Search Documents

The flolation behaviour of some Australian uranium ores was investigated. Although uraninite and pitchblend float readily with fatty acids, selective concentration to produce an economically discardable tailing has not yet been achieved. This is attributed to the presence in the ores of a quantity of uranium mineral in finely dispersed form which is very difficult to liberate. For some of the ores, at least, the proportion of this material decreases with increase in head assay.Flotation may be a useful concentrating method for some Australian ores if uranium oxide is to be sold in a free competitive market.

Jan 1, 1967

Notwithstanding full concurrence with the dictum of a famous scientist that "definitions are the most accursed of all things on the face of the earth," in view of the considerable confusion which exists in jigging nomenclature, it is considered advisable to commence this paper with the following explanations of the terms which will be used throughout the text.Jig Bed. The whole layer of material lying on top of the jig screen.Ragging. The layer of denser material lying immediately above the jig screen, which is too coarse to pass through this screen and is confined horizontally by the cells of the top grid.Ore Column. The layer of ore pulp between the ragging and the top-water.Top Water. The water, carrying fine material in suspension, which flOiWS over the surface of the jig bed.Hutch Water. The water added to the jig below the screen. (Except for the water discharged with the hutch concentrate, the "hutch-water" eventually becomes "top-water.")Feed Water. The water in the ore pulp fed to the jig.(This water becomes part of the "top-water.")Pulsion. The period of the jigging cycle during which the water is moving upwards relative to the particles in the jig bed.

Jan 1, 1937

By W Farnworth

The Huntly West Mine has undergone significant changes in the last two years, which will affect the remainder of the mine's life. The paper describes the evolvement of plans and an overview of the technical considerations made in planning for and implementing the first New Zealand longwall operation. The technical investigations involve the longwall equipment, exploration, ventilation and strata control. The focus on these areas was to ensure that unacceptable project risks were addressed. Implementation of longwall mining at West Mine is planned in three phases, Development, Panel One extraction trial, and Full Longwall operation.   At present the development phase is complete, longwall installation is in progress and production start-up is planned for the end of August, 1991.

Jan 1, 1991

This paper presents the near-field rock damage owing to production blasting in limestone quarry in the western region of Japan. The study's purpose is to learn the mechanism of crack development due to blast vibration. In this study, blast vibration's magnitude was expressed with peak particle velocity (PPV) which was obtained based on seismographs recorded database. In attempt to pursue a research's purpose of this study, there were two considerable interests: near-field blast vibration propagation and prediction, and crack observed and prediction. Furthermore, with regards to considerable interest of the study, there were three essential aspects which were challenged, such as: monitoring and interpretation of seismic wave propagation in a rock mass near large explosive charge of production blast scale, measurement of blast rock damage in adjacent to blasthole, and determine critical value of PPV which may produce significant rock damage. In order to determine precision critical PPV, understanding correlation between rock damage with vibration level is firstly important to be done. This paper also discusses how to measure, detect and quantify near-field blast vibration and blast rock damage in adjacent to blasthole.

Dec 6, 2010

By Sharpin P. C

The countercurrent gas-solid heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temperature distributions through the drier have been calculated. Although the calculations rest on several simplifying assumptions, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating conditions on the rate of drying of the briquettes which controls the strength of the char produced. The analysis shows why a limitation was reached in the improvement of char strength in the pilot plant in 1961 due to the performance of the drier and a prediction is made of a way in which the limitation could be overcome.

Jan 1, 1966

A genesis based on new developments in the physical chemistry and flow properties of colloidal substances is proposed for the pipe-like Peko orebody. The rheological behaviour of sediments is governed by the contained colloids. Remobilization of thick pasty sediment during diagenesis is regarded as an essential step in the concentration of metal dispersed in sediments. At a high concentration the sediment pore fluid is a dense gelloid such that van der Waals attractive forces between the colloidal particles exceeds the coulombic repulsion. This permits accretion of the colloids into globular clots and their fracture fragments. These have a uniform size distribution dependent upon the rate of shear, and the sediment lithifies to clotted, porphyry-like, "gritty", dolomitic or igneous-looking intrusions and flows. The physical chemical properties of natural sediment colloids appear adequate to account for ore formation.Adsorption accounts for the dispersion and retention of metal in sediments. Accretion accounts for the segregation of the colloidal materials to give the various types of clotted igneous-looking intrusive source rocks. Syneresis enables the colloids to spontaneously draw together and to dehydrate. Formation of an ordered lattice achieves a lower energy state and desorbs metals and insoluble metal compounds "particle by particle" into the escaping water of hydration and pore water. Peptization enables migration of the metal hydrosols as stable dispersions until they merge for outflow through seepage zones or water extrusion channels. Nucleation and concretion precipitate the metal dispersoids from pore waters seeping through hydrous parts of the source rock, porous beds, faults, and zones of weakness by which the connate waters leave the lithifying sediments. Gelatinous precipitated mineral matter in the ore channels is capable of thixotropic reliquefaction when disturbed by shock or movement. Local reintrusion, flowage, interveinings,brecciation, and intermixing of the materials is the result.The principles of the suggested genesis are applicable to both syngenetic and epigenetic mineral accumulations.

Jan 1, 1966

By D J. Corp

The Halmahera Contract of Work is a sixth generation contract held 82.5 per cent by Newcrest Mining Limited and 17.5 per cent by PT Aneka Tambang and takes in the Gosowong Project area. In 1991 Newcrest Mining Limited established a small exploration office in Jakarta and proceeded to seek exploration opportunities. The Halmahera area was identified as a substantial prospective ground position in a relatively unexplored area. In late-1991 Newcrest Mining Limited and PT Aneka Tambang agreed to explore in Halmahera. Initial field work commenced in July 1992. A vigorous ground reconnaissance programme led to the discovery of the Gosowong deposit a little over 12 months later in September 1993. In April 1997 the Contract of Work was approved covering much of the island of Halmahera. Between September 1997 and November 1998 activities were directed principally towards obtaining the necessary permits required to commence construction activities. Some particularly ambitious targets were set for achieving this outcome. An aggressive construction programme commenced in late-1998. Construction took place during a period of unseasonally high rainfall, which in itself presented additional challenges to the construction team. A key milestone for the project was achieved on 1 July 1999 when wet commissioning of the process plant commenced. Construction of the Gosowong Mine was achieved on time and within budget. A period of some six years elapsed from the initial discovery of the Gosowong deposit to the time of the first gold pour. Much of the permitting, construction and commissioning activity took place between September 1997 and July 1999. This coincided with a period of significant social, economic and political upheaval in Indonesia. During the construction period a high level of importance was placed on the structured recruitment and training of local people, as well as fostering appropriate community and local business development programmes in the communities nearby the project. Emphasis was also placed on environmental management with detailed long-term planning and progressive rehabilitation commencing during the construction phase. The permitting and subsequent development of the Gosowong Project has demonstrated that even during the difficult times, with commitment, it is possible for mining and exploration companies to conduct business in Indonesia.

Jan 1, 1999

By Whiten W. J

An investigation on the breakage characteristics of closely sized orc samples at different levels of input energy was carried out to determine an appearance function for possible use in ball mill modelling. A consistent pattern of breakage behaviour was observed and the resultant size distributions could be described by a one-parameter, ('t'), family of curves. For each particle size range tested, this parameter 't' has an exponential relationship with input energy below an upper energy limit. A tentative linear relationship between the input energy at a constant value of 't' and the work-index leads to reconstruction of 'I' - input-energy curves from the work-index values. To normalise the efrect of particle size and input energy, multidimensional cubic spline regression was performed on thc entire range of data. The results indicated that the parameter 't' can be determined, reasonably accurately, as a function of Ln (input energy, kWh/tonne) and Ln (particle size, mm) for input energies between 0.5 and 8.0 kWh/tonne.

Jan 1, 1983

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J Wei, A Yo, R Levy

Waste water reuse from municipal and industrial effluents is becoming increasingly important in many areas around the world. Water scarcity, local regulation and environmental impact are driving many industries like coal and copper mines to reuse the large volume of waste water they produce. For example, the Chinese coal industry generated about 4.2 billion tons of mine waste water in 2005 of which only approximately 30 per cent was reused. Coal energy represents 76.6 per cent of the total energy generated in China in 2007 and most of the coal-fired power plants are located in north-west of China, which is a water stressed area.The selection of mine waste water treatment process is challenging as the effluents typically contains high levels of organic compounds and salinity and their composition can vary significantly. In recent years there has been a growing interest in the integration of ultrafiltration (UF) and reverse osmosis (RO) membrane technologies for mine waste water treatment and reuse.In this paper, an overview of the design and performance of ultrafiltration and RO membranes applied for reuse of mine waste water are discussed. A study was carried out in two effluents treatment plants treating copper and coal mine waste water, which are located in Chile and China respectively. The following topics will be discussed to demonstrate the performance of an integrated membrane system in mine waste water reuse: The main challenges from copper mine waste water treatment: high level of chemical oxygen demand (COD); high level of total suspended solids (TSS); high salinity; high concentration of silica, sulfate, iron and other contaminants; and fluctuation of raw water quality. The main challenges from coal mine waste water treatment: high level of total dissolved solids, and waste water quality fluctuation. Design parameters for waste water treatment systems: Selection of pretreatment for dual-membrane system in the copper mine: Clarifier with coagulation and flocculation to remove high TSS; Dissolved Air Flotation (DAF) to remove non-settling solids; Media filtration to handle fine solids and particulate organics; Activated Carbon filters (ACF) to remove dissolved organics, colour and odours. Selection of UF and RO membranes and specific design of their recovery, flux, chemical dosage and cleaning regimes. Finally, the performance of UF and RO, including the main fouling factors and efficient cleaning procedures, will be presented and compared to the design parameters to demonstrate the efficiency and performance of the selected integrated membrane systems in each case.

Jan 1, 2009

By L McCracken

Up until 1990 CoalCorp North Island's accident record was six times that considered acceptable in those NSW operations with good accident prevention programmes. This was an obvious avoidable burden on the company in both human and cost terms.   Late in 1989 an accident prevention programme was implemented with the objective of achieving a 50 per cent reduction in the lost time accident frequency rate within 12 months. The key to achieving this objective was recognised as being an attitude change in the total workforce from General Manager downward. Management commitment and action were seen to be critical to the success of the programme.   Through very basic and simple training programmes in accident investigation, analysis and reporting, communication, on-the-job coaching and in focusing on improving supervision skills, the original objective was achieved.   During 1991 the application of methods improvement and hazard recognition techniques are seen as the logical step to achieving a further 50 per cent reduction in the accident frequency rate.

Jan 1, 1991

A Good Product Range - So What! While in terms of water, waste management and environment protectrion, the Gippsland Basin may appear to have a good product range, what does this really mean? What it means is that, like any product range, the virtues of the product range must be sold and accepted by a majority of the public. The social, economic and environmental benefits of any enterprise using these products must be sold and accepted by the regional population. Many a budding entrepreneur has failed because he assumed that the public would accept his product, so good did it appear to be! However, we know that such an assumption must be avoided and that a great deal of time and effort needs to be invested in promoting and gaining acceptance of a product to ensure a long term and viable market.

Jan 1, 1992

Concentrations of bright green material in the "Golden Mile" of Kalgoorlie, which carry particularly high gold values, are known locally as "green leader".This assemblage consists largely of quartz, sericitic muscovite, carbonates, and pyrite. Some of the sericitic muscovite contains vanadium, giving the rock its green colour. Vanadium oxides, including nolanite, are also present. Tellurides identified in this study are calaverite, altaite, petzite, melonite, and coloradoite. Native gold was found in most of the samples; some of the gold, at least, has been formed from the decomposition of gold tellurides.It is suggested that mineralizing solutions carrying gold and tellurium leached vanadium from the host rocks and subsequently deposited gold tellurides and vanadium-bearing minerals in the "green leader".

Jan 1, 1977

Recent developments in diamond drilling practice have been chiefly 'concerned with modifications in drill design and 'operating technique whereby an increase in daily footage rates and reduced footage costs have been achieved without any marked improvements in the recovery of core. This trend is perhaps due to the general acceptance by the mining and drilling engineer alike of the belief that diamond drilling has definite limitations in exploratory work on mineral deposits characterized by irregularities in continuity and grade, such a belief arising from the fact that drilling technique has not yet evolved coring devices to ensure the full recovery of the rock and mineral formations penetrated.Current diamond drilling operations at Moonta and Wallaroo Mines, carried out by the South Australian Department of Mines, have attained remarkable results in completely eliminating core-loss by the use of a special double-tube core barreI.It is considered that assays of borehole samples taken with this special barrel have a reliability comparable, if not superior to that of similarly situated mine samples and, provided they are spaced satisfactorily, can be used as, a basis for calculating tonnage and grade. Formerly, with only partial core-recoveries, positive borehole results on narrow irregular lodes, such as those in the Moonta and Wallaroo Mines, could be accepted mainly as indications of the presence of mineralization, and could have only a limited bearing on estimates of ore reserves.The value of this special double-tube core-barrel lies In the fact that it guarantees good core recovery and, therefore, good samples, and eliminates the need for sludge-sampling, which is prone to give unreliable assay results from several causes, such as gravity concentration in the bottom of the hole and return water losses which cannot be overcome.In view of the increasing demand for minerals and the probability that the search for them will be carried on largely by boring, it is felt that it would be of interest and value to direct the attention of mining engineers to core-recovery results obtained by diamond drilling plants in South Australia and the features of the special core-barrel, designed by the writer, which has made this possible. Also, the writer is desirous of placing on record two other core-recovery devices designed to extract accurate samples in relatively soft or unconsolidated formations. The latter are used with percussion and calyx plants, respectively and their value has been proven on phosphate rock and coal deposits in South Australia.

Jan 1, 1943

By D Craw, J Becker

Post-metamorphic structural evolution of Otago Schist resulted in a pattern of northwest and northeast striking faults and fractures cutting the basement rocks. These faults have been reactivated several times since Mesozoic metamorphism. Gold-bearing quartz veins which have been exploited sporadically over the past 130 years are almost invariably hosted by northwest striking structures, and most exploration has been focussed on these structures. There is evidence for hydrothermal activity and mineralisation along some of the northeast striking structures, although there has been very little work done on these structures. Our study is attempting to characterise the hydrothermal processes in the northeast structures, in comparison to the northwest structures, in order to see if further detailed exploration is warranted. There is evidence for both normal and reverse senses of movement on northeast striking faults, and some of the faults have evidence for early ductile deformation overprinted by later brittle structures. Northeast striking structures host stibnite mineralisation in places, and faults are locally silicified or extensively impregnated with ankeritic carbonate. Sulphides are rare in veins, but do occur in some hydrothermally altered host rocks. Hydrothermal haematite accompanies extensive silicification along the Manuherikia fault zone near Alexandra. Anomalous gold concentrations occur in some hydrothennal zones, and in downslope sediments in some localities.

Jan 1, 1998

This paper gives a description of the methods of mining employed at North Broken Hill Limited, Broken Hill, N.S.W.GEOLOGICAL NOTESThe main Broken Hill lode occurs as a replacement of tightly folded pre-Cambrian sediments. Replacement has followed certain stratigraphical horizons and the main bulk of the ore is found where these have been packed into the noses of anticlinal and synclinal folds.Throughout the mine the ore-bearing folds pitch north fairly consistently at 45 degrees, as a result of which two favourable horizons in the same fold appear in plan as separate orebodies and these are referred to as the "Southern Orebody" and the "Northern Orebody" respectively.The general dip of the orebodies to the west is about 60 degrees. A typical sill is shown in the plan of the 1,400-ft level (Fig. 1).Both the hanging wall and footwall rocks throughout the mine are weak and, as a result, it is necessary that the hanging wall must be well supported after ore extraction, to prevent subsidence. The weakness in the footwall is confined to a narrow zone, approximately 60 feet in width. This weaknes.q is a source of trouble in the development headings which pass through it, It is sufficiently crushed to transmit weight from the overlying wall to the gangways below.Another feature causing ground instability is the presence of many faults. Although their effect on the shape and character of the orebody is relatively small their...

Jan 1, 1940

This paper describes a proposal to reopen the Sylvia gold mine for underground exploration and development for an initial production of 10 000 tpa. A combination of trackless mining equipment and railtrack would be utilised for development with ore extraction being carried out by undercut and fill methods. The use of the smallest LHD units for mucking, and rail track for the main haulage together with airleg drilling will form the basis for development and stoping. The proposal has been subjected to an environmental impact assessment report to evaluate the impacts of the proposal on the natural and social environment in the area.

Jan 1, 1987

Draft tube circulators are now widely used instead of Pachucas for suspension of slurries in large tall tanks.Precipitators in the alumina industry are an example.Draft tube/tank diameter ratio is critical. Two independent criteria are given for optimum ratio. The hydraulic and energy relationships are defined. These require an impeller of very high specific speed. For a stable and efficient system the impeller should have aerofoil blades with a pitch angle which decreases from hub to tip.The draft tube must be matched to the impeller with inlet baffles above the impeller and flow control vanes below it. Tip recirculation must be suppressed. The tank itself should have a filleted flat bottom.Such a system exhibits the behaviour of axial flow devices with the characteristic undesirable behaviour at low flow.Installed and operating power requirements depend critically on hydraulic design and to a lesser extent on speed reducer efficiency.The problems of re-suspension have been overcome by a patented slot system which also improves behaviour at low flow to permit a more economic design. A number of other practical operating considerations are also discussed.

Jan 1, 1982

An integrated palynological and sedimentological investigation of four wells from the eastern margin of the Gippsland Basin has resulted in a scheme for classification of palynofacies in this area. Thirteen different palynofacies assemblages are recognised and assigned to particular environments based on the enclosing sediments, which range from alluvial, through coastal barrier to continental shelf environments. Close correlation is observed between the interpreted energy regime of the palynofacies assemblage, and that of the enclosing sediments. Assemblages characterised as reworking surfaces can be correlated with unconformity producing events (ie tectonic activity associated with the opening of the Tasman Sea), and some of the minor eustatic sea level Changes.

Jan 1, 1992

As we look back through the Proceedings of our Institute, we find few papers dealing directly with education and recruitment. Apart from papers prepared in the earlier decades of this century, there was little written discussion on the subject until the 1950s, and mostly this was by the professionals, the professors and lecturers who staff the various mining schools of Australia and New Zealand.I use the term "mining school" in its fullest and widest meaning, to cover all aspects from ore to metal, and not in the narrow meaning that the word might imply. At the same time, in restricting the parameters of this address to "ore to metal" I recognize that I am excluding the very important fields of physical metallurgy and materials science; this I do because there is a limit to the quantum of any paper, and in fact these subjects are more closely allied to the use rather than the production of metals.However, the lack of education papers does not mean that education has been regarded lightly by The Institute. Sir Maurice Mawby in his presidential address in 1968, reminded us of the original objectives of The Institute, one 'of which was, "To promote the arts and sciences connected with the economical production of the useful minerals and metals ...". Our present Royal Charter is more specific when it says that one of the objects of The Institute is, ". . . to encourage the study of engineering with special reference to mining and metallurgy ...". If we recognize that in itself membership of our Institute is one means of continuing our education, it is true that education has been a concern of The Institute since it was first founded.Occasionally in recent years, an intrepid president has ventured to tell the academics what the industry needs, and he generally does this in a "no-question" situation! However it is encouraging that those entrusted with mineral education have always accepted this; they keep coming back for more and ask us to tell them what we want, and they will provide it.In 1948 a considerable dialogue on education was initiated when a standing committee was established by the Council of The Institute. In the period 1949 to 1951, three papers were prepared under the chair...

Jan 1, 1974