Search Documents

By Hagarty KA

At the northern margin of New Guinea there is a fundamental problem related to the relative timing of arc- continent collision(s) represented in the Papuan Fold-Belt (PFB) and backarc spreading in the Caroline basins. New fission track dates from basement and sediments within major anticlines of the PFB indicate that uplift occurred at 4.0 ¦ 0.5 Ma. The timing is consistent with the fold and thrust shortening (more than 100 km) of the PFB which occurred in the Late Miocene/Early Pliocene as evidenced by the deformed Miocene carbonates and Pliocene molasse deposits. However, in northern Papua New Guinea, earlier work has suggested that ophiolite emplacement and associated metamorphism occurred in the late Oligocene/early Miocene.The evidence suggests that the late Miocene/early Pliocene deformation was of considerably greater magnitude than the earlier obduction event. The Caroline Plate lying north of New Guinea has been interpreted as a backarc basin which commenced spreading in the Eocene and ceased spreading in the Late Oligocene (about 28 Ma). The remnant arc presently docked to New Guinea was active in the Eocene and Oligocene and is believed to be the arc related to the formation of the Caroline Plate. The cessation of spreading of the Caroline Plate has previously been interpreted to be due to arc continent collision during the Late Oligocene/Early Miocene, but such a collision is now known not to have occurred. In the Cretaceous and Palaeocene subduction was to the south beneath New Guinea, but "flipped" in the Eocene to give a north-dipping subduction zone far to the north of New Guinea, driving Caroline Plate backarc extension. This backarc basin reached a limiting size at about 28 Ma resulting in the end of subduction. With the continued northward movement of Australia, Mesozoic oceanic crust was obducted southward onto the New Guinea margin in the Late Oligocene/Early Miocene. In the Miocene south-dipping subduction beneath New Guinea commenced until the now extinct Caroline Plate arc collided with New Guinea in the Early Pliocene, causing extensive regional compression and sinistral strike-slip faulting. This new tectonic framework suggests that backarc basins reach a limiting ridge-trench distance of 1000-1500 knm, beyond which "subduction-pull" cannot drive further spreading so subduction and spreading are terminated.

Jan 1, 1987

The Malvern Hills coal project is now in an advanced stage of development with the stripping of overburden from above former underground workings in which a 3 m seam of subbituminous C coal with very low ash and sulphur was previously mined. The main seam dips at 45¦ to the south-east, along with other adjacent potentially recoverable thinner seams, and the strike extent of past coal mining in the Malvern Hills approaches 10 km with most extraction by underground methods. Overburden and interburden is predominantly weak mudstone, with only very minor sandstone, whilst a 1 - 2 m thick veneer of Last Glaciation loess covers the area. The coal product from the present mine site will supply the local industrial market, with production planned to peak at about 20 000 tpa. Settling pond design has been based on several different approaches, including an estimate of likely inflows from the contributing catchment of about 5 ha under predicted storms having a ten year recurrence interval. A pond of about 1000 m2 in area has been constructed with its invert in mudstone bedrock, and soil slopes have been lined with lime-stabilised clayey loess silt incorporating a gravel armour layer. The pond outflow takes place via a 2 m high 1.8 m diameter concrete dewatering tower, with a skimmer arrangement to lower the pond by approximately 500 mm between storm events. The overflow water discharges to the main stream above a natural wetland, which will act as a secondary polishing pond, and this is to be enhanced in conjunction with the neighbouring forestry company. Discharge consents specify turbidity and pH as the controlling criteria, and both will be monitored at the settling pond discharge point as well as at the entry to the main stream. Investigations to date indicate that the pH of water exiting from previous underground workings is in the range 6.8 to 7.2, and that acidic drainage will not be an issue with this mine site. No dispersive clays have been identified in assessing the overburden and batter materials, although erosion during storm events is expected and all drains will ultimately be routed through the main settling pond to ensure adequate control of runoff-generated sediment. Reestablishment of vegetation on cut and fill batters remains a priority, and ongoing monitoring will ensure satisfactory long-term performance of the pond system.

Jan 1, 2003

By M D. Melville, B C. T Macdonald, J Dixon

The acidic and metal rich waters that are generated from acid sulfate soil (ASS) drainage can have damaging impacts upon ecosystems. The most obvious impact has been the discolouration of water and occasional fish kills. ASSÆs produce these acidic and metal rich waters when pyrite in soil is oxidised. Land management techniques are an essential long-term requirement to minimise the amount of pyrite oxidation. Acidic water that cannot be prevented through land management can be neutralised by other techniques. Powdered lime is the most common material in agriculture that is applied directly to soils and waters. Powdered lime can be expensive and if applied dry it may aggregate. Since the aggregated particles of lime are larger they could sink rapidly in the water column and not react. In waters with high concentrations of dissolved iron and aluminium the lime particles may become coated with a metal oxy-hydroxide precipitate, which will decrease its reactivity. A unique lime-dispensing machine, the Waterways Lime Spreader, has been developed to neutralise acidic waterways. The Waterways Lime Spreader can produce a solution rich in fine lime from larger limestone fragments. The current size of the machine means only 3.5 grams per second of limestone can be emitted. This output will neutralise low acidity waters, however, for high acidity waters the time for neutralisation can be long. More reactive chemicals such as hydrated lime or increasing the size of the machine will reduce this neutralisation time. The Waterways Lime Spreader is also capable of producing slurry mixtures if powdered materials are required. Trials with the Waterways Lime Spreader were undertaken in part of the Clothiers Creek catchment located in northeast NSW, Australia. A small drain with a water volume of 4 m3 was neutralised with crushed limestone to pH 6.9 from an initial pH of 2.6 and an acidity of 902 mg/L CaCO3 in 160 minutes. In comparison a drain with a slightly larger volume of 6 m3 that had an initial pH of 3.2 and an acidity of 753 mg/L CaCO3 was neutralised with hydrated lime to pH 11.8 in five minutes. The Waterways Lime Spreader has been used successfully to neutralise water from acid sulfate soils. It is expected that future applications of the machine may be for the neutralisation of acid rock drainage or acidified lakes.

Jan 1, 2003

By K S. Smith, B P. Jackson, P J. Lamothe

The upper Arkansas River south of Leadville, Colorado, USA, contains deposits of fluvial tailings from historical mining operations in the Leadville area. These deposits are possible non-point sources of acid and metal contamination to surface- and ground-water systems. We used stable-metal isotopes to help ascertain metal retention and release mechanisms that influence metal transport from the deposits to shallow ground-water systems. To accomplish this, we excavated an intact core from a small fluvial tailings deposit and performed laboratory column experiments to examine the amount of metals leaching through the core. Deionised water was continuously applied to the top of the core, and effluent was collected from the bottom of the core for a period of about two months. Three saturation conditions were used, including unsaturated, partially saturated, and fully saturated. Reducing conditions developed upon partial and complete saturation of the core. During the unsaturated leaching phase, core effluents were acidic (pH 2.8 - 3.5) and contained elevated metal concentrations. During a portion of the unsaturated leaching phase, stable-metal isotope spikes and conservative tracers were simultaneously applied to the top of the core. The isotopes provide a means to delineate metal behaviour within the core. During the unsaturated leaching phase, the isotope spikes did not exhibit breakthrough with simultaneously added conservative tracers. However, some of the stable-metal isotope spikes did break through when reducing conditions occurred in the core (during the partial- and completesaturation conditions). In this paper, we use Cd as an example of the utility of stable-metal isotopes in geochemical studies. In the case of Cd, after the core was partially saturated, the 111Cd spike was released as evidenced by a change in the Cd isotope ratios in the effluent. This release continued during the fully saturated leaching phase, however, the total Cd concentration did not increase. These results suggest that the 111Cd spike was retained inside the core during the unsaturated leaching phase, and only partially released as reducing conditions developed. Results from this core-leaching experiment indicate there is a large reservoir of water-soluble material within the fluvial tailings deposit, which yields elevated metal concentrations and high acidity, and which may degrade adjacent ground- and surface-water quality. Use of stable metal isotopes in this study facilitated the determination of different metal-retention processes, metal-release processes, and metal sources in the fluvial tailings deposit in response to changing geochemical conditions.

Jan 1, 2003

By K Akiro

Volcanogenic massive basemetal sulphide and gold mineralisation of predominantly low sulphidation style has been located within Lower Tertiary basaltic and felsic volcanic and sedimentary sequences at Ufuo, in the Left April River area, northwest Papua New Guinea. The four discrete massive sulphide bodies, which have been so far identified, occur within a 3 +5 km area situated within a north west trending structural corridor. The sulphide bodies are all localised on the margins of the corridor where the bounding major through going faults are transected by regional faults. Mineralisation is characterised by massive pyrite-bornite-sphalerite-barite-quartz-anhydrite deposition with later galena-tennantite-chalcopyrite. Minor phases include enargite, goldfieldite and bismuth sulfosalts. Jasperoidal silica lenses and bioturbated sediments are closely associated with the massive sulphides. Basemetal sulphide mineralisation is also closely associated with phyllic-style quartz-sericite- altered host rocks underlying the massive sulphide lenses. This mineralised phyllic alteration is localised to fractures, veins and breccias that cross-cut propylitic style alteration characterised by quartz, epidote, chlorite, adularia and zeolite. The mineralised system possesses several hydrothermal features consistent with a copper-rich submarine exhalative volcanic hosted massive sulphide (VHMS) system, ie discrete massive sulphide bodies with abundant barite, associated jasperoidal silica and bioturbated sediments. However, exploratory drilling of the alteration zone underlying each of the massive sulphide bodies has not identified a well-defined zoned alteration pipe that is characteristic of such systems. The alteration is also similar to that of a porphyry-related low sulphidation system in which phyllic alteration has overprinted a regional propylitic style assemblage. The presence of sporadic enargite (and ?tennantite/tetrahedrite) suggest there were intermittent pulses of acid fluids in the system probably derived from exsolved magmatic SO2 which flowed directly to the surface along reactivated faults. The occurrence of tellurium and bismuth minerals is also consistent with a magmatic contribution to the metalliferous hydrothermal fluids. It is proposed that the VHMS orebodies are the products of submarine exhalative deposition generated by a crystallising magma emplaced within crust of on-going tectonism. Ufuo mineralisation is similar to many VHMS deposits elsewhere in that it is unclear whether the metals are derived from the magma directly, or via seawater leaching of the wallrock. Additional studies such as oxygen isotope analysis may assist in resolving this issue. If the metals are shown to be of direct magmatic origin then there may be good prospects for discovering economic-grade porphyry-related mineralisation at depth below the massive sulphide deposits.

Jan 1, 1999

By M Olsson, U Nyberg, K Widenberg, P Svedensten, F Ouchterlony

During 2007 and 2008, the project Optimal Fragmentation in Blasting II was conducted at the Långåsen quarry of NCC Roads AB near Arlanda. The main goals were:an evaluation of the effect of using electronic delay detonators (EDDs) in quarry blastinga validation of the design curve concept introduced at the Vändle quarry.Five production blasts were monitored. After a first trial round, the remaining four rounds each had about 100 Ø89 mm holes in a 14–19 m high bench charged with site mixed emulsions. In rounds 1 and 2, a tighter pattern than normal was used in one half of the rounds, raising the specific charge there from 0.7 to 1.0 kg/m3. Non-electric initiation was used with two holes per 25 ms delay in-row and 67 ms between rows. In rounds 3 and 4, electronic delay detonators were used instead, with 10 and 5 ms in-row delays respectively.The monitoring encompassed drill hole collaring and alignment, in-hole deviations, the rock structure in the bench faces from 3D imaging, first row burdens, etc. Eleven 400 t samples were taken from the muck piles and sorted in the quarry and sieved in the laboratory (lab). The lab data made up a fines tail that was grafted onto the in-pit sorting data to form sieving curves for the test piles. These curves were then compensated for the absence of boulders to construct the sieving curves for the blasted muck pile.These have been used to derive fragmentation model formulas for the non-electric rounds, also called design formulas. They are based on blast geometry, charging data and the properties of the rock mass. The formulas may be used to estimate the effect of changing blasthole pattern, borehole diameter and stemming length for example.The use of EDDs gave several unexpected results. In comparison with non-electric initiated rounds with a somewhat lower specific charge the fragmentation was much coarser; x50 increased from 160 to 200 mm. The effect of raising the specific charge in the non-electric initiated rounds from 0.72 to 0.99 kg/m3 was a much finer fragmentation; x50 decreased from 160 to 120 mm.CITATION:Ouchterlony, F, Nyberg, U, Olsson, M, Widenberg, K and Svedensten, P, 2015. Effects of specific charge and electronic delay detonators on fragmentation in an aggregate quarry – building fragmentation model design curves, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 727–740 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Battison, R Duggan, S Esen, K Henley, P Dare-Bryan

Increased catch bench crest loss has been observed in recent years at Barrick’s Cowal Gold Mine situated in central New South Wales, Australia. A project was initiated to diagnose the cause of the crest loss, and evaluate ways to limit its effect on final walls.A range of different blast measurement techniques were utilised to evaluate the progressive damage caused to catch berms by presplit, production and trim blasts. Techniques employed included; single point vibration measurement, cross-hole seismic analysis, precision berm surveys, horizontal p-wave velocity measurements, crest loss volume calculation and water level changes between blasts.Blast measurements showed that the majority of damage to the catch berm was caused by the presplit blasts, which registered vibrations greater than 700 mm/s at 5 m behind the presplit line. As a result, considerable changes were made to the blast designs after a series of computer simulations via mechanistic blast modelling (MBM). The uncharged presplit collar was increased from 2 m to 4 m, and every second hole was left uncharged. Vibration modelling using a multiple seed wave (MSW) model was used to optimise trim blast delay timing. Burden relief was changed from 16 ms/m to 27 ms/m using one hole firing per 4 ms time window, and the initiation angle was changed from shallow to steep. These changes in the presplit loading and trim timing helped reduce catch bench crest loss by 1–2 m.Trim shots using a high strength bulk emulsion explosive were also identified as contributors to berm damage after analysis of blast monitoring and MBM modelling. The modelling study resulted in the generation of alternative blast designs to minimise the crest loss, including the use of low-density/low-velocity of detonation (VOD) bulk explosive product (Flexigel™ Advantage) in trim pattern designs. This was trialled on the Northern and Eastern pit walls to evaluate the damage to catch berms on final walls. The trials demonstrated that berm vibration was reduced significantly; fragmentation was similar (or slightly blockier) compared to the fragmentation using the old blast designs; displacement of the berm was reduced, so increased catch bench widths were attained. This paper summarises the trials, and presents a summary of the crest loss to date.CITATION:Battison, R, Esen, S, Duggan, R, Henley, K and Dare-Bryan, P, 2015. Reducing crest loss at Barrick Cowal Gold Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 189–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Roldpo, M Vidigal, J F. C L Costa

The local cumulative distribution function (lcdf) of a selective mine unit (SMU) can be estimated by conditional simulations using the statistics derived from the sample points, generating multiple equally probable scenarios. Conditional simulations permit the evaluation of the lcdf at any support, taking into account the spatial variability, ie the variogram, and the two statistical moments, mean and variance, of the conditioning samples. The SMU ore losses and dilution depend on the mining method and mining equipment selectiveness that, in its turn, depends on the predicted block size. A new approach to predict ore loss and dilution was developed in this study. Monte Carlo simulation is used to randomly generate a grade value derived from the lcdf at the mining stage (Zs_mc(t)) in order to make a decision about the SMU destination, ie processing plant (ORE) or waste dump (WASTE). If Zs_mc(t) is lower or equal to the cut-off (Z_cut-off) the block is ORE and, conversely, if Zs_mc(t) is higher than the cut-off (Z_cut-off) the block is WASTE. Considering these binary destinations ORE/WASTE, at the mining time t, and combining each realisation of the simulated random function Zcs_i (X), there are four possibilities for each SMU simulated value: 1. the block was simulated as ore and is actually ore (OO), 2. the block was simulated as ore and is actually waste (OW),3. the block was simulated as waste and is actually ore (WO), and 4. the block was simulated as waste and is actually waste (WW).The dilution factor is given by possibility 3 (WO), while the ore loss factor is represented by possibility 2 (OW). These results comprise the classical classification and reconciliation plots used in the mining industry. The new procedure proposed in this paper is based on the use of all the equally probable simulations to define the ore loss and dilution factors. An application of this methodology was carried out at Vale's iron mine in Brazil. The grade of silica was simulated and 50 multiple equally probable 3D models were generated. The mean and the standard deviation of the ore tonnage (OO + WO) for the 50 realisations, was 233 Mt and 0.5 Mt, respectively. The mean grade increased for the diluted ore (OO + WO) as well as their respective coefficient of variation (CV). The CV increases from 62 per cent in the undiluted ore (OO), to 101 per cent in the ore, considering the dilution factor (OO + WO). The mean ore loss (OW) was 10 Mt and the waste tonnage dilution (WO) was 9 Mt.

Jan 1, 2009

By K W. Bian, Y M. Liu

Tongkuangyu Copper Mine is currently the only mine in China employing block caving. It comprises two large orebodies known as the No 4 orebody and the No 5 orebody. They are approximately 50° in dip angle, 80 to 240 m in width and 800–1000 m in strike length. The two orebodies are separated by a distance of 110–130 m. Production with block caving originally, ie Phase 1 project started at Tongkuangyu from the first undercut at a depth of 200–300 m below the ground surface and designated as Lift 810 m in late 1989 and has continued to the present. During the last 25 years Tongkuangyu has mined three lifts: Lifts 810 m, 690 m and 530 m. The previous two lifts utilised a slusher process with an annual designed production rate of 4 Mt. In this context the lift name represents the elevation of track haul level.The Tongkuangyu Phase 2 project serves for two lifts (ie Lift 530 m and 410 m) under the elevation of 690 m and the annual designed production rate is 6 Mt. Since the orebody is approximately 50° in dip angle, it is originally designed that production at Lift 530 m is comprised of one main extraction level and two auxiliary extraction levels in the footwall and undercutting is started from one end of the extraction footprint forward to another end, which is from north-east to south-west.Production at Lift 530 m started from March 2011 and reached to 6.39 Mt in 2013 and 6.9 Mt in 2014. Additionally, Tongkuangyu improved block caving processes and used modern mining equipment, which differ from the previous two lifts. Blastholes for undercutting and drawbell-preparation are now drilled using jumbos. The blasted ore is transferred to the underground crushing station via 10 t electric load-haul-dumps (LHDs) and then delivered to surface via a belt conveyor 3200 m long.Due to increasing ground pressure, a consequence of mining depth increase, stress abutment and inadequate support, significant damage occurred at the Tongkuangyu Copper Mine with production at Lift 530 m. This resulted in significant production delays and rehabilitation costs. A series of improvements have since been implemented including an advanced undercut sequence and increased ground support. All of these improvements have allowed Tongkuangyu to alleviate ground control issues, reduce operating costs and ensure safe production.CITATION:Liu, Y M and Bian, K W, 2016. Production at Lift 530 m of Tongkuangyu Copper Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D R Quick

The Goodall gold mine is located 30 km east of Adelaide River, within the Pine Creek 1:250 000 map sheet, at 8 525 000 mN: 750 000 mE, on the AMG grid. The first gold was poured in April 1988 and the mine closed in September 1993, having produced 228 400 ounces of gold from 4.095 million tons of ore, at a head grade of 1.99 g/t. Oxide and primary ore was mined from one large open cut and low grade oxide ore from three smaller pits. The gold mineralisation was discovered in 1981 by means of a helicopter borne rock chip sampling survey, which delineated 13 discrete anomalies. Systematic grid sampling of rock chips outlined an area of 1300 m by 300 m within the 2.0 g/t contour. Over 7500 m of costeaning was used to delineate the A and B-Pod mineralised areas. Geochemical soil sampling played only a minor role in the discovery and geophysics none at all. By the end of 1984, 40 diamond drill holes had been completed and a resource of 3.63 million tonnes at 3.0 g/t calculated. In January 1985, Western Mining Corporation Ltd became a joint venture partner and funded exploration to cam a 60 per cent interest. Additional drilling led to a feasibility study in 1987, based on a Measured and Indicated resource of 4.25 million tonnes at a grade of 2.35 g/t. The host rocks are quartzo-feldspathic wacke and interbedded phyllitic siltstone, of the Proterozoic Burrell Creek formation. The main zone of gold mineralisation, A-Pod, occurs in a sub-vertical vein array, up to 50 m wide and 800 m in length, of quartz and sulphide veins (5-20 mm wide), It is parallel to and on the east limb of an upright, north plunging anticline. Five types of veining have been recognised, with the bulk of the gold mineralisation associated with quartz-pyrite-arsenopyrite and chlorite-quartz-pyrite veins. The gold occurs as particles, from 1-20 micron, as inclusions and along fractures in pyrite and arsenopyrite and to a limited extent in chlorite. The mineralisation is epigenetic and structurally controlled by fractures developed during an earlier folding event. The gold is assumed to have been derived from the underlying sediments of the Koolpin Formation by hydrothermal fluids emanating from the deep seated northern margin of the Cullen Batholith. Precipitation of gold may have been controlled by variations in temperature and pressure.

Jan 1, 1994

By Morgan B. D

Since the mid 1950s, limonite deposits of a new type have been found in the northwest of Western Australia. The deposits consist of extensive fossil valley fillings up to several hundred feet in depth, of medium to high grade limonite, frequently containing limonitized fossil wood, and of Mesozoic or Tertiary age. The distribution of the deposits is closely linked with hilly outcrops of Archaean and Proterozoic jaspilite in the headwaters of the old valleys, from which the iron has been derived by leaching, and presumably re-precipitated by a process not unlike that which operates in forming bog iron deposits. Due to the relative resistance of tlie limonite to erosion, the rejuvenation of streams in the area in recent times has left limonitic remnants as mesas up to· several hundred feet above the levels of the present creeks, the courses of which generally are adjacent to or within a few miles of those of the old limonite filled valleys.The Robe River limonite deposits are the largest of this type known and can be traced for approximately 130 miles along the old stream, over 30 sq. miles of limonite remnants remaining at the present time.The present quantity of limonite in this system alone is probably in excess of 5,000,000,000 tons, and the original quantity must have exceeded four times this tonnage when allowance is made for erosion.Some thousands of millions of tons of this material contain in excess of 54 per cent Fe, with approximately 10 per cent combined water. The chief impurities are SiO2 and Al2O3, and minor elements are not present in objectionable amounts. A portion of these deposits was extensively tested by The Broken Hill Proprietary Company Limited (the B.H.P. Co. Ltd.) during 1962-1964. Most of the data presented in this paper are based on the work done on these deposits which are typical of those discussed. The overall problem of the origin of the limonite is discussed. It is apparent that the limonite originates from the jaspilitesof Archaean and Proterozoic age which form the highlands at the upstream ends of the deposits. The iron oxide has been chemically and/or mechanically derived from these jaspilites and deposited by one or more of the following mechanisms.A.-Chemical-sedimentary mainly by biological agenciesB.-Replacement of fluviatile sediments by iron-charged watersC.-Clastic sedimentary processesD.-Lateritization of fluviatile sediments.These various mechanisms are discussed; the authors favour machanismA.Manuscript received' at The Institute, 14th July, 1964.

Jan 1, 1964

By Blockley J. G, Laeter J. R

The history of the Ph-Cu-Zn mineralisation in the orthampton Block of Western Australia has been further investigated. It was hoped that (1) Rh-Sr studies on partially-remelled granulites, wall-rocks to the dolerite dykes, should date the dolerite intrusion, (2) Rh-Sr data on hydrothermally-altered dolerite should date the sulphide mineralisation, (3) Pb model ages on the galenas might provide an independent dating of the mineralisation, in addition to any geochemical information that might be derived. Only the second dating aim was fulfilled, but the Pb isotope data, when combined with the Rh-Sr data, have permitted deductions about U, Th and Pb abundance changes during the regional metamorphism, and about a possible source of the ore Pb. In detail the following has been found. (1) The partially-remelted granulitic wall rocks yield a scattered whole-rock Rh-Sr isochron which seems not to have been reset by the dyke intrusion (age 1037 ± 146 Ma, with initial Sr ratio 0.7171 ± 0·0054, MSWD = 111). This date agrees well with that reported previously for granulites from another locality; together theyestablish the time the metamorphic period closed. (2) The hydrothermally-altered dolerites yield a Rh-Sr whole-rock date 434 ± 16 Ma, with initial Sr ratio 0.7072 ± 0·0029 and MSWD = 31, taken as referring to the time of Ph-Zn mineralisation. This contrasts with a report of much older palaeomagnetic and K-Ar datings of the dolerite (not less than 550 Ma, possibly older) and suggests that neither the dolerites nor their heat have had any connection with the mobilisation of the Pbscavenging solutions. (3) The Pb isotope ratios of galenas from the ores yield a well-correlated regression which is not amenable to any of the model-age calculations. (4) The Pb-isotopic trends negate any genetic connection between dolerite and mineralisation, but the country-rock granulites could be the Pb source. (5) Combination of the Rh-Sr dates and the Pb data in a "simultaneous isochrons" construct permits the inference of major losses from the system during the regional metamorphism, in the order U>Pb>Th, with substantial homogenisation of the remaining Pb. This left a wide range in local UlPb and Th/U among the source rocks which eventually were scavenged by the mineralising solutions. (6) These geochemical deductions are shown to be compatible with previously-published information on the abundance ofU and Th in the Northampton Block granulites, which are thus seen to be credible as source rocks for the ore lead.

Jan 1, 1985

By K Nesbitt

Draw control at Premier Mine is considered important to avoid conditions of isolated draw, which results in early waste ingress, compaction of the kimberlite ore and loss of ore reserves. The Premier Mine kimberlite pipe is unique in that the pipe is cut at a depth of 400 metres below surface by a 75 metre thick gabbro sill. All cave mining at Premier is below the sill and failure to exercise good draw control could cause early ingress of gabbro waste. Gabbro causes problems in the diamond recovery plant and the amount of gabbro sent to the plant needs to be closely monitored. Fortunately coarse gabbro fragments are easy to recognise in drawpoints. It was anticipated that only 85 per cent of available ore would be drawn from the blocks immediately overlain by the gabbro sill before excessive gabbro waste forced the closure of drawpoints. Data on tons drawn per drawpoint and loaded per LHD as well as the tons tipped per pass is gathered by the vehicle monitoring and control (VMAC) system and information recorded by the load-haul-dump (LHD) drivers. Draw control staff monitor drawpoints on a shift basis and record the occurrence, type and height of hang-ups. Information pertaining to the status of the drawpoint in terms of support, waste and availability is also recorded. A database has been compiled that has been used to analyse the overall pattern of draw control, the frequency of occurrence of different types of hang-ups, secondary blasting efficiencies and drawpoint and LHD productivity. The gabbro sill has provided a unique marker horizon that has allowed the arrival of rock from a level 100 metres above the production level to be recognised. Data shows that ore migrates extensively towards groups of drawpoints that are heavily drawn with many drawpoints more than 100 per cent drawn before gabbro waste was recognised. This indicates that an accurate mixing algorithm is essential for good draw control. Data on tons drawn, drawpoint availability, productivity and the occurrence of various types of hang-ups has allowed better control of the mining operation and provided data for planning future caves. In the BA5 mining block a drawpoint spacing of 22 metres, horizontally across the major apex, has still allowed drawpoints to be pulled to waste with no loss of ore. In the BB1E mining block the drawpoint spacing has been increased to 23 metres and no problems have been experienced to-date. Future initiatives centre on improving the data gathering integrity of the vehicle monitoring and control system and a linear programme that will optimise draw control and productivity.

Jan 1, 2000

By T Wellman, G Sternadt, R Hingston

The 335 000 oz Wilber Deposit is located within the Meekatharra-Wydgee Archaean greenstone belt in the Murchison District of Western Australia. The deposit comprises high-grade gold mineralisation hosted within a steeply west-dipping quartz lode, which lies within a broader (20–60?m) north-east striking shear zone envelope. Locally, the northerly-trending host rock geology includes greenschist facies high-Mg basalt (albite, actinolite, chlorite, biotite, calcite, zoisite, muscovite and titanate) intruded by at least two generations of felsic to intermediate porphyries (albite, actinolite, zoisite, chlorite, sericite, biotite, quartz and titanate). The Archaean rocks are cross-cut by a number of east–west striking Proterozoic dolerite dykes (biotite (50 per cent), albite, carbonate, epidote, titanate and actinolite) that are interpreted to have intruded pre-existing regional structures. The entire mine package is cross-cut by a system of shallow north-east-striking, north-west-dipping, barren quartz veins that commonly contain large (up to 30 cm), euhedral, smokey quartz megacrysts.The north-east-trending lode lies within a 3 m wide shear zone and varies from a single discrete 0.5 to 4 m wide laminated, massive or brecciated quartz-carbonate vein to multiple laminated veins up to 1 m wide within the shear. The veins exhibit strong boudinage, with cross-cutting quartz-carbonate seal veins in the boudin necks. The boudin necks often contain pink calcite. The shear zone fabric wraps closely around the boudin necks proximal to the vein, becoming more lode parallel distal to the vein. The lode is offset by a north to north-north-west trending fault.Mineralisation occurs as free gold within the quartz carbonate veins, with accessory sulfides including pyrite ± chalcopyrite, ± galena ± sphalerite. Fuchsite is observed in the veins, as laminar wall rock inclusions, with visible gold commonly associated with the wall rock laminations.Gold grades range from less than 1 g/t within the hosting shear zone, either at the margins or interstitial to the veins, to approximately 30 g/t in the single vein, and up to greater than 60 g/t in the multiple vein areas. Gold is commonly visible and disseminated throughout laminated, breccia and massive quartz veins, although laminations show the highest concentration of gold grains.CITATION:Hingston, R, Wellman, T and Sternadt, G, 2014. The geology of the Wilber Deposit, Andy Well Gold Project, Murchison District, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 55–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By J D. Pease, J M. I Tuppurainen, P D. Munro

This paper examines how legislation and regulation can be external drivers of technical change in mineral processing and extractive metallurgy and how the industry can respond. Two examples are considered; the production of copper metal from concentrates and the cyanide process for gold production.The Clean Air Act (1970) in the USA initiated a wave of attempted innovations in the extractive metallurgy of processing copper sulfide concentrates to meet forthcoming standards on sulfur dioxide emissions. Interestingly, a satisfactory technical solution existed (flash smelting and gas capture) but had not been widely adopted.Nearly fifty years later the primary copper industry finds itself with new challenges. One major challenge is how to deal with the increasing level of arsenic in copper concentrates. Most countries impose an upper limit on arsenic in imported concentrate; typically, 0.5% As or less. Higher arsenic concentrates can be blended with cleaner ones to meet the limit, but this tactic cannot be used indefinitely as the average arsenic level of global concentrates rises inexorably. Further, smelters (often in urban locations) cannot be expected to deal with both ever-increasing arsenic in the feed and stricter restrictions on emissions and disposal. A rising “inventory” of primary copper deposits are already constrained from development by high arsenic concentrate. These deposits will need to be developed if future copper demand is to be met. An economic and technical solution to arsenic is needed. The gold industry may also face challenges in the use of cyanide, by far the dominant lixiviant used in gold and silver production. Public perception has driven restrictions on the use or transport of cyanide in some jurisdictions. History suggests that such pressure is only likely to increase. While there are several alternative lixiviants, none can yet match the utility and economics of cyanide.Such important issues will not be resolved by incremental change or new equipment items. They require development of new process technology - a tectonic event rather than an incremental change. It requires sustained effort (and expenditure) over decades and is very unlikely to result from “business as usual” for producers, suppliers or academics. Past major process developments were driven by a dire need for economic survival or by legislative change. What will drive the future changes?CITATION:Munro, P D, Pease, J D and Tuppurainen, J M I, 2017. Technology change by regulation – a cresting wave?, in Proceedings MetPlant 2017, pp 45–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D Hope, D K. Mukhopadhyay, J D. Harvey

South32 (S32), a globally diversified mining and metals company, is listed on securities exchanges around the world (ASX, JSE, LSE), with its primary listing being on the Australian Securities Exchange (ASX). Chapter 5 of the ASX Listing Rules (Australian Securities Exchange (ASX), 2019b) requires a mining entity to provide a summary of governance arrangements and internal controls with respect to its estimation processes, estimates and reporting of Mineral Resources and Ore Reserves annually. As a global company, it is also important to design and implement all governance processes and internal controls which can be used consistently across the organisation. The three lines model (previously known as the ‘three lines of defense’ model) is employed across South32 to manage risk where the first line (Practitioners) designs, implements and executes processes and controls to manage risk; the second line (Stewardship) identifies material gaps and improvement opportunities in the first line by monitoring conformance with the group requirements, legislative and regulatory obligations. Second line also assists with the development and improvement of core fundamentals based on industry good practise. The third line (Group Assurance) provides independent and objective assurance over the Group’s system of risk management and control. The estimation of resources and reserves for most of the operations within South32 is managed by the Planning function. The estimation process is part of the annual Life of Operation Plan (LoOP). The LoOP identifies and assesses the strategic alternatives for the development of an operation and recommends the preferred pathway based on value and risk. The LoOP starts with opportunity framing and the updated resources as an input and ends with the short-term plan and annual budget (the outputs). Ore Reserves estimates are one of the outputs from the LoOP. All the inputs and outputs follow internal standards and procedures which includes peer review and performance reconciliation. Stewardship (Second line) which is a centralised function has standards in place to ensure compliance to internal controls and external regulatory requirements. This includes assessment of the competence of Competent Persons, technical reviews, independent audits and training in the relevant chapters of the ASX Listing Rules, Guidance Notes and Appendices. Group Assurance (Third line) which reports to the Risk and Audit Committee of the Board of Directors ensures the design and operating effectiveness of the processes, standards and procedures associated with the estimation and reporting of resources and reserves. While the level of scrutiny has a different intent for each line in the three lines model, the overall purpose is to achieve a consistent outcome across the organisation

May 24, 2023

By S Robinson, A Turner, R Dale, C Butler

"Sandfire Resources NL- (‘Sandfire’) DeGrussa definitive feasibility study (DFS) identified geometallurgy as a major factor in achieving optimum plant performance at the DeGrussa mine. A geometallurgical initiative was created to proactively investigate this issue, and a key initial achievement was the 2013 paper by Condon et al (2013) on developing a working geometallurgical model from first principles. Significant advancements in Sandfire’s geometallurgical understanding since that publication now shape how information is presented and communicated.The main geometallurgical parameters so far identified as critical factors affecting plant performance are Cu:S ratio, iron sulfide mineralogy, talc carbonate content and sphalerite content. Apart from specific mill strategies, geometallurgical issues have been managed through communication between departments and strategic run-of-mine (ROM) pad management.This paper uses the current theories of geological evolution of the volcanogenic massive sulfide (VMS) deposit at DeGrussa, to discuss the variability between the orebodies C1, DeGrussa (sea floor mounds) and C4, C5 (sub-sea floor replacement) to highlight the different issues each orebody is expected to encounter when processing.A zone of altered low-grade mineralisation surrounds the main orebodies at DeGrussa, referred to as a halo. Talc minerals are often patchy within this halo and often cause significant recovery issues during processing. This halo has been successfully modelled using MgO as a proxy. The ability to model the talc material assists with both identifying potentially problematic zones for processing and geological interpretation of the ore deposits evolution.Early in geometallurgy studies at DeGrussa it became apparent that it would be useful to identify processing performance prior to mining. This necessitated the incorporation of specific sulfide species into the mining block model. These attributes are interpolated from the logged sulfide estimates allowing a clear picture of the abundance of each mineral type within a defined area.In conjunction with the block model a geometallurgical factor (GMF) graph was developed, identifying sulfide mineralogy based upon mineral assays. These two recent additions to the model provide a clear picture of the nature of the ore sources that will be presented to the processing plant.The future of geometallurgy at DeGrussa will see these tools used to aid mine scheduling with a view to further improve processing recoveries.CITATION:Butler, C, Dale, R, Robinson, S and Turner, A, 2016. Geometallurgy – Bridging the Gap between Mine and Mill: a Case Study of the DeGrussa Geometallurgy Program, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J Herrmann, J Richards, B Hutchison

An extensive trial of laser-based survey and monitoring systems at Hillgrove Resources Kanmantoo Copper Mine in the Adelaide Hills, South Australia, has proved the capabilities of the system in monitoring rock movements on open pit walls. Initially, the trial involved deploying a Maptek I-Site 8820 laser scanner and the proof-of-concept Maptek Sentry software in the Nugent Pit to monitor ductile rock movements located up to 260 m away. The system was proven to be capable of monitoring various rock movements from 1.5 tonne rockfalls up to a 40 m high toppling wall failure. Data collected from smaller rockfalls was used to help build a database for Hillgrove’s rockfall management program. As part of the trial, the laser scanner was deployed to monitor a ramp movement event, as well as the toppling failure, adjacent to an IBIS slope stability radar. Both devices monitored the slump and the slowly developing toppling movements, with similar results. Although the radar was used as the successful ‘critical alarm’ device for the toppling failure, post-failure analysis showed the laser-based system to be capable of performing a similar role in the ductile rock regime; albeit over much shorter distances than the radar capability. A second laser scanner was deployed to monitor Kanmantoo’s Emily Pit in early December 2014, where it successfully provided critical alarm warnings for a block topple event. Sentry software, which takes advantage of Maptek I-Site 3D spatial imaging technology, was first released in November 2014 to meet industry demand for a cost effective, flexible system to detect movement. Sentry has now been re-launched as a fully transportable monitoring system. Deployed in a custom trailer, the system offers a power and communications module, cellular and Wi-Fi networking and a stable bollard for the I-Site laser scanner and Sentry software. This paper will present rock wall movement data from the Sentry trial and a subsequent two years of monitoring of the open pit walls at the Kanmantoo Copper Mine, at distances out to 750m. In addition, examples of remote geological mapping and small rockfall detection, using the laser scans, will be described. The Sentry system has proven to be beneficial for the continual improvement of slope monitoring and risk management at hard rock mines. CITATION:Hutchison, B, Richards, J, Richards, J and Herrmann, J, 2018. Mine rockfall and rock wall failures – proven digital laser-based approach for monitoring slopes at the Kanmantoo Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 463–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By B Hawkins, S Durkin, V Lawrence

The requirement for secondary egress from underground workings has long been regulated in Australia. Escape way systems have evolved from simple airleg rising ladders and timber ladders to steel galvanised ladders and more recently fully enclosed polyethylene ladders.The polyethylene ladder, Safescape Laddertube, was introduced to the underground mining industry in 2010. It is an enclosed cylindrical modular plastic ladder designed for use in underground escape ways and access ways. Since its first installation in May 2010, the Laddertube has been installed in 43 mines across four countries, totalling 8800 m of ladders installed to December 2013.The Cracow Gold mine is one operation using Laddertube, located 500 km north-west of Brisbane, Queensland, Australia. Upon discovering and developing both the Empire and Roses Pride orebodies, a safe and economically viable secondary egress system and surface primary ventilation exhaust shafts were necessary to support development and production activities to these workings. The need arose to merge these two critical requirements together between surface and underground mine workings some 200 m and 400 m respectively for each orebody. Neither egress has intermediate access points within their full service length from top to bottom. Several options were considered, the preferable and most feasible method adopted was Laddertube.The longest egress length requiring Laddertube within the two vertical surface exhaust shafts was 400 m long, within a 3.5 m diameter shaft. Due to the length of the vertical Laddertube system in both egresses, personnel are to be assisted by mechanical means using the Extended Ladder Climb Assist system.The Gossan Hill mine also uses Laddertube for their escape ways. Part of the Golden Grove operation, Gossan Hill is an underground sublevel open stoping mine located in the mid-west of Western Australia.With a considerable mine life remaining and a history of acidic water and stress related deterioration in vertical openings, the mine operators sought an escape way solution that would provide for the long-term needs of Gossan Hill. Laddertube was selected due to its non-corrosive properties and the ability to fill in around the ladder way to provide stability to the raise opening.Laddertube is a recent development in escape way systems, and is effectively being applied in a variety of operations, meeting the specific needs of underground mines.CITATION:Durkin, S, Hawkins, B and Lawrence, V, 2014. The application of Safescape Ladders at the Cracow and Golden Grove operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By G Nicholas, S Coward, J Vann, R Wolff, S Jackson, S Moayer, A Bye

"A new approach to mineral project evaluation is described called Scenario-Based Project Evaluation (SBPE). SBPE incorporates well established æscenario planningÆ and æscenario thinkingÆ approaches, which are used extensively in other industries,?most notably the?petroleum industry. While most scenario planning is qualitative and non-probabilistic, the approach described here includes both quantitative and qualitative aspects. SBPE is complementary to optimisation approaches and allows mining firms to build and operate projects that are more robust in the face of adverse changes as well as proactively respond and exploit the upside offered by a realistic assessment of variability. The approach has potential to improve project performance and decrease operational risk. It also has important applications for currently operating mines.Conventional evaluation of metalliferous mineral deposits uses estimates of metal grades and deleterious attributes in singular æorebody modelsÆ, usually 3D block models, which fail to capture two critical aspects that underpin the realised value of mining projects: the inherent uncertainty of the estimated attributes the spatial variability of attributes, at the scale of mining selection, which impact on downstream processing steps and fundamentally drive realised value. While singular models are appropriate for estimating block averages, conditional simulation (CS) models of the relevant attributes are needed to represent uncertainty and capture spatial variability. Any attributes that can be either built into CS models and/or modelled in the envisaged mining/processing steps, can be evaluated fully through to highly ægranularÆ (ie detailed and un-smoothed) cash flows. A complete view of SBPE relies on selected strategies being tested against plausible æscenariosÆ of factors external to the project and thus outside management control. æExternalitiesÆ captured in such scenarios include market prices, costs and taxes. Via SBPE, project managers may demonstrate that there is material value in preserving or purchasing options that provide future flexibility to respond to the changing externalities or changes in orebody performance. Such flexibility generally comes at a cost but is very difficult to value. It is argued that full value chain evaluation using SBPE can help to value these options for a mining company. A case study for a gold mine is presented.CITATION:Vann, J, Jackson, S, Bye, A, Coward, S, Moayer, S, Nicholas, G and Wolff, R, 2012. Scenario thinking - A powerful tool for strategic planning and evaluation of mining projects and operations, in Proceedings Project Evaluation 2012, pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012