Search Documents

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing a/l essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.IntroductionVery high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field.However, sulphur content, mainly pyritic, ranges from 1 to 2.5070. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required .Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs.Typical data on the various coal properties of importance in the production of coke are included in Table I. Necessity of Low-Gravity SeparationThe design of any coal preparation plant requires the study of washability properties of the coal to be treated to determine the quantity and quality of coal produced at a given specific gravity along with the difficulty in accomplishing that separation.Their low ash content allows the important washability aspects of Harbour seam coals to be represented by sulphur! specific gravity curves (Fig. I). This particular example indicates that a yield of 54.5% is attained, at a sulphur content of 1.20%, for a perfect separating device operating with a 1.29 S.G. cut point.Material rejected from this separation still contains usable coal, which is recovered as middlings by separating at a higher gravity."

Jan 1, 1980

By David Deglon, Martin Harris, Mehdi Safari

"This study investigates the effect of energy/power input on the flotation of a platinum ore in a pilot-scale oscillating grid flotation cell. Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Secondary rougher feed and primary cleaner tail streams were floated in a pilot-scale oscillating grid flotation cell at power inputs from 0 to 2.5 W/kg, using 0.50 and 1.50 mm bubbles. From this study one may conclude that the effect of energy/power input on the flotation rate is strongly dependent on the particle and bubble size. Flotation rates generally increase with increasing particle size and decreasing bubble size. Increasing energy input generally leads to an increase in the flotation rate for finer particles and an optimum flotation rate for intermediate & coarse particles. Optimum conditions for intermediate/coarse platinum ore particles are using small bubbles at low energy inputs, or large bubbles at higher energy inputs. These results suggest that higher energy inputs are generally beneficial for the flotation of platinum ores as these consist predominantly of finer particles (-75 µm) and most industrial flotation applications operate with larger bubbles (1.0-2.0 mm).INTRODUCTIONThere is a considerable body of experimental and theoretical evidence to suggest that energy/power input plays an important role in flotation kinetics, particularly in the finer particle sizes where flotation efficiency is poor (Deglon, 2005). A number of excellent studies into the effect of energy on flotation kinetics have been carried out in impeller stirred cells (Ahmed and Jameson, 1985; Deglon, 2002; Pyke et al., 2003; Newell and Grano, 2006). Investigations using this type of cell have a number of limitations. The impeller influences particle suspension, bubble break-up and agitation in the cell. In addition, turbulence is highly inhomogeneous and anisotropic, with power intensities near the impeller orders of magnitude higher than those found elsewhere in the cell (Deglon, 1998; Koh and Schwarz, 2003; Schubert, 1999, 2008). These limitations have resulted in the development of novel cells for the investigation of energy input."

Jan 1, 2016

By P. Mayer

"Determining the correct mechanism of a boiler tube failure is important for the prevention of future tube failures. Proper corrective measures can be undertaken to alleviate the root cause or causes for a failure only when the correct mechanism is known. A mechanism of boiler tube failure is defined as the process which degrades the tube and produces a failure.An expert system package was developed for use by electric utility power plant personnel during investigation into the cause of a boiler tube failure. It is intended to assist their efforts to recognize and identify a basic failure mechanism that can produce the type of boiler tube failure under investigation. The program guides the user to the most likely failure mechanism by asking simple questions, answers which can be obtained by determining the failure location, type of fuel, and from visual inspection of the failed tube. Expert systems are a form of artificial intelligence which imitate the decision-making process of experts.IntroductionBoiler tube failures (BTFs) continue to be the single largest source of forced outages in fossil fired electricity generating stations. Because of this a concentrated effort is being made to minimize boiler tube failure occurrences. Eliminating boiler tube failures could be worth $5 billion a year to the electric power industry(1).The aggressive service environment of fossil-fired boilers is largely the reason for these failures because the combined effects of stress, temperature, corrosion, erosion and vibration cause deterioration of boiler tube material properties and reduction in wall thickness.Determination of the boiler tube failure mechanism is important for the prevention of future problems. The root cause for a failure can be established and proper ameliorative measures taken only when the failure mechanism is identified correctly. The correct identification of failure mechanism is a complex process which may include many individuals and institutions. Technical specialists in metallurgy, chemistry, combustion, and boiler design frequently cooperate with the station staff in a failure investigation . These individuals rely on personal experience and numerous reports , theories, studies, private communications and investigations concerning the different failure modes and mechanisms."

Jan 1, 1990

By M. B. Kime

"Discrete-element method (DEM) modelling is a powerful tool for studying particulate systems within the mineral processing industry. DEM simulations were conducted to investigate the power draw, load behaviour, and impact energy profile of an experimental ball mill under different milling conditions. The variables considered were mill rotational speed (percent critical speed), ball size, and lifter face angle. The simulation results indicated that the grinding efficiency would be enhanced by using 80% critical speed, 30 mm ball diameter, and 45° lifter face angle. These findings can be useful in guiding actual ball milling tests involving an ore sample.RÉSUMÉ La modélisation par méthode des éléments distincts (MED) est un outil puissant qui permet d’étudier les systèmes particulaires au sein de l’industrie de traitement des minerais. Des simulations par MED ont été menées de façon à étudier le profil de la consommation énergétique, du comportement de la charge et de l’énergie de rupture d’un broyeur à boulets expérimental dans diverses conditions de broyage. Parmi les variables prises en compte figuraient la vitesse de rotation du broyeur (vitesse critique en pourcentage), la taille des boulets et l’angle de coupe de la cornière élévatrice. D’après les résultats de la simulation, on pourrait améliorer l’efficacité de broyage en utilisant une vitesse critique de 80 %, un diamètre de boulet de 30 mm et un angle de coupe de 45 ° de la cornière élévatrice. Ces résultats peuvent se révéler utiles pour les essais concrets de broyage à boulets impliquant un échantillon de minerai.INTRODUCTIONComminution is a very energy intensive process. It consumes approximately 5% of the electricity produced worldwide and more than 50% of the total energy used in mineral processing plants (Pokrajcic, 2010). Among all the comminution stages, ball milling is one of the most energy intensive processes. In ball mills, rotational movement provides the rise of the load and the media that are projected and impact on the mill shell at lower angular displacement, resulting in particle breakage. Ball mills are able to reduce particle size over a relatively wide range of particle sizes. This explains their wide applicability in research laboratories and the mineral processing industry."

Jan 1, 2017

By Y. Y. Yemelyanov, S. S. Gudkov, A. V. Boldyrev, A. V. Bogorodskiy, S. V. Balikov

"A series of tests to optimize pressure oxidation- carbon-in-leach process (POX-CIL) of goldbearing flotation concentrate with the addition of sodium chloride and activated carbon were carried out. Flotation concentrate which was generated during primary ores concentration from a large Russian deposit was used for these tests. The tests were performed with different concentrations of sodium chloride. It was found that the required sodium chloride concentration for gold leaching was 5 g/L. The tests performed with different additions of activated carbon showed that the amount of activated carbon should be at least 6% of the concentrate mass. The rate of sulfides oxidation was 67.7–99.8 %. The highest gold recovery was 98.6 %.INTRODUCTIONThe majority of gold-bearing ores are recommended to classify as amenable to cyanidation and refractory. Processes at elevated pressures and temperatures have become increasingly important in base metals hydrometallurgy (Lodeischikov, 1999, 2007; Naboichenko, Shneerson, Kalashnikova, & Chugaev, 2009; Thomas, 2005).Current pressure autoclaves – cyanidation flow sheets are capital intensive due to numerous circuits and the use of environmentally-unfriendly sodium cyanide. The use of halide-based lixiviants during pressure oxidation of precious metals can be a promising technique for refractory sulfide goldbearing mineral raw material hydrometallurgical processing (Fleming, 2002, 2007, Kotlyar, Meretukov, & Strizhko, 2005).In this paper, we presented the results of the research on finding the optimum process parameters of pressure oxidation using an adsorbent for a refractory gold-bearing concentrate. A proposed flow sheet involves (Bogorodsky, Yelelianov, & Balikov, 2012):1. Gold-bearing sulfides oxidation followed by precious metals dissolution and the formation of gold and silver chloride complex;2. Reaction of the precious metals chloride complex with a carbon-based adsorbent;3. Precipitation of precious metals onto the adsorbent by EW and smelting of cathode precipitates into Dore bullions.This process allows POX of gold-bearing sulfides, precious metals dissolution and their precipitation on the adsorbent to be executed in one single vessel. This study found that the most suitable lixiviant was sodium chloride. Fleming (2002) suggested that in the presence of a halide-based reagent (e.g. chlorine- ion reaction), the dissolution of gold during POX is achieved according to reaction 1:"

Jan 1, 2016

By M. R. Babcock

"The Rabbit Lake story began in the late sixties and will continue well into the twenty-first century. It is a story of success, of multiple ore body discoveries, of unique systems, and new methods made possible through innovative and state-of-the-art design. Two quite different geological systems host the five ore bodies mined, or slated to be mined. These two systems have yielded two distinct ore types, each with characteristic mineralogical properties and each requiring its own specific mill circuit.Emphasis on communications and our unique systems have led to a satisfactory and fulfilling work environment resulting in the historically low employee turnover which has contributed to the operation success.A comprehensive environmental study after twelve years of operation has given the Rabbit Lake Operation a completely clean bill of health. INTRODUCTIONRabbit Lake can be described as Saskatchewan's first highgrade uranium mining operation, which set the stage for the province's current role as the leader in uranium mining throughout the western world. The importance of the Rabbit Lake operations - past, present and future.LocationThe Rabbit Lake operation is located in northeastern Saskatchewan (Fig. 1)- 805 km north of Saskatoon, Saskatchewan, and 814 km northeast of Edmonton, Alberta. OwnershipGulf Minerals Canada Limited discovered the Rabbit Lake deposit in 1968. Mining operations began in 1975and were operated by Gulf until purchased by Eldorado Nuclear Limited in 1982. In 1988, Eldorado merged with Saskatchewan Mining Development Corporation (SMDC) to form Cameco-A Canadian Mining &. Energy Corporation. The new corporation is one of the world 's largest uranium companies.Cameco's $1.5 billion in assets include the Rabbit Lake uranium mine (Cameco 100010); the Key Lake uranium mine (Cameco 66.67%; Uranerz Exploration and Mining Limited 33.33%); the Cluff Lake uranium mine (Cameco 20%; Amok Ltd. 80%); the Fuel Services Division at Blind River and Port Hope, Ontario (Cameco 100%); and a 100%); and a 48.75% interest in the Cigar Lake uranium deposit which is now at the test mining stage (Cogema Canada Ltd . 32.625% ; Idemitsu Uranium Exploration Canada Limited 12.875%; Corono Grande 3.75%; Korea Electric Power Corporation 2%). In addition, Cameco is involved in a number of base and precious metal explor ation projects."

Jan 1, 1989

By D. M. Richards

"IntroductionThe Highland Valley Copper partnership was formed in July 1986 as a logical result of a mine with a large ore reserve but a small mill, and a mine with a large, modern mill but dwindling ore reserves. The original partnership of Cominco and Rio Algom was expanded in January 1988 to include Highmont Mining Company. During 1988/89 the Highmont mill was moved 7.5 km to adjoin the Lornex mill, becoming the Highland mill in the process, with a nominal capacity of 130 000 tonnes per day.The mine is located near the town of Logan Lake, 220 km northeast of Vancouver, British Columbia and 55 km southwest of Kamloops. The map in Figure 1 shows the general area. Kamloops is a major service centre and is served by two railways, two major roads and a regional airport. The mine site is situated between 1200 m and 1600 m above sea level on the Thompson Plateau. Principle activities in the area, in addition to mining, are cattle ranching and forestry. Ore reserves at the beginning of 1996 totaled 533 million tonnes at a grade of 0.42% copper and 0.008% molybdenum. Ore is mined from two pits — Valley, 3 km northwest of the mill; and Lornex, 1 km southwest of the mill. With 78% of the reserves, the Valley pit is the focus of activity.In order for Highland Valley Copper to remain competitive with a very low grade ore reserve, it has been necessary throughout the mine’s life for new technologies to be embraced as they become available. These have included such diverse technologies as in-pit crushing and conveying, large mechanical drive trucks, computerized truck dispatch and oneman survey instruments. During the next few years, it is planned to introduce two further technologies that are relatively new to both the world at large and the mining industry in particular. These are namely Global Positioning Systems (GPS) and Geographical Information Systems (GIS), both of which are expected to have a major impact on the way mining is carried out in the years to come."

Jan 1, 1997

By John J. Laffin

"Nova Scotia Department of Mines and Energy Throughout the history of Nova Scotia, trends in the production and use of its coal resources have resulted in major impacts on the economy and society of the province. Current trends in coal demand locally, nationally and internationally are having and will have an increasing positive effect on Nova Scotia over the next twenty years-in terms of energy supply, job creation and general economic development. Coal for electrical generation is an immediate and key objective of Nova Scotia's energy plan; and, in the long term, coal-derived fuels will meet the province's needs for transportation fuels. Demand for metallurgical coal is also expected to increase, especially if the merchant coke plant currently under investigation becomes a reality.Meeting these coal supply and utilization objectives in the face of increasing environmental, social and economic constraints poses a tremendous technical challenge. Work has begun on projects to expand coal production capacity and to adapt new technologies for coal preparation and utilization to the specific needs of Nova Scotia; much more work will be required in the coming decade in order to succesfully tap this resource.IntroductionThe energy problem facing Atlantic Canada has a few unique features not found in the rest of the country. Canada, as a whole, has access to a diverse mix of energy resources, including crude oil, natural gas, coal, hydro and uranium, with the result that crude oil supplies only about 40 per cent of Canada's primary demand. In contrast, foreign crude oil dominates Atlantic Canada's energy mix, supplying over 70 per cent of the primary energy demand.This results in important differences in various sectors. Nationally, about 5 per cent of the electricity is generated from oil whereas last year in Nova Scotia approximately 40 per cent of the electricity generated was from imported oil. Residential, commercial and industrial space heating, and industrial process heating in Atlantic Canada was almost 100 percent dependent on foreign oil. This is in sharp contrast to the situation in central and western Canada, which have access to secure domestic natural gas, oil and hydro electricity."

Jan 1, 1982

By W. C. Whittaker

Introduction When one thinks of a coal stripping deposit, the picture that usually comes to mind is that of a more or less flat seam from two to twenty feet in thickness overlain by ten to fifty feet of overburden, in suitable ratio for economic operation. This is the usual type of stripping deposit and is quite a common occurrence in various parts of the prairie provinces. Rather unusual types of coal stripping deposits are being presently worked as open-cut mines by Sterling Collieries, Limited, and the Co al Valley Mining Company, Limited, at Miles 47 and 48 on the Alberta Coal Branch, some 150 miles south west of Edmonton. These deposits are of interest chiefly because they represent turned-up and greatly thickened sections of the Mynheer seam, and as such they present their own problems, peculiar to the commercial exploitation of a seam of this type. The area in which these deposits occur was originally owned by the Pacific Pass Collieries, whose operations, however, were confined to under-ground mining at Lovett, some eight miles to the southeast. It was not until l918 that the value of these deposits was realized, when the Company now known as Sterling Collieries, Limited, opened their pit at Mile 47. At the inception of the work, coal was loaded directly into the railway cars by men using wheelbarrows. In 1920, a tipple was built, after which the coal was loaded by steam shovel into mine cars, hauled by steam dinkeys, and loaded over the tipple into railway cars. In 1922, the Coal Valley Mining Company entered the field at Mile 48, with an entirely mechanical equipment, and at the present rime these two are the only stripping properties in Alberta using mechanical equipment both for the removal of overburden and the loading of the coal. These Companies have operated continuously since that time, and have to date mined and shipped 4,000,000 tons of coal, and moved some 5,255,000 cubic yards of stripping. The present annual coal output for the two mines is about 240,000 tons.

Jan 1, 1935

By Neil Campbell

"The Pine Point area is on the south shore of Great Slave Lake, 510 air miles north of Edmonton and J JO miles south of Yellowknife, N.W.T. The occurrence there of lead and zinc was reported in J 899 by R. Bell (5) of the Geological Survey of Canada, and in the following years several claims were staked and some prospecting was done. In 1928 Atlas Exploration Co. took over the property containing the discovery occurrences. In 1929 The Consolidated Mining and Smelting Company of Canada Ltd. (""Cominco"") and Ventures Ltd. participated with Atlas in forming the Northern Lead-Zinc Co., which, under the direction of J. M. Bell, carried out 24,499 feet of drilling in the discovery and surrounding areas. Two shafts and many surface pits were also sunk. This work showed that the discovery deposits contain about 500,000 tons of lead-zinc ore, but no new orebody was found.In 1936 D. F. Kidd (11) drew attention to the highly significant space relations between the base-metal discoveries at Pine Point and the projections of certain major Precambrian faults mapped earlier by C. H. Stockwell. Geological work by Cominco in 1940 and subsequent years suggested the presence of mineable deposits within a belt of land including part of the area of earlier field work and extending far beyond it. Between 1946 and 1954 exploration financed by Cominco and Ventures Ltd. included 182,950 feet of diamond drilling, 383 feet of sinking, and 240 feet of drifting, raising, and crosscutting. This work was successful in finding substantial quantities of new ore in places where bedrock is completely concealed.The topography is one of low relief, characterized in many places by swampy muskeg and shallow, marl-bottomed ponds. The area where ore has been found is generally higher ground which, though not well drained, is comparatively dry. It is also marked by raised beaches and a few sand dunes overgrown by small spruce and pine. Bedrock is generally overlain by a variable thickness of hard, glacial boulder clay. This in turn is covered by silt, sand, and gravel, probably deposited from the waters of Great Slave Lake, which formerly extended many miles beyond its present southern shore."

Jan 1, 1949

By Frank Ebbutt

Introduction The property of the Britannia Mining and Smelting Company, Limited, is situated on the east side of Howe sound, about six miles from its head. It is roughly thirty miles by water from Vancouver, one of the important ports of the Pacific and the industrial and financial centre of British Columbia. Howe sound is navigable for ocean-going vessels and Britannia Beach is a daily port of call for the commodious boats of the Union Steam-ship Company, sailing from Vancouver. Few mines are so ideally situated or have so many or varied natural advantages. Copper was first found on Britannia mountain in 1888, by Forbes, but it was not until 1898 that five claims were staked here by Oliver Furry, a trapper. It is from these claims that the major production during the past thirty years has come. In 1900 the Britannia Copper Syndicate was formed and development of the property was commenced. In 1903 the late Grant B. Schley obtained control, and through his efforts the Britannia Mining and Smelting Company was organized in 1908 as a subsidiary of the Howe Sound Company. Since that time, a persistent and progressive policy has been followed, which has resulted in a prolonged and profitable operation. The country in the immediate vicinity of the mine is marked by strong relief, with mountains rising abruptly from tide-water to elevations of 5,000 feet and more. Two broad transverse valleys deeply dissect the area. These are the valleys of Britannia creek and Furry creek. The region has under-gone prolonged and relatively recent glaciation. Over much of the surface there is deep overburden and dense vegetation. The geology of the mine and vicinity has been described in reports by S. J. Schofield (1), H. T. James (2), J. G. Barry, and others (3). The present writer is in accord with much of this literature on Britannia, but during recent years, extended observations made underground have shown that the 'quartz porphyry', or 'mine porphyry', of several of the earlier writers is not the host rock to the commercial mineralization; and he contends that the mineralization occurs in highly altered phases of a complex series of ruffs, flows, and pyroclastics and their autoclastic metamorphosed products.

Jan 1, 1935

By M. Kuyumcu

With annual production of almost 3.5 million metric tonnes of K20, former East Germany (GDR) was the world?s third-largest producer of potash, ranking behind only the Soviet Union and Canada. More than 80 % of production was intended for export to earn urgently needed hard currency. For this reason, beginning in the 1970s, East Germany began to mine unprofitable hard-salt sources and carnallitite fields, which are geomechanically problematic. In the course of restructuring from a centrally planned to a market economy after German reunification, only two of the nine existing potash mines were classified as economically viable for privatization. All six potash mines in the South Harz Region were closed between 1991 and 1993. The orderly safekeeping of these potash and other decommissioned ore mines and the rededication of mining areas were assigned in 1992 to a German state-owned company GVV founded especially for this purpose. Elaboration in the present documentation covers the local necessity of the type and extent of filling and safeguarding measures. As a result of the remedial measures taken, it was possible to prevent the collapse of cavities and damage to surface facilities. This documentation describes the safeguarding successes to date, with appreciable reduction and stabilization of surface settlement and with significant lessening of seismic events. Also presented are concepts updated to the state of the art for safeguarding of numerous potash mining shafts for long-term effectiveness in separation of the workings and watercourse levels in the cap rock. In the course of 100 years of production, six mining dumps resulted with a total volume of approximately 170 million m3. They consist of up to 95 % of water-soluble salts. Every year, precipitation dissolves up to 500,000 tonnes of this salt, which enters as a highly concentrated solution into watercourses and ground water. Explanation follows of measures for minimization of environmental pollution by covering of dumps and controlled drainage of alkaline solutions from the dumps. Finally, presentation is made of the results of the successful work until now by GVV for reuse of decommissioned mining sites with settlement of new companies for creation of additional jobs and for revitalization of the monostructured South Harz Potash Mining Region.

Aug 1, 2013

"Yara Siilinjärvi in Finland is the Western Europe's only apatite mine. Annually it produces one million tons of apatite concentrate, which creates 10 million tons of tailings. At the beginning of 2017, Yara replaced their conventional TSF with a new tailings treatment plant, which increased the solids content of the slurry from 45–48% to 66–68%, making it possible to deposit as a paste. This extended the life-span of the current TSF from 2020 to 2035. This paper presents the storyline of the Yara paste plant project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After successful pilot trials, the final process design was implemented. Process automation played a key role in the project. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances. Since commissioning the paste plant has been running consistently with an underflow solids content of 66-68%, with average beach slope angles of 3.5 degrees in the tailings disposal area. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the plan. During first year of operation the plant’s availability has been very good, over 97%, and currently, the plant is operated remotely from the main concentrator plant.INTRODUCTION The Yara Siilinjärvi Plant is owned by Yara International, a Norwegian fertiliser company. Yara Siilinjärvi is Western Europe's only apatite mine, and it primarily produces apatite concentrate for its Siilinjärvi phosphoric acid plant. A portion of the concentrate is also dried and shipped to other Yara fertiliser plants. The site annually produces one million tons of apatite concentrate, which creates approximately 10 million tons of tailings. Extending the lifespan of the 1150-hectare tailings storage facility has been studied in Siilinjärvi for a long time. The aim has been to use the same tailings area footprint, without any new land purchases or major dam increases. An important part of the process has been to study the possibilities for using new technologies, especially thickened tailings technology (Ruhanen, 2014)."

Jan 1, 2019

By M. Sakata, H. Hata, K. Haiki

"Most of the secondary ZnO contains fluorine (F) in large quantities. Serious troubles at the zinc electrowinning are occurred by the cathode corrosion caused by F, therefore we developed iron compounds as F-adsorbents used in zinc sulfate solution. The iron compounds can be reused repeatedly as F-adsorbents because they can adsorb/desorb F alternatively depending on the pH. Moreover, if the adsorptive capacity decreases, we can dissolve and re-synthesize them easily. In this paper, results of the experimental process which consists of five steps (leaching, F removal, Cl removal, purification and electrowinning) to produce high purity electrolytic zinc from the secondary ZnO are reported. INTRODUCTIONThe recycle material for zinc, secondary ZnO, contains large amounts of fluorine (F) and chlorine (Cl) which are halogen elements, compared with calcine obtained by roasting of zinc sulfide concentrate. The halogen elements cause adverse effects in the zinc electrowinning process and particularly F causes corrosion of aluminum cathode plates and eventually sticking of electrodeposited zinc and therefore, F concentration in the electrolyte is controlled to less than approximately 20 mg/L. There are several methods to remove F from secondary ZnO, such as leaching with Na2CO3 or NaOH solution [1-2], vaporizing in a rotary kiln by roasting at 1000 to 1200 degrees C [3-4]. However, up to the moment, there has been no effective method for the removal of F from zinc electrolyte and it has been a big obstacle in treatment of secondary ZnO in electrowining of zinc.The authors, therefore, developed an iron compound used as an adsorbent of F in the zinc sulfate solution [5-8]. This iron compound is Akaganeite that has a crystalline structure of ß-FeOOH. Akaganeite is synthesized by neutralization of FeCl3 solution containing a small amount of SO4 2- with Na2CO3. When this iron compound is immersed into weak acidified zinc sulfate solution, F in the solution is adsorbed. F adsorbed in the iron compound is removed by immersing in weak alkaline solution and the iron compound can be reused as F adsorbent."

Jan 1, 2012

By Roderick C. McDonald

Great Bear lake, the fourth largest body of water on this continent, comprises an area of approximately 12,000 square miles, and is set astride the Arctic circle, with a large portion of it witnessing both the Arctic winter night, and the Arctic summer day with its midnight sun. The very name itself, Great Bear, suggests an Arctic region. The seasonal contrasts at Great Bear lake are very marked by the cold and darkness of winter, and the warmth and brightness of summer. Signs of winter such as low clouds, snow, sleet, fog, and night frosts, generally appear the latter part of August, while ice forming on bays during the last two weeks in September ends boat travel on the lake about September 30th.Early in June the ice leaves the river mouths, during the last ten days of the month it disappears from small bays, and at some time during the last two weeks of July the main body of the lake becomes navigable. In 1916, the ice disappeared earlier than usual, and the lake was navigable on July 5th. Great Bear river generally breaks up about June 1st, but, on account of ice cliffs and floes, it is not navigable with safety until early in July. Even then, the traveller is confronted with the Charles rapids, but these might be overcome by a wagon or motor road, such as the one from Fitzgerald to Fort Smith: However, in 1931, Mr. A. W. Boland, Fort Norman, N.W.T., carried with scow and motorboat practically all freight between Fort Norman and LaBine point and Hunter bay, at the east end of the lake. During July and August, two types of clothing are required, for, although the days are mainly ones of warm sunshine, the nights are cloudy and cold. In the winter season, fur clothing is used exclusively. Considerable timber, mainly white spruce, suitable for fuel and building purposes, borders the lake and extends eastward to the Coppermine river. North of the lake, no timber is found except in the river valleys, but with oil and coal possibilities near Fort Norman, the fuel situation might be solved.

Jan 1, 1932

By E. E. Mason

THE Myrtle group of mining claims is situated on Barkerville mountain in the Cariboo mining district of British Columbia, west of the old mining town of Barkerville. An 1,800-foot adit, known as the Shamrock tunnel, was driven in 1935-36 from the Barkerville road and in the general direction of the Myrtle group. It was proposed to enlarge this adit to more convenient section, extend it 2,500 feet int0 Myrtle ground, and from there drive a main entry 3,000 feet along the length of the group. Several laterals were also to be driven off this main entry as part of the tunnel schedule. It was thus originally proposed to drive 5,500 feet of new adit and 1,800 feet of laterals, a total of 7,300 feet of new work. Work was commenced with a bulldozer on April 21st, 1941, cutting a bench on the hillside for a plant site. The power plant was ready for operation on August 8th. Slashing and re-timbering of the old adit rook longer than was expected. It was found that 57 per cent of the length required timbering, chiefly by fore-poling, and there was also trouble in several sections with swelling ground. First round in the new face was taken on September 17th, when a 2-shift daily schedule was commenced. Due to delays in delivery of electrical equipment, it was not possible to add the third shift until November 14th. From then on, a 3-shift daily schedule was maintained with the exception of holidays and fortnightly change Sundays until August 1st, 1942, when shortage of labour caused the dropping of a shift. All work was suspended on August 14th. The ground through which the tunnel passed was such that the driving was often interrupted by the need of protective timber at the face. Further, crews were continuously employed timbering behind the face, and in maintenance of timbered sections in swelling ground. Roughly 980 feet of the new workings are now timbered, about 21 per cent of the total.

Jan 1, 1942

By Unknown

We are indebted to the Consolidated Mining and Smelting Company of Canada Limited for the several pictures in this issue showing the progress made in new construction at Tadanac and at Bonnington Falls, B.C. Plate No. 1 shows the down-stream side of the No. 1 hydro-electric station of the West Kootenay Power and Light Co. Limited at Bonnington Falls, on the Kootenay river, at which 17,500 k.v.a. will be developed to meet the requirements of the enlarged zinc and lead refineries at Tadanac. The generators, exciters and switch apparatus were supplied by the Canadian General Electric Company and the step-up transformers by the Canadian Westinghouse Company Limited. The plant throughout was designed, manufactured and erected by Canadians. Plate No. 2 shows the casting room of the new lead-plant and plate No. 3 the new tank-room of the electrolytic lead refinery at Tadanac. These additions will increase the capacity of the lead refinery by some 150 tons daily. The extensions also include practically doubling the zinc plant, and the gold and silver refineries. With the exception of the new stack, all designing construction and installation of the various plants is being done by the Company's own employees at Tadanac. Plate No. 4 shows the progress made in the construction of the new reinforced concrete stack at Tadanac. This stack, of 21 feet inside diameter at the top, will be brick lined and when completed will rise 400 feet above its foundations: the tallest of its kind in the world. The construction is in charge of the Rust Engineering Company of Pittsburgh, Pa. Plate No. 5 is a panorama of the Tadanac smelters and refineries. The photograph was taken from the roof of the lead smelter and gives an excellent idea of the size of the plant and its surroundings. Tadanac produces electrolytic lead, zinc and copper and fine gold and silver. During 1924 the company treated 1,333,523 tons of ore and produced: 161,400,- 769 pounds of lead; 92,197,824 pounds of zinc; l,382,750pounds of copper; 4,074,044 ounces of silver, and 26,976 ounces of gold.

Jan 1, 1925

By J. E. Hawley

"The property of Francoeur Gold Mines, Limited, lies directly west of the Armfield mine in Beauchastel township, Abitibi district, and 12 miles west and slightly south of Noranda. The gold deposits are of particular interest because of their replacement character and close association with fault zones. The property was originally staked in 1923 following the discovery oi a mineralized zone near the eastern boundary. This became No. 1 orebody. Later discoveries in 1936 of No. 2 and No. 3 orebodies led to underground development and actual mining in July, 1938. A fourth orebody, No. 8, was found in 1939.The following is the production record up to December 31st, 1947:Beginning in September, 1944, ore was shipped to Noranda as siliceous flux, but late in 1946 milling of low-silica ore from No. 1 orebody was undertaken until operations were temporarily suspended in 1947.The four main ore deposits, Nos. 1, 2, 3, and 8, consist of siliceous ferrocarbonate and albite replacement bodies mineralized with fine pyrite and specularite in schistose fault zones in Keewatin volcanics. Barren to low grade quartz veins though present in some are uncommon, but small stringers of quartz are usually present wherever here and there visible gold is found. Nos. 1, 2, and 3 deposits lie in a major fault zone that extends completely across the property from west to east (over 7,000 feet) and dips N.40° to 50°, and are separated by intervals of 1,800 to 2,000 feet respectively. The fourth lies in a smaller fault zone striking east and dipping on the average 65°S.No. 1 orebody has been explored by mining to a depth of 500 feet, No. 2 to 400 feet, and No. 3 to slightly less than 300 feet . The greater part of No. 8 lies above a depth of 200 feet, but a raise has recently .been driven through from the west end of the 5th level of No. 1 to the 2nd level on No. 8 zone. Most of the ore of No. 8 zone above the 2nd level and of Nos. 2 and 3 above the 3rd levels has been removed."

Jan 1, 1954

"Eastern Canadian thermal coal mined at Minto, New Brunswick, and in western Cape Breton at St. Rose, Inverness County, Nova Scotia, contains 6-8 per cent sulphur. Both coals are high volatile bituminous. types. The Minto coal averages 18 per cent ash, 7 per cent sulphur and has a Btu rating of 11,900 per lb. Pyritic sulphur accounts for 75 per cent of the total sulphur and the remainder is largely organic; the amount of sulphate sulphur is negligible. This means that in a 7 per cent sulphur coal, 2 per cent is organic and 5 per cent pyritic sulphur. Pit-head St. Rose coal contains approximately 10 per cent ash, 7 per cent sulphur and 11 ,800 Btu/lb. The distribution of sulphur is different to that of Minto coal because about 12 per cent sulphate sulphur is present. Thus, a 7 per cent sulphur coal would contain 4 per cent pyritic, 2 per cent organic and 1 per cent sulphate sulphur.The iron sulphides, pyrite and, to a lesser extent, marcassite occur over a wide size range from large sulphur balls to crack fillings, lenses, and individual crystals and framboids. Coarse-grained pyrite and sulphur balls are easily separated during washing. It is the fine grain sizes, intimately mixed with the coal constituents, that are difficult to separate. Quantimet analyses of the fine grains in coal from both localities showed that about 50 per cent were smaller than 30 micron(1).No efforts have been made to wash the Inverness coal of Nova Scotia and in 1980 washing ceased in New Brunswick. Previously, the Minto coal was processed in an antiquated jig circuit which reduced ash from the strip operation run-of-mine value of more than 20 per cent to less than 18. More effective removal of ash and sulphur could clearly be obtained. Laboratory tests on both Minto and St. Rose coal have shown that ash rejection rates of 40 to 50 per cent at yields of 70-80 per cent were possible(2), Little information on sulphur removal was available."

Jan 1, 1981

By S. Flewelling, M. Scobie, G. R. Baiden

"SynopsisA feasibility study to develop a research program, the Mine Automation Plan (MAP), was recently completed. This was undertaken by a team comprised of Inco Ltd., Falconbridge Limited, the Canadian Centre for Automation and Robotics in Mining (CCARM) and the Centre for Resource Studies (CRS). The study was sponsored by PRECARN Associates, which is a consortium of thirty-six Canadian companies focussed on research and development in artificial intelligence and robotics. PRECARN Associates was formed in 1987 when a number of research proposals were funded in the fields of process control systems, robotics systems and intelligent engineering systems. In July 1991, PRECARN accepted the next round of proposals for research. The MAP project was one of the successful proposals, being awarded $100,000 for the development of a feasibility study defining a long-term R&D plan for underground hardrock mining automation.The development of the feasibility study started by addressing the fundamental structure of the mining process, and its relationship to the metallurgical process, over-all infrastructure support and management systems (Fig. I).Mining may be considered as comprising five subprocesses: (I) delineation; (2) development; (3) production; (4) backfilling; and (5) infrastructure support services. Within these subprocesses many applications for artificial intelligence and robotics exist. The mining process is dependent upon the interaction between the physical mining process and information. For example, the delineation process is dependent on geomechanical, geochemical and geophysical techniques to develop a model of the orebody based upon access to such data. This same relationship between the physical and information models holds true through the development, production, backfill and infrastructure support systems.The foundation for the MAP study has been the recent development by Inco Ltd. of an underground communications system (Fig. 2). The system has the ability to supply high bandwidth communications, over voice, data and video to mobile and stationary locations within the mining operation. It is seen to be the future backbone of a comprehensive, automated information system which should permit the application of the concept of Computer Integrated Manufacturing (CIM) to underground mining. CIM, through the automated flow of information, has been successful in integrating the engineering, production and various support groups in manufacturing."

Jan 1, 1994