Search Documents

By N. F. Schulz, H. A. Lex, J. D. Zetterstrom

A green ball of iron ore faces many perils from the time it is formed until it finally emerges from the pelletizing furnace as a hardened pellet. For instance, if the rate of heat transfer into a ball is sufficient to produce vapor from either the free or combined water more rapidly than it can escape at a tolerable pressure, the ball may split, spall, or even explode, a failure commonly known as decrepitation. To avoid such failures, one must either limit the rate of heat transfer during the drying and preheating stages, at the expense of production rates, or improve the decrepitation resistance of the green balls. The latter remedy may often be accomplished through changes in ore preparation, balling procedures, or the judicious use of binders or other additives. INTRODUCTION Pelletization has become established as an especially desirable method for the agglomeration of fine taconite concentrates and it promises to be equally satisfactory for improving the physical structures of certain natural ores. A high-quality pelletized iron ore consists of uniformly sized spheres, usually about 1/2-in. diam, which are strong enough to resist abrasion and breakage during handling and which reduce well without disintegration in the blast furnace. The unfired agglomerates, "green balls", are subject to several destructive effects that must be avoided or minimized if a high-quality product is to be obtained by pelletization. Among these are abrasion and impact deformation or breakage during handling of the wet green balls, deformation and breakage by compressive forces in the bed of ore in the pel-letizing furnace, decrepitation during drying and preheating, wind erosion, and radial cracking at firing temperatures. Moisture condensation from the warm saturated gases downstream from the drying zone on wet, cool balls may cause bed collapse if it becomes excessive. Decrepitation is defined as the sudden disintegration of green balls, usually with an audible pop, that occurs when they are heated too rapidly during the drying or preheating stages of the pelletization process. The extent of ball disintegration may vary from merely splitting off a small fragment to almost total disintegration into the original ore particles making up the ball. Such ball destruction results in a decreased yield of pellets, and the fragments, which also tend to interfere by obstructing the gas flow through the bed, must eventually be screened from the fired product and recycled. The closely related type of ball failure that sometimes occurs during the high temperature firing stage, resulting in radial cracks without fragmentation, was not considered to be decrepitation for the purpose of this investigation. Failure by decrepitation is not usually a serious problem in the pelletization of taconite concentrates. The problem is significant, however, in the pelletization of some natural ores, especially those containing hydrous iron oxides. In some instances, economicd production rates cannot be maintained if the drying and preheating rates are slowed down enough to avoid decrepitation. OBJECTIVES This investigation was undertaken to: (1) Develop a practical laboratory means for quantitatively measuring the tendency for green balls to decrepitate in iron ore pelletizing furnaces, and (2) Investigate the causes and cures of ball decrepitation. MATERIALS Two iron ores were used in the work reported here: a taconite concentrate at 90% minus 325 mesh, containing 65.0% Fe, 8.4% SiO2, and no loss-on-ignition; and a crude oxidized ore at 54% minus 325 mesh, containing 59.1% Fe, 3.6% SiO2, 1.1% A12O3, and 9.5% loss-on-ignition. For a special test of effect of particle size distribution on decrepitation, two other

Jan 1, 1967

By E. L. Jr. Spain

This study was undertaken primarily to determine the reasons for certain varia-tions in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates it some cases exhibited marked differences in specific gravity, crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents.

Jan 1, 1937

By L. Adler

A relatively simple and effective technique is proposed to deal with the failure of geologic masses containing weakness planes. This technique, termed irextended" rupture envelope, provides a means to clearly distinguish rock and soil from fractured rock and, on a theoretical level, considers a matrix-inclusion system. It may also constitute the link between Mohr's and Griffith's failure theories. Included in the article are five sample problems concerning site location, structural design, strengthening the plane of weakness, changing the magnitudes of major and minor principal stresses and changing the orientations of major and minor principal stresses. Engineers trying to solve design problems in rock and soil mechanics have often assumed an iso-tropic and homogeneous medium. For naturally occurring geologic masses this assumption has always been viewed with regret. The following analysis which deals with the effects of plane anisotropy on failure presents a solution to this. The planes of weakness are joints, faults, bedding planes, fracture and cleavage (natural and induced), foliation and schistosity. The physical properties of these weakness planes include an undulating surface, frictional resistance, discontinuous extent, filling material, tightness and presence of water to cause a hydrostatic pore pressure. All of these properties relating to failure can be summarized in Mohr's rupture envelope for the plane of weakness. This, along with the geometrical orientation, strike and dip, of the plane of weakness produces what is termed an irextended" rupture envelope. MOHR'S STRESS CIRCLE AND RUPTURE ENVELOPE The significant features of these concepts are listed below.' 1) A point on the u - r coordinate plane represents the normal and tangential stress components on a reference area in the material. This area can have any orientation. (Fig. la)

Jan 1, 1963

By Allen L. Hatch

A survey of all phases of the world's lead and zinc production in 1968 from ore through to refined metal was conducted by sending questionnaires to individual companies ad the results of this survey are tabulated at the end of the paper. The paper goes on to review changes in the geographical distribution of the world's lead and zinc mine and metal production and in the trading patterns of raw materials, present and future utilization of metal production capacity, developments in metal smelting and refining processes and the growing importance of marketing, product development and research in the 1950's and 1960's.

Jan 1, 1970

By C. H. Mathewson

Discussion of the paper of C. H. MATHEWSON and ARTHUR PHILLIPS, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 1 to 50. ZAY JEFFRIES, Cleveland, Ohio (communication to the Secretary*).¬The authors are to be congratulated for this interesting and valuable contribution. The paper as a whole shows very careful experimentation coupled with rare judgment in drawing conclusions. I have been working along similar lines for the last two years with other metals and alloys. In a short conversation with Dr. Mathewson about July 1, 1915, he mentioned the fact that different degrees of cold work greatly affect the temperature of recrystallization on annealing, Later I determined the recrystallization temperatures of iron, mild steel, and copper, with different degrees of cold work and found that the greater the degree of cold work, the lower the temperature of recrystallization on annealing. In the course of these experiments, I conceived practically the same ideas regarding the reasons for recrystallization as those advanced in the article under discussion. After a metal has been reduced by cold work to about one-fourth of its original area, the differences in orientation of different parts of a given grain can be seen plainly at a magnification of about 1,000 diameters. It is interesting to note that in Fig. A, Plate I, the lines of deformation are not parallel. For example,. in the large grain at the lower left corner of the micrograph, if the lines of deformation about 3g in. from the left edge are continued in a straight line, this line will intersect a straight line drawn as a continuation of the lines of deformation on the extreme right of the grain, at an angle of about 20°. Similarly, if the lines of deformation at the extremities of the large grain in the right central portion of the micrograph are extended, the lines intersect at an angle of about 35°. The individual lines of deformation are not straight. In some of these the parts of the broken lines intersect at angles as great as 15°.

Jan 5, 1916

By John V. Beall

Copper production in the. United States in 1972 amounted to 1,658,000 tons according to the USBM. This figure is up over 1971 but falls below 1970 production of 1,719,101 tons. This report is essentially about the status of copper mining operations in the U.S. and is an update and expansion of the report "Southwest Copper-A Position Survey" published in [A=], October 1965. At that time, the trend was toward using larger equipment to mine lower grade ore and toward the expansion of dump leaching practice. That trend continues today but, it is overlain by intensive activity to comply with existing environ¬mental legislation and uncertainty over proposed revisions of venerable laws governing mining. In the U.S. today there is, practically speaking, no excess smelting capacity so that expansion of copper production through the startup of new mines is inhibited. Owners of a large undeveloped orebody would have to decide before going into production whether to sell the concentrates offshore, which has many problems, whether to try one of several unproved chemical processes for producing refined metal from concentrates or embarking on the construction of a traditional pyrometallurgical plant in the face of considerable uncertainty over the pollution standards that eventually must be met. The situation is such that not only is the present rate of U.S. copper production threatened but the ability to meet projected increased demand in the years ahead may have been severely retarded.

Jan 4, 1973

By E. C. Dominguez

INTRODUCTION The first commercial plant in the world to successfully produce pellets from manganese ore fines is the ICOMI pelletizing facility in northern Brazil. The main purpose of this paper is to describe the manganese pelletizing process that was developed through a cooperative R & D program by the Bethlehem Steel Corporation and ICOMI, i.e., Industria e Commercio de Minerios, S. A. The process combines heavy- media and gravity separation, reduction roasting, magnetic separation, and pelletizing on a straight-grate indurating machine. It produces high-grade manganese pellets from reviously unsalable low-grade ore fines at a rate of 20,000 tonnes (1) per month. The physical properties of the manganese pellets are comparable to those of iron ore pellets. The pelletizing plant, built at a cost of about 18 million dollars, is part of an ICOMI complex that includes manganese ore mining, an ore-washing plant, and railroad and port facilities, as well as two town sites. These two towns, one at the mine and the other at the port, each with complete community services, were built by ICOMI to serve the needs of over 1500 employees that operate the industrial complex. To give an idea of the magnitude of the investment represented by this complex, the cost up to 1957 to develop the mine and supporting services and social infrastructure was over 100 million dollars. It should be borne in mind that the above capital cost figures are in dollars of the years during which the respective projects were initiated and completed.

Jan 1, 1977

Jan 1, 1898

By J. Poijärvi, J. Rastas

Recently, when increasing attention has been paid to mercury for environmental reasons, the interest of several plants is directed to the removal of mercury from roaster and smelter gases. When Outokumpu Oy built its zinc plant at Kokkola in 1969, intensive development work was started to find an efficient and economic method for mercury removal from roaster gases. A process was developed, after laboratory research and pilot plant tests, to eliminate and completely recover mercury from the roaster gases. The process was commissioned in 1970. The behaviour of mercury in the roasting process and several possible methods of removing it from gases are discussed in this paper. Theoretical investigations and empirical tests show that the removal of elemental mercury from gases by sulphatization is very efficient. Further, it is stated how the technical process was built on this idea. The zinc sulphide concentrates contain small quantities of selenium, chlorine and fluorine. The role of selenium in the process is described. Similarly, the behaviour of chlorine and fluorine in the roasting, sulphatizing and scrubbing units has been discussed. Finally, the recovery of purified mercury and selenium from the precipitates is described.

Jan 1, 1973

Polluted air and water, despoiled land and excessive noise are the unwelcome results of the population growth and a rising standard of living. The consumption of goods and services, including metal products and minerals, by all people is increasing so rapidly that civilization is in danger of destroying the environment in which it lives. This is true because every human activity affects the environment, whether it is air, water or land. While E. F. Osborn, director, U.S. Bureau of Mines, says . . . "some members of the mineral industry are reluctant to recognize environmental demands" . . . William T. Pecora Under Secretary of the U.S. Department of the Interior.. . says that, "to maintain levels of resource development and environmental quality needed to satisfy our affluence, we must trade off values rather than turn off troublesome operations." What it seems to boil down to is how much control of its operations is the mineral industry willing to accept-internal policing or strict government control? The answer lies in how well the mineral industry maintains a balance between mineral development and environmental quality.

Jan 1, 1971

By John Birkinbine

In the preparation of the paper upon " The Operation of Warwick Furnace, Pennsylvania, from August 27, 1880, to September 1,1885," presented at the Pittsburgh meeting, I purposely refrained from offering theories to explain the peculiarities of furnace operation, on the ground that it was better for those actively engaged in blast-furnace management to present records of operations, than for one more directly interested in blast-furnace engineering and construction to venture upon the sea of speculation as to causes. The manager of an iron-works naturally feels that he knows as much about his particular furnace or furnaces as any one else, and as Mr. Cook, after his close attention to and study of the Warwick furnace, was at that time unwilling to present theories, I felt a disinclination to assume more acumen than the manager.

Jan 1, 1887

Jan 1, 1897

By H. L. Gilbert, C. Travis Anderson, W. J. Kroll

IN a previous paper,1 the use of a split graphite tube resistor as a heater element for high-temperature furnaces has been described. The principal advantages of this type of construction are: I. The quadruple resistance or voltage compared with the top-bottom clamp resistor furnace. 2. Free expansion of the resistor. 3. The ease of protection from oxidation by air. 4. The firmness by which it may be held in the compact split clamp. This construction appeared to be well adapted for the fusion of high melting metals which require fusion in a vacuum. Zirconium metal had previously been melted at the Albany Laboratory of the Bureau of Mines in a vacuum arc furnace on a water-cooled plate, using a movable tungsten top electrode.2 When larger furnace capacities were desired, this type of construction proved to have its limitations as the largest tungsten rods available were about 7/8in. in diameter. The supply of direct current of high amperage for producing the . desired arc characteristics was also not available. Considerable difficulty was also found in compensating the atmospheric pressure on the flexible tubing of the movable electrode, at the same time keeping its movement sufficiently free to enable the striking of an arc on any part of the metal briquet. Among the various materials used for the electrodes in conducting experiments in the vacuum arc furnace was graphite. It was found that zirconium fused in a graphite cup with a carbon arc was contaminated to only 0.2 pct carbon. It was therefore decided to melt zirconium directly in graphite crucibles. A high-frequency furnace was first used in the attempt to melt the zirconium in graphite crucibles. The high-frequency heating coil was placed outside a silica tube which was evacuated by means of an oil diffusion pump backed up by a mechanical pump. The graphite crucible was thoroughly degassed at 1900°C before use. Considerable difficulty was experienced in operating at such temperatures in vacuo because, as shown by Zintl,3 carbon vapor formed and reacted with silica according to the reaction: Si02 + C = SiO + CO. The silicon monoxide which is volatile at these high temperatures reacted with the zirconium, thereby contaminating it with silicon and oxygen. The presence of carbon monoxide was detected by means of a gas discharge tube placed in the vacuum system as indicated by the pale blue glow of the tube as soon as carbon vapor started to react with the hot silica. The reaction between the carbon vapor and hot silica was avoided by the use of split cylindrical molybdenum shields which were inserted between the graphite crucible

Jan 1, 1948

By Mayumi Someno, Kazuhiro Goto, Masahiro Kawakami

The apparent rates of decarburization of liquid alloys of Fe-C, Fe-C-S, Ni-C, and Co-C systems and the rate of oxidation of solid graphite with pure carbon dioxide gas and with gas mixtures of carbon monoxide and carbon dioxide have been measured in the temperature range of 1000° to 1600°C. The cotnposition of carbon dioxide and carbon monoxide gas at the reaction surface has been measured by oxygen concentration cells with the ZrO,-CaO solid electrolyte. 1) The apparent rates of the carbon removal are essentially the same for all the cases of solid graphite, Fe-C, Fe-C-S, Ni-C, and Co-C systems under the same experimental conditions. 2) The apparent rates are independent of the carbon content in the high carbon concentration range but very much affected by the flow rate and the gas composition of the CO-CO2 reactant gas mixture. The ratio of the gas consumed by the reaction to the total quantity of the supplied gas is very large under the present experi~nental conditions. 3) There is a concentration gradient of' carbon dioxide in the vicinity of the reaction surface and the content of CO, becomes extremely small at the reaction surface. 4) A large time fluc-tuation of the gas composition was observed. This jluctuation implies the presence of unstable flow in the gas phase in the vicinity of the reaction surface. THE decarburization of molten steel by an oxidizing gas or by slag may be one of the most important chemical reactions in steelmaking processes. Nevertheless, the kinetics of this heterogeneous chemical reaction do not seem to be well-solved even with the previous studies. Although the conditions for the reaction in steelmaking processes are quite different from those in the laboratory scale, some critical experiments may give information on the mechanism of the decarburization. From the previous work,'-' it is known that the rate of the decarburization is independent of the carbon content in liquid iron with more than about 0.2 wt pct C when the oxidizing gases are supplied to the surface of liquid Fe-C alloys on a laboratory scale. Two rate-controlling steps have been proposed for the decarburization of liquid iron with the high carbon content: one is the surface reaction control proposed by Swisher and Turkdogan;' the other is that the rate is controlled by the gaseous diffusion through the gaseous stagnant layer. proposed by Baker. Warner, and Jenkins.7 and also by .Ito and Sano.2 In the present study, some experiments have been carried out for the evaluation of these rate-controlling steps in the decarburization of liquid iron with high carbon content. The apparent rate of decarburization of liquid iron has been compared with the rates of carbon removal of liquid Ni-C, Co-C, and solid graphite under the same experimental conditions. The composition of carbon dioxide and carbon monoxide gas at the reaction surface has been measured by oxygen concentration cells. I) EXPERIMENTAL PROCEDURE Fig. 1 shows the schematic diagram of the reaction chamber. Solid graphite and liquid metals were contained in an alumina or magnesia crucible of 32 mm ID and 35 mm in height. The samples were heated by high-frequency induction and the temperature was measured by the calibrated optical pyrometer. The temperature was held constant to within 10°C. The re-actant gases were supplied to the surface of the samples through the quartz tube of 8.0 mm ID. The distance from the end of the quartz tube to the surface was 20 mm. The block of high-purity graphite was cut and shaped to the inner profile of the crucible. The height of the shaped graphite was 18 mm, which corresponded to the depth of the liquid iron of 100 g. About 100 g of Fe-C alloy (4.20 to 4.40 pct C), Ni-C alloy (1.84 pct C), Co-C alloy (1.85 pct C), and Fe-C-s alloy (4.35 pct c, 0.5 or 1.0 pct S) were melted in the crucible. The reactant gases were pure CO, and gas mixtures of CO-CO,: the flow rates were controlled by capillary flowmeters with bleeders.

Jan 1, 1970

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By H. F. Yancey, O. L. Furse

For several years the Bureau of Mines at its Northwest Experiment Station, in cooperation with the Mines Department. of the University of Washington, has been studying the breakage and degradation of coal. The first phase of the study was devoted to the determination of the friability of many coals of various ranks and comparison of various methods for estimating friability.' A study of the relative ease or difficulty with which various coals are reduced to the fine size required for use as pulverized fuel followed the completion of this work. Baltzer and Hudson2 list twelve research organizations in the United States, two in England, one in Germany and one in Canada that are reported to be engaged on this problem; showing the general appreciation of the need for a simple method of estimating the grindability of different coals. Hardgrove,3 ho has advanced a method for estimating grindability, points out that pulverizer tests of different coals are incomplete and unsatisfactory. He compares such tests to that of a boiler test made without knowledge of the calorific value of the coal. Frisch arid Holder4 also stress the same point. They state that,

Jan 1, 1934

America.-Foreman, J. T. Ashland.-Sturdevant, J. C. AItalIa. Henderson, R. M. Bessemer.-Ball, E. M. Maschmeyer, W. L. McKenzie, W. C., Jr. Birmingham.-Abbott, C. E. Aldrich, T. H. Aldrich, T. H., Jr Aufderhaar, H. C. Berg, H. A. Blair, C. S. Bush, M. W. Clark, G. H.

Jan 1, 1923

By J. A. Barr

Tennessee phosphates are commercially divided into three varieties: Brown, Blue, and White.

Jan 1, 1915

Teamwork: The famous first sentence of an essay en- titled Aphorisms, by Hippocrates, is as follows: "Life is short, the Art long, opportunity fleeting, experience treacherous, judgment difficult." The future of science does not depend so much on the number of scientists or the number of colleges, but rather on the individual qualities and the degree of perfection of a limited group of leading scientists and colleges. These are individual factors which require inherent talent which in turn is a condition evolved after generations of culture. Thus, very elaborate higher education for indiscriminate masses of humanity or students may not necessarily show the expected results. In other words, it is possible that higher specialized education should be given only to the few talented individuals, and their capacity and worth should be judged by as highly qualified and talented teachers. Quality is the greatest of all competitive aids. An essential qualification that must be possessed by a quality mineral industries college is a high caliber teaching staff, for the mineral sciences will advance in the coming years only if the leading minds of today are made avail- able as the mental springboards for our scientists of tomorrow. Mineral industries schools are finding it increasingly difficult to maintain a high caliber staff of instructors and administrators in competition with private business and governmental demands for similar

Jan 1, 1950

By C. E. Abbott

THE Birmingham district, Alabama, is distinctive in the proximity to one another of its deposits of iron ore, coal and flux. These three basic requisites for the making of iron and steel are found within a radius of 10 miles. Both dolomite and limestone are produced, the former for blast-furnace flux and the latter for basic open-hearth operations. The Tennessee Coal, Iron and Railroad Co., a subsidiary of the United States Steel Corporation, operates a limestone mine at Muscoda, near Bessemer, 12 miles southwest of Birmingham, served by its own railroad transportation system. The mine has a capacity of 130 tons per hour. Average analyses of a recent month's production are as follows: Fe2O3 Si02 A12O3 CAC03 MGCO Lump, per cent 0.51 0.22 98.63 0.14 Crushed and washed, percent 0.70 0.26 98.36 0.18 Lump stone, 2 1/2 to 7 1/2 in., is used in open-hearth operations at Fairfield Steel Works. Fine crushed and washed stone, 1 ¼ to 0.063 in., is calcined at the, lime-burning plant and used for lime charges at the Ensley open hearths.

Jan 1, 1936