Search Documents

ATTENTION has recently been directed to the subject of dust production and methods of allaying same in the Broken Hill mines, so that the time would seem opportune for the local branch of the Institute to discuss certain features of an important phase of the health question in connection with underground work. Tests conducted in the Broken Hill South mine and at other mines at Broken Hill have shown that the ordinary operatioils of mining, such as boring, blasting, and shovelling, may be accompanied by the production of considerable dust unless water is judiciously used.In South Africa·dust particles under 5 microns size are regarded as dangerous, becailse they are so small as to be invisible to the naked eye, and wm esc'ape the protections set up by nature in the nose and throat, and thus may be inhaled in large quantity. A micron is 1 25000th part of an inch. This paper contains an account of the work done on the Broken Hill South mine chiefly, though some tests were done on other local mines.An acknowledgment is due to Mr. T. A. Reid, of the Broken Hill South mine, who conducted some of the tests herein mentioned, and under whose supervision most dust counts were made. Numerous dust samples have been taken by means of thekonimeter, an instrument designed by Dr. Kotze, the Government mining engineer of the Union of South Africa, and fully described...

Jan 1, 1921

CSA mine, which is a deep level copper operation, located 12 km north of Cobar, NSW, currently uses a top down stoping method, utilising cemented hydraulic backfill (CHF) to fill and stabilise the stoping void thus assisting the extraction sequence. The stope sequence then requires development back through the CHF stope so that the necessary infrastructure for the subsequent stoping, such as raise bore pads can be sited. The primary and secondary support installed in the CHF consisted of 100 mm thick fibrecrete from floor to floor with 7 + 2.4 m long resin support tendons installed at 1.5 m ring spacing. This support system relied on the resin achieving a quality bond with the CHF, and also the fibrecrete developing early structural strength due to the use of an accelerator. In addition to the delays in the excavation turn around time, it was felt that a superior support system could be designed. Such a system was designed; risk assessed, tested underground, and trialled in selective CHF digouts, and eventually signed off as the chosen support method in CHF digouts. This paper discusses the change from a passive support system used in CHF digouts to an active support system using Swellex bolts and weld mesh, which has provided an active support system, that is superior, faster to install, reduced the excavation turn around time and is overall a cheaper support system.

Nov 25, 2010

By D A. Kepert, D Clark

During early 2004, Fortescue Metals Group (FMG) began an aggressive exploration and drilling program in the Chichester Range, targeting iron enrichment developed in the Nammuldi Member at the base of the Marra Mamba Iron Formation. The timely recognition by FMG of distinct zones of (hypogene) microplaty hematite (mplH) enrichment overprinted by extensive supergene mineralisation led to an early reappraisal of the geological history of the area and characterisation of the possible structural and stratigraphic controls on mineralisation. Regionally, the Chichester Range dips gently at less than 5¦ to the south, however, detailed mapping shows that this regional limb is overprinted by low amplitude, long wavelength, north/south to northeast/southwest trending folds. The locations of major structures in the Marra Mamba Iron Formation, combined with spectral analysis of known mineralisation, allowed extrapolation and prioritisation of exploration target areas. The delineation under cover and understanding of these structures was enhanced by detailed airborne magnetic data. Recognition that supergene mineralisation was associated with a palaeotopography that continued significantly under cover to the south under sediments of the Fortescue River valley led to the discovery of extensive supergene mineralisation together with additional mplH mineralisation. A model for the landscape evolution and preservation of enriched Nammuldi Member was generated in order to help communicate both the complexities involved with targeting drill holes beneath cover and the potential limits to the lateral extents of mineralisation.

Jan 1, 2005

By McLennan T, Howells E, Zastawny H, Watt J. S

Nuclear techniques have been used to determine the solids weight fraction (W) and ash content of (fine) coal in slurries independent of voidage variations. The method is based on the correlation between W and the hydrogen concentration Hsl (wt/wt) of the slurry. Hsl is determined by combining measurements of neutron moderation and ?-ray transmission. Both Wand ash content are determined by combining the above measurements with the ash-sensitive measurement of X-ray backscatter compensated by a measurement of iron K X-ray intensity.The nuclear analysis system, called the SIRO coal slurry gauge, has been proved in a six-week plant trial at the BHP Steelworks washery at Newcastle, NSW. Several probes, each containing a radioisotope source and scintillation detector, were immersed directly into the coal slurry in the feed box upstream from the bank of flotation cells. For 140 samples W, ash and voidage varied in the ranges of 0 to 13 wt percent, 26 to 41 wt per cent and 0 to 4 vol. per cent, respectively. The r.m.s. difference in solids weight fraction, determined by probe measurements and conventional assay, was 0·52 wt per cent. Ash was determined with an r.m.s. difference of 2·0 wt percent in the coal. Better sampling techniques were used in the last half of the plant trial, and r.m.s. differences were 0.35 wt per cent solids and 1·5 wt per cent ash.

Jan 1, 1986

By M I. Pownceby, M A. Rhamdhani, S Palanisamy, D Fellicia, B Satritama, G A. Brooks, A Ang

Metal production have long been using carbon sources as both reducing agents and energy sources. Consequently, the global extractive metal sector contributes significantly to greenhouse gas emissions, accounting for approximately 9.5 per cent. Hydrogen gas offers as a promising ecofriendly alternative to carbon in metallurgical processes, serving as both a reductant and energy supplier with a by-product being only water vapour. However, the implementation of molecular hydrogen faces certain challenges related to the thermodynamics and kinetics of metal oxide reduction. In addressing these challenges, researchers have explored the application of hydrogen plasma, generated by subjecting molecular hydrogen to high energy to produce atomic, ionic and excited hydrogen species. Hydrogen plasma offers thermodynamic and kinetic advantages over molecular hydrogen and carbon-based reductants, exhibiting lower standard Gibbs free energy of reaction and activation energy. Therefore, hydrogen plasma can produce metal in fewer steps, process any oxide feed and feed size and even be used to refine metals. Despite these advantages, challenges exist in utilising hydrogen plasma in extractive metallurgy, including electricity costs, potential reverse reactions and industrial-scale implementation. This study provides a mini review of prior research on hydrogen plasma for metal oxides reduction, particularly iron oxide, as well as state-of-the-art techniques for its use in extractive metallurgy applications by mentioning several reactor types. Future prospects and scale-up possibilities of the hydrogen plasma in extractive metallurgy will also be presented.

Aug 21, 2024

By Chitombo GPF

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have heen identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By G P. F Chitombo

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have been identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By P Nissen, T Jenke, M Ralph, M Cattani, M Quinlan

The West Australian Government hold an annual ‘Mines Safety Roadshow’ around the State’s regions and the capital city, Perth. Each year presenters provide an update on legislation and safetyrelated themes. A recurring theme is the mining industry fatality rate. Professor Michael Quinlan’s ‘Ten Pathways to Death and Disaster’ (Quinlan, 2014) has been referenced regularly to assist in structuring workshops and conversations concerning fatality prevention in the mining industry. The ‘Ten Pathways’ are the outcome of an analysis of fatal injuries in the mining industry, which identified a series of common themes to the fatalities: Pathway 1: Design, engineering, technical and maintenance flaws. Pathway 2: Prior warnings or causes for alarm ignored. Pathway 3: Failures in risk assessment. Pathway 4: Failures in management systems and hazard management plans. Pathway 5: Failures in auditing. Pathway 6: Economic pressures compromising safety. Pathway 7: Failures in regulatory oversight and inspection. Pathway 8: Worker and others expressing concern prior to the incident. Pathway 9: Poor management – worker communication and trust. Pathway 10: Emergency and rescue resources and procedures. To determine a fatality risk profile we asked participants at the Mines Safety Roadshows to indicate their perception of their employer’s performance in each of the Ten Pathways. We administered the questionnaire at the Mines Safety Roadshows in 2017, 2018, 2019 and 2023. In this paper, we report on the results of the questionnaires, and suggest how organisations can improve their fatality risk score.

Apr 16, 2024

By K Ehrig, C Lower, V Liebezeit, M Smith, E Macmillan

"Minerals, minerals, minerals. Elements occur in the earth as minerals. If local physical, chemical and structural conditions are conducive to concentrating these minerals to sufficiently high abundances in the earth’s crust, a mineral deposit will form. If technology is available to extract metals from the minerals economically, then you have a mineral resource that will be mined and processed. Determining which minerals are present and quantifying their abundances, textural characteristics (grain size and shape) and how they are intergrown with each other is the realm of the mineralogist. Geologists use this mineralogical data to understand how the mineral deposit formed, how to find high-grade zones within the deposit and where to find other mineral deposits. Metallurgists use this data to design, operate and optimise processing facilities to extract metals from the minerals. The types, quantity and precision/resolution of the mineralogical data required by geologists and metallurgists are different, but are not mutually exclusive of each other. Fortunately, measurement technology is available that is relatively rapid, high volume and low cost, thus enabling ore and gangue mineral characterisation at a historically unprecedented scale of a mineral resource.CITATION:Ehrig, K, Liebezeit, V, Smith, M, Macmillan, E and Lower, C, 2014. Geologists and the value chain – how material characterisation by modern mineralogy can optimise design and operation of processing facilities, in Proceedings Ninth International Mining Geology Conference 2014, pp 5–14 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By Waghorne E. P

The State Electricity Commission of Victoria is Australia's largest single coal producer. Approximately 19 Mt of coal will be produced in 1989 from the SEC V's newest mine, Loy Yang Open Cut (LYOC), which com- menced overburden stripping operation in October 1982. When the adja- cent Loy Yang Power Station is completed in the late 1990's, LYOC will supply between 35 to 45 Mt/a, depending on power station performance and demand of coal for non-power generation uses. LYOC has been a major challenge for the SECV. It is the biggest single open pit coal mining development undertaken in Australia, with a whole of life capital cost approaching A$1 billion. The mine has supplied a very rapidly growing demand for coal from the expanding power station while developing in breadth, length and depth. Coal demand has consistently been above the figures anticipated during the initial planning because of the substantially improved performance of the 500 MW units of the Loy Yang A Power Station. The superior performance of the LYOC and power station has generated additional electrical energy during the first 5 years of power station operation compared with the initial planning targets- at almost no additional capital cost. This has been a major benefit to the SECV. LYOC will continue to present major challenges for the SECV, particularly in achieving overburden removal and coal reserve targets as development of the open cut continues to full depth over the next 15 years.

Jan 1, 1989

By R Hall

The magmatic arcs of SE Asia and SW Pacific contain some of the worldÆs major magmatic-hydrothermal gold deposits. Most gold deposits in SE Asian and SW Pacific arcs formed during periods of plate reorganisation rather than during periods of normal or steady state subduction. These plate reorganisations were caused initially by the collisions of the Australian Craton with the Philippines-Halmahera Arc and the Ontong Java Plateau with the Melanesian Arc at ~25 Ma. A second Mid-Miocene period of mineralisation accompanied plate reorganisation following maximum rotation or extrusion of Indochina and cessation of spreading in the South China Sea at ~17 Ma. However, the vast majority of deposits from New Zealand to Taiwan formed since 7 Ma during an important period of tectonic reorganisation that accompanied and followed changes in the relative motion between the Indian-Australian and Pacific plates between ~8 and 3.5 Ma. Magmatism in unusual tectonic settings produced the most abundant and largest deposits with many deposits associated with high-K calc-alkaline, shoshonite, adakite and alkaline magmatism. In particular peak mineralisation appears related to melting of sub-arc lithosphere that has been previously modified by subduction. During large-scale plate reorganisation this can occur towards or at the end of a period of normal subduction, following arc collision or accompanying subduction reversal at approximately the same time in different parts of a complex system of arcs such as in SE Asia and the SW Pacific.

Jan 1, 2005

Dr. F. L. Stillwell. Segnit's article puts forward the views that the rocks associated with the Broken Hill lode are simply highly metamorphosed sediments, tbat metasomatism on a large scale was not an important factor at Broken Hill and that the rocks and lode were contemporaneously metamorphosed.In particular, the garnet quartzite, the most abundant rock in the limited section of the mine examined by Segnit, is described by him as a simple, metamorphosed manganiferous sediment.These views, while consonant with those of H. F. King (1958), are drastically opposed to those of myself and others e.g. Gustafson et al. (1950, p. 1383) who state that the most extensive hydrothermal alteration in the district is in and close to the zinc lodes in the Zinc Corporation and New Broken Hill Consolidated Ltd. mines. Segnit's conclusions conflict with 1. the absence of any manganiferous sediment in the Broken Hill district except in close proximity to the lode,2. the clear cut metasomatism of the dolerite dykes which indicates that the ore is younger than the dykes and therefore post-metamorphism, and 3. the petrofabric study of den Tex (1958) which provided independent evidence that the ore in its present form post-dates all events of a diastrophic nature in the area.The original sediments of the district were mudstones and calcareous sandstones with 2 to 5 per cent CaO. These have been converted by high grade metamorphism into sillimanite gneisses and quartzites characterized by the presence ...

Jan 1, 1962

By E A. Agorhom, P N. Aabulleh

The bulk of the worldÆs production of iron ore is processed into steel. The needs of the steel industry therefore demand a high exploration and exploitation of iron ore. One trend within the industry has been a great increase in the demand of iron ore and this is reflected in an increase in world steel production from 1955 to date. In addition to the high demand for steel, is ChinaÆs high appetite to feed its steel industry. It is therefore important that the iron ore potential of Ghana is showcased for eventual exploitation by potential investors to meet this enormous demand for the commodity in the industry globally. Ghana has three main iron deposits of potential industrial and commercial importance. They are: Shieni sedimentary iron ore (reserves: 1.270 X 106 metric tonnes), Pudo titaniferous-magnetiferous iron ore and the Opon-Mansi lateritic iron ore deposits. The Opon-Mansi iron ore deposit occurs in the Western region of Ghana. The ore deposits are located on top of the range of 15 hills, which extend over a distance of 24 km from Opon-valley, south of the Western region to Dunkwa. The area has an estimated 147 Mt of iron deposit, with Fe content of 52.5 per cent. This paper looks at the iron ore potential of Ghana and how it is capable of attracting potential investors to exploit this valuable mineral for global consumption.

Jan 1, 2007

By J P. Jona, S R. Poulson, C H. Gammons

Spatial and temporal trends in water chemistry in the acidic (pH ~2.6) Berkeley Pit lake, Butte, Montana, can be explained by a newly developed iron-cycling model. Key elements of this model include: subaqueous oxidation of pyrite and other metal sulfide minerals by dissolved ferric iron, producing Fe2+ as a by-product; re-oxidation of Fe2+ to Fe3+ in the epilimnion, assisted by A ferrooxidans; precipitation of secondary ferric minerals (schwertmannite, jarosite) in the epilimnion; and replenishment of the Fe3+ concentration of the hypolimnion by seasonal lake turnover and gravitational settling and re-dissolution of ferric precipitates. Pyrite oxidation rates were approximated by using published rate laws and information on the Fe3+ concentrations (~5 mmol) of the Berkeley Pit as a function of depth. The results indicate that subaqueous pyrite oxidation may be releasing as little as 6 + 106 or as much as 600 + 106 moles of H+ each year to the lake; the large range reflects uncertainty in calculation of the specific surface area of pyrite in the flooded pit. This helps to explain the observation that the pH and metal concentrations of the Berkeley Pit have not improved with time since mine flooding began in 1983. Vertical cycling of ferric iron in the pit lake permits pyrite oxidation to continue in deep water, even in the absence of dissolved oxygen. This hypothesis is supported by preliminary stable-isotope data.

Jan 1, 2003

By Bulters J, Sheppard I

Two blasthole density logging programmes have been conducted on the Mt Whaleback iron ore mine to evaluate the use of this type of logging as an aid to blast pattern design. The first programme also involved the setting up of a Density Test facility with which to calibrate the density probe. The programmes indicated that about 22-23 blastholes can be consistently logged per day at a cost of $1.30 per metre. Even though this is only half the rate required to log the average number of blastholes drilled daily on Mt Whaleback, testwork indicated that no significant loss of accuracy results if only half the holes in a pattern are logged. The major results of the programmes were: 1. The density range for black pyritic Shale is 2.2-2,9 g/cc. 2. The density range for soft to medium hard BIF is 2.1-3.0 g/cc. 3. The density range for hard BIF is 3.0-3.6 g/cc. 4. The front row blastholes show consistently lower densities than the main body holes due to blast damage. 5. A low density zone extending to a maximum depth of 6 m occurs at the top of most blastholes and results from blast damage from the bench above. These density results have been used to implement savings in drilling and blasting via pattern expansion and charge optimisation of blastholes. Eight ore

Jan 1, 1986

By Stewart C. A

The Northparkes copper-gold project is being developed in Central Western New South Wales approximately 30 km NNW of the town of Parkes and approximately 350 km west of Newcastle. The project is a joint venture between North Limited (80 per cent) and the Sumitomo Group (20 per cent). North is the manager. The basis of the project is three copper-gold orebodies, the northern two of which are being mined by conventional open cut methods with the third and largest orebody at the southern end of the lease to be mined by block caving. A fourth mineralised body has been identified in the centre of the lease. While further evaluation of this deposit is required it would appear to be amenable to block caving. Oxide caps of gold ore and copper-gold ore over-lie the two northern orebodies. Development commenced with the construction of a carbon-in-pulp (CIP) plant to treat the oxide gold ore. Construction of a flotation plant to treat oxide copper-gold ore and sulphide copper-gold ore is underway. When full-scale operation is achieved late in 1996 the plant will treat 5.0 million tonnes of ore per year of which 1.1 million tonnes will be open cut ore and 3.9 million tonnes will be block cave ore. In terms of annual ore tonnage the underground mine will be the largest metalliferous mine in New South Wales and the second largest in Australia.

Jan 1, 1995

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

By Lawson F

Arsenic-containing waste was dissolved into molten slags and the leaching behaviour of the quenched arsenic-doped slags (containing up to 2.3 wt per cent arsenic) was ascertained to evaluate the potential of this method as a means for arsenic disposal. The leaching behaviour was evaluated using acetic and sulphuric/nitric acid based solutions.From short-term (18 hour) leach tests, the amounts of arsenic in the leach solutions were found generally to decrease with an increase in the Fe(III)/Fe(total) ratio of the slag or an increase in pH of the leach solution. The amount of arsenic in solution increased with an increase in the slag basicity, the slag arsenic concentration or the surface area of the slag exposed to the leach solution. From longer term leach tests (up to 40 weeks) in the pH range 5 to 8, the arsenic remaining in the leach solution was believed to be controlled by sorption processes. The sorbent was an iron oxide-rich material which had the capacity to lower the arsenic concentration in the leach bottles to well below 1 ppm in some cases. At a leach solution pH over 9, the arsenic concentration in the solution increased with time, although the rate of solubilisation was much slower due to the high pH.Slags have the potential to stabilise arsenic and prevent it entering the environment provided attention is paid to the slag chemical composition and oxygen potential.

Jan 1, 1996

By S Gray

Based on the 2021 Volume 5 State of PlayTM mining survey of key executives and board members in the mining sector, the key responses to ‘Which of the following technologies will have the biggest impact on mining in the next 15 years?’, were ‘Sensing and Data’ followed by ‘AI and Analytics’. From the early 1970s it would have been unlikely to predict the level of sensing and automation introduced to the broad industrial sector. No better example is the automobile industry where the combination of technological advances and external drivers (such as emissions control) have driven an incredible rate of change. The introduction of sensing, data, AI, and automation in the mining industry is just ramping up. Until now our energy efficiency, environmental footprint, labour shortage, skills, and safety have not been challenged by stakeholders in the way we are seeing market forces develop today. In order to address these challenges, we need to look back to the automobile industry and learn their lessons to accelerate our application of digital capability, analysis, AI and automation This is critical, particularly as access to skilled human resources becomes more difficult. An example of how this can be achieved in a gold processing plant utilising the latest real-time sensing technologies is the ‘Carbon Scout’ developed by Curtin University, and OLGA developed by CSIRO, which are both online technologies, coupled together with Gekko’s ‘Neon’ digital platform to achieve a fully automated real-time gold processing system.

Aug 24, 2022

By P Dight

Increasing the strength of backfill has been the subject of much research. In the former Soviet Union most methods concentrated on the fill mixture including chemical additives, binder re-grinding, water electromagnetic activation and the use of vibration and turbulent activation. For the most part, this research has been confined to the laboratory where the results were not representative of field conditions. These methods also were directed at increasing the mass strength and were not specifically aimed at strengthening the fill where it may subsequently be exposed for instance on the side or underneath as it required for underhand cut and fill methods of mining. In the Republic of Armenia, a method of fill strengthening known as electro-activation has been adopted. The deposit it an epithermal gold deposit which to-date has been mined using underhand cut and fill with timber support. The backfill comprises cement and pumice placed in 2.5 m lifts. Central to the method of electro-activation is the placement of the electrodes in the stope in which the polarity and the electrical potential are changing during filling. The process promotes the binding of the fill layers, the bond to the side walls and to the adjacent fill. There is a significant increase in the compressive and tensile strength. The process has been used with beneficial effects on reinforced concrete and could be used in any mine utilising hardening fills.

Jan 1, 1998