Search Documents

By J. Cayouette, . Blatter, P. Cousin

The Laronde mill was commissioned in 1988 and has been treating the Laronde Perim ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually. In 2008, the Goldex plant began trucking high wade (35-45 Wt Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold wade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine. Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa)

Jan 1, 2011

By M. Dupuis

In the present study, the heat balance of the Hirakud smelter aluminium reduction cell has been accurately assessed using only a surface thermocouple and a pyrometer, As it is well known that using a single linear or quadratic relationship to estimate the heat flux from the measured surface temperature does not provide the accuracy required to close the cell heat balance, this approach was not used in this study, Instead, the fundamental natural convection and radiation heat flux equations were used systematically for each measurement point, Practically, this means that the ambient air temperature and at least one ambient radiative temperature must also be known in addition to the surface temperature for each measurement point. Sometimes, the radiative heat flux could not be accurately estimated using a single ambient radiative temperature, In those cases, a more accurate estimation based on two ambient radiative temperatures and corresponding view factors has been used instead, It turns out that although at least three temperature measurements are required to estimate a single heat flux, it takes a lot less time to make those temperature measurements using a pyrometer than directly measuring the heat flux using an expensive heat flux meter, Furthermore, no loss in accuracy was detected when using this approach as the cell heat balance could be closed within 5%, the level of accuracy typical of cell heat balance assessment using heat flux meter.

Jan 1, 2004

By Jean-Marc Simard, Richard Genest

"La mine Agnico-Eagle, localisée près de Joutel, a été découverte en 1962 par le forage d'anomalies électromagnétiques. Exploitée à partir de 1974, elle a déjà produit près de 30 tonnes d’or à partir de 2 puits, le puits Eagle et le puits Telbel, distants de 1,3 km.Le gisement est situé entre le sommet du complexe volcanique de Joutel, à dominante felsique, et la base de l'ensemble sédimentaire de la rivière Harricana. Ces deux unités ont une extension régionale; elles sont orientées NW-SE avec une polarité NE et des pendages subverticaux. Une faille majeure, la faille Harricana, passe de façon subconcordante au contact de ces deux ensembles.La minéralisation aurifère, de 2 à 5 m d’épaisseur moyenne, est liée a une zone carbonatée, comprise entre des tufs felsiques, argilites et sédiments chimiques (éponte inferieure) et des argilites carbonatées (éponte supérieure). Le minerai est constitué habituellement de 20% de fine pyrite disséminée. L’or est en fines particules associées directement à ces grains de pyrite de texture cataclastique.Deux modelés ont été for mules jusqu' a présent pour expliquer la genèse du gisement: une thèse syngenetique (Barnett et a/.1982) et une thèse épigénétique (Wyman et al. 1986). Cette dernière apparalt comme la plus probable du fait de la présence de la minéralisation dans les zones cisaillées a carbonates secondaires et pyrite cataclastique."

Jan 1, 1990

By Fred A. Webber

STEEL ROPE WIRE is one of the more specialized commodities among the many grades of highcarbon steel wires. In its production there are many metallurgical aspects of interest from the steelmaking on through the final stages of wire drawing. We produce rope wire in an integrated mill com prising all the operations from the blast furnaces to finished wire drawing in the wire mills. Steelmaking is carried out with close control on hot metal, selection of scrap, and fluxing materials. The basic open hearths are of 170 tons capacity. Steel is teemed into 19 1/2 in by 19 1/2 in big-end-down molds and is hot-topped with the use of clay refractory hot-tops. The weight of this ingot is 6,900 pounds. All high -carbon steel ingots are charged hot into the soaking pits and are then rolled through the blooming mill in 16 p asses to a bloom ax~ in. by 41/2 in. and approximately 65 feet long. Necessary bottom and top crops are taken on the bloom as it passes from the blooming? mill to the billet mill. The still hot bloom is continuously rolled through the billet mill in . 5 passes to a 2 3/8 in. square. Billets are cut to 32 feet in length by a flying shear and then allowed to cool on the hot bed.

Jan 1, 1957

By Li Qihou, Li Yuhu, Liu Zhihong, Liu Zhiyong, Yang Xiaofeng

Scorodite samples were synthesized, in adding or without crystal seed respectively by using Atmospheric Scorodite Process (ASP), Hydrothermal Scorodite Process (HSP), and Improved Atmospheric Scorodite Process (IASP) individually; and their crystal structure, crystallinity, morphology, particle size, specific surface area, Fe/As mole ratio, as well as the leaching stability were characterized, aimed to reveal the relationships among the synthesis methods, the compositional and structural properties, and the leaching stabilities of scorodite. The results show that synthesis methods have significant effects on the compositional and structural properties of scorodite. Scorodite samples of high crystallinity, small specific surface area, and low Fe/As mole ratio, possess high leaching stability. The order in the leaching stability of scorodite samples synthesized in this study is as follow: ASP<HSP<IASP. Scorodite particles in the sample synthesized by IASP without crystal seed are in large sizes and of pyramidal morphology enclosed mainly by crystal planes of {111}; and the sample possesses the crystallinity of 84.5%, the particle size (D50) of 28.2 m, the BET specific surface area of 3.72 m2/g, and the Fe/As mole ratio of 1.05; after leaching this sample by using acetate buffer solution of pH 4.95 for 10 days, the total arsenic concentration in the leaching solution is merely 1.14 mg/L.

Jan 1, 2015

By Norman A. Parlee

Introduction The principal primary iron and steel producing capacity of the Dominion Steel and Coal Corporation is at the Dominion Iron and Steel, Limited, plant at Sydney, Cape Breton Island, Nova Scotia. The main raw materials are Cape Breton coal, Wabana (Newfoundland) iron ore, and Port-au-Port (Newfoundland) limestone. This plant, which was established at the turn of the century has gradually expanded its production facilities so that today its ingot producing capacity is over 720,000 tons annually. Principal operating units of the plant at present are three batteries of 173 Koppers by-product coke ovens with conventional by-product recovery equipment, three blast furnaces .of 15 ft. 6 in., 18 ft. 3 in., and 19 ft. 3 in. hearth diameter (inside the brick), one 700-ton hot metal mixer, ten open hearth furnaces (two of 175-ton capacity, three 12 5-ton, five 60-ton), one 10-ton electric furnace, a 40-inch blooming mill, a billet mill, a rail mill, a tie plate mill, rod and bar mills, and a wire and nail mill. Extensive machine shops and an iron and brass foundry are also available for plant maintenance and repairs. This paper will describe developments during the past five years and those now in process. It will also briefly discuss research being done and indicate the direction of future development.

Jan 1, 1951

By Y. Q. Li, Z. C. Shen, C. H. Zhao

The dynamic properties of the KYF-320 flotation machine which is one of the biggest flotation machines in the world were tested and then verified by the computational fluid dynamics (CFD) simulation. Aeration rate testing results suggest that he effect of circulation holes on the fluid state in the flotation cell becomes gradually smaller when the impeller speed is greater than 107 r/min. The dispersion degree of air increases with the increasing impeller speed and decreases with the increasing aeration rate, and it increases slightly when the impeller speed is greater than 107 r/min. The air holdup increases and then decreases with the increasing impeller speeds and aeration rates, and a maximum value of air holdup is shown at impeller speed of 107 r/min with a value of 12.28%. CFD simulation results are in good agreement with these testing results. Industrial-scale test was carried out using this 320 m3 flotation machine for the flotation of Cu ores. The results show that Cu content increases from 0.06% of crude ore to 1.26% of concentrate, and the S content increases from 0.39% of crude ore to 24.83% of concentrate. Moreover, using this flotation machine 5.88% of power is saved compared to other type of large flotation machine.

Jan 1, 2015

By A. C. A. Howe, J. C. Rowntree

"The Bernie Lake pegmatite near Lac Du Bonnet in southern Manitoba is a complexly zoned pegmatite containing several lithium-bearing units in addition to the western world's largest known reserve of cesium. The pegmatite forms a flat-lying ellipsoidal body within an east-west-trending Precambrian amphibolite. The pegmatite enclosed by this vertically schistose amphibolite lies near the eastern tip of a granitic intrusive. The relationship of this intrusive to the pegmatite is obscured by Bernie lake. To date, the pegmatite body has been delineated aver an area of approximately 80 acres; it attains a maximum thickness of 280 feet. Several distinct zones, including three assemblages of economic importance, comprise the pegmatite itself. The combined spodumene and lepidolite assemblages provide a recoverable defined lithium ore reserve of almost 5 million tons averaging more than 2 per cent lithium oxide. The recoverable cesium ore of the pollucite assemblage provides 300,000 tons averaging more than 20 per cent cesium oxide; this represents more than half of the western world's pollucite reserve. The Bernie Lake pegmatite deposit, owned by Chemalloy Minerals Limited, is well located with respect to the growing United States markets, and its reserves of cesium are large enough to enable it, under favourable economic circumstances, to become the major producer of this metal in North America."

Jan 1, 1967

By W. T. Irvine

Introduction The property of the Britannia Mining and Smelting Company is on the east side of Howe sound, some twenty miles north of-Vancouver. The camp is served by two settlements, one at Britannia Mines townsite, approximately three miles from the water&apos;s edge at an altitude of 2,100 feet, the other at Britannia Beach, on Howe sound. The first discovery of copper ore on the property was made in 1888, but it was not until 1905 that production started. From that year until the end of 1944, production had totalled 732,414,420 pounds of copper and 261,126 ounces of gold from six orebodies, known as the Victoria, Empress, No. 5, Fairview, Bluff, and Jane. No. 8 orebody, with which this paper is concerned, was discovered in 1937 by diamond drilling from the 4100 level, some 300 feet above sea level. Development of this orebody to the end of 1944 had included the sinking of a shaft from the 4000 to the 5250 level, and a limited amount of stoping. This work has delimited the orebody from the 3800 to the 4950 level and has indicated upwards of 1,000,000 tons of copper-zinc-gold ore. It is planned to commence production in the near future, while continuing exploration of the orebody at depth.

Jan 1, 1946

By F. J. Tozer

Canal communication between Lake Erie and Lake Ontario has been one of almost constant enlargement and reconstruction to meet the rapid growth of trade and commerce, and the consequent steady increase in the size of vessels plying the Great Lakes. The original canal was built by the Welland Canal Company. The first sod was turned in 1824 and the first vessel passed through in. 1829. There were 36 lift-locks, built of oak timber, 110 feet long and 22 feet wide, with a depth of water over the sills of 8 feet. The second canal, now known as the &apos;Old Welland Canal&apos; was built by the Dominion of Canada (1842 to 1850). There were 26 masonry locks, 150 feet long, 26.5 feet wide and with a depth of water over the sills of 9 feet. The walls and banks were raised in 1853 to give a 10-foot draught. The third canal, known as the &apos;New Welland Canal, built by the Dominion of Canada, was started in June 1874 and the first boat passed through in the spring of 1882. There are 25 masonry lift-locks, 270 feet long, 45 feet wide and with a depth of water over the sills of 12 feet. The walls and banks were raised in 1891 to give a 14-foot draught. This is the canal in use at present.

Jan 1, 1926

By J. Chao, C. Tan, N. Stubina

"Since J978, Falconbridge Limited has operated two electric furnaces at its nickel-copper smelter in Sudbury. As part of its S02 Abatement Program, the smelter has undergone many changes over the last seven years.This paper describes the impact of these changes on the operation of the furnaces. Some of the topics to be covered include: the installation of sidewall copper coolers; current operating conditions; and furnace heat and mass balances. HistoricalFalconbridge began smelting ores in the Sudbury area in 1930. The original smelter consisted of a 1.3 m by 3 m blast furnace and two 4 m by 6 m converters. The blast furnace was supplied with untreated mine are and molten slag/matte was discharged into a round settler.In 1933 the smelter began treating flotation concentrates. The concentrates were mixed with fine magnetic ore and flue dust, then sintered on down-draught Dwight Lloyd machines. This provided an agglomerate suitable for furnace burden which was charged to the blast furnace while still hot.Between 1930 and 1954 nickel production was increased by lengthening the 3 m furnace to 4.6 m, then to 6 m, and later by constructing additional furnaces. By 1958, the plant consisted of one 7.5 m blast furnace, a settler, and three 4 m by 9 m converters."

Jan 1, 1994

By F. P. Yungwirth

"IntroductionTrout Lake Mine is located about 5 km north of the Hudson Bay Mining and Smelting Co., Limited complex at Flin Flon, Manitoba. The mine was brought into production in 1982at the onset of a severe recession in the base metal market. The mine is operated as a joint venture with HBM&S, MMR and SMS.During the first several months of operation it became evident that there were opportunities to reduce costs at the mine significantly, and a productivity improvement subcommittee was formed to make recommendations. The first committee met in January, 1983 and consisted of the mine manager from Hudson Bay Mining, a geological expert and a maintenance expert from Outokumpu Oy, Finland, and a mine manager from Granges, Sweden.Recommendations from this committee were implemented during 1983 and a new subcommittee was constituted in 1984 to continue the work begun the previous year. The committee remains as constituted in 1984 and meets quarterly.The committee consists of M.A . Kirby , manager - Flin Flon Mines, HBM&S; Gustav Hoberstorfer of Mindelco , a Swedish mining consultant retained by Granges; Eero Laatio, mine superintendent of Keretti Mine at Outokumpu Oy in Finland; and Bob Bray, a mining consultant retained by Manitoba Mineral Resources.Many productivity improvements made in the operation are attributed to the work of this committee and other experts retained at various times throughout the mine life."

Jan 1, 1988

By D. J. MacDonald

UNDERGROUND development at the Lynn Lake property of Sherritt Gordon Mines, Limited, was begun in 1948 with the sinking of the A shaft in the area of the A orebody. By June, 1949, the shaft was completed to a depth of 1,024 feet. Twelve stations were cut, with the bottom level at 992 feet below the collar. Since completion of the shaft, lateral work has been carried out on the 12th level in order to expose the known orebodies and to provide openings from which deeper exploration could be conducted. Dur¬ing the change-over from sinking to lateral work, preliminary diamond drilling was done from the 12th level station to locate the A? ore-body. Later, drilling was carried out from the 5th and 9th level sta-tions, where, also, the outline of the A orebody was established. As the work progressed on the 12th level, and with the commence-ment of drilling below that level, the geological picture was found to be complicated by numerous faults. Instead of operating two drills it became necessary to use at least four. The original plans had provided air sufficient to drive two headings and to operate two diamond drills. The addition of two more air-driven drills resulted in a serious shortage of power.

Jan 1, 1951

By V. Bruned, K. Mohamed, A. Michaut

Orano Mining Somaïr uranium treatment plant (Niger) uses a pugging-curing process to leach uranium. Sulfuric acid, nitrates and water are added to the finely grinded ore in a rotary drum to leach uranium bearing minerals and solubilize uranyl sulfate ions. Reagents, sulfuric acid and nitrates, are the main OpEx of this process step. The economical optimization of their addition requires a thorough knowledge of the ore behavior in solution with these reagents. Orano Mining technical direction and Somaïr laboratories developed a model to predict the curing process uranium recovery surface with a limited number of parameters. Experimental laboratory work to fit the model needs to be done for each type of ore which can require a lot of metallurgical tests and would be time consuming. In order to optimize the required number of tests, an innovative experience plan was designed in parallel to the development of this model reducing the required number of tests to only eight. Once the parameters of the models are correctly fit, the comparison between the estimated values and the actual values for the uranium recovery is excellent (less than 0.5% error in average). Associated with an updated cost model of the curing process, this new recovery model helps the plant operator find the best set of reagents to maximize curing process profitability in the Somaïr plant day after day.

Jan 1, 2020

By Alfred C. Lane

Reference to the original use of the terms Laurentian and Huronian (and its extension), shows that the former was applied to granitized sedimentary and metamorphic pre-Cambrian rocks, and the gneissoid igneous rocks associated therewith, and the latter to non-fossiliferous rocks supposed to be later. But it appears from the work of Collins, Quirke and others that there is more or less of an overlap, and that of the original Laurentian the Grenville limestone, and some of the granites, may be later than the lowest part of the original Huronian. Before we can decide whether to abandon one or the other of the two terms, or how to delimit them, it is important to know the extent of this overlap. The Pb :U ratio, though not to be depended upon too minutely, does give a real idea of the age of a mineral as it increases with the decay of uranium, and so is greater the longer the time since the uranium was separated: and there are reasonable prospects of help there from in getting a knowledge of the relative age of different granites to assist in solving the problem, as facts already collected show. 1. Historical review of the use of the words Laurentian and Huronian: 2. Difficulty encountered: 3. Popular account of atomic disintegration: 4. Methods of estimating age by it: 5. Applications.

Jan 1, 1925

By Roy T. Bowles

This paper focusses on technological developments which occurred in the village of Deloro, Ontario between 1868 and 1919. These developments illustrate the manner in which improved metallurgical processes linked Ontario mineral resources to industrial expansion. Overview of Deloro The village of Deloro is in Hastings county, about 5 miles from the village of Marmora, the site of the old Marmora iron works and the more recent Marmoraton iron mine. In this area, the Canadian Shield meets the Great Lakes lowlands. The first settlement in the vicinity occurred in the 1820s and was associated with the Marmora iron works. Settlement grew around agriculture. Gold was discovered in Hastings county in 1868. Deloro - the name derives from gold - developed as a concentrated settlement in proximity to several gold mines and the related processing activities. By 1901, substantial smelting works were successfully producing gold and arsenic from local ores. The village was developing as a company town within the framework of benevolent paternalism. For reasons associated with markets and with local ore supplies, the Deloro mills were idle for a period beginning in 1902. Developments in later periods connected Deloro to world events. In 1903, silver was discovered at Cobalt, Ontario. By 1907, M.J. O&apos;Brien, who owned mines at Cobalt, had purchased the Deloro works and was using them to process Cobalt-area ores*.

Jan 1, 1999

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

By R. H. Beaton

"About 1905, a plant was constructed at C1ayburn, in the Lower Fraser valley, 4'5 miles east of Vancouver, to process shales from Sumas mountain into heavy clay products. In time, mining operations were found to be more favourable on the opposite side of the mountain, and by 1913 a plant, which soon became the centre of activities, was completed at Kilgard. Destroyed by fire in 1949, the plant was rebuilt on modern lines, and a second plant was established at Abbotsford, six miles to the west. The Company, from its beginning, has grown with development of the Province. In recent years, operations have kept abreast of latest developments, particularly in materials handling. Latest innovation has been the complete conversion of fuel from Bunker C oil to natural gas. In 1957 the Company became associated with Harbison Walker Refractories, Limited, a leader in its field in the United States, and its title was changed from Clayburn Company, Limited, to Clayburn-Harbison, Limited. Currently, the Kilgard plant produces sewer pipe, agricultural tile, and flue liner; the Abbotsford plant, refractories and facebrick. Improvement of products and development of new ones are tasks of a recently-completed testing and research laboratory.Almost all ware produced is marketed in Western Canada or Washing-ton State. The Vancouver area absorbs the bulk of structural clay products."

Jan 1, 1959

By Gino Palarchio

Dofasco is Canada?s 2nd largest steel manufacturer producing 4.5 million tons of flat rolled steel per year. They have revenues of over $3 billion and employ 7,000 people in their Hamilton, ON plant. Dofasco is North America?s most profitable steel producer and were recently ranked as the #1 steel maker in the world by Dow Jones. Motivation to Improve In the 1980?s the steel business was good. However, in the late 80?s and early 90?s things began to change. Globalization was beginning to influence the market, imports started arriving at lower prices and higher quality, hangover from the 1970?s inflation saw costs rising and prices dropping, there was a shift from a sellers to a buyers market, and shareholder returns were beginning to erode. Dofasco took a step back and evaluated their maintenance performance and found that they were operating in an environment where 70% of their work was reactive and only 30% was proactive. They also found that the rate of product quality improvement was flat and their average equipment availability was only 78%. At that point they realized that Equipment Reliability was key to improving product quality, production output, costs and shareholder return. They initiated a project to research, develop, and implement the most advanced maintenance practices and information technologies to achieve maximum equipment reliability.

May 1, 2001

By X. Cao, X. -G. Chen, K. Liu

Due to the detrimental effect of platelet iron-rich intermetallics on mechanical properties (particularly ductility) in cast alloys, it has been essential to transform these phases into Chinese script morphology. In the present work, the effects of Mn and/or Si addition and cooling rate on the phase transformation of the iron-rich intermetallics in 206 cast alloys with different Fe contents ranging from 0.15 % to 0.5 % were systematically investigated. The results obtained showed that platelet ß-Fe and Al3(FeMn), Chinese script a-Fe, Alm(FeMn) and Al6(FeMn) can be observed in the 206 cast alloys, depending on the Fe, Mn and Si contents as well as the cooling rate. It was found that the addition of either Mn or Si favors the formation of Chinese script iron-rich intermetallics but inhibits the precipitation of the platelet phases. In addition, the combined addition of both Mn and Si has a synergistic effect on the phase transformation. Furthermore, there exists a critical cooling rate to effectively suppress the formation of platelet iron-rich intermetallics for a given alloy. The threshold cooling rate decreases with increasing Fe, Mn and Si contents. Casting process maps are established to correlate the intermetallics precipitated with alloy chemistry and cooling rate for 206 cast alloys containing various Fe levels.

Jan 1, 2014