Search Documents

By M Weeks

Melbourne Water Corporation, through the Pipelines Alliance, has commenced construction of a new drainage pipeline to provide additional flood protection within the Sandgate Avenue Main Drain catchment, in order to mitigate against the risk of flooding of Frankston’s central activity district (CAD).The project involves the construction of a 1550 m long, 2.5 m internal diameter tunnel, commencing upstream at the Monash University Peninsula Campus and traversing approximately west to the outlet located at Kananook Creek. The tunnel was excavated by a dual slurry-earth pressure balance tunnel boring machine (TBM), with the depth to tunnel crown ranging from 0.7 m to 14 m below the natural surface level. The TBM navigated 500 m radius curves, with a maximum drive length of 608 m. The tunnel lining consists of 2.5 m internal diameter, 250 mm thick reinforced concrete jacking pipe.The geotechnical conditions along the tunnel alignment consisted of mixed face ground conditions, predominately clay, with clayey sand and sandy clay and some sand deposits near Kananook Creek.This paper presents the challenges associated with the operation of the slurry separation plant during tunnel construction. In particular, the paper focuses the impact of slurry separation on tunnel advance rates, the lessons learnt during construction with regards to slurry separation and on the decision to adopt a dual slurry-earth pressure balance shield TBM. In addition this paper highlights the importance of having a thorough understanding of the slurry separation requirements on a slurry TBM project prior to selecting the necessary plant.

Mar 8, 2011

By Trois P

A fully instrumented and bench-mounted diamond drilling machine, purpose designed and built, has been used for investigating the effect of aqueous solutions of various chemical compounds when used as drilling fluids. The rocks investigated were andesite, basalt and granite, the chemical compounds were alkylamines, with various hydrocarbon chain lengths, aluminium chloride and dioxane. Rotation speed seems to be one of the major factors affecting the emergence of mechanochemical effects as the results obtained with aluminium chloride clearly indicate. Penetration rate is either unaf- fected or enhanced by the presence of certain compounds, such as aluminium chloride. On the other hand, penetration rate diminishes when the drilling fluid contains dioxane and exhibits an apparently unpredictable behaviour with alkylamine solutions, although it appears that an increase in hydrocarbon chain length usually equates to an increase in penetration 1. Full Professor, Mining and Mineral Dressing Department University of Cagliari - Italy 2. Associate Professor, Mining and Mineral Ikea- sing Department University of Cagliari û Italy rate. Rock texture seems to have a pronounced effect on test repeatability. With hexadecy- lamine acetate solutions in concentrations ranging from 10-5 to 5 .10-4 molò dm 3 and 41.88 radòs-1 rotation speed, 46 % increments in penetration rate of andesite were observed, with respect to water, whereas penetration rate decreased in basalt by as much as 60¦%o when a dioxane solution was used as drilling fluid. An interpretation of the observed effects is proposed in the light of current knowledge of solid state physics and physical Chemistry.

Jan 1, 1992

By Nilmani M, Fountain CR

Injection of gases into slag-melt mixtures produces various zones as a result of bubble formation and disintegration within the melt. The extent of these zones depends on the type of reactor used. When compared with ferrous processes, non ferrous processes are character- ised by large bubbles formed adjacent to the tuyeres, low flowrates and shallow tuyere sub- mergence. These features can result in a greater proportion of reaction occurring above the bath, more refractory wear and tuyere blockage with more splashing. The large bubble zone adjacent to the tuyeres has been investigated using the tech- niques of physical modelling, mathematical modelling and plant trials. Large bubble form- ation in physical models was recorded using a high speed camera and a rapid response pressure transducer coupled to an oscilloscope and data recorder. It was found that the bubble volume (Vb) could be correlated at low flowrates using the single bubble model Vb = 1.378 Q6/5 g-3/5 Deviations from this correlation occurred with increasing gas jet momentum. Plant trials were carried out on a copper converter at Mount Isa Mines during five different charges. Pressure measurements were made through the tuyeres during the slag blow and commencement of the copper blow. The power spectrum density showed that the dominant pulse amplitude occurred at a frequency of approximately 3 pulses/sec. Plant data from this and other converters were correlated using the same relationship as for physical modelling. De- viations occurred due to the state of the re- fractory, bath composition or bath circulation effects.

Jan 1, 1984

By J Northfield, L Neesham

The GRE46 Underground Project lies beneath the environmentally unique and culturally endowed shore of Lake Cowal. The ore body is open both along strike and at depth and is currently defined to a strike length of 1.5km and depth of 800m. The Warraga exploration decline commenced in March 2019 and represents the first stage of the Project, which is expected to underpin production at Cowal Gold Operations (CGO) for a period exceeding 10 years. Mining operations at Cowal commenced in 2005, following a period of over 20 years of exploration and permitting. In 2015 Evolution Mining (Cowal) Pty Limited (Evolution) acquired the operation from Barrick Gold Ltd (“Barrick”). Barrick had a life of mine plan that anticipated a cessation of operations in 2024 at a processing rate not exceeding 7.5 Mtpa. Evolution have grown the regional endowment considerably and have a currently approved mine life out to 2032 with a currently approved maximum processing rate of 9.8 Mtpa. This paper examines the history, current status and future path of one part of that plan, the GRE-46 Underground Project. Topics for discussion include discovery, Mineral Resource growth under different ownership philosophies, planning, permitting and commissioning of an exploration decline and bulk sampling project, and integration with the possible future mine. Environmental sensitivities affecting regulatory approvals, timeframes, technical challenges, opportunities and solutions are discussed, along with the path required to fast-track production from the existing 14Mt, 1.4Moz Mineral Resource while complying with the requirements of modern, responsible project development stewardship.

Mar 15, 2021

THE South Mine. owned by the Broken Hill South Limited, occupies mineral leases 7 and 8 on the Broken Hill lode. The ore reserves are 4,250,000 tons, and the ore hauled for the year ended June, 1930, was 387,000 tons, the total to date being 7,840,000.The mine, down to the 1070-ft. level, is naturally divided into two sections, the northern and southern ends. Ore extraction is practically completed in the northern end to this horizon, while the southern end is developed ready for a concentrated attack.Fig. 1 shows the state of the 8215-ft. level, after connection to the new shaft.The levels above and below to the 1070-ft. level are in a similar condition, while below the 1070-ft. level the stoping has been confined to the north end, but not completed. The south end on these levels is also partially developed.The ore at present is hauled up No. 1 shaft, which is centrally situated to the present workings. This shaft was put into use in 1909, and in 20 years has had approximately 5,000,000 tons of ore pulled through it.The company, having proved the existence of large ore-bodies in the southern end of the mine, decided to sink No. 7 shaft. This is a six-compartment frame-set shaft (see Fig. 2) equipped with two cages and two 5-ton skips, the remaining compartments being utilised for electric cables, pipes, and ladders. The surface arrangements will include a steel head frame, electric winders, and breaker station.

Jan 1, 1930

By Mishra BK, Agrawala S

The traditional method of scale-up uses the population-balance model. In particular, the selection function values for a material are determined in a laboratory mill and a variety of correlations are used to scale these values to plant scale mills. For example, the factor D2-5L (D-mill diameter, L-mill length) appears in many power correlations. The number of collisions is proportional to the number of balls (aD2L), the frequency of mill rotation ((x 1/4D-) and effectiveness of impact ((XD), which gives rise to the 'D2.5L' expression. However, what is lacking in this expression is that it does not throw light on the intensities of collisions. In other words, the collision intensities in both laboratory and plant scale mills are implied to be identical. This fact has been very limiting. Alternatively, the collision frequencies and intensity of impacts can be computed with the discrete element code. This code computes the motion and collision of each individual ball in the ball charge. Therefore the number of collisions and the fraction of collisions in the energy range Et, E2.òòE. (collision energy density) are calculated for a given mill size and operating conditions. Then, using the breakage function determined in drop-weight experiments, the evolution of size distribution is computed for a lab mill. The collision frequency and energy density for larger mill sizes are shown. The fundamental theory outlined for the calculation of size distribution is equally applicable for the large mill, which is the basis for scale-up.

Jan 1, 1993

By Blaskett K. S

The physical properties of monazite and the minerals with which it is associated in east coast beach sands are studied and discussed. Possible means for improving recovery are examined. In particular, it is suggested that the practice of splitting the heavy mineral concentrate into two parts as a preliminary to treatment in separate "rutile" and "zircon" mills can be modified in a simple fashion by the addition of an extra magnetic separation stage so as to aid monazite recovery.INTRODUCTIONBeach sand deposits on the east coast of Australia are a major source of rutile and zircon, and supply 80 per cent or more of world requirements. The deposits also contain a small amount of monazite, averaging about 0.5 per cent of the total heavy minerals. Yet despite a steady price in recent years of £150-160 per ton, monazite production has remained relatively small.On the basis of rutiIe production, potential monazite production on the east coast was about 1,500 tons in 1956, but only 102 tons of high-grade concentrate was produced. The main deterrent to increased production has probably been the capital cost of the necessary equipment. Separate electrostatic and magnetic equipment and separate table concentration and drying constitute a considerable outlay for a by-product contributing 4 to 5 per cent of the revenue from rutiIe.It is the purpose of this paper to discuss monazite concentration generally and to suggest modifications to flowsheets, which may facilitate monazite production while maintaining the main objective, simple and cheap means for maximum rutile production.

Jan 1, 1958

By M Watts, P Lindsay

Herbert Stream, a tributary of the Waimangaroa River on the Stockton Plateau, has elevated metal concentrations and low pH characteristic of acid mine drainage (AMD). Dissolved aluminium concentrations average 8.3 ppm, iron 1.4 ppm, manganese 0.69 ppm, and zinc 0.12 ppm and pH ranges from 2.8 to 3.2. Flow rates range from 2.3 to 26.6 L/s with an average of 5.3 L/s. To determine the effectiveness of different treatment strategies, a small amount of the AMD was diverted through three small-scale passive AMD remediation systems over an eight month period. These included a reducing and alkalinity producing system (RAPS), a limestone leaching bed (LLB), and an open limestone channel (OLC). Both the RAPS and the LLB performed well, effectively removing metals and restoring pH. The RAPS lowered aluminium concentrations by up to 99%, iron 97%, manganese 95%, and zinc 80% and the LLB lowered aluminium concentrations by up to 99%, iron 99%, manganese 92%, and zinc 91%. The pH was restored to between 6.4 and 7.4 by the RAPS and to between 7.3 and 7.9 by the LLB. The OLC performed well as long as the residence time was similar to that of the other treatment systems. OLC removal rates for aluminium was up to 99%, iron 94%, and manganese 21%, and the pH was restored up to 5.6. Due to its simplicity and effectiveness, it is proposed the LLB be constructed to fullscale size to treat the entire Herbert Stream.

Jan 1, 2007

Development of the Davcra flotation cell has continued over the past seven years. Preliminary testwork on single cells has now been extended to a com- plete Davcra flotation circuit, to cells ranging from 5 to 400 tons per hour capacity and to cells operating on a variety of materials. Operation of both test and production units has shown the Davcra cell to be competitive with conventional flotation machines. It offers a lower capital cost installation than conventional cells and in addition has a number of. operating advantages, particularly in its adaptability to automatic control.'

Jan 1, 1971

By Grady PO

The longwall panels at Clarence Colliery have experienced intermittent sudden weightings on the face that have caused some production delays. These weightings have typically been more severe on the wider faces. A program of surface subsidence and extensometer monitoring was undertaken above Longwalls 4 and 5 to investigate the behaviour of the overburden strata during longwall extraction on two faces of different widths.The monitoring indicated that a dome shaped zone of large downward movement extends up into the overburden strata to a height equal to about the panel width.

Jan 1, 1998

By Just GD, Phillips R

The application of high pressure water jet technology to the drilling of longholes in coal has resulted in the development of a system currently capable of drilling to lengths greater than 200m. Field tests at the German Creek Mine have demonstrated directional control of the holes within a 0.5m section of the seam. Initial application of the technique at the German Creek operations is for drilling methane drainage holes. These developments, in three stages, result from support by the National Energy Research Development and Demonstration Council

Jan 1, 1991

This paper describes a mine truck hauling process called "Truck Jigging" which is currently the subject of a process patent application.The investigation explores the production and cost advantages of using the potential energy available in a descending haul truck to assist in elevating an ascending vehicle. Applications are studied for both strip cut mines and open pit operations. Various mechanical connections between the two vehicles are considered, based on a pulley mounted rope system. Fifteen year operating cost estimates show savings of up to 26.5 percent over conventional mine truck operations.

Jan 1, 1989

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal.

Jan 1, 1989

A minimum target of economic growth in Australia has been set at 5% per annum growth in G.N.P. at constant prices (Vernon Committee). 2. The core of the problem of sustaining steady growth at this or a similar rate is to ensure regular flows of investment. This sustains productivity, helps to control balance of payments pressures, and to check inflation. 3. The regular intake of human and physical resources, in conjunction with intensive capital development involving finance, technology and management, is basic to sustaining the growth rate and ensuring rising standards of living.

Jan 1, 1971

By Brown D. N, Troth D. A

Large blast furnaces demand high standards of preparation of feed materials which must meet tight specifications of chemical and physical quality. Measurement of these factors must be expeditious but the nature of the coke, sinter, ores and fluxes and the large tonnages involved requires substantial mechanical sampling plant. The equipment, its operations, and its problems, associated with the 5000 t.p.d. No.5 blast furnace at Australian Iron and Steel Pty. Ltd., Port Kembla, are described and the efficacy of chemical blending achieved in the ore blending yards and sintering operation, is reported.

Jan 1, 1976

By M Skead, H Michael, R Chase, A Davidson

Ashanti Goldfields CompanyÆs (AshantiÆs) most recent development is the Geita Project in the Lake Victoria Goldfield of NW Tanzania. It comprises six distinct gold deposits within two mineralised trends: Nyankanga, Lone Cone, Geita Hill (Geita trend) and Matandani, Kukuluma and Area 3 West (Kukuluma trend). Between 1936 and 1966, the Geita area produced an estimated 5.5 M tonnes of ore from five underground deposits at an average recovered grade of 5.3 g/t. The discovery of Nyankanga was made by Ashanti in 1996 from RAB drilling of a +100 ppb Au anomaly in laterite soil above ferricrete cover. The Kukuluma trend was discovered by SAMAX Resources (taken over by Ashanti in 1998) between 1996 and 1997 from RC drilling of a +80 ppb Au laterite soil anomaly. Oxide facies banded iron formation (BIF) of the Upper Nyanzian System forms prominent topographic ridges and is the dominant host lithology for gold mineralisation. The ridges are flanked by felsic tuff units which lie stratigraphically above. Syn-genetic lamprophyre (vogesite) and post-genetic felsic dykes are also seen in the Geita trend. At Nyankanga a granodiorite-diorite suite has intruded as dykes and sills into BIF from a plug centred on a WNW fault and has produced wallrock alteration assemblages similar to those seen in Cu-porphyry systems (potassic, propylitic, etc) as well as sulphide and gold deposition. However, the main ore-grade mineralisation (as in the rest of the Geita trend) is controlled by low-to-medium angle structures dipping north-west and north with numerous splays in the hanging wall. High-grade shoots at Nyankanga plunge to the west and to the north-west, being lithologically and fault-controlled respectively. At Geita Hill the higher grade shoots are controlled by fold noses in BIF dipping to the north. Free gold occurs within fractures of sulphides. The deposits of Kukuluma and Matandani occur on an ancient (possibly Cretaceous) erosional plateau and are related to two WNW to NW trending shear zones, discordant to the local strike of the BIF sequence. Complete oxidation occurs up to 120 m depth and there is a strong supergene component to the gold distribution. Primary gold mineralisation is divisible into two distinct assemblages: arsenopyriteûpyrrhotiteûmagnetiteûchlorite associated with brecciated cherts and pyrite associated with shaley banded ironstones. Area 3W is most likely the fault-displaced extension of the same mineralised trend and comprises thin, intermittent zones of high-grade gold mineralisation occurring adjacent to a ridge in banded cherts and minor BIF. Current resources (measured, indicated and inferred) for the project are estimated at 89.24 Mt at an average grade of 4.17 g/t (11.97 Moz of contained gold) at a 1.0 g/t cut-off grade. Of this 9.83 Moz is within the Geita trend and 2.14 Moz is within the Kukuluma trend. A resource of 2.74 Moz is from an inferred resource at depth at Nyankanga where the viability of an underground operation is being studied. Proven and probable reserves are 49.77 Mt @ 3.46 g/t (5.54 Moz) based on a $325/oz gold price providing a mine life of ten years at an average production rate of 500 000 oz per year. Reserve estimation was carried out using mineable polygons to select resource blocks based on a series of mining and costs parameters. In addition key cost parameters were tested to provide sensitivities for pit optimisations and pathfinders for negotiations with suppliers and contractors. Construction began in March 1999 and first gold is expected to be poured in the second-quarter 2000.

Jan 1, 2000

By M M. Collisson

The Synthetic Rutile (SR) plant operations, North Capel, produce electrostatic precipitator (ESP) fume and kiln scrubber residue. Typically ESP contains about 18 per cent Ti, 13 per cent Fe, 0.5 per cent Mn, eight per cent Si, six per cent Al, 16 per cent C, 0.9 per cent Zn, 0.6 per cent Pb, 300 ppm As, 300 ppm Cr and 5 ppm Cd. These wastes are held in a storage dam together with neutralised acid effluent (AE) liquor. A project was initiated to treat the fume and produce a benign residue that could be delivered to landfill, reducing dam space storage. Plant AE, containing free acid (9 - 14 g/L), Fe (6 - 7 g/L) and Mn (1 g/L), was used to leach ESP. The degree of extraction achieved for various elements include about 20 per cent Zn, almost 50 per cent As, five per cent Al, 0.4 per cent Pb and 15 per cent Cd. Extraction was most effective at pH The residue from AE leaching still contained Pb. TCLP tests of the leach residue produced Pb extraction significantly higher than the 0.1 ppm stipulated by Class 2 landfill guidelines. Other elements (eg As, Cd, Cr) successfully met the limits. Further leaching of the residue with EDTA extracted up to 65 per cent of Pb content. TCLP tests on treated residue showed Pb leaching potential of Lead was removed from the leach circuit as the sulphate by acidification of EDTA leach liquor, allowing EDTA to be recycled. The study showed that one waste stream can be used to treat another and help reduce plant waste.

Jan 1, 2001

By Y Zhang, Z Zhao

The green production of the steelmaking process has urgent requirements for fluorine-free fluxes. In this article, a new solid waste-based slagging flux was applied in the external dephosphorisation test of low silicon hot metal to replace the traditional fluorite-lime dephosphorisation slag. The results showed that under laboratory conditions, the new flux was utilised for smelting low-silicon molten iron with a phosphorus content of 0.10~0.13 wt per cent, the temperature of the molten iron was 1350°C and the slag amount was controlled at 2 per cent. Within ten minutes of smelting, the dephosphorisation rate of the molten iron reached more than 50 per cent. When making slag with new flux, the slag melting time was about 40 seconds and the P2O5 content in the final slag was higher than 8 wt per cent. In the industrial test of a 150 t molten iron ladle, under the same molten iron conditions, an out-of-furnace dephosphorisation test was conducted in the Kambara Reactor (KR) process. The flux material consumption per ton of steel was 8~10 kg. Within 15 minutes of smelting, the dephosphorisation rate of the molten iron was about 30 per cent. During flux slag making, the slag melting time was about three minutes and the P2O5 content in the final slag was higher than 6 wt per cent. This new solid waste-based flux has significant cost advantages and outof- furnace dephosphorisation effects and is expected to become the benchmark for a new generation of fluorine-free steelmaking fluxes.

Aug 21, 2024

By G McSpadden

At September 2001 the beneficiation plant at BHP Billiton Iron OreÆs Mt Whaleback mine is set to treat 9.5 million tonnes per annum (Mtpa) of iron ore, 40 per cent better than original design. This paper describes the steps, decision-making processes and innovations used to increase capacity at minimum cost. The plant was designed in 1979 to operate at 1133 t/h for 6000 hours per annum, treating 6.8 Mtpa. Sufficient suitable contact ore was unavailable and feed was finer than planned. The plant was designed with minimum surge capacity between multiple process units. It had never reached design capacity. In 1993 a study by Fluor Daniel to treat increased tonnage resulted in modifications to improve plant operations. Efforts to expand production by increasing reliability did not achieve the desired capacity. NJ Morrow (Pty) Ltd (NJM) conducted a technical audit in 1996 with process evaluation by Mineral Processors. Replacement of operator interface and PLC logic in 1997 made plant operation and diagnosis easier. Involving operators in logic development enhanced their plant knowledge. Fluor Daniel Simulation developed a simulation model of the process. Mineral Processors and NJM reviewed the model findings, recommended metallurgical improvements and developed preliminary designs and costs. BHP Engineering produced a detailed design with a cost estimate of $A34 million. After analysis and revision of the design, a $A10.4 million upgrade to 8.5 Mtpa was carried out. Detailed modifications to the process units, particularly the HM drum plant, allowed significantly higher capacities and improved metallurgical performance. The target capacity was achieved in June 2001. Further modifications are progressing to treat lower-grade ores.

Jan 1, 2002

By Palmer C. G, Rowe P. G

Ore handling improvements at Mount Isa Mines Limited were necessary to keep abreast of technological advances in all phases of sublevel stoping practice.In the early 1930s an efficient ore handling system was in operation.However in 1936 excessive water encountered in deepening the hoisting shaft necessitated the sinking of a second hoisting shaft. Financial difficulties prevented abandoning the original shaft and surface ore handling and crushing facilities, so ore was transferred underground and underground crushing deferred. It was not until 1951 Jhat multilevel crushing permitted increased efficiency in the handling of ore from stopes. Ore was then hoisted in one shaft and transferred on the surface by conveyor belt to a new crushing plant.In 1956 a planned production increase from 5,000 to 11,000 tons per mining day made possible further improvements in ore handling. Larger equipment was installed and existing equipment modified to capacitate the handling of larger sized ore at increased daily tonnages.INTRODUCTIONThe intensive exploratory programme commenced in 1954 disclosed large reserves of both lead and copper ores and in 1956 an expansion programme was initiated to increase production from 5,000 to 11,000 tons per mining day. The increased tonnage would result in decreased costs per ton and further cost reductions would result from increased mechanisation underground. The combined effect would permit larger tonnages of lower grade ores to be included in ore reserves. To achieve both cost reduction and the scheduled production increase, improvement in ore handling was of vital importance.For efficient and low cost sublevel stoping it is necessary to maintain an economic balance between...

Jan 1, 1961