, 2007 it was announced that the Rocanville potash mine would be expanded to increase production from 3.0 Million tonnes per year (Mtpy) to approximately 6.0 Mtpy of finished potash products, requiring an increase in hoisting capability from approximately 9.0 Mtpy to over 18.0 Mtpy. The Rocanville potash mine has historically been accessed through two shafts: a production and ventilation exhaust shaft, and a service and ventilation fresh-air shaft located approximately 200 m from each other. All surface offices, processing facilities, etc. are situated near these original shafts.A very important part of the recent Rocanville expansion involved the construction of a new service shaft (6 m diameter, 1121 m deep) for fresh-air ventilation and access, approximately 15km west of the existing surface plant. Once this third shaft was completed in 2015, the historical service shaft was converted to a second exhaust and production shaft. Three shafts are now available for mine access, ventilation and ore hoisting at Rocanville. As of December 31, 2017, annual nameplate capacity for Rocanville was 6.5 million"

Jan 1, 2019

By D. C. Peck, James. R. S., Chubb. P. T.

"Abstract -The East Bull Lake gabbro-anorthosite intrusion is one of several Early Proterozoic layered matie intrusions occurring along the Southern Province - Superior Province boundary in the Elliot Lake - Sudbury region, Ontario. The base of the East Bull Lake intrusion comprises abundant plagioclase cumulates (Leucogabbronorite Zone) hosting two distinct styles of sulfide mineralization: (1) disseminated magmatic sulfides, and (2) disseminated to massive, structurally controlled sulfides. Both types of mineralization are enriched in Pd, Pt, Au, Cu and Ni. The host rocks to the sulfide mineralization display a range of interesting features including nodular textures, dendritic­ pegmatitic matie pods, inclusion-rich zones (pyroxenite, anorthosite and granitic inclusions) and mag­ matie breccias. Disseminated chalcopyrite, pyrrhotite and pentlandite occur in concentrations of up to lOOJo within erratically distributed gossan pods near the base of the intrusion. The sulfides were originally precipitated from intercumulus liquids, but were subsequently recrystallized and locally remobilized along fractures during the major period of metamorphism and deformation that af­ fected the East Bull Lake intrusion. The base- and precious-metal tenor of the structurally controlled sulfides can be explained by extensive remobilization and reconcentration of the pre-existing magmatic sulfides in the vicinity of a major shear zone. Both styles of sulfide mineralization locally contain ppm abundances of POE + Au and are generally Pd- and Cu-rich, although both display large variations in Pd :Pt and Cu:Ni ratios. The magmatic sulfides are more strongly enriched in POE and contain up to 1470 ppm Pd in 100% sulfide. Severa! factors, including source characteristics, magmatic processes (crustal assimilation, fractional crystallization) and post-magmatic inter­ action with hydrous fluid, have influenced the present distribution of POE, Cu and Ni in the East Bull Lake intrusion .The magmatic sulfide occurrences from the East Bull Lake intrusion compare favorably with marginal-type deposits from rift-related intrusions (Noril'sk-Talnakh region, Siberia; Duluth Com­ plex, U.S.A.) in terrns of their distribution, but are most similar to reef-type POE deposits with respect to their base- and precious-metal geochemistry. The combination of high POE tenors and large tonnages that is observed for the POE-Cu-Ni mineralization from the East Bull Lake intrusion suggests that a good potential exists for the presence of economie concentrations of Pd, Pt, Au, Cu and Ni in the intrusion. On a global scale, the East Bull Lake intrusion is part of a suite of Early Proterozoic plutons, many of which contain significant volumes of stratiform and/or marginal­ type POE-Cu-Ni mineralization. The East Bull Lake intrusion is also one of the oldest mineralized intrusions derived from a sub-Superior Province mantle source region that has given rise to several significant magmatic POE-Cu-Ni deposits during the period 2.5 Ga to 1.1 Ga."

Jan 1, 1993

By K. A. Clark

SEPARATION of the oil from the bituminons sands of the Athabaska area of Alberta has been a subject of study by the Research Council of Alberta. The results of the study have been published in the Annual Reports of the Council. However, the last Annual Report in which there is mention of bituminons sand separation is that for 1934. The attention that is being directed toward the bituminons sands at the present time calls for an up-to-date summary of the work of the Research Council of Alberta on the hot-water separation process. STATEMENT OF FUNDAMENTALS OF HOT-WATER PROCESS Studies of the hot-water separation process have been largely empirical in nature. The objective sought has been a complete recovery of oil from the sand in the form of a separated oil which, itself, is free from mineral matter. Various procedures have been tried in the hope of attaining this objective and a very considerable mass of observations and background of experience have been acquired. lt is rime that a theory for hot-water separation should commence to emerge. As a start toward the formulation of such a theory, the statements which follow regarding the constitution of bituminons sand and its reactions with water and air are presented. It is not pretended that they are entirely correct, but it is believed that they lie not far from the truth. (1) Bituminons sand is an aggregate of sand, clay, oil, and water. The sand consists mainly of quartz particles of 100 ta 200 mesh size and smaller, but also of particles of other minerais including mica, rutile, ilmenite, tour-maline, zircon, spinel, garnet, pyrite, and lignite. Clay occurs interbedded with the bituminons sand, of which, also, it is a constituent. lronstone nodules of all sizes up to eight inches in diameter are likely to be present in the bituminons sand beds. The oil is viscous, naphthenic, and of a specific gravity slightly greater than that of water. The oil content ranges up to, and sometimes even exceeds, 17 per cent by weight. Rich bituminons sand from beds not invaded by water has a water content of 3 to 5 per cent by weight. The water is probably present as a film around the sand particles. The oil surrounds the moist sand grains as an envelope. (2) Water wets quartz and other siliceous minerals more readily than does mineral oil. Consequently, water tends to displace the oil film surrounding the quartz and other siliceous particles when the bituminons sand is mixed with water. Whether the oil is completely displaced depends on the properties of the water. That is to say, the materials dissolved or suspended in the water modify its wetting properties.

Jan 1, 1944

"The Companion Policy is guidance and not law. It sets out the views of the Canadian Securities Administrators (CSA) at to the manner in which the CSA interprets and applies certain provisions of NI 43-101 and Form 43101F1. The Companion Policy references the CIM Best Practice Guidelines for Mineral Exploration, and the Mineral Resources and Mineral Reserves, and that they should be followed by Qualified Persons.COMPANION POLICY 43-101CP TO NATIONAL INSTRUMENT 43-101 STANDARDS OF DISCLOSURE FOR MINERAL PROJECTS This companion policy sets out the views of the Canadian Securities Administrators (the “CSA”) as to the manner in which the CSA interprets and applies certain provisions of National Instrument 43-101 and Form 43-101F1 (the “Instrument”), and how the securities regulatory authorities or regulators (the “Securities Regulatory Authorities”) may exercise their discretion in respect of certain applications for exemption from provisions of the Instrument. PART 1 APPLICATION AND TERMINOLOGY 1.1 Supplements Other Requirements – The Instrument supplements other continuous disclosure requirements of securities legislation that apply to reporting issuers in all business sectors. 1.2 Evolving Industry Standards and Modifications to the Instrument- Mining industry practice and professional standards are evolving in Canada and internationally. The Securities Regulatory Authorities will monitor developments in these fields and will solicit and consider recommendations from their staff and external advisers as to whether modifications to the Instrument are appropriate. 1.3 Application of the Instrument -The definition of “disclosure” under the Instrument includes oral and written disclosure. The Instrument establishes standards for disclosure of scientific and technical information regarding mineral projects and requires that the disclosure be based on a technical report or other information prepared byor under the supervision of a qualified person. The Instrument does not apply to disclosure concerning petroleum, natural gas, bituminous sands or shales, groundwater, coal bed methane or other substances that do not fall within the meaning of the term “mineral project” in section 1.1 of the Instrument. 1.4 Mineral Resources and Mineral Reserves Definitions - The Instrument incorporates by reference the definitions and categories of mineral resources and mineral reserves as set out in the Canadian Institute of Mining, Metallurgy and Petroleum (the “CIM”) Definition Standards on Mineral Resources and Mineral Reserves (the “CIM Definition Standards”) adopted by the CIM Council on November 14, 2004, as amended. 1.5 Best Practices Guidelines for Mineral Resources and Mineral Reserves - A qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow the CIM Estimation of Mineral Resources and Mineral Reserves Best Practice Guidelines adopted by CIM on November 23, 2003, as amended. These guidelines are posted on www.cim.org."

Jan 1, 2003

By J. R. Kish, J. Dabrowski

"The susceptibility to intergranular corrosion modes is a major technical issue preventing widespread utilization of higher strength welded AA7xxx extruded beam profiles, in the peak-aged T6 condition, in automotive bumper assemblies. A study was undertaken to evaluate the relative exfoliation corrosion resistance (ASTM G85-A2) as a function of joint design parameters, namely the base alloy composition, heat-treated condition and beam orientation after exposure to a cyclic acidified salt spray test. This paper documents the major findings extracted from this study.INTRODUCTIONBumper systems play a predominant role in the passive safety of an automobile, since they are one of the main structures for absorbing the collision energy in the event of an automobile crash. Heattreatable AA6xxx-series (Al-Mg-Si) and AA7xxx-series (Al-Zn-Mg) Al alloys, with relatively high strength, toughness, energy absorption, weldability and formability, make it possible to design costcompetitive bumper systems to crush in a controlled fashion. In this context, Cu-lean AA7xxx extrusions, such as AA7003 and AA7108, which exhibit higher strength than AA6xxx extrusion, such as AA6082, represent an attractive light weight material from which to fabricate bumper assemblies (Clausen et al., 2000; Pedersen et al., 2008; Chen et al., 2009).Arc welding is a key joining process for AA7xxx alloys within the transportation industry. A major technological issue preventing widespread utilization of arc-welded AA7xxx joints is the susceptibility to severe localized corrosion (Kent, 1970, Reboul et al., 1985; Holroyd et al., 1987). It generally occurs as exfoliation corrosion within a heat affected zone (HAZ) a few millimeters from the weld bead, or a type of stress corrosion cracking (weld-toe cracking), which initiates at the weld toe and propagates into the interfacial region between the weld bead and the HAZ (so called “white zone”). In addition to the micro-galvanic cell activity induced by the intermetallic compound constituent and strengthening particles present, there is strong evidence that macro-galvanic cell activity between the weld bead and base AA7xxx alloy may be playing a controlling role. Electrochemical profiles taken across fusion welded joints, in cross-section, during exposure to saline solutions suggest that a significant potential difference exists across the AA7xxx arc-welded joint (Shumaker et al., 1967; Grauer and Wiedmer, 1980; Tuck, 1985, Onoro and Ranninger, 1993). These studies consistently show that the HAZ and base alloy are more electronegative with respect to the weld bead (arc-welded with AA5xxx filler wire). Despite this initial important work, the majority of the recent corrosion research effort on welded AA7xxx alloys has focused on the performance of friction stir welds (Lumsden et al., 1999; Wadeson et al., 2006; Hatamleh et al., 2009)."

Jan 1, 2012

By Baochun Wang, Hongli Jia, Zhaolian Wang, Fengliang Liu

"Promote and apply a new beneficiation technology and equipment effectively processing the refractory and medium-fine grained weak-magnetic minerals. HUATE® Forced-oil Cooling Vertical Ring WHIMS adopts the transformer oil cooling technology to cool excitation coils, solving the easily generated scaling problem resulting from water cooling, thereby to eliminate the demineralized water system. With <25 temperature ?raise, its magnetic field is stable. Wrapped by outer magnetic armor, it can generate a background intensity 1360kA/m. It effects very well in 1) wet preseparating the weak-magnetic coarse grains, like hematite, manganese ore, ilmenite, and purifying the concentrate; 2) removing the ferrous impurities and purifying the non-metallic minerals, like quartz, feldspar, kaolin; 3) enriching and recovering tailings from non-ferrous metals, like copper, lead, cobalt, molybdenum, thereby to greatly improve the mine resource utilization. It has applied 14 relative patents in China, and the invention patent in 56 countries, like Russia, USA, Australia, via PCT international organization. HUATE® WHIMS has been applied and accepted in more than 100 mines in and out of China. Compared with water cooling vertical ring WHIMS, it’s energy-saving and water-saving, and avoiding generating the scale. While compared with JONES WHIMS under the same separation indexes, it’s featured of more space-effective, lighter, lower costs, higher gradient, higher efficiency, larger processing capacity and wider grain application scope. Greatly promoting development of mineral processing technologies, HUATE® WHIMS is the equipment to reduce costs and improve efficiency urgently needed by the mine enterprises now.INTRODUCTIONAt present, influenced by the price and production factors, the international market demand for the grade of iron ores is increasing continuously. Restricted by the ore occurrence state, the beneficiation technology level and product economic value, every year the stope strips the stockpiling and discards hundreds of millions of tons of waste rocks containing iron, especially the weak magnetic hematite and limonite with <20% Fe%. The utilization technological bottleneck of these waste rocks makes their concentration ratio as high as 5-6, which leads to the huge wastes of energy, materials and beneficiation reagents and the increase of production costs. The effective solution is to improve the selected Fe% of the waste rocks like hematite. With the successful application of HPGR technologies in Chinese large iron mines, the mill feeding size has been reduced to 6-0 mm or 3-0 mm from the original 15-0 mm in the crushing system with 3 stages of crushing and 1 stage of closed circuit. This creates the conditions for the wet separation and recovery. While for the medium-fine grained weak-magnetic minerals, it lacks of the effective separation and recovery equipment in the world, which’s badly in need of R&D of the medium-fine grained high gradient wet strong magnetic preseparation equipment."

Jan 1, 2016

"6.1. Mineralogical Techniques ApplicableTo the Platinum-Group Elements6.1.1. IntroductionThe named platinum-group minerals (PGM) usually occur as grains smaller than about 200 microns and, even when present as larger grains as in nuggets, these are often complex multimineral intergrowths. Therefore, the PGM must be examined by microscopic techniques and, because all named PGM are opaque, they are suitable for microscopic study by reflected light. Special techniques for concentrating PGM and preparing suitable polished sections are detailed in Chapter 5. Another characteristic of the PGM is that the majority have very high reflectance at 589 nm, i.e., over 450Jo, but they range from about 38 to 74%. In contrast, micro-indentation hardness has a wider range from - 60 to - 3,000 kg I mm, and the PGM range from brittle to malleable.The small grain-size of PGM imposes certain limitations, or complications, on the usual mineralogical determinative methods of reflectance, micro-indentation hardness and X-ray diffraction. In addition, certain combinations of elements in some PGM render electron-probe analyses difficult. The usefulness and shortcoming of these methods, as applied specifically to the PGM, are discussed in the following sections. These are not, however, meant to be exhaustive descriptions of the techniques, which are fully described in other texts.6.1.2. Micro-Indentation HardnessDetermination of the Vickers Hardness Number (VHN) is discussed in detail in recent publications, such as Bowie and Simpson (1977) and Craig and Vaughan (1981). In addition, the recommendations of the Commission on Ore Microscopy (COM) of the International Mineralogical Association (IMA) are given by Criddle (1980). The usual small grain-size of the PGM, however, precludes the widespread use of this technique and very few PGM have, in fact, had their VHN determined at the COM-recommended standard load of 100 gf (cf. Cabri, 1981b, in Chapter 7). Examination of VHN data reported in the literature reveals that the few PGM whose microindentation hardness has been measured have incomplete VHN data, measured with loads other than 100 gf (Chapter 7). The small grain-size may also result in unreliable VHN data because, even though the correct load may have been applied, a thin grain will give erroneous data due to the matrix, or the grain may even shatter or pop out of the section. On the other hand, micro-indentations may give useful qualitative diagnostic clues. Moncheite, for example, shows fractures near the indentation (Chapter 7, Plate 1). In other cases, intergrown PGM produce different-sized indentations: e.g., froodite-michenerite-gold in Cabri (1972); isoferroplatinumtulameenite in Cabri et al. (1973); michenerite-moncheite in Cabri and Laflamme (1976) and Chapter 7, Plate 1; altaitemichenerite- testibiopalladite in Hudson eta/. (1978) and Plate 1, Chapter 7."

Jan 1, 1979

By Staff

"The Weyburn Oil Field, located 80 miles southeast of Regina, Saskatchewan, was discovered by Central-Del Rio Oils Limited, in January, 1955. As of January 1st, 1959, the field had 357 wells capable of producing an estimated total of 45,100 barrels of oil per day.Highly portable, economical, drilling rigs are used to penetrate the pay at a depth of 4,400 to 5,100 feet. Presently, the complete drilling operation for an average field well, including drilling, coring, testing, and running casing, requires 12 days. Drilling procedures are conventional for a field of this depth and no serious problems exist. Central-Del Rio core the productive section of all their wells, which provides valuable information for well completions and reservoir studies. Production casing procedure is to set through the zone and perforate the productive inter-val. This was found advisable due to the lensing nature of the porosity and permeability throughout the reservoir, and to the high connate water saturation encountered in the tighter sections of the reservoir in the north and northeast areas of the field.Although a few wells in the field have produced naturally by flowing or pumping without acid treatment, it has generally been necessary to acidize the wells to make them commercial producers. To date, acid treatments appear to effect better stimulation of the limestone reservoir than fracturing treatments. Perforation sealing balls have been used as an aid in selectively treating all of the perforated interval.The majority of the field is on pump, producing at a low gas-oil ratio. The main part of the field has water-free production, with most of the water being produced in the north and northeastern area. Salt-water disposal is now available in the field through two disposal wells completed in the Basal Blairmore sand.The Midale Beds ""Marly"" and ""Vuggy"" zones form the principal reservoir, which is a stratigraphic trap, with the north and northeast edges terminated by a porosity and permeability pinch-out and the south-west and west edges bounded by water-laden porosity. There is no evidence to date of a gas cap. The reservoir apparently is producing on a fluid-expansion-type mechanism. The increasing water production in wells on the southwest and west edges of the field indicated water encroachment from these directions, and suggests some recovery energy may be available from this source.The total probable ultimate remaining recoverable reserves have been estimated at° 332,469,000 barrels of oil. Markets have not been able to keep up with the rate of development of the medium crude re-serves. However, it is felt strongly that substantial additional markets for Weyburn medium crude will be developed by the producers in the near future at realistic wellhead prices."

Jan 1, 1959

By Hidenori Hatta, Takero Watanabe, Hideo Yoshida

"The effect of the quenching rate on age hardening in an Al-6.0mass%Zn-0.75mass%Mg alloy sheet was investigated. The quenching rates and aging conditions were as follows: water quenching (WQ) or furnace cooling (FC) followed by pre-aging at 20°C,then artificial aging at 120, 160 or 200°Cwere performed. The peak strength of the FC and the WQ are very similarat120°C aging. It is important high strength was obtained even at the extremely slow quenching rate. On the other hand, the strength of the WQ significantly decreased compared to the FCat200°C aging. GP(I) zones were formed during the pre-aging at 20°C even if the cooling rate was very slow like the FC, and were transformed into the GP(II) ones at 70°C or higher and then into the ?’ phase. However, these zones were dissolved by reversion during heating to 200°C. Thus the strength of the WQ decreased. On the other hand, it is considered that an unknown cluster or GP zone with a thermal stability formed during the FC was not dissolved up to 200°C and was transformed into the ?’ phase. Therefore, a higher strength was obtained in the FC for the200°Caging.INTRODUCTIONAl-Zn-Mg alloys are widely available in commercial production because these alloy have lower quench sensitivity and can be produced by air cooling (AC). Heat treatable aluminum alloys are usually produced by water quenching (WQ) to increase their strength because a high cooling rate inhibits the precipitation of the stable phase during cooling and increases supersaturated solute atoms. However, Baba(1967)reported the strength of an Al-6%Zn-1.8%Mg(mass%) alloy without additional elements quenched by very slow cooling (15°C/min) was 96% of that quenched by WQ. Furthermore,the age hardening at room temperature (RT) occurs after annealing at 410°C followed by furnace cooling (FC, 0.5ºC/min or less)in these alloys. Therefore, the process of annealing at 410 to 430°C for 120 min followed by AC, and reheating at 230°C for 240 min, then cooling is recommended in the specifications (Japan Aluminum Association, 2011). Matsuda and Yoshida(1996)also recommended annealing at 300°C for Al-Zn-Mg alloy extruded products to inhibit age hardening at RT by precipitating the solute atoms and decreasing them in the matrix. It has been considered that the higher the content of excess quenched-in vacancy becomes by WQ, the higher aging rate at RT is obtained. Therefore,it is theoretically and commercially important to clarify the reason why the age hardening occurs relatively quickly in almost no excess quenched-in vacancies such as the FC, and why the same strength as the WQ can be obtained in the FC"

Jan 1, 2018

By M. Li, T. H. Dubaniewicz, H. N. Dougherty

"INTRODUCTION Underground mines have the risk of accumulation of gases if not ventilated properly or during and after emergency situations when ventilation controls become damaged or stop working. Common gases that are monitored in underground coal are carbon monoxide (CO), oxygen (O2), and methane (CH4). Methane is a gas found in coal and released through mining; its explosive range is between 5% and 15%. Methane is commonly monitored on all mining equipment and with handheld gas sensors carried by most underground coal miners. Fiber optics (FO) is a popular technology applied in underground mining, particularly for its electric isolation. Many miners are familiar with FO cables hung throughout the mine, which are primarily used in the communication of voice and data (Taylor et al. 2010). Advancements in laser and fiber optics have made this technology well suited for gas sensing the harsh environment of mining applications. The work of the U.S. Bureau of Mines on the use of fiber optic monitoring of gases in mines started in 1992. Dubaniewicz et al. (1992, 1993, 1995, 1999, 2003) developed prototype gas sensors, including methane gas sensors, for research purposes. Previous research (Dubaniewicz & Chilton 1992) identified potential fiber optic gas detection cross-sensitivities associated with the index of refraction of various gases. Index of refraction effects was noted for carbon dioxide (CO2), which is produced in significant quantities by mine fires or explosions. NIOSH released a broad agency announcement (BAA) for the development and demonstration of mine safety and health technology (CDC NIOSH 2017). The objective of this announcement was to validate a sensor, specifically fiber optic, for the mine environment and test it in an actual working mine. The RSL FO sensor “OptoSniff” provided from this work is capable of hundreds of sensing points over distances of up to 20 km, has a measurement range of 0.05% to 100%, senses in an oxygen- deficient environment, and has no gas cross-sensitivity (RSL, 2014). The RSL system is totally electrically passive outside the central control unit (CCU), which can be housed in an MSHA-approved explosion-proof (XP) enclosure or in a control room outside of the permissive area. The sensor was tested in dusty and signal loss situations, showing it is tolerant of dust, has functioned at signal losses up to 90%, and was successfully tested in a mine environment for a five-month period (Walsh et al. 2014). This paper describes how the RSL FO sensor is used for testing using smoke and its contaminants for applicability in emergency situations. The testing investigates individual contaminants such as CO2, temperature, and smoke. Each test was performed separately and methane concentration, laser power, and response time data were collected."

Jan 1, 2019

By Juergen Antrekowitsch, Stefan Steinlechner

"Waelz oxide from steel mill dust recycling is usually sold to the primary zinc industry, where it is first charged to the roasters to eliminate the remaining fluorides and chlorides. This limits the overall amount of secondary materials which can be used because of different operating problems in the roasters. Another option, in the case where the halides are low, would be direct leaching with low or medium concentrated sulphuric acid. Unfortunately, because of the carryover of some steel mill dust, iron is also present in the Waelz oxide, reaching contents up to 5 wt.%. Since the objective is to treat the solution more or less directly by electrowinning, with only a few simple preliminary purification steps, iron in the solution is a very important factor. Various trials have been done to investigate the dissolution behavior of the iron contained in the Waelz oxide. Although the zinc extraction should reach a maximum, all other elements, especially iron, should be low. This paper describes the results of our research in this area and offers possible options for Waelz oxide utilization. There is also a focus on how other elements, present in the material, influence the dissolution behaviour of zinc and iron, and whether a loss of zinc is unavoidable, if low iron dissolution is required.INTRODUCTION One of the most important secondary zinc resources is the zinc oxide originating from steel mill dust recycling. For the treatment of high zinc containing steel mill dusts, the Waelz kiln process is the so called “best available technology” and it dominates the industry, with roughly a 90% market share. The product Waelz oxide contains mostly zinc oxide, but it also contains lead compounds and halides due to evaporation with the zinc. In addition, it contains iron and some slag compounds due to mechanical carry-over. The presence of halides limits the use of the material as an alternative concentrate for primary zinc electrowinning. Such halides can be reduced to a certain extent by washing and/or solvent extraction (see following chapter). Although lead is not troublesome and theoretically represents a second recoverable valuable metal, iron is unwanted and causes additional problems during leaching. Even though Waelz oxide is generally a highly welcome input material in primary zinc metallurgy, due to its high zinc content, it still contains halides, and in the majority of cases, the oxide must first be treated in a roasting process. Different circumstances, like accretion formation because of the lead and halogen compounds as well as unwanted cooling effects in the roaster, limit the amount of Waelz oxide which can be substituted for the primary concentrate. Another, even more limiting factor, is the allowable concentrations of chlorides and fluorides in zinc electrowinning, the last step in the primary zinc processing route (Ruetten, 2011)."

Jan 1, 2016

By N. Katsikaros, A. Lewis-Gray, P. Richards

"To optimize gold recovery in complex leach-to-electrowinning processes, Gekko Systems developed the Gekko resin exchange column (G-REX) as an intermediate step, using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin. Operational experience has been gained at the Castlemaine Goldfields Ballarat gold mine. In near-continuous operation since 2008, the Ballarat plant treats unclarified concentrate leach solution. The extension of this technology to higher throughputs and more complex chemistry is discussed.RÉSUMÉ Afin d’optimiser la récupération de l’or dans des procédés complexes impliquant la lixiviation suivie de l’extraction électrolytique, Gekko Systems a développé la colonne Gekko de résines échangeuses d’ions (G-REX) comme étape intermédiaire, à l’aide d’une résine hautement sélective pour la récupération de l’or qui permet d’isoler les métaux contaminants. Gekko détient la licence exclusive pour la résine AuRIX®100 produite par Purolite, et la colonne G-REX a été spécifiquement conçue pour cette résine. C’est à la mine d’or Ballarat de Castlemaine Goldfields que l’expérience opérationnelle a été acquise. L’usine de Ballarat, en exploitation quasi-continue depuis 2008, traite une solution concentrée non clarifiée de lixiviation. L’extension de cette technologie à des capacités supérieures et à une chimie plus complexe est examinée.AURIX®100 RESINAuRIX100 resin is a crosslinked polystyrene alkaline resin developed by Henkel (Virnig, Mackenzie, & Adamson, 1996). The resin beads are off-white in colour and spherical, with a nominal size of 100% +600 µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal–cyanide complexes from leach solutions with a pH of less than 11.5. The higher end of the pH scale produces the best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX100 resin for use in its G-REX column, as part of its unique suite of gravity gold–handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realized with AURIX100 resin: approximately 4–12% in capital savings and 27–40% in operating costs (Virnig, Mackenzie, Katsikaros, & Gray, 2004). Additionally, AuRIX100 resin is not susceptible to fouling; that is, the resin does not load with inorganic salts or organic compounds that would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, a dilute acid wash is periodically conducted in service on the resin to unblock resin pores."

Jan 1, 2017

By Martin G. Wafforn, George J. Greer

"In early 2014, Pan American Silver Corp. commenced a project to construct a second shaft at its La Colorada underground mine located in Zacatecas State in Mexico. This was the first new shaft development project undertaken by Pan American Silver in the history of the company. The existing mine workings permitted the use of a raise bore for the excavation of the shaft opening, utilizing directional drilling in poor ground conditions to advance the pilot hole. This was an interesting project with many challenges and successes, and numerous lessons learned. The project was successfully completed in 2016, with the shaft operating at full mine production capacity within weeks. INTRODUCTION The La Colorada Mine has a long history dating from at least the 1920’s. The mine is located in the northern portion of Zacatecas State in Mexico in the Chalchihuites area, an approximate two hour drive south from the city of Durango. Pan American Silver acquired the La Colorada mining concessions in 1998, with mine production at that time consisting of only a few hundred tonnes per day. Over the course of the following 15 years, with the addition of an oxide processing plant and some expansions to the sulphide processing plant and site infrastructure, production was eventually increased to a maximum of 1,250 tonnes per day, all of it generated from conventional cut-and-fill stopes in the underground mine. An existing shaft was used to hoist the ore to surface, and over the years Pan American Silver had deepened the shaft and had changed out some of the hoisting plant. However, there were historic workings in close proximity to the shaft that made it unsuitable for personnel transport, and shaft maintenance was becoming difficult. The shaft was increasingly considered as a risk to the long term production continuity, and also to further deepening of the mine. In addition, expanding the capacity of this old shaft was not possible. Drilling of the La Colorada mineralization at depth commenced in 2010, with very good exploration success. As a result, by the end of 2013, the mine reserves had grown to a total of 6.5 million tonnes of high grade ore (388 g/t Ag, 0.36 g/t Au, 2.4 % Zn, and 1.3% Pb). Furthermore there were more (and higher grade) sulphide reserves than oxide reserves at depth. Following the completion of an internal study in 2013 with assistance from one of the international shaft contractors, a decision was made to increase the production from the mine with the construction of a new shaft and a new sulphide processing plant, a project with a calculated payback of 2.2 years."

Jan 1, 2019

By D. Virely, M. Gasc-Barbier, J. Guittard

"The valleys of the Dordogne and the Vézère (France) have been inhabited since prehistoric times, as evidenced by the famous site of Lascaux. A few miles away, the village of La Roque-Gageac is also a very popular tourist destination (about 1.5 million tourists per year): The village is sandwiched between a massive limestone cliff and the Dordogne river. The collapse of a cave roof high above the village in January 2010 led us to characterize instability together for the cave and the whole cliff and propose a adapted instrumentation to monitor the fracture openings in the rock mass that are linked to climatic variations. Measurements have been going on and been recorded for nearly 4 years. They point out the role of thermal stress fatigue in the breakdown of the rock mass. In this paper we describe the site under study, the instrumentation and its main results. INTRODUCTIONThe phenomenon of thermal fatigue has been very little studied as far as rocks are concerned, whereas it is rather well characterized for other types of materials: Elsevier published a journal dedicated to fatigue (International Journal of fatigue). In the case of rocks, thermal phenomena and their impacts on mechanical behavior have been analyzed from a micro-structural point of view, and it is now well-known that an increase in temperature causes a dilatation of crystals (Arnould et al., 2004; Berest & Weber, 1998). This dilatation may lead to the development of inter-granular traction and compression stresses, and if those stresses are greater than fracture strength, inter-granular and intra-granular cracks may take place. On the other hand, the fatigue phenomenon (cyclic repetition of a temperature variation which is less extreme than the one that may lead to this inter-granular or intra-granular fracture) is a phenomenon which has not been much studied.The principal studies on thermal fatigue on rocks come mainly from the field of geomorphology, particularly in connection with the analysis of the evolutions of past climate that can explain the present shapes of those landforms: those studies remained essentially qualitative and not quantitative. Le Ber & Oter Duthoit (1987) proposed a thermal and thermodynamic approach to analyse the disaggregation of rock masses. This analysis is dedicated to the study of paleoclimates and was implemented to better understand the formation of slope deposits in order to propose transfer models permitting the reconstruction of the climactic conditions contemporary to their appearance. Since deterioration in the cliff only appears after several cycles, it means that it is a gradual and irreversible deterioration which leads to an increase of the « disorder ». Seen from a macroscopic system point of view, this irreversible evolution is quantified by the internal creation of entropy."

Jan 1, 2015

By G. Azimi, C. A. Ang, F. Zhang

"Nickel recovery from laterite ores generates large amounts of solid and liquid wastes. This is primarily due to the low concentration of Ni (about 1.4 wt%) in the feed ore to the High-Pressure-Acid-Leaching (HPAL) process. It is known that the HPAL residue contains a high concentration of hematite, a commercially important source of iron in the steelmaking industry. However, the balance is natroalunite, containing sulfur, which is a detrimental element in the steelmaking process. Hence, to make the HPAL residue a suitable feed for steelmaking, natroalunite must be removed. The current work is focused on: 1) a thorough characterization of the HPAL residue obtained from Vale, and 2) a systematic investigation of an alkaline leach process to remove natroalunite. The characterization results indicated that there are about 83 and 12 wt% hematite and natroalunite in the HPAL residue, respectively. The leaching results indicate that sodium hydroxide is the best leaching agent, which results in 55 wt% reduction in the sulfur content. The results of this work enable the conversion of an otherwise waste product into a useful feedstock for steelmaking. Furthermore, this project could potentially have significant environmental benefits by reducing the amount of residue produced during the HPAL process.INTRODUCTION Conventionally, crude steel has been obtained by reducing iron ore containing oxides such as hematite (Fe2O3), magnetite (Fe3O4), and wüstite (FeO) in a blast furnace with coke. The product is then refined in a basic oxygen furnace to produce steel with useful properties (McGannon, 1969; Turkdogan, 1978). Steel has been sought for its desirable properties and its application is widespread throughout modern civilizations. Surpassing the growth rate of other materials, the annual demand of steel has increased at a compound growth rate of 5% over the last 20 years (Baddoo, 2008). The global demand for steel was reported to be 1501 Mt in 2016 and demand is expected to double by 2050 (Cullen, Allwood, & Bambach, 2012; World Steel Association, 2016). In recent years, to meet the rapid growth of demand, secondary resources for iron have been identified as strategic sources of iron (Das, Kumar, & Ramachandrarao, 2000; Li, Sun, Bai, & Li, 2010; Matschullat et al., 2000). The residue produced from high-pressure acid leaching (HPAL) of laterite ore has been identified as one of the important secondary sources of iron (McDonald & Whittington, 2008). Laterite ore represents 60% of the world’s nickel resources and accounts for approximately 40-50% of the world annual nickel production (U.S. Geological Survey, 2016). Therefore, the amount of iron residue produced by the process is substantial and its utilization will produce both economic and environmental benefits."

Jan 1, 2017

By Robert A. Brown

"The O'Brien mine is in the west-central part of Cadillac township along the Cadillac 'break', which extends for 7,500 feet from west to east across the property.The ground was staked in 1924 by A. Dumont and W. Hermeston, prospecting for M. J. O'Brien, Limited. The first vein discovered is that now known as No. 1. The No. 4 vein was later exposed on the surface; the other veins known to be present were revealed by underground work and diamond drilling carried out both from the surface and underground.The mine is developed from three vertical shafts: No .. 2 extending from the surface to 2,000 feet; No. 3 from the surface to 1,500 feet; and No. 4 from 2,000 to 3,000 feet. There is on the property a mill of about 200 tons a day capacity, the usual shops, and a townsite housing about forty-five families. Gold production to the end of September, 1944, amounted to 295,824 fine oz. from ore having an average grade of 0.505 oz. a ton. In addition, the mill recovered 3,237 tons of arsenic trioxide having a purity of 83 per cent As2O3.GENERAL GEOLOGYThe four main groups of rocks of the Cadillac area- the Cadillac, Blake River, Kewagama or Pontiac, and Malartic- are found within the boundaries of the property. However, as these rocks have been fully described in · various government reports (1,2,3,4,5,6) and all the known orebodies occur within one group- the Blake River-a detailed description of the geology will be dispensed with here. The known ore deposits lie south of the Cadillac 'break' in a group of rocks that includes 'greenstones', greywackes, conglomerate, porphyries, and a rock of gabbroic composition that may be intrusive. Both flows and tuffs can be recognized in the 'greenstones'. The two bands of porphyry that trend easterly across most of the property have been considered by some observers to be dyke rocks and by others to be flows. Certain evidence points to their being dykes that were intruded as sills considerably prior to the emplacement of the gold-bearing veins, but the possibility of flow origin cannot be fully rejected. North of the talc-chlorite-carbonate schist zone forming the 'break' the rocks are conglomerate and greywacke with iron formation, in which there are no known veins of ore grade. Within the schist zone are minor acid and basic intrusives. The general trend of both bedding and schistosity is a few degrees south of east. The dip is generally vertica1 or steep to the south."

Jan 1, 1954