Search Documents

By R. Haynes

ON the basis of compositional changes of a phase observed in a eutectoid Cu-Al alloy1 it has been suggested that mechanisms for the decomposition of the ß phase proposed by earlier workers2-5 were incorrect. These data are reinterpreted in conjunction with lattice parameter data obtained on an alloy containing 12.2 pet Al, whose isothermal transformations have been reported elsewhere.5 The a Lattice Parameters of a 12.2 Pet A1-Cu Alloy—~iffraction patterns of completely transformed specimens were obtained in a back reflection camera using copper Ka radiation. Lattice parameters of

Jan 1, 1959

By M. G. Corson

The iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well-known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 1.5 per cent. silicon (Fig. I). Starting at the ultimate strength of 35,000 lb. and at a yield point of 16,000 lb. for pure electrolytic iron, one reaches a maximurn strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb, per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2..5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated. Yensen observed an enormous drop in elongation and area reduction at about 2.65 per cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to 1.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction. Yensen's graphs, as shown in Fig. 1, indicate also a considerable drop in strength and yield point at the same point of 2.65 per cent. Si,

By Wheeler P. Davey

In an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. l.) Fig. 2 is a photograph of the end of the punching, showing the hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of radiographing metals. In order to gain some preliminary data, several pieces of 1/2-in. (12.5-mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter I.........................................1/4 in. =6.3 mm 2........................................1/8 in. =3.l mm. 3................................... 1/16 in. = 1.6mm. 4....................................... 1/32 in. = 0.8 mm. 5........................................1/64 in. = 0.4 mm. Exposures were made on Seed X-ray plates at 20 in. (50 cm.) distance with Coolidge tube X-117, operated on Scheidel-Western induction coil with mercury turbine break. The X-ray plate was placed on a sheet of 1/8in. (3.1-mm.) lead. The steel was placed above this and a Iead

Jan 1, 1916

By J. S. Hromatko, L. J. Gurevich

In the course of the examination, at the BureLu of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undcrtaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are, satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed." Table 1.—Thirty-"five-mdh Testing Record of Fusible Plugs Causes of Rejection Inspection Period June-November, 1916.................. 311 32.8 47.2 3.8 11.5 15. 1 10.9 1 1.9 4.5 December, 1916-May, 1917............. 318 71.4 28.6 2.2 4.4 12.8 5.9 i ... 2.8 June-November, 1917.................. 228 73.0 27.01 ... 9.6, 5.2 9.6' ... 0.8 December, 1917-May. 1918............. 214 72.028.0 0.9 0.4 11.6 7.0 ... 7.9 June-November, 1918...............250 70.7 29.3 ... 2.0 20.0 5.2 ....2.8 December, 1918-April. 1919............ 23378.121.9 7.2 1.2 1 4.7 3.0 ... 6.0 Total 35 months....................1544.69.7 30.3 2.3 4.8 11 0 6.9 0.3 4.1

Jan 1, 1921

By C. Laird, C. E. Feltner

An investigation into the effect of a material's slip character on its high strain fatigue properties has been carried out using copper and Cu-7.5 wt pct A1 as representative wavy and planar slip mode materials, respectively. In copper, the constant term and exponent in the Coffin-Manson equation, ?EpNf1/2 = const, are unaffected by the temperature of testing or the history of the metal. On the other hand, in Cu-7.5 wl pcl Al, while the exponent is invariant, the constant is increased with respect to copper and increased further with decrease in temperature. The life in Cu-7.5 wt pct A1 is double that of copper at room temperature and about four times at 78°K. Fractoflaphic studies indicate that these diffevences in life are associated with the early stages of cracking. In copper, severe surface rumpling provides crack nuclei at pain boundaries independent of' testing temperature or the history of the metal. In Cu-7.5 wt pct Al, the planar slip mode of deformation prevents grain boundary folding; crack nucleation is therefore mainly transgranular and the increase in life with respect to copper is associated with a prolonged linking-up stage of such transgranulay cracks. At the lower temperature the increased difficulty of cross slip inhibits multiplication of trans-granular cracks and retards the linking-up process, giving a further enhaancement in life. It is expected that such behavior will be found general in materials of wavy and planar slip mode, respectively. STAGE II crack propagation in high strain fatigue takes place by a repetitive process of crack tip blunting in the tension part of a fatigue cycle followed by resharpening of the crack in the compression part.1-3 This mechanism has come to be called the "plastic relaxation process".3 At very high strains (lives to failure less than 103 cycles), most of the life of a specimen is spent in crack propagation by the plastic relaxation process.4,5 Since the differences in the cyclic strain hardening behavior of metals and alloys are comparatively small in this strain range,6,7 the amount of blunting at a crack tip depends primarily on the applied strain amplitude. The rate of crack propagation in this life range is therefore nearly constant with respect to material and temperature of testing. In the longer life portion of the high strain fatigue range (l03 to 103 cycles to failure), a considerable fraction of the lives is spent in crack initiation and Stage I growth. Grain boundaries have frequently4,5,8 been found to be the sites for this growth which is also associated with a surface folding process.4'5 Such folding behavior may also be general in any material having a grain structure and capable of plastic deformation. It has therefore been suggested475 that the universality of the Coff in-Manson law,9'10 constant,* where ?Ep is the plastic strain range and Nf the number of cycles to failure, is reflected in the approximate invariance of both the crack initiation and propagation behavior. It happens that, in most investigations of the phenomena associated with failure,4,5,8 materials with a wavy slip mode have been used as vehicles for the studies, or else "normally" planar slip mode materials have been tested under conditions giving rise to wavy glide deformation, e.g., stainless steels cycled at high temperature.'' The purpose of the present investigation was to determine whether or not different cracking phenomena would occur when the slip mode of a material is planar and if the associated life to failure would be different than that of a wavy slip

Jan 1, 1968

By W. F. Rogers, J. A. Stewart, P. J. Kalish, E. O. Bennett

Detailed descriptions are given of materials, apparatus and the experimental procedure used to study the effect of bacteria on sandstone permeability. The factors affecting permeability during injection of bacterial suspensions which have been investigated are: (I) concentration of bacteria; (2) core permeability and median pore size; (3) species of bacteria, mode of aggregation and relative size; (4) injection rate or pressure differential; (5) mean pressure; and (6) depth of penetration of bacteria. The investigation demonstrated that bacteria cannot reduce core pertneability to zero and that their effect on permeability is subject to definite limitations. Remedial or permeability restoration studies also were made. Acidization in combination with reverse flow war found to be an effective method for restoring permeability In cores partially plugged with bacteria. The relationship between the bacterial quantities in the laboratory tests and those found in field operations is discussed. The linear laboratory flow data have been translated into terms of field radial systems; these data indicate the most practical methods of maintaining injection rates in the presence of bacteria are to increase injection pressures or hydraulically fracture the formation. INTRODUCTION It has long been known that various bacteria flourish in the above-ground components of oil field water-injection systems. The presence of these bacteria has led to the suspicion that they might enter into the causes for reduction of injection well permeability, but only recently has an attempt been made to describe the effects quantitatively.1 Biocides are used in many cases without a firm knowledge as to whether the bacteria are killed, or if they are, whether the dead cells affect formation permeability. This project was undertaken as part of a study to determine the effect of bacteria, residual oil and precipitated solids such as iron sulfide or calcium carbonate on the permeability of sandstones and to learn whether any of these materials adversely affect brine injectivity in secondary recovery or disposal operations. This report deals with that portion relating to the effect of bacteria. MATERIALS CORES Three different permeability ranges of Berea sandstone cores were used in the study. The range of initial, absolute brine permeabilities kj were: high — 278 to 400 md: medium—130 to 162 md; and low—17.7 to 48.3 md. The permeability data for the cores used in the tests are included in Table 1. All cores were cut to a nominal 1 in. diameter. Following air permeability determinations, they were molded with an epoxy resin in 1.5 in. ID aluminum sleeves. The sleeves had drilled and tapped holes for intermediate pressure connections along the length of the cores. After molding, the high- and medium-permeability cores were trimmed to 4 in. in length and the low-permeability cores to 2 in. These lengths resulted in pore volumes of approximately 10.9, 10.4 and 4.4 ml, respectively, for the high-, medium- and low-permeability cores. Pressure-transmitting channels were drilled through the plastic into the core proper, using the sleeve holes as drill guides. Width and depth of channel penetration into the core proper were approximately 0.03 in. and 0.05 in., respectively. Three pressure taps were used with all cores; for the high- and medium-permeability cores the taps were spaced 1 in. apart; for the low-permeability cores the taps were spaced 0.4, 0.8 and 1.2 in. from the inlet end. Pore size distributions were calculated from restored-state capillary pressure curves for representative cores in each of the three permeability ranges. In each case the pore size range with the greatest percentage of the pore space included the very small pores up to 0.5 micron in radius. The median pore radii were in the 5.5 to 6 micron range for the high-permeability cores; in the 4.5 to 5 micron range for the medium-permeability cores; and in the 3.5 to 4 micron range for the low-permeability cores.

Jan 1, 1965

By T. J. Koppenaal

The surface slip line structure has been investigated by optical microscopy during the easy glide deformation of Cu-A1 single crystals as a function of composition, testing temperature and prior thermal treatment. The slip line structure in alloys of 2.5 or less at. pct Al is similar to pure copper, while alloys of 5 or more at. pct Al show slip tracings typical of a brass. Cross slip is observed in the "a-brass type" crystals and the amount of this type of slip increases rapidly with aluminum content. The cross slip tendency in 14 at. pct Al crystals is signicantly higher when tested at 150°C as compared to 4.2" and 77°K. In addition, cross slip is more pronounced in this alloy in the furnace cooled condition than when quenched from 450°C. The cross slip behavior is analyzed in terms of existing models for this type of deformation. In two previous investigations, reports of yield points1 and solid solution strengthening2 in Cu-A1 single crystals have been given. This paper enlarges upon the brief description of the slip line structure discussed in these reports. Since the easy glide slip line pattern of copper changes markedly with the addition of -30 pct Zn (-brass),3 a study of slip lines as a function of solute additions in Cu solid solutions should help to explain some of these differences. In addition to composition variables, slip lines have also been studied as a function of testing temperature and prior thermal treatment. PROCEDURE The slip line observations were made on single crystals of 0.5 to 14 at. pct Al using a light microscope. Details concerning the preparation and basic testing procedure are given elsewhere.' Prior to testing, each crystal was homogenized at 900°C for 24 hrs, furnace cooled, and electrolytically polished in a 60 pct phosphoric acid solution. The strain rate was-5 X 10 sec-I in each case. Unless otherwise stated, all observations reported upon here were made during the early stages of easy glide. RESULTS AND DISCUSSION The maximum magnification generally used was 1000X, and slip lines could be resolved down to about 105 cm (1000A). This resolution is appreciably less than obtainable with electron microscopy replica techniques where the replication can resolve slip lines down to about 40 A. Thus, while many qualitative features could be studied, the type of quantitative data obtainable with an electron microscopy replica study could not be made. Crystals containing 0.5 and 2.5 at. pct Al deform much like pure copper exhibiting a high density of fine slip lines that cover the entire gage length of the specimens. Fig. 1 shows the surface slip line pattern in a 2.5 at. pct A1 extended 0.01 shear strain at room temperature. Crystals having 5 to 14 at. pct A1 showed appreciably coarser slip lines that were generally concentrated at one end of the gage length. During easy glide these coarse slip lines propagate along the gage length in a manner similar to that observed in a-brass single crystals by Piercy, Cahn, and cottrel14 and refered to by them as a Lüders band propagation. Fig. 2 shows a typical area of these coarse slips in a 14 at. pct A1 crystal after a room temperature shear strain of 0.01. Two slip systems were apparently active. Using a method described by Cullity, the angles, between the specimen axis and the normals of the primary and secondary slip planes were determined to be 50 and 84 deg, respectively. 'From the Laue photograph, was 52, 81, 66, and 30 deg for the primary, cross, conjugate, and fourth slip planes, respectively. The secondary active plane in Fig. 2 is thus established as the cross slip plane, and the operative slip system is evidently the cross slip system, e.g., slip

Jan 1, 1963

By Steven Mitchell

BACKGROUND Homestake Mining Company began milling operations at the Bulldog Mountain Mine near Creede, Colorado in 1969. The Bulldog Mill, rated at 350 tpd, produces a bulk flotation condentrate assaying about 180 oz/T Ag and 20% Pb, from heads of about 16 oz/T Ag and 2% Pb. The circuit is straightforward with two-stage grinding to 1-5% plus 65 mesh, followed by rougher and cleaner flotation. Reagents used are Z-6, Z-11, Aerofloat 242 and Aero Promoter 404, with an Aerofroth 65-MIBC mixture for a frother. Additional information on the geology, mine and mill are available in references (1) and (2). A flow sheet for the mill and CIP plant together is attached as Figure 1. Final flotation tailings normally vary from 1.5 - 2.0 oz/T Ag. These tailings are cycloned to produce sand for underground backfill. After cycloning, the sands are repulped and given a final scavenger float. This sand scavenger recovers a small additional amount of silver which recycles back to the main flotation circuit. The tailings are recycloned and pumped to the mine or, if the mine cannot accept sand, to tailings. The majority of the silver in the flotation tailings exists in the fine fractions; cycloning upgrades the slimes and lowers the assay of the sand. The sand, after scavenging, typically assays 0.5 oz/T Ag, and the slimes assay about 3.0-3.5 oz/T Ag. From 1969 to 1976 all of the slime tailings and the sand tailings not used underground were impounded in a tailings pond located about

Jan 1, 1983

By E. C. IBBOTSON

THIS process was reported upon by the Canadian Commission in 1904, and much detailed information was also given in a paper by Chief Engineer V. Engelhardt.1 Believing that some of the latest particulars of the process will be of interest, I submit the following data. At Gysinge in Sweden during the year ending May 31, 1906, from a fixed furnace giving 1 ton (2,240 lb.) of steel per tap, there were produced 950 tons of tool-steel and special steel ingots. . In carbon and iron tool-steels all the usual tempers were made. The bulk of this steel was made from charges composed of about 80 per cent of Swedish white pig-iron and 20 per cent. of steel-scrap. The percentage of carbon was regulated by the addition of briquettes. Other charges were made from Swedish white iron and steel-scrap. The average time taken per charge, for the year, when adding briquettes, was 7* hr., and the electric energy consumed was 1,128 units (kilowatt-hours) per ton. The average time per charge for white-iron and scrap charges was 5.5 hr., and the electric energy consumed was 886 units per ton. These consumptions include all time and energy lost from various causes, such as bad water-supply, ice, etc. It is quite ordinary practice to complete the charges with briquettes in 6.5 hr., and without briquettes in 5 hr., as shown by the following typical charges White pig-iron, 1,457; steel-scrap, 439; briquettes, 220; ferrosilicon (50 per cent. of silicon), 17 ; ferromanganese (80 per cent. of manganese), 15 lb. ; and aluminum, 1 oz.=

Nov 1, 1906

By H. O. Hofman, H. L. Norton

Zinc smelters in the central western States have established a very high standard of purity for blende-concentrates, viz., zinc 60, iron less than 3, and lead less than 1 per cent. The very low percentage of iron is made possible by the blende containing less than 0.5 per cent. of isomorphous iron sulphide and by the sparing occurrence of pyritic material in the large blende-deposits of southwestern Missouri and southeastern Kansas. The blende in these districts occurs in sub-carboniferous limestone, and is associated with chert, residual clay, cal-cite, pyrite or marcasite and bitumen. The different minerals are coarse and therefore readily separated by mechanical washing from the blende, with the exception of pyrite and marcasite, as blende has a specific gravity of from 3.9 to 4.1; marcasite, from 4.85 to 4.90; and pyrite, from 4.95 to 5.10. The common procedure of dressing the ores' is to crush in a breaker, size in a trommel with 0.5-in. holes, pass the over-size through roughing-rolls and then jig the ore, now reduced to 0.5 in. maximum size, in roughing multiple-sieve jigs. The products of these are waste-tailings, side-discharge coarse concentrates, side-discharge coarse middlings and bottom-discharge fine middlings. The coarse concentrates are sent to the market. The coarse middlings are crushed in middlings-rolls and brought back into the system by feeding into the main trommel. The fine middlings are cleaned upon finishing-jigs. Any pyrite or marcasite present follows the blende and increases the percent- +1MASSACHUSETTS INSTITUTE OF TECHNOLOGY, BOSTON, MASS.

Jan 1, 1905

By R. B. Russell

SINCE Cahn's¹ paper on plastic deformation in orthorhombic (a) uranium an increasing amount of work is to be expected on orientation of single crystals and preferred orientation in this metal. It would seem desirable to have a table of angles between crystallographic planes (hkl) and (HKL). Table I shows these angles as distances from (loo), (0l0), and (00l), and in Fig. 1 as a standard (001) stereographic projection. Only the locations of poles whose diffracting planes produce Cu Ka reflections up to 0 = 70.5" (i.e. (154) ) are given." The relative reflection of these planes are represented by circle diameters. It is hoped that the projection may also be used in making inverse pole figures, originally suggested by Harris.' Values of 4 were calculated from the expression hH kK 1L cos = hH/a²+kK/b²-lL/c² where the lattice parameters a, b, c, and the spac-ings d were taken from the work of Jacob and Warren." (They report a = 2.852 kX (2.8578 A), b = 5.865 kX (5.8768 A), c = 4.945 kX (4.9550 A).) The parameters reported by them may be subject to revision,4,5 accordingly the interplanar angles are listed to only the nearest tenth of a degree. References ¹R. W. Cahn: Acta Metallurgica (1953) 1, p. 49. ¹G. B. Harris: Philosophical Magazine (1952) 43, p. 113. 3C. W. Jacob and B. E. Warren: Journal ACS (1937) 59, p. 2588. 4J. S. Lukesh: Acta Crystallographica (1949) 2, p. 420. ³ J. Thewlis: Nature (1951) 168, p. 198.

Jan 1, 1954

By R. Gilman Brown

INTRODUCTION. MINES are interesting by reason of what they have done for man, or of what has been done for them by nature. Not all are interesting on both scores. Many profitable mines are commonplace to the geologist; and many presenting unique geological conditions have been sad failures commercially. The Standard group at Bodie has produced in 25 years, $14,500,000, paying $5,000,000 in dividends.' On the other hand, this output has been mined (almost wholly above the 1,000-ft. level) from a system of more than 100 veins, ranging in thickness-from 0.5 in. of "specimen rock" to 30 ft. of clay and quartz; distributed through a zone about 2,000" ft. in width, and representing from three to five distinct periods of formation. This group, therefore, by reason of its industrial record as well as its geological features, may fairly be regarded as doubly interesting. The Bodie district occupies an island of recent (Tertiary) hornblende-andesite, surrounded by a complex of igneous rocks and breccias. It lies at the summit of the eastern foot-hills of the Sierra Nevada mountains, and within the Great Basin, a few miles from its western edge, marked here by Mono lake on the line of the Great Fault. The average elevation of the outcroppings of the veins may be taken at about 5,700 ft. The andesite projects from south to north in a great tongue, 12,000 ft. long and 5,000 ft. wide, reaching an extreme height at the northern end of perhaps 1,000 ft. above the adjoining small canyons. These separate it from the main mass of the foot-hill

Jul 1, 1907

By W. S. Ayres

I. Introduction. This cavern was discovered Oct. 32,1904, by Mr. Charles 8. Deutschman, in company with whom I made, May 29 to June 3,1905, at the request of Mr. Howard Douglas, Superintendent of the Canadian National Parks, the first exploration of it for the Canadian government. The results were stated in a paper, orally presented, with lantern-views from my photographs, at the British Columbia Meeting of the Institute, Victoria, B. C., July 5, 1905.* The present paper embodies also the results of a second examination, made Oct. 25 to 29, 1905. The accompanging map, Fig. 1, will serve as a guide to the following description. 11. Location. The cavern is situated at snow-line, at the head-waters of Cougar creek, on the west slopes of the Selkirks, about 2 miles north from Ross Peak water-tank, and 5.5 miles west from Glacier station, on the main line of the Canadian Pacific Railway. It was then reached by an arduous climb from the water-tank, up the ravine of Cougar creek, for 8,000 ft. (2,000 ft. of altitude) over rock- and snow-slides, and through a thick tangle of alders. But an easy and very picturesque trail has, during the past summer, been opened by the government from Glacier station, which is also a hotel of the railway company. Figs. 3, 3 and 4 represent views, not heretofore published, of the grand scenery of this region, so rapidly becoming the object of attraction to thousands of tourists from all parts of the world. These views, as well as those shown in Figs. 5, 6, 7, 8

Jan 1, 1908

By Edward Keller

In a paper, " A Study of the Elimination of Impurities from Copper-Mattes, etc.," presented to the Institute at the Atlantic City meeting, February, 1898, I gave certain figures which I called the relative slaggability in refining copper. In that paper* will be found the following pertaining to this subject: Relative Slaggability in Refining Converter-Copper. Cu. Pb. Bi. Sb. As. Se, Te. 1 129.5 1.13 7.30 5.22 0.81 and Relative Slaggability in Refining Electrolytic Copper. Cu. Pb. Sb. As. 1 41 9.97 7.13 Since there is a, possibility of misinterpretation of the above values, the following supplementary information may seem justified in explanation. As the contents of impurities in the unrefined or crude copper were unknown, the contents of the refined copper were substituted therefor, merely in order to obtain the two series of figures for comparison. These figures are higher than they would be had I been able to take the correct ones for the unrefined copper. The high figure, 129.5, for lead, in the case of converter-copper, means simply that more lead was slagged from the crude copper than remained in the refined copper; or, in definite values, that to 1 per cent. of copper slagged, the ratio of the lead gone into the slag and the lead remaining in the refined copper is 129.5 : 100. It is possible to approximate the true slaggability much more closely by adding the quantities of impurities in the refined copper to those in the slag, thus obtaining values for the crude copper in which the amounts volatilized are ignored (the latter

Jan 1, 1901

By M. G. F. Sohnlein

IN a Bolivian tin concentrator an appliance was needed to furnish a suitable product for fine jigging from a pulp of the following composition: Mesh Per Cent. +20 8.0 +40 36.5 +60 9.0 +80 10.5 +100 5.5 +150 4.51 -150 25.0 99.0 Loss 1.0 IN the jigging process, particles of cassiterite as small as 0.1 mm. can be recovered, provided they are not present in excess, that is if the material treated on the jigs contains sufficient coarser sands to keep the interstices between the grains open. Removing the fine material from the pulp by screening, to prepare the jig feed, is impractical, because that means the use of an 80-mesh screen or finer, and is not as effective as hydraulic classification. A screen would eliminate mineral grains from the feed which can be recovered by jigging, and in addition would throw more gangue and low-grade middling on to the jig. Formerly a one-spigot Richards vortex classifier had been used to accomplish this separation, but the tangential openings through which the hydraulic water enters became clogged by fine vegetal matter with which the water was contaminated, and which it was impossible to remove from the water. Consequently the work of the classifier was imperfect and a good deal of slime was sent to the jig. When designing the plant referred to in this paper it was decided to use a hydraulic classifier as shown in Fig. 1. The essential features had been copied from the Anaconda classifier.1 This remodeled classifier consists of a truncated pyramidal wooden hooper A with an attachment of cast iron

Jan 4, 1916

1. List of Manuscripts Seen in America 2. List of Manuscripts Seen in England 3. List of Maps Examined 4. List of Newspapers Examined 5. General Bibliography - Numbered Reference List

Jan 1, 1942

By Charles W. Sweetwood

THE Western phosphate field, virtually ignored for 40 years, has been undergoing a rapid climb to economic importance. Until World War II there seemed to be no reason for developing the phosphate rock region of the Intermountain Empire. But the tremendously increased demand for food production and the needs of many branches of the chemical industry changed all that. Quite suddenly a report made by the U. S. Geological Survey at the turn of the century became important. The survey showed that 60 pet of the nation's phosphate reserves were in the western phosphate field. Simplot Fertilizer Co. was one of the first to become actively interested in the development of the area. In August, 1945 the company began exploration of the Phosphoria Formation on the Fort Hall Indian Reservation. The result was the Gay Mine, about 18 miles east of Indian Agency Headquarters at Fort Hall, Idaho, developed to supply high grade phosphate rock for processing into superphosphate fertilizer at the company's Pocatello plant. Six ft of high grade oolitic phosphate rock (ranging from 32.5 to 34.5 pet P2O5) were discovered at the base of the Phosphoria Formation by diamond drilling and dozer trenching. High quality and thickness, plus the fact that the formation lay flat and near the surface made strip and open pit mining possible. In one year of mining, starting June 1946, a total of 53,000 tons of main bed oolitic phosphate rock was hauled to Pocatello for processing into supersulphate. The first year's operation was in

Jan 1, 1952

By P. Chiotti, J. T. Mason

Metallographic, thermal, X-ray, and vapor-pressure data were employed in establishing the Ce-Zn phase diagram. Nine compounds and three eutectics were observed. The eutectic compositions in weight percent zinc and temperatures are 10 pct and 495"C, 37 pct and 795°C, and 56 pct and 810°C. Three of the compounds, CeZn, CeZnn, and CeZne.5, melt congru-ently at 825°, 87.505°, and 980°C, respectively; the other six compounds, CeZns, CeZns.67, CeZn4.5, CeZn5.25, CeZn,, and CeZnll, decompose peritectically at 820°, 840°, 870°, 885", 960°, and 795"C, respectively. The compound CeZn5.25 is an AB5 type with a small range of composition which lies on the zinc-rich side of the 1 to 5 stoichiometry. Zinc vapor-pressure data obtained by the dewpoint method were employed in calczilating the thermodynamic properties of both the liquid alloys and solid compounds. The data for the A critical review of the information available on the Ce-Zn system up to 1960 has been given by K. Gschneidner, Jr.' Of particular interest is the work by J. schramm2 who investigated the region between 55 and 100 wt pct Zn and reported a CeZn,, compound which decomposes peritectically at 785"C, a CeZn, compound which melts congruently at 972"C, and five temperature horizontals at 79@, 817", 840", liquid alloys were fitted to the relation from which the relation was obtained by integration. In these relations F XS is the excess partial molal free energy, N is atom fraction, and the constants c and d have the values c = (-22,000 + 7.0T) and d = 6171,000 + 74.0T). Relations for the standard free energy of formation for the solid compounds were derived from the data. At 973°K the enthalpy in kilocalories per gram-atom z)aries from —11.3 for CeZnz to —8.21 for CeZn~l and the free energy in the same units varies from —7.1 joy CeZn, to -3.82 for CeZn11. and 942°C in the region between 55 and 75 wt pct Zn. No attempt was made to identify other features of the system. I. Johnson and R. yonko3 used a fused-salt cell to measure the electromotive force between pure cerium and an alloy consisting of zinc-rich liquid in equilibrium with CeZnll. Solubility data for cerium in zinc has been reported by J. Knighton et u1 .4 Johnson and Yonko give the following equa-. tions for the mole fraction of cerium in zinc and the standard free energy of formation of CeZnll:

Jan 1, 1965

US 4,181,703-Removal of magnesium impurity from phosphate rock. Crushed screened ore containing more than 0.3% by weight of magnesium is slurried with sea water, acidified with sulfuric acid to a pH value not lower than 2 5, and filtered and washed before the neutralization point is reached. W. Wengeler, F. Wolstein, and E. Hoffman, assigned to Uhde G.m.b.H. Jan. 1, 1980 4 pp (423-167) Filed: 11-18-77 (852,918)

Jan 1, 1982

By George Kunz

(Butte Meeting, August, 1913.) THE manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg. ; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a kilogram. He also called attention to the fact that while this would depreciate the present diamond carat or pearl grain only about 2.5 per cent., it would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.1 The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl.2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sèvres, is largely clue the eventual success of this eminently desirable reform, which lie has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.3

Jan 7, 1913