Search Documents

Coal is of tremendous importance for the Czechoslovak econ- omy. The current annual primary energy demand being about 109 million tons of standard fuel (1 ton of standard fuel - 7,000 coal = 29,308 GJ), coal satisfies almost two thirds of our fuel consumption. If compared with the distribution of resources in the world's fuel and energy pattern, the situation in Czechos- lovakia is significantly different, as shown in Fig. I. One of the causes behind the difference is that the Czechoslo- vak oil and natural gas reserves and, hence, their production are insignificant, so that it is necessary to import them. Brown coal will continue to play an important role as a prin- cipal domestic source of primary energy even in the future. While the share of nuclear power is increasing, brown coal represents strategic reserves in the fuel and energy balance.

Jan 1, 1989

By A Weston

Northparkes Mines is a joint venture between Rio Tinto and the Sumitomo group and is operated by Rio Tinto to produce copper concentrate from ore sourced from open cut and underground. Underground ore is mined with an owner operator workforce using the block cave method from the E26 deposit, with the first lift of the cave now completed. Development of the Lift 2 block cave commenced in March 2001 using a contract workforce. The Lift 2 Project required the mining of 14 700 m of decline and lateral development to establish a new mining horizon at the 9450 level and to develop two new conveyor declines. Also included in the scope was the excavation of a Crusher chamber to house the jaw-gyratory crusher. This paper describes the excavation of the hydroset chamber and orepass that sit immediately underneath the Lift 2 Crusher chamber. It includes risk assessment, planning, development of method statements and standard operating procedures, through to the excavation of the orepass and the installation of ground support in seismically active ground. There was a major ground failure in the backs of the conveyor feeder chamber during its excavation, which affected the excavation of the orepass due to its proximity to the breakthrough site.

Jan 1, 2005

It is hypothesised that increasing the number of loading passes will produce a reduced range of truck payload outcomes compared with four-pass loading. The paper provides analysis to support this hypothesis. It is shown that, hypothetically, loading trucks with five or more passes will result in reduced tendency for overloading and reduced confidence interval for truck payloads that increase the confidence level of containing high end payloads within safe and commercially acceptable limits. Furthermore, increased number of passes provides for more precise bucket load spotting and so improves distribution of payloads within truck bodies. Truck-loading issues examined by the paper include: Improvement in life of driveline components and tyres. Generally tyre costs are relatively moderate; but tyres tend to become an increasingly sensitive performance/cost component as truck scale increases; Reduction of site severity fects flowing on to suspensions, truck frames and structural components generally with potential for reduced long-term repair costs; Less physical body damage due to smaller load increments; Reduced risk of non-compliance with payload limitations for safe braking standards; Increase in loading cycle times tend to increase with scale of loading machinery within the limits of a specific type of equipment (ie rope shovels or hydraulic shovels). Production increase with increased bucket capacity is, to a degree, offset by slower loading cycle times. This is particularly pronounced with front-end loaders but tends to be less noticeable with hydraulic excavators/shovels and electric rope shovels. Decrease in loading time, as a proportion of total truck-cycle time as open pits deepen and dump reaches increase. The production and cost benefits of four-pass loading tend to diminish as truck cycle times increase. The paper also discusses the implications for loading-equipment philosophy to satisfy the future needs of the industry. Cost benefits from upscaling tend to diminish as truck scale increases, so increasing management diligence and close monitoring are required to ensure that expected outcomes are realised. These truck-loading issues have been researched to assess the benefits positive or negative) of four-pass loading in practical scenarios. An attempt is made to determine whether four-pass loading is a æmust-haveÆ or merely a æmythÆ.

Jan 1, 2003

By T C. McCuaig, D B. Mapleson

The Wannaway Deposit is a structurally modified komatiite-hosted nickel-sulfide deposit. Until recently, nickel sulfide accumulations surrounding the Widgiemooltha Dome had been studied with a focus on understanding volcanological aspects of komatiite flow regimes and nickel-sulfide accumulation. Although volcanological features can be observed at Wannaway they are overprinted by several generations of structures associated with multi-phase deformation of the Dome. On the mine scale, two significant deformational events can be distinguished that control ore distribution. The first deformational event is represented by the formation of a layer parallel foliation within the footwall metabasalt and boudinaging of the ore into two distinct orebodies (mega boudins) during a north-south compressional event. Evidence of a second compressional event (east-northeast-south-southwest) is defined by reverse > dextral thrust-folding of the ore zone. The latter deformational event focussed the sulfide ore into thrust front positions where folded ore sequences are mined with stope widths up to nine metres wide. Later stage compressional and extensional deformation phases are observed but have minor, localised effects on the geometry of the ore zone. Four orders of control on the geometry and distribution of ore are interpreted through a combination of primary and secondary features observed at Wannaway. Extending the structural aspects of the secondary overprint features into areas of potential mineralisation has not only defined targets for extensions to the Wannaway Deposit, but has also aided to delineate high grade mineralisation and aid mining decisions. Obtaining an understanding of the volcanological conditions of formation, and more importantly, the structural evolution of the Wannaway region has been an integral part in optimising production.

Jan 1, 2003

By S C. Dominy

The Bendigo Goldfield is located in the state of Victoria, Australia, and is one of a number of quartz-reef fields that make up the greater Central Victorian Goldfield. At Bendigo gold particles are characterised by their very coarse nature, ranging from below 100 to over 10 000 ¦m in size. Some 60 per cent of the gold occurs in particles greater than 1000 ¦m in size. This characteristic ensures that the mineralisation is very challenging to both sample and evaluate. Diamond drilling provides a measure of geological structure, but is a poor measure of in situ grade, understating it by up to 75 per cent. Drilling combined with on-reef development, bulk sampling and geological interpretation has been used to define Indicated Mineral Resources. For grade control, a balance had to be sought between sample representivity, cost, turn around time and practicality. Sampling of extreme nugget effect deposits generally requires the use of bulk sampling in order to be representative. However, the cost and turn around time is significant. As a result, a 50 kg micro-bulk sampling system has been introduced that attempts to overcome these problems by providing a fast, practical method that can discriminate between ore and waste. As the mine passes into production, grade control will increasingly become dependent upon geological data collection and interpretation.

Jan 1, 2005

Previous studies on the blast furnace raceway zone have been undertaken at three levels of scale, namely: laboratory models at low temperature, hot models which simulate coke combustion in the zone, and tests performed on operating and dismantled blast furnaces. This paper reviews the results of this published work on raceways in order to illustrate the factors which affect the raceway shape, size and combustion characteristics. As a result of the work it has been established that raceways are influenced by blast parameters such as velocity, temperature and chemistry, as well

Jan 1, 1981

Although forty-seven years have passed since the by-product coke oven made its successful commercial appearance, it is only during the past fifteen or twenty years that this system of coal carbonisation has advanced rapidly to its present position ofabsolute supremacy.Early designs of by-product ovens proved more or less faulty, and the coke produced was so inferior to coke made in beehive ovens that there was a natural hesitancy on the part of coke producers to invest large sums of money in installations of by-productovens of doubtful utility-more especially in view of the fact that beehive ovens could be erected cheaply and operated by non technical labour for the production of high-grade coke under the most variable conditions of trade.Surely and steadily designers brought forward by-product ovens of improved type, coupled with more efficient apparatus for the recovery of by-products, but still the industry lagged, due almost entirely to the insistence on the part of coke users that the qualityof ordinary beehive coke was vastly superior for metallurgical operations to the best coke produced from by-product ovens. So deep rooted was this prejudice that only the passage of time could eradicate it. That it has successfully done so is strikingly illustratedin the following statistics:

Jan 1, 1928

The mechanism of caving is of interest to the mining engineer only in areas where he is directly concerned. One area is surface subsidence which is outside the scope of this paper. Another area is at the face where coal is being extracted and where control of caving is of vital importance. Coal mining systems have been developed with many considerations in mind, but in this list of considerations, strata control has seldom been given much importance. Research is in progress in Australia to endeavour to determine an optimum sequence for coal extraction underground. As information becomes avail- able from this work it is hoped that appropriate methods of controlling caving in various strata conditions will be devised. When this is done, equipment may be introduced to permit the mining operation to proceed under optimum conditions for strata control, rather than devising a mining procedure to suit the equipment available and methods developed for other reasons.

Jan 1, 1974

By Y Bissiri

The ever increasing demand for metals and minerals is putting significant pressure on current mining companies to find more ore. As these companies explore and mine, the future appears to be to go deeper and deeper underground. With depth, however, comes ever increasing costs as infrastructure such as hoisting, ventilation, the movement of workers and materials increase in size and scope. Further, the actual rock mass becomes prone to destruction through rock bursts and the heat generated becomes a major issue resulting in extreme expenditures in cooling plants and some of the biggest air movers in the world. All these issues result in dramatic changes in both capital and operating costs, subsequently making cut-off grades rise. As this trend continues there is an economic limit to how deep one can go, resulting therefore in a severe shortage of accessible ore deposits to mine. This paper discusses the need for larger marine robotics technology and presents the state-of-the-art in current research in underwater tele-autonomy, specifically the development of high bandwidth optical communication networks critical to any future activities (mining, construction, etc) underwater. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By F Burns, G Peachey

The Hidden Valley process plant has recently undertaken a program to relieve process flow bottlenecks and improve process automation. An environment of cost reduction and restrained capital necessitated solutions that primarily utilised existing equipment and internal resources. Removing bottlenecks relieved pressure from a strained circuit that was unable to maintain consistent performance. Improved process automation firstly stabilised the process, then allowed the circuit to sustainably operate at the expanded capacity limits. These allowed implementation of an operating approach that focused process operators towards identifying and resolving process disturbances in advance. Plant recovery and throughput have markedly improved as a result.CITATION:Burns, F and Peachey, G, 2014. Recent process improvements at Hidden Valley gold mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 43–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

The continued exploration of the major brown coal deposits of the Latrobe Valley has resulted not only in the discovery of huge additional reserves, but also in new concepts of the stratigraphy and structure of the coal seams in that area. The author sets out his interpretation of the new information which has become available over the last six years.A section of the paper is devoted to the quality of the coal. As the chemical composition of these brown coals has been discussed in some detail by previous authors, only the major constituents and the heat value of the coal are dealt with in this paper. Some of the variations in quality are related to the geological structure.The occurrence of underground water and its relation to open cuts is dealt with briefly.INTRODUCTIONThe Latrobe Valley Tertiary Basin is almost entirely covered by a layer of Post Tertiary sediments which mask the underlying rocks and their structures. As a result, the geological understanding of this area has had to await the comprehensive drilling campaign in search of brown coal, initiated by the Victorian Mines Department in 1917, and subsequently carried on by the State Electricity Commission of Victoria. The first detailed geology was published by Herman (1922), and this was followed some 25 years later by papers by Edwards, and later Thomas and Baragwanath, to which reference will be made later in this paper. Herman included a section on the geology of the Latrobe Valley in his book Brown Coal, which was published in 1952.Since that time a considerable amount of new information has become available from the continued drilling carried out by the Commission. In addition, geophysical work carried out by the Commonwealth Bureau of Mineral Resources has assisted in the defining of geological structures in the area.

Jan 1, 1960

By Jamsa-Jouneia SL, Lahteenmaki S

Sophisticated control systems require sufficient and reliable information from the process to be controlled. At the Pyhasalmi concentrator two novel measurements, a particle size indicator (PSI) and a mill level monitor (MLM), have led to significant progress in the control of the grinding circuit. The PSI and the MLM measurements have brought additional information from the process. The PSI has been an absolute prerequisite for determining the overall grinding circuit efficiency and the design of the integrated grinding and flotation control system. The MLM measurement has enabled studies on the volumetric filling of a mill to be utilised for maximising the mill throughput. The paper describes the operation principles of the PSI and MLM devices and the additional process information received. The results of a metallurgical pre-control audit are discussed and finally the design of the integrated control system is outlined.

Jan 1, 1993

By T Baumgartl, D R. Mulligan, D Doley, A Schneider

In arid and semi-arid areas evapotranspiration (ET) cover systems are often used to mitigate contaminated seepage from hazardous mine waste into the adjacent environment. The theory of ET covers is based on the water balance equation with the aim of minimising seepage. While cover systems are commonly trialled, the influences of variability in climate and cover structure on water balance equation parameters are seldom investigated.Water balance equation parameters and their variability were analysed for two ET cover trials constructed from benign waste rock in semi-arid Australia. Seasonal and inter-annual variations in rainfall critically influence cover performance. For successful cover system operation, the average return periods for higher than average rainfall should be taken into account. In addition, failure of ET covers has a higher probability in areas with marked rainfall seasonality. Water holding capacity and plant available water content are low in covers constructed from waste rock. Changes in water holding capacity due to variation in particle size distribution are likely and critically influence cover performance. The application of topsoil can be beneficial for water ingress control through run-off, but a balance has to be struck between run-off, erosion and plant available water. Changes in vegetation composition only influence evapotranspiration water losses at plant coverage exceeding 50 per cent, which is unrealistic in semi-arid areas. This study showed that the capacity of ET cover systems to hold and dispose of received rainfall is often lower than assumed by industry practitioners. Furthermore, in order to improve reliability of long term cover performance, the variability of rainfall and water holding capacity of the cover has to be included in water balance models.CITATION:Schneider, A, Baumgartl, T, Doley, D and Mulligan, D R, 2012. Variability in parameters of the water balance equation and their influence on evapotranspiration cover performance, in Proceedings Life-of-Mine 2012 , pp 293-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By A Bird

Gravity gold circuits have an important part in reducing operating costs and maximising recovery in modern gold plants where coarse gold is present in the ore body. The design and selection of equipment has a vital part in the overall effectiveness of the gravity gold circuit. There are a number of associated factors that need to be taken into consideration when selecting the most suitable equipment for gravity gold circuits including occupational health and safety, security and labour requirements. This paper is a case study that outlines the validation behind the design, selection of equipment and subsequent benefits of the recent upgrade of the gravity circuit at the Marvel Loch gold mine with the main component to the upgrade being the installation of a Consep Acacia Reactor. Since the upgrade there has been a significant increase in gravity recovery, which has reduced the amount of gold reporting to the leaching circuit therefore reducing reagent consumption and overall operating costs. There has been an increase in overall gold recovery and therefore increased gold production. The benefits to occupational health and safety include the removal of toxic gases being released in the gold room during the previous practice of gold concentrate calcination and the removal of the arsenic and nickel from the gold doré, which poses a risk during refining. Manual handling and security has improved as there is no physical contact with gold concentrates during the automated process using the Acacia reactor. The total time for gold room personnel working in the gold room has also reduced from around six hours per day to less than one hour per day.With the continuing development of low grade gold deposits, there will be an increase in demand for low capital, high recovery gravity gold circuits that can significantly increase overall production while reducing operating costs.

Aug 8, 2011

By T Seifert, P Krolop, K Niiranen, S Gilbricht

The Per Geijer iron oxide apatite deposits (IOA) display significant potential mineral resources for Luossavaara-Kiirunavaara AB (publ), known as LKAB. LKAB continuously mines magnetite/hematite ores in northern Sweden for almost 130 years. The Per Geijer deposits reveal a high phosphorus content and vary from magnetite-dominated to hematite-dominated ores, respectively. Furthermore, they show a large variation in texture, mineral composition, and relation to wall rocks. The high phosphorus concentration of these ores results from highly elevated content of apatite as gangue mineral. Reliable, robust, and qualitative characterisation of the mineralisation is required as these ores inherit complex mineralogical and textural features. For this purpose, comminution tests at laboratory scale in combination with scanning electron microscopy-mineral liberation analysis (SEMMLA) were carried out. Based on this work, significant information on the modal mineralogy and degree of liberation of minerals of economic interest (eg magnetite, hematite, and apatite) were obtained. Results show that there is a difference in the degree of liberation of magnetite and hematite between ore types. This seems to be dependent both on the size fractions and the dominance of each iron oxide in the individual ore type. The amount of gangue minerals seems to have no significant impact on the degree of liberation after comminution. Apatite is generally best liberated in ore types associated with silicates, regardless of magnetite or hematite dominance. Based on the results of this study it can be inferred that a high degree of liberation of the minerals of economic interest can be achieved. However, results need to be verified with further beneficiation steps such magnetic separation, apatite flotation and possibly reverse silicate flotation.

Nov 8, 2021

By N Ganjian, A Delavar, F Rashidi Nejad

Iran is one of the most seismically active countries in the world, being crossed by several major fault lines that cover at least 90 per cent of the country. As a result, earthquakes in Iran occur often and are destructive. So, it is important to consider the seismic stability and reliability of all structures including tailings dams.In this study, the tailings dam stability of the Sangan Iron Ore Mine in Khorasan Razavi, Iran is considered for the case study. The tailings storage facilities of the mine have three cells with the capacity of 45 million cubic metres. The first cell, which has three stages of dam raising, has been recently brought into operation. This cell has a downstream-raised retaining embankment. As the risk of seismicity in this area is high, seismic response of this dam was evaluated by numerical methods. To do this, appropriate models were developed for materials used in foundation and body of the embankment. Then for seismic stability analysis, Tabas (Iran – 1978) and Chi-Chi (Taiwan – 1999) earthquake acceleration simulations were applied.The results of this study indicated that the upstream portion of Stage 3 of the dam and dam crest did not experience significant horizontal displacements during earthquake period, but the downstream portion of Stage 3 of the dam showed a maximum horizontal displacement of 60 cm at the third stage of dam raising. This is three times more than what was estimated by the designer. Also, the maximum vertical displacement resulting from simulation of the Tabas earthquake was 35 cm. The results of dam response to Tabas and Chi-Chi earthquakes indicate that displacement, shear stress and pore pressure by the Tabas earthquake were higher than the case of Chi-Chi earthquake. The higher energy of Tabas earthquake and the higher frequency near to the natural frequency of Tabas earthquake could be the reasons of this difference. The results of this case study confirm that if the studied tailings dam impacted by an earthquake of a similar magnitude to Tabas, the dam will be seismically stable and the developed strains will not be significant.CITATION:Delavar, A, Rashidi Nejad, F and Ganjian, N, 2015. Seismic stability analysis of Sangan Iron Mine Project tailings dam, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Zhao, C E. Loo

The flame front is a narrow region in the iron ore sintering bed where coke particles combust. The maximum flame front temperature is as high as 1400°C. At high temperatures, the sinter mix components react to form melts, which facilitates material coalescence and the formation of dense sinter particles. It is well-established that flame front speed is an important factor influencing sinter productivity, sinter quality and fuel rate. In this work, the effect of suction, coke addition and mix moisture on flame front speed was studied in a pilot-scale sinter pot and also using the outputs of a recently developed theoretical model, which takes into account most of the significant physicochemical processes in sintering. Airflow through the bed has a large influence on flame front speed. A power law relationship between these two parameters means that increasing sintering airflow rate will lead to increased flame front speed, but the increases become smaller at higher airflow rates. Sinter pot test results showed that increasing coke addition decreased green bed permeability and increased flame front temperature, which resulted in increased flame front resistance and decreased flame front speed. Studies also showed that green bed properties are sensitive to sinter mix moisture level. The changes in green bed properties further influence the flame front speed and temperature.CITATION:Zhao, J and Loo, C E, 2015. Dependence of flame front speed on iron ore sintering conditions, in Proceedings Iron Ore 2015, pp 83–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D Baas, J Le, R Braun, R Chandramohan, K Hollis, G Lane

The Phu Kham Copper-Gold Operation (Phu Kham) is located in northern Laos, approximately 140 kilometres from the capital, Vientiane. The operation is a producing asset for Australian-based copper and gold producer, PanAust Limited (PanAust) and is operated by Lao-registered company, Phu Bia Mining Limited (Phu Bia Mining). PanAust holds a 90 % interest in Phu Bia Mining. The Government of Laos owns the remaining 10 %.The Phu Kham Operation has recently undergone a series of process improvements to treat the anticipated competent ores scheduled for 2017 and 2018. The operation’s comminution circuit, which comprises a semi-autogenous (SAG) mill and two ball mills, each with 13 megawatts (MW) of installed power, was expected to be SAG mill limited when treating competent basement rock. Ausenco Services Pty Ltd (Ausenco), was engaged to help optimise and enhance the productivity of the Phu Kham comminution circuit over an eight-month period. The work involved participating in and overseeing the redesign of the SAG mill liner systems and developing operational strategies for maximising throughput through to the end of mine life. Ausenco’s comminution optimisation tool, Ausgrind, was used to benchmark and analyse plant data with empirical models, predict circuit performance for varying ore characteristics and evaluate liner wear and predict the life for varying operating parameters. Variances between the actual and the predicted values were assessed in detail to identify missed opportunities, and guiding operating parameters were redefined to maximise throughput and productivity. In combination with the redesigned liner system, optimised process controls for varying ore competencies, and improved operational practices and troubleshooting strategies, increased Phu Kham overall production, exceeding the milling capacity when treating competent ores. CITATION:Chandramohan, R, Braun, R, Lane, G, Hollis, K, Le, J and Baas, D, 2018. SAG mill optimisation and increasing throughput at the Phu Kham Copper-Gold Operation – a success story, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 113–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J D. Grobler

In the heavy minerals industry wet high intensity magnetic separators (WHIMS) are widely applied for primary magnetic separation of magnetic minerals and non-magnetic minerals. This piece of equipment is well known for its robustness to handle a wide range of feed conditions and still produce stable product qualities and yields. A heavy mineral production plant aimed to increase production through their WHIMS plant containing 11 duties and 26 units. Instead of adding new units an alternative approach was followed to firstly maximise the efficiency of the current circuit and secondly to consider possible reconfiguration of the circuit to produce additional product tons for minimal capital investment. In order to characterise the current circuit’s efficiency, identify pockets of excellence and determine the areas for improvement the whole circuit was surveyed several times and mineral mass balances were drawn up.This paper aims to: discuss the modelling process of the WHIMS circuit,explain the calibration and validation process followed to ensure the accuracy, anddemonstrate the sensitivity analysis performed on the different options. From this analysis an efficiency criteria was developed to compare different circuit configurations that enabled the production plant personnel to make an informed decision on the way forward.

Oct 5, 2011

By S Nkwanyana, I Govender

Batch experiments in a 0.6 m diameter mill have shown that improvements of about 13 per cent in the efficiency of energy utilisation can be realised in ball mills by replacing 25 per cent of the ball charge by an equivalent volume of cost-free critical size pebbles from AG/SAG mills. For a mill of a given size, speed and charge filling, the rate of size reduction of ore particles depends on (i) the frequency of grinding media collisions (ii) the probability of capture of ore particles between the colliding grinding media (iii) the probability of fracture of the captured particles. The probability of fracture depends on the magnitude of collision energy. The distribution of collision energy into shear and impact events determines the relative strengths of attrition breakage and impact breakage. The efficiency of energy utilisation depends on which of the two mechanisms of breakage is more desirable in a particular milling stage. In this paper collision data from a series of DEM simulations of a mill charged with steel media and a mixture of steel media and pebbles is presented in energy spectra and spatial distribution maps. The data provides the necessary detail to elucidate the improvements in the efficiency of energy utilisation in ball mills when using a mixture of pebbles and steel media.

Aug 24, 2022