Search Documents

By S J. Chen, N Jiang, Y S. Ding, F X. Li, D W. Yin, F Wang

This study assessed the deformation failure characteristics of rock-coal composites with different height ratios. Uniaxial compression tests were conducted using an acoustic emission monitoring system and XTDIC three-dimensional full-field strain measurement system. The results showed that with the increase in rock-coal height ratios, the uniaxial compressive strength of composite samples increased from 5.26 MPa to 14.61 MPa. The evolution of the deformation localisation zone of the composite samples is closely related to the initiation and propagation of the primary cracks in the coal samples. At the moment when the main fracture of the coal samples occurs, there is a large drop after the peak of the stress-strain curve of the composite samples, and the height of the rock samples increased to varying degrees, which indicated that the failure of the coal samples induced the rebound deformation of the rock samples. With the increase in rock-coal height ratios, the rebound deformation amount of the rock samples decreased from 0.042 mm to 0.008 mm, and the rebound deformation rate decreased from 0.210 per cent to 0.010 per cent. Meanwhile, the rock samples’ rebound deformation releases part of the elastic energy to act on the coal sample, further contributing to the destruction of the coal samples. Compared with single composite coal samples, the coal samples of the composite samples have much more failures. In addition, with the increase in rock-coal height ratio, the input energy density, elastic energy density, post-peak release energy density, and residual elastic energy density of the composite samples increased, the dissipation energy density decreased, and the percentage of pre-peak elastic energy density increased from 98.56 per cent to 99.86 per cent. These results revealed the deformation failure characteristics of rock-coal composite with different height ratios and provided a theoretical reference for understanding the underground dynamic rock failures.

Nov 29, 2022

By M Barley, C A. RosiFre, L Lobato

The Carajßs iron ore deposits contain approximately 17.5 billion tons of ore with >64 per cent Fe and occur in the eastern part of the Amazonas Craton. They are hosted by jaspilitic banded iron-formation (BIF) of the Carajßs Formation which, together with metavolcanic rocks, comprise the ~2.75Ga Grpo Parß Group of the Itacai·nas Supergroup in the ~1000 km long, E-W trending Carajßs Synclinorium. The Carajas Formation comprises discontinuous layers and lenses of partly dolomitised BIF (17 - 43 per cent Fe and 35 - 61 per cent SiO2) and lenses of high-grade iron ore, cut by mafic sills and dykes. The high-grade iron ores occur as large tabular bodies of friable (soft) hematite with smaller lenses of hard (compact) hematite. The hard hematite ores typically occur at the contact with the underlying volcanic rocks and are surrounded by an aureole of hydrothermal carbonate alteration. BIF that has been overprinted by dolomite and magnetite crystallisation has recently been discovered at depth in the N4E Mine. With increasing amounts of carbonate, the original lamination (microbanding) and other fine primary structures in the BIF have been progressively obliterated resulting in alternating carbonate and iron oxide mesobands. The friable hematite ore that is characteristic of the Carajßs deposits results from ongoing weathering and leaching of the carbonates from this type of altered BIF. The hard hematite ores probably result from more extensive early oxidation. The association of both carbonate-altered and jaspilitic BIF with the N4 Mine is similar to that observed at the Mount Tom Price deposit in Western Australia, where carbonate-altered BIF occurs below massive hematite ore with a jaspilitic halo developed above the orebody. This indicates that as at Mount Tom Price, hydrothermal carbonate alteration and associated loss of silica from BIF may be an important step in the formation of these giant hematite deposits.

Jan 1, 2002

By G Corbett

Epithermal Au-Ag deposits form in the upper 1 km of the crust and are therefore best preserved in the less eroded Pacific rim arcs, although also recognised elsewhere. Two profoundly different ore fluid types give rise to low and high-sulfidation styles apparent as variations in ore and gangue mineralogy as well as characteristic zoned wall rock alteration. Low sulfidation epithermal Au deposits are derived from near neutral composite magmatic-meteoric fluids and divided into a group with a stronger intrusion association within arcs grading in time and space from: quartz-sulfide Au + Cu, to carbonate-base metal Au, and the epithermal quartz Au + Ag, whereas in strongly extensional settings the influx of meteoric waters promotes the development of chalcedony-ginguro banded Au-Ag epithermal veins. In the presence of continental crust particularly in Latin America polymetallic Ag-Au veins represent a Ag-rich equivalent of carbonate-base metal Au and passes upwards to chalcedony-ginguro Au-Ag style. By contrast high-sulfidation epithermal deposits are deposited from an acidic magmatic fluid which provided characteristic hydrothermal alteration by reaction with wall rocks grading outwards as mineral assemblages dominated by: vughy silica, alunite, pyrophyllite-diaspore, dickite-kaolin and then illite-smectite neutral clays. Au mineralisation is commonly refractory with enargite deposited dominantly later within the silica zone.Exploration for epithermal Au deposits benefits from an understanding of the controls to mineralisation which commonly give rise to the development of ore shoots with widest and highest Au grade ore zones. In low-sulfidation systems a combination of competent host rocks, dilatant structures, higher grade styles of mineralisation and efficient mechanism of Au deposition, contribute towards ore shoot formation. High-sulfidation epithermal Au systems occur in permeable volcanic and breccia host rocks which are linked by major structures to the magmatic source.CITATION:Corbett, G, 2013. Pacific Rim epithermal Au-Ag, in Proceedings World Gold 2013 , pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G D. Price

The Golden Blocks Goldfield is located in the Slaty Creek area,North West Nelson, about 20 km west of Collingwood. Alluvial gold was discovered in Slaty Creek in 1861. Gold was mined from quartz veins up to 1.5 m thick at nine mines from the 1890s until the closure of the Aorangi Mine in 1911. Total production from the Golden Blocks Goldfield is estimated at 46 000 ounces of gold. The Aorangi Mine was the largest mine, with a recorded production of 27 978 ounces of gold at an average grade of 36 g/t. Quartz veins containing gold and sparse sulphide mineralisation occur in a slightly metamorphosed, complexly deformed over-turned sequence of Lower Ordovician sandstones and shales. Primary gold mineralisation is associated with intensely deformed zones that occur near or at carbonaceous shale and sandstone contacts. Some eighty-five percent of all gold production (39 000 ounces) came from four mines confined to the stratigraphically lowest, most widespread shale unit. The quartz veins exhibit textures consistent with a hydraulic fracturing mode of vein formation with fissure infill vein types predominating over replacement textures. Stylolites of carbonaceous material and recrystallization features within the veins suggest multiple phases of deformation. The lack of wall rock alteration, and low primary fluid inclusion temperatures of 200¦ - 265¦ indicate that the ore fluids were associated with a low temperature epithermal system. A model consistent with similar mineralisation styles observed in Ordovician sediments from Pacific Rim occurrences is presented. The high grades (up to 100 g/t) mined from the upper levels of several mines suggests supergene enrichment processes associated with the Upper Cretaceous weathering surface. The Golden Blocks Goldfield has had no modern exploration. The most recent exploration was undertaken in the early 1980s. There are known acid intrusives in the area, with potential for the application of new models of intrusive-related gold mineralisation.

Jan 1, 2004

By R Herbert, M E. Malmstr÷, S U. Salmon

The study focuses on sulfide oxidation processes in unweathered pyrite-rich mine tailings from a soil-covered impoundment in northern Sweden. To simulate the oxygen-limited conditions in water saturated tailings two long-term column experiments were performed. Results are presented for the first 11 months of the experiments at room temperature. The tailings used in the experiments were of two different grain sizes (one coarse grained, in the range 0.02 - 0.6 mm with a grain surface area of 1.86 m2 g-1, and one fine-grained, in the range 0.0015 - 0.06 mm with a grain surface area of 10.00 m2 g-1) and with slightly different mineralogical composition. The S:Fe molar ratio in the leachates (1.0 - 1.5) indicates either that pyrrhotite is the main iron sulfide undergoing oxidation in our experiments, or, alternatively that the S:Fe molar ratio in the leachate is determined by pyrite weathering in conjunction with other processes releasing iron or immobilising sulfate. However, speciation modelling of the leachates indicates that ferrihydrite was close to saturation, suggesting that a ferric oxyhydroxide may have dissolved/ precipitated during the experimental period, thereby affecting the S:Fe molar ratio. Pyrite oxidation rates obtained from the two column experiments during æsteady-stateÆ were 2.25 + 10-13 and 8.45 + 10-14 mol m-2 s-1 in the coarse and fine tailings, respectively. Pyrrhotite oxidation rates, as an alternative, were 2.31 + 10-12 and 1.24 + 10-11 mol m-2 s-1 in the coarse and fine tailings, respectively. Natural microbial activity was confirmed in both the tailings and the leachates; therefore, the obtained oxidation rates are not strictly abiotic. It is thus concluded, based on the experimental results, that tailing heterogeneity will result in zones with different oxidation rates, related to their physical and chemical properties.

Jan 1, 2003

By Z Endut, T F. Ng, G H. Teh, J H Abdul Aziz

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Gold mineralisation at the Penjom gold deposit in the Central Belt of Peninsular Malaysia is hosted in structurally-controlled quartz-carbonate veins that display a variable degree of overprinting events under a ductile-brittle regime. Mineralised veins are categorised into two main types: shear and extension veins. Shear veins are interpreted as forming during the fold and thrust episode (D2 event) along the bedding and the Penjom Thrust ore zone. The shear veins are associated with discordant extension veins. In addition, NE- to NNE-trending splays and Penjom-Thrust-parallel reverse-dextral and locally NNW to N–S reverse-sinistral faults overprint earlier vein events, forming a new episode of extensional veins during the D3 event. This is mostly at the fault contacts of intrusives, either as shallow-dipping or vertical-sheeted stockwork or brecciated veins. At least two episodes of faulting comprising D4-D5 are evident, which postdates the main episodes of veining and mineralisation. This is indicated by a series of late episode N–S-trending sinistral and oblique to normal faults that transect and displace the Penjom Thrust and the folded footwall sequence at low angles, and are interpreted to be responsible for intensive vein deformation along the Penjom Thrust and displacement of the orebody. Structural interpretations of mineralised veins suggest that the veins were formed under a compressional to transpressional regime, with later post-vein displacement in a transtensional to extensional regime. Vein formation in response to deformation observed at Penjom reflects regional structural deformation within the Central Belt of Peninsular Malaysia and specifically along the Bentong-Raub Suture zone.CITATION:Endut, Z, Ng, T F, Abdul Aziz, J H and Teh, G H, 2015. Style of veins in Penjom gold mine, Malaysia – implications for gold mineralisation and structural episodes, in Proceedings PACRIM 2015 Congress, pp 507–514 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Multi Torque Industries and Jadefoil have developed a safer, more efficient method of explosive protection, retention, placement, and constraint. In particular, this refers to advancements in airbag technology, where the system will offer an alternative to conventional gasbags and decking methods to provide a far more controlled and safer working environment. Airbags have provided operator control and reliability which has not until now been possible in this type of application. The benefits have been noted by current users and the advantages have provided an increase in productivity and significant savings in explosive waste. Obvious problems with gasbags lie in their instability in hot conditions where the danger is associated with gas canisters exploding with great force posing a significant risk to operators. Other problems associated with the decking systems currently on offer is the lack of versatility and operator control. The airbag systems give the operator full control to guarantee accurate placement, assured retention whilst boasting a quick operation of less than a few seconds for conventional void blocking, decking and plugging. One of the main advantages of the airbags is that the operator has full control over placement and retention force, therefore in wetter conditions where slippage can be a problem extra air can be added at the operatorÆs discretion to ensure a sufficient grip. Technical calculations coupled with experimental testing have demonstrated that an airbag will support the weight of a 30 m water column in an 89 mm hole at an initial bag pressure of 5 psig. Applications are increasingly growing whilst more customers embrace their use. Advancements such as the ability to deck in overhead holes, block voids in overhead holes at any depth, explosive retention in very wet conditions, longhole stabilisers to prevent hole closure and concertinaed liners reflect a dynamic potential for new technologies. All of these applications provide a decrease in explosive waste, an increase in operator safety, an increase in explosive protection, and an increase in productivity.

Jan 1, 2004

By Fredley D. C

Georgius Agricola wrote in De Re Metallica in 1556 that a prudent a miner should not work in a region ruled by a tyrant-a person inimical to mining. In 1926, Associate Chief Sherman of the United States Forest Service in a speech stated, "It is the policy of the Forest Service to encourage the development of the mineral resources within the boundaries of the National Forests ... a man who fails to cultivate a friendly, helpful, cooperative spirit in his relations with those who are endeavoring to develop the mineral wealth of our mountains has no place in the Forest Service." Both statements are as true today as they were in 1556 and 1926. The challenge to the Forest Service and the mineral industry today is to maintain that cooperation in a world that has changed significantly since Agricola and Sherman. The United States Forest Service manages 77,000,000 hectares of land-mostly in the Western United States-an area equal in size to New South Wales. The vast majority-75 million hectares are National Forests, and 1.6 million hectares are National Grasslands. National Wilderness Areas account for 13 million hectares or rough- ly 17 per cent of the National Forest System. National Forest System lands (NFS) are some of the most visible, scenic and controversial lands in the country. They are also some of the most valuable for their mineral potential and production. The value of mineral produced exceeds US$4 billion per year. There are over 1200 producing mines, 15,000 oil and gas leases, and some of the largest lead, copper, silver, gold, platinum, molyb- denum, and coal deposits in the hemisphere. Every year the Forest Service approves nearly 5,000 mineral operations on the NFS. Much of the NFS (75 per cent) is open to location of mining claims pursuant to the 1872 Mining Law. And an equal amount of land is legally available for oil and gas leasing.

Jan 1, 1991

By R M. Tosdal

Intrusion related ore deposits are widespread in the Central Peruvian Cordillera Occidental and adjacent high-plains to the east and include porphyry Cu (-Au, Mo; eg Morococha), Cu-Zn (Pb-) skarn (eg Antamina), Pb-Zn-Ag carbonate hosted vein deposits (eg Uchucchacua), cordilleran base metal (eg Cerro de Pasco) and epithermal deposits (eg Quicay). Geochronology and petrochemistry of intrusive rocks associated with mineralisation reveals that: most ore deposits were emplaced in the late middle to early late Miocene; and are related to calc-alkaline granodioritic igneous rocks with Sm/Yb >3, Sr/Y >40 and Y/Th <1.5. The largest deposits, including Antamina, Colquijirca and Cerro de Pasco are associated with intrusions with Sm/Yb >4 and which, as indicated by Pb and Sr isotopic data, have undergone relatively moderate middle and upper crustal assimilation. The chemical signature of igneous rocks related to mineralisation likely reflects melt equilibration in the lower crust at a crustal thickness of more than 45 km. Mineralisation was favoured by a change from normal to flat subduction, resulting in increased compression, crustal thickening and subsequent cessation of the magmatic arc. Premiocene ore deposits do occur, but are restricted to a broad E-W corridor between Uchucchacua and Milpo and probably were controlled by a crustal-scale structural discontinuity across the strike of theAndes. Not all igneous rocks with high Sm/Yb and Sr/Y ratios did acquire their trace element signature in the lower crust. Petrographic and Pb isotopic evidence indicates shallow crustal hornblende fractionation or assimilation of pelitic material as possible causes for high trace element ratios in some rocks. These are apparently unrelated to polymetallic mineralisation. Thus, critical evaluation of petrographic and geochemical data in metallogenetic studies, especially in areas with complex basement architecture such as Central Peru is critical and should not be reduced to simple trace element ratios. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By A Xenidis, N Papassiopi, I Paspaliari

Acid generating sulfidic tailings covering a surface area of approximately ten hectares have been deposited in the historic mining area of Lavrion in Greece. For the development of a remediation strategy, the performance of three alternative acid generation control techniques was assessed under actual field conditions. The techniques involved the application of dry covers, including a synthetic HDPE liner and a compacted clay layer with capillary barriers. Furthermore, the potential formation of a low permeability hardpan layer at the sulfidic tailings surface by limestone addition was investigated. The field tests covered an area of 2500 m2, which was divided in equal quadrants, corresponding to the control plot and the three alternative remedial options. To monitor the amount and quality of percolated water, lysimeters were installed beneath the four plot areas. Based on the monitoring results over a period of six years, due to the dry climate encountered in the Lavrion area, a low amount of water percolates through the pyrites if no action is taken (control area), corresponding to 20 - 25 mm per year. This water is highly acidic, pH = 1.2, and contains a heavy load of contaminants, eg Fe 40 g/L, Zn 15 g/L, and As 1.5 g/L. The HDPE cover eliminated the percolation of water into the material for a period of five years, whereas thereafter the volume of leachates increased to values similar to those recorded in the control plot. The water collected in the lysimeter of the clay cover has been minimal corresponding to approximately five per cent of the drainage volume produced in the control area. In the fourth plot, which involved limestone addition to sulfidic tailings, the volume of drainage initially collected was almost double compared to the control area. After three years of monitoring, significant reduction in the amount of percolated water was observed, attributed to the formation of a cemented layer (hardpan), at a depth of 40-80 cm from the testpad surface.

Jan 1, 2003

By M Csar

The Nicolsons Find gold project is located 35 km southwest of Halls Creek in the east Kimberley. It was discovered in the late 1980s by John Nicolson and Stuart Skoglund, when high grade gold mineralisation within outcropping gossanous quartz reefs was found. The area has produced a modest 28 150 ounces of gold over two brief mining periods in 1996 and 2002 - 2003. Indicated and inferred resources as of September 2011 stand at 1 384 000 t at 5.58 g/t Au for 248 500 ounces of gold.The project is situated within the Halls Creek Orogen. Principal host units are metasediments and volcaniclastic sediments of the Koongie Park Formation. Minor mafic units are also recognised. Immediately east of these units, emplacement of the loadstone granite is believed to have provided the structural setting for the later gold mineralising event.Mineralisation is hosted within a broad, brittle-ductile arcuate shear zone about the western contact of the Loadstone granite. In the Nicolsons Find area, the shear zone strikes north-northeast and within the shear zone, gold is hosted in a series of narrow, quartz rich veins up to 200 m in strike length, plunging moderately to the north-northeast. To date, mineralisation has been drilled to a depth of 360 m below the surface. The veins are stepped or en-echelon in nature with low gold values towards the quartz vein limits where compression is inferred and higher grades present in the dilational body of the quartz veins. Gold is fine grained and can be present with or without associated sulfides. Sulfides are generally minor and consist mainly of arsenopyrite with traces of chalcopyrite, pyrite and sphalerite. Where present, sulfides are generally indicative of higher gold values.CITATION:Csar, M, 2012. NicolsonÆs Find gold project, East Kimberley, Western Australia, in Proceedings Narrow Vein Mining 2012 , pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

The mill area of PT Freeport Indonesia is located in a valley surrounded by steep natural slope, characterised by extreme topography with mountains rising to above 4500 m within 100 km from the seashore. The valleys are deeply embedded into the mountainous terrain and bordered by steep natural slopes. Vertical or overhanging lime walls are interrupted by steep vegetated screen sections containing accumulated loose material from weathering processes and ancient rock falls and/or debris flows/avalanches. The climate can be best described as alpine subtropical with an accumulated rainfall of more than 5000 mm per year. Occasional snowfalls and superficial freezing above 4000 m elevation leads to heavy weathering of the superficial rock layers and along open joints and fractures. The mill area is a crucial and strategic infrastructure for the entire mining operation which is best characterised as a high density industrial area with facilities including water tanks, power generators, crusher, and concentrating facilities including office buildings and workshops as well as access tracks to the underground mining blocks. Considering the local topography, the restricted space conditions and the number of technical installations, the facilities are likely to be affected and highly vulnerable to rock fall from the surrounding slopes. In order to minimise the rock fall hazard three rock fence barriers area were constructed at the mill area. The 7.5 rock fence barriers were designed with the maximum capacity of 5000 kJ. These are the largest capacity of rock fall barriers ever constructed in Indonesia. The total length of the barriers for the three locations was 126 m. The biggest challenge of this project was the construction of the barrier at West Gulley, which was constructed at 300 m above ground level. For this site, construction access was undertaken using helicopter. This presentation discusses the design of the mitigation structures as well as the construction approach and stages of the barriers. Please note: This paper is abstract only.

Nov 25, 2010

The discovery of nickel sulphide deposits at Kambalda in 1966 heralded the development of ò an industry with a capital value of over $1.5 billion producing about 10% of the western world's nickel. ò an unprecedented exploration boom in which over $200 mil- lion was expended in 10 years in the search for nickel deposits. ò a major new class of nickel deposits stimulating exploration for similar deposits overseas. and rapidly propelled a struggling small mining and exploration company to become one of Australia's corporate giants, provid- ing a much-needed stimulus to economic activity in a region suffering from a severe downturn in its principal industry, gold mining. Production of nickel in Western Australia commenced at Kam- balda in 1967 and grew rapidly to a rate of over 30,000 t of con- tained nickel per annum in 1970, 40,000 t in 1973 and 50,000 t in 1975. Early production was aided by a shortage of nickel on the world market due to disruption of supply from the major Canadian producers, resulting in high free market prices for the metal. Since these early years, the industry has experienced a number of cycles of indifferent health due principally to market developments overseas, although the level of production of nickel in Western Australia remained fairly consistent. The two most serious of these, in 1977-8 and 1985-6, forced the closure of a number of mines. Current nickel prices are allowing remaining producers to enjoy a measure of relative prosperity, although there is little general speculation that this will be long-lived. Nickel deposits discovered in the exploration boom were almost exclusively related to ultramafic rocks. Volcanic peridotite (komatiite)-associated deposits, exemplified by the Kambalda ore- bodies, were the targets of initial exploration which was concen- trated on ultramafic sequences near lower stratigraphic contacts with underlying mafic rocks. Subsequently, discoveries made in coarse-grained dunites in interpreted intrusive settings broadened the search parameters.

Jan 1, 1988

By L N. Loganathan

Risk exposure in tunnel projects is extremely high due to various factors such as variability of subsurface conditions, selection of inappropriate design and tunnelling methods, improper risk assessment on adjacent surface and subsurface structures and utilities, and inadequate contractual practices. The risks in tunnelling must be borne by the contractor, designer and the owner of a tunnelling project. There have been a number of improvements in the last ten to 15 years in the manner in which tunnel projects are developed and implemented in terms of their design, construction, financing and operations. One significant improvement has been the manner in which underground conditions and their risks are being managed. Owners are less willing to transfer the full responsibility to the contractor for managing the underground conditions, although this is a familiar manner in which underground major urban projects have been previously contracted and managed. The owners of tunnel projects in Singapore have advanced the risk management process for their projects through geotechnical interpretative baseline reports (GIBRs), geotechnical data reports (GDRs) and project specifications (PSs). This paper discusses industry practice and its development as well as the application during the preparation and use in Singapore on the Deep Tunnel Sewerage System (DTSS) and the Marina Coastal Expressway (MCE) project in Singapore. The DTSS trunk sewer is 48 km and ranges from 3.3 m to 6 m finished diameter up to 50 m below the ground. The underground conditions ranged from Old Alluvium, strengths of about 1 MPa to competent Bukit Tima granite, with strengths of over 230 MPa. The total route length of the MCE is about 5 km. About 3.6 km will be constructed underground, consisting of dual five-lane carriageways. The underground construction will be cut-and-cover, and 2.6 km will be constructed about 13 m underground, and 1 km of tunnel will range from 13 m to 24 m as the tunnel passes under a 420 m wide reach of Marina Bay, whose crossing will be constructed as a two-phase cofferdam.

Jan 1, 2008

By Mackenzie W. R, Harding C. G

The Islamic Republic of Mauritania is a large country of over 1 000 000 square kilometres situated on the Atlantic coast of north-west Africa. It is bounded to the north by Western Sahara and Algeria, to the east by Mali, and to the south by Mali and Senegal. With the exception of a narrow strip in the south along the Senegal River valley, the country lies entirely within the Sahara. The north of the country is largely devoid of vegetation, and it is estimated that 90 per cent of the population of 2.1 million people live in the southern quarter of the country. From about the turn of the century, Mauritania was ruled by the French from Dakar in Senegal and, until 1960 when it obtained independence from the French, Mauritania did not have a capital. Today, the capital is Nouakchott, home to an estimated 600 000 Moors of mixed Arab, Berber and African descent. After independence in 1960, disputes over Spanish Sahara to the north led to a military coup in 1978 and it was not until 1991 that a democratic constitution was adopted. The new constitution declares Mauritania to be an `Islamic, African, and Arab Republic.' It provides for an executive president, elected for a six-year term, and for a bicameral legislature, consisting of a national assembly and a senate. The first presidential and legislative elections were held in 1992 under United Nations' supervision. Mauritania's economy is predominantly pastoral, and the country depends heavily on foreign aid. Its principal export industries are iron ore mining (about ten million tonnes per annum from mines near Fderik in the north) and fishing. Mines d'Or d'Akjoujt SA (MORAK), a company in which General Gold Resources NL (GGR) has 42.5 per cent equity, produces over 50 000 ounces of gold per annum, which represents the third largest export industry in the country.

Jan 1, 1996

Lafayette Mining Limited, a listed Australian company, is developing a polymetallic Project on the island of Rapu Rapu, located to the east of southern Luzon in the Philippines. The Rapu Rapu Project is based on the Ungay deposit, which has proven and probable reserves of 6.0 million tonnes of 2.5 g/t Au, 28 g/t Ag, 1.2 per cent Cu and 2.1 per cent Zn. The Project will produce copper and zinc concentrates from a sulphide flotation plant as well as dore from a CIL gold plant. Average annual metal production over the projected six-year mine life is 9800 tonnes of copper, 14 000 tonnes of zinc, 50 000 ounces of gold and 590 000 ounces of silver. Despite a rich mineral endowment and long mining history, there have not been any significant new mine developments in the Philippines since the early-1990s. The investment climate has been affected by legal challenges to the 1995 mining code, civil unrest in parts of the country, the impeachment of the previous President and community concerns about the industryÆs environmental performance. As a consequence, the Rapu Rapu Project is viewed as a test case û within both the country and the international mining industry û on whether minerals investment in the Philippines is an acceptable business proposition from a risk perspective. Lafayette has faced formidable challenges in managing the development risks of the Project. The major risk areas of the Project for which the company developed strategies include: regulatory, environmental and approvals issues, technical evaluation, project development, social and community issues, land acquisition, and financial and marketing issues. This paper describes the risk management strategies successfully pursued by the company, and which have the Project on track to commence construction in 2003. Dealing with each of the areas in turn, Lafayette sought to develop strategies which either effectively neutralised, minimised or otherwise addressed the key risks most likely to be experienced.

Jan 1, 2003

Hindered settling devices (teeter bed, up-current) are widely used in the mining industry to classify mineral streams into various size fractions and to separate minerals. In the coal industry these devices are extremely successful in separating coal of low densities from shale and pyrite. In the beach sand and in the iron ore industry, this equipment is used to beneficiate minerals either as stand alone units or lately as classifiers in spiral circuits. The challenge that these applications give to metallurgists is to be able to simulate the equipment by using mathematical models with or without the aid of small bench scale tests. In any green fields and many brownfields projects, limited amounts of samples make pilot plant tests difficult. Although there are mathematical approaches available, the accuracy is of such a nature that it can not be used for design purposes. This refers to the use of StrokeÆs law, NewtonÆs and the so called intermediate law as is widely published. Research done by the author indicates that in most applications none of the above laws apply. Using the original data as published by Perry and Chilton (Chemical Engineering Handbook, pp 5-64, 1973) and re-plotting it indicates that the settling velocity of particles is a function of (particle diameter)n where n varies between 1.2 and 1.6 which is different from that predicted by the intermediate law that suggests that n = 1.18. Another way of describing the relationship between the drag force and the Reynolds number is done by iterating between settling velocity and the Reynolds number. This needs more computer time but the accuracy obtained from this does add value to simulations. A small but simple test is suggested to determine the settling velocity of particles to enable metallurgists to determine variations from the theoretical calculations to determine the influence of viscosity and particle shape.

Jan 1, 2008

By P Licence, M Stevens, P Atkinson, J L. Mauk

The Rahu and Ascot epithermal Au-Ag prospects are two km north of the Karangahake deposit in the Hauraki Goldfield, and all occur in an approximately 6 km2 north-south elongated magnetic æquietÆ zone. The prospects are hosted by andesitic flows, lithic-crystal tuffs and local sedimentary rocks; local silica sinter occurs at Ascot. These host rocks are intensely altered by quartz, adularia, albite, chlorite, pyrite, illite, interstratified illite-smectite and calcite. Several minerals show zoned distributions, such as widespread adularia that overlies more localised and deeper albite. Illite is the only dioctahedral phyllosilicate in several drill holes, but elsewhere it forms a shallow carapace underlain by interstratified illite-smectite with 50 to 90 percent illite. Veins are common with quartz dominating near the surface and calcite becoming more abundant at depth. Local laumontite-calcite veins also occur. Pseudosecondary and secondary fluid inclusions in quartz and calcite at Rahu and Ascot have homogenisation temperatures (Th) that range from 162¦ to 268¦C and 128¦ to 243¦C, respectively. Most inclusions have trapped dilute fluids with salinities of less than 1.9 weight percent NaCl equivalent, but 20 percent of the inclusions have salinities of 2.0 to 10.5 weight percent NaCl equivalent. Calculated paleowater table elevations suggest that the water table at Rahu occurred at 440 m above sea level (asl). At Ascot, silica sinter formed from discharging geothermal fluids (=100¦C) at the paleosurface at ~135 m asl. However the sinter also contains comb quartz with pseudosecondary inclusions that have a Th average of 229¦C, corresponding to a paleowater table at ~430 m asl during inclusion entrapment. Taken together, these results suggest that the Ascot sinter was buried by approximately 300 m of cover material during a major volcanic or tectonic event, and that subsequent hydrothermal fluids formed veins and alteration at Rahu and deposited comb quartz at Ascot.

Jan 1, 2007

Over the last 20 years the mining industry has played a key role in the further development of many Central Queensland and New South Wales communities. The number of people who are employed by the coal mining industry, the number of transient residents, shift work and the town facilities have all contributed to how the community views the coal mining industry. As the coal mining boom continues and the mining communities continue to grow more emphasis is needed to address the community concerns, specifically the socio-economic and environmental impacts that the coal mining companies may have on these communities. Central Queensland coal mining operations are situated in the Bowen Basin. Many of the towns in the region have been developed specifically for the coal mining industry with 13 - 50 per cent (Australian Bureau of Statistics, 2006) of people living in the communities being directly employed by the mines. The introduction of shift work, differing rosters and the mining boom have resulted in considerable changes to these communities with more transient contractors and permanent employees taking up residence outside of these communities. This change, however, has not been as noticeable in the Hunter Valley region. The Hunter Valley, situated in the Sydney Basin has two main mining towns, Singleton and Muswellbrook. Of the 37 173 (Australian Bureau of Statistics, 2006) people that reside in the communities 13.8 to 16.5 per cent (Australian Bureau of Statistics, 2006) are employed directly by the mines. The Hunter Valley is a large tourist destination due to its many vineyards; this results in a diverse community where mining is not the sole means of employment. Similar to Central Queensland the mining boom has brought more people to the Hunter Valley region, although greater percentages have taken up residence in the communities. The views vary between the two regions on the coal mining industry, specifically on the socio-economic and environmental impacts that the industry may have on the surrounding communities.

Jan 1, 2008

In a ætypicalÆ gold deposit each tonne of ore will contain tens of millions of very fine gold particles, whereas; at Bendigo the majority of gold in each tonne of ore is present in just five to 15 very coarse gold particles, a distribution more akin to diamond deposits. At Bendigo the minimum sample size required for good assay repeatability is estimated at 4.5 t for each assay. Drill core samples are several orders of magnitude too small to generate representative assays.The drilling data are characterised by a nugget effect approaching 90 per cent, a very skewed distribution and, on average, under-report in situ grade by 50 per cent to 75 per cent. Since 2002 Bendigo Mining NL has completed 47 000 m of diamond drilling, 1200 m of on reef development, collected and processed 100 bulk samples (150 t each), 800 mini bulk samples (50 kg each) and processed in excess of 25 000 t of ore through a pilot plant. The results of this work have provided the information required to develop and verify a robust grade estimation procedure. No standard geostatistical manipulation of the drilling assay data can generate an accurate grade estimate as the samples and associated assays are not representative of the ore being sampled. The recognition of this fact was critical as a radical transformation of the raw drill assay data was required to develop a workable methodology for grade estimation in such a high nugget environment. The aim of the transformation was to reduce the nugget effect and high variance and so approach a lognormal assay distribution. Ideally the average drill grade would approximate actual in situ grade and the assay distribution would reflect actual grade distribution within the reefs. Following the data transformation simple block modeling within the defined resources allows grade estimates to be made that can be used in the estimation of Indicated Resources and hence Probable Reserves. The grade estimates have been checked by extensive bulk sampling and processing of 25 000 t of ore (three per cent of total resource) through a pilot plant with planned full scale mining to provide the ultimate verification.

Jan 1, 2004