Search Documents

By N. J. Grant, B. C. Giessen, M. Morris

The slvuclures of alloys in the system In-Bi have been investigated after (levy vapid queuching from the mell (splat cooling) to -190°C. Tuo-phase fields could be suppressed over most of the tota1 concentvalion range; five melastable phases a1, a2, ?, ?1. and ß exisl, of which four have simple elementtike structures. For example, ß has the A5 struclure of white till. Crystal-tographic data and coordination numbers for these phases aye given, as well as addilional information on the equilibrium diagram, where a new phase In5Bi3 teas found. THE phase diagrams of binary combinations of B elements from the groups B2, B3, B4, and B5 are usually of a simple type and show considerably fewer intermediate phases than combinations of these elements with A metals, transition metals, or the B1 noble metals. Aside from phases such as the typical B3-B5 compounds with the ZnS-B3 structure type, few stoichiometric phases are known; among them are In2Bi and 1nBi.l Nonstoichiometric phases include ß (In-Sn), a1, (In-Pb), and the tin-rich ? phases in the In-Sn, Cd-Sn, and Hg-Sn systems.' The first two phases have a close relationship to indium, while the latter group are known to be structurally related to a Sn. Thus, there are generally no immediate experimental data for the correlation of the crystal structures of B metals and B metal combinations with certain monotonously varying parameters, such as the valence electron concentration (VEC), or the average atomic size. Such parameters have been recognized as structure determining, e.g., for the transition 4 Sn — y phase,2,3 where nonintegral valence electron concentrations are encountered. It should be possible to extend such correlations to other binary systems, if nonequilibrium single-phase alloys could be produced over broad valence electron concentration ranges, and if their crystal structures could be regarded as being imposed by their electronic states. It has been shown in the case of the tin-rich 7 phases3 that alloy phases with typical crystal structures can be produced in B metal alloys rapidly quenched from the liquid to -190°C by the splat cooling technique due to Duwez,3-8 and reviewed in Refs. 5 and 6. The In-Bi system was selected because it extends over a valence electron concentration range in which several metastable, nonstoichiometrir phases could be expected to occur. Further, the low melting points of the known intermediate phases, In2Bi and InBi, Fig. 1(a), indicated low binding energies and thus possibly low driving forces for the formation Of the equilibrium structures. EXPERIMENTAL TECHNIQUES AND RESULTS The preparation of the quenched foils followed the practice described in Ref. 3. Master alloys were produced by melting of indium (99.97+) and bismuth (99.99+) in evacuated Vycor capsules or in an inert gas arc furnace; quantities of 20 mg were splat-cooled onto copper and silver substrates held at - 190°C; and crystal structures and lattice parameters were determined on a GE XRD-5 diffractometer using Cu Ka, radiation at -190°C and at room temperature. The duplication of each run with both substrates permitted the elimination of overlap of the substrate diffraction pattern and that of the investigated substance. The XRD patterns were usually taken from sin2 " = 0.03 to 0.35; the substrate was used as a means of internal calibration. The fractional accuracy of the lattice parameters of metastable phases is approximately 10-3 In the following, all percentages are in atomic percent. The stable and metastable phases found after rapid quenching to -190°C are listed in Table I, together with estimated concentration ranges and crystallographic data. The investigated alloys and phases present in them are given in Table 11. Except for the region between indium with 33 and 50 pct Bi, where a revision of the equilibrium phase diagram became necessary to include a new stoichiometric phase In5Bi3, the diffraction patterns taken after heating to room temperature agreed with those expected from the phase diagram, Fig. l(a). This suggests that the new nonstoichiometric phases are not stable at room temperature, thus following the observations made for the y phases based on tin.3 Results concerning the equilibrium phases In2Bi and In5Bi3 and the revision of the equilibrium phase diagram which is made necessary by the inclusion of In5Bi3 will be treated first. The Crystal Structure of In2Bi. Makarov7 had identified In2Bi as belonging to the AlB2-C32 type ; however, in a later paper the structure was revised.8 In2Bio was found to be of the Ni21n-B8ß type,21 with a = 5.496A, c = 6.57.9A, and N = 6 atoms per unit cell.9 This crystal structure was confirmed in the present work; definite evidence for the doubling of the c axis, as compared to the A1B2-C32 type, and for the proposed order structure, was found in the powder pattern. The observed lattice parameters agree well with those of Ref. 8; those measured at -190°C are given- in Table I. The Crystal Structure of In5Bi3. A new, equilibrium, intermediate phase was identified in slow-cooled, as-cast alloys; it was identified as In5Bi3. The structure has been worked out by Giessen and Grant;" lattice parameters at -190°C are given in Table I. This phase is probably identical with "In3Bi2", produced by vapor deposition techniques, but not recognized as an equilibrium phase by Palatnik et a1.11 After completion of the present work, the existence of In5Bi3 has also been demonstrated by superconductivity measurements on In-Bi alloys.20

Jan 1, 1968

By R. P. Rothwell

A Reference to the geological map of Alabama shows the Goalmeasures of that State to form three distinct fields. The Coosu, or most easterly, contains about one hundred square miles ; the Cahaba, or middle field, which is also the most southern true coal in the United States, contains about 230 square miles ; and the Warrior field, which contains in the State of Alabama some 5000 square miles, is the southern extremity of the great carboniferous deposit, which extends through Pennsylvania, West Virginia, Kentucky, Tennessee, and Georgia. But very little has yet been done towards developing those coalfields, partly owing to the absence of all commercial manufacturing enterprise in the South under slavery, and partly owing to the want of capital and the disturbed condition of the South since the war. During the past three or four years I have devoted a large part of my time to the examination of the coal and iron ores of this range,

[Abrahamson, Guy C., (5'43) Lt., 0-880861, Hammer Field Fresno Calif. Adamec, LAW, (8'42) c/o Braden Copper Co., Rancagua, Chile. Adams, Karl S., (9'43) Univ. of New Hampshire, Durham, N. H. Agnilar, Roperto Q., (9'43) Texas College of Mines, El Paso Texas. Ainge, B'onald Farra, (943) Otago University, Dunedin, New Zealand. Akaran, Cevdet A,, (9'44) Pennsylvania State College, State College, Pa. Albala, Americo, (5'44) School of Mineral Industries, The Pennsylvania State College, State College, PA.]

Jan 1, 1946

By B. R. Hollebone

The chemical action of molten anhydrous pyridinium chloride (pyridine hydrochloride) on oxy salts and ores of some Group IV and V metals are discussed-in particular zirconium, hafnium, niobium (columbium) , and tantalum. Laboratory-scale experiments are described whose results suggest that this reaction might provide a practicable means of converting ores of these metals to the anhydrous metal chlorides. Experimental results are given which provide some insight into the nature of the reactions and some of the compounds which could be present at intermediate stages. The treatment of ores of the more refractory metals is difficult and expensive and often demands the use of gaseous chlorine, hydrogen fluoride, or other reagents which are, if nothing else, expensive and dangerous to use. This situation is, of course, due to the strong metal-oxygen affinity resulting from the high charge and the small size of the metal ion which combine to produce such high lattice energy in the metal oxide as to defeat standard reduction methods. Thus, the characteristic of these metals which leads to one of their most important properties—corrosion resistance—is the main hurdle in obtaining the metal. Many common methods' for treating ores of zirconium and niobium (columbium), for example, proceed as directly as possible to the preparation of anhydrous halides. These halides are purified by now standard processes of solvent extraction, fractional distillation, and so on. This paper reports on preliminary stages in the development of a method of treating these ores—particularly of niobium—so as to prepare the anhydrous, volatile halides by the use of chemical reagents which are much more easily handled than those used at present. CHEMICAL PRINCIPLES The solvent action of aminium halides has been referred to periodically in the literature over several decades. The chemistry of pyridinium chloride has been discussed particularly by Audreith2 and Starke.3 However, since this is not familiar chemistry in its nonaqueous setting, it is perhaps well to point out some general metallurgical principles and applications. One can use, as point of departure, the fact that HC1 dissolved in pyridine is an acid very much the same as aqueous HC1. It thus gives essentially all the reactions of the HC1 with which we are familiar. However, when the ratio of HC1:pyridine reaches 1:l (a ratio far higher than is possible with H2O) the solution becomes solid C5F5NHC1, pyridinium chloride.* Inter- estingly, the acidic properties of HC1 persist in this medium, although they are manifest only in the molten state of the compound. Some typical reactions of divalent metal compounds which we have carried out in our laboratories are the following: 2PyHCl + Zn — (ZnCl2) + H2 + 2Py 2PyHCl + MnO — (MnCl2) + H2O + 2Py 2PyHCl + CuS — (CuCl2) + H2S + 2Py 2PyHCl + CaCO3 — (CaCl2) + H2O + CO2 + 2Py In these equations, the parentheses indicate a solvated compound which in water would be predominantly a hydra ted cation but which in molten PyHCl will more likely be a complex chloro-anion of the type MC14-. Some important physical properties of pyridinium chloride (PyHCl) are given in Table I. One sees from the data in Table I that at the temperature of molten pyridinium chloride both water and pyridine will boil away. Thus the system will be kept anhydrous. For this reason the reaction 2NbCl5 + 5H2O— Nb2O5 + 10HC1 has no counterpart in molten PyHCl. Instead, the chloride is made even more stable by the formation of a hexachloro complex: Nb2O5 + 12PyHC1 — 2PyHNbC16 + 5H2O + 10Py One interesting property of these complexes is their thermal instability which for the case of niobium can be illustrated as PyHNbCl6 — PyHCl + NbCl5 With a view to possible use of this chemistry in ore treatment, we have attempted to dissolve Pyrochlore (essentially FeO - Nb2O5) and recover the NbC15 from it.

Jan 1, 1968

By Orvar Nyquist, Klaus W. K. Lange, John Chipman

Liquid Fe-C-Si alloys containing 0 to 12 pet Si and up to 4 pet C were equilibrated with carburizing gases at 1550°C. Two to 5 alloys simultaneously were held in close proximity for 5 to 7 hr to establish uniform carbon activity in the group. Analysis of the data gives the activity coefficient of carbon as a function of the mole fractions of carbon and silicon, Fig. 7. Values of the interaction coefficients at infinite dilution are

Jan 1, 1962

By W. F. Mullen, C. W. Stickler

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behrel and Bowles2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate. A study of the basic elements in the production of roofing slate, structural slate, and slate blackboards among selected slate producers revealed comparatively few refinements. Any marked difference in operating method was characterized largely by the available equipment, a noticeable difference in the working properties of the rock quarried by a particular company, and by either the habit thinking or ingenuity of the individual operators. With the hope that significant economies in manufacture might result, all the unit operations were broken down into elements for study and analysis. The greater part of the study encompassed those operations from the quarry rim to the finished product; however, to obtain a reasonable synthesis of time allotments per operation, several analyses of quarrying from the finish of the wire saw cut are included for reference. The complete study of quarrying made by Bowles several years ago resulted in the introduction of the wire saw into the operation; there appears to be a need for as fundamental a change in the processing of finished slate as the wire saw was in the quarrying process. Fig. 1 illustrates the flowsheet of quarried rock from the parent bed to the quarry rim with the basic elements which contribute to the difficulty of removing slate from the ground. In Pennsylvania roofing slate is produced by one of three procedures, many operations of which are quite similar. In the traditional or classical method the quarried rock is reduced by sculping and auxiliary manual treatment to workable size and then is split and dressed (trimmed to size) in the conventional shanty. Archaic as this method might appear, there are several elements that result in substantial savings over more mechanized operations. In a modified version of this method, the block is reduced by sawing and gouging preparatory to splitting and dressing in indoor stations. This method is particularly adaptable to rock which fractures unevenly by conventional sculping methods. In the third and more modern method, reduced block received from the block maker is diamond-sawed to length and finished on a production line. Fig. 2 illustrates the flow pattern in each case. In the modified and more modern plans, dressing is done on mechanically-operated trimming machines, which appreciably reduce the fatigue factor of the operator. However, it should be noted that it is advantageous for the operator to be able to control the speed of the knife to prevent breakage of certain classes of stock. In the classical plan the splitter and dresser normally act as blockmakers also and carry their eighter slabs (equivalent in thickness to eight shingles) into the shanties themselves, all of which adds to fatigue and reduced efficiency. The extremely low investment and operating expense of the classical method has undoubtedly been of paramount importance in its continuation. Production of Mill Stock The production of mill stock is accomplished by less picturesque methods than enter into the production of roofing slate but it is, in the main, relatively more efficient because of the increased use of machinery for handling and for finishing. Mill stock can be classified into two categories as far as difference in production method is concerned: structural slate and blackboards. The significant difference in operation is caused largely by the nature of the rock used for each product with the best and easiest cleaved rock being reserved for blackboards to permit the splitting of large slabs to as little as 1/2 in. in thickness. Structural stock, on the other hand, is split into panels no thinner than 11/2 in. and

Jan 1, 1952

By Y. Nakada, U. F. Kocks, B. Chalrners

THE orientation dependence of work hardening has previously been studied over the entire range, i.e., including special orientations of high symmetry, in aluminum1-3 and silver.* The differences between various orientations are substantial, and the trend is the same in all fcc crystals. However, there are quantitative differences in behavior between aluminum and silver at room temperature, particularly in the (100) orientation. While many experiments on gold have been reported,5'9 none included the special orientations. We therefore undertook tension tests on gold crystals of the axial orientations (100),(110), (Ill), (211), and, as a representative of single slip, one whose Schmid factor was 0.5 (hereafter referred to as m = 0.5). Single crystals of dimensions 1/4 by .1/4 by 6 in. were grown from the melt1' at a rate of 4 in. per hr, using gold of 99.99 pct purity obtained from Handy and Harman. A growth rate of 1/8 in. per hr, or a purity of 99.999 pct,ll produced no difference in results. The crystals were annealed at 1000°C in air for 24 hr and furnace-cooled down to room temperature, after which they were electro-polished in a solution of potassium cyanide (40 g), potassium ferrocyanide (10 g), soda (20 g), and enough distilled water to make 1 liter of solution, at a current density of 0.02 amp per sq mm. After 2 or 3 hr, a very smooth surface was obtained by this method. Nine m = 0.5, two (loo), one (110), three (Ill), and one (211; crystals were tested at room temperature in a floor-model Instron machine at a tensile strain rate of 0.5 pct per min. The accuracy of the stress measurement was k10 g per sq mm up to 500 g per sq mm, k2 pct for higher stresses. The strain measurement was accurate to t2 pct. The scatter of stress at a given strain among the crystals of the same orientation was small, *5 pct being the largest. The representative stress-strain curves for various orientations are shown in Fig. 1. Table I summarizes the work-hardening parameters as used by seeger.12 Results of other investigators are also included in this table for comparison. There are no previous data for the corner orientations. Values for m = 0.5 crystals agree fairly well with those of Berner. Tm is defined as the stress at which the stress-strain curve begins to deviate from linearity of Stage 11. However, in practice this is a very difficult value to estimate because each investigator has a different idea of linearity. Therefore, the comparison with the values of other investigators may not be valid. In the present experiment, (100) crystals had the highest 111, followed by (111) crystals. The work-hardening rate in Stage I1 was highest for the (111) crystal followed by the (100) crystals. Our value for 0x1 of m = 0.5 orientation agrees very well with those of other investigators. 1) Single-Slip orientation (m = 0.5). These crystals were oriented so that the primary-slip vector was contained in one side face. The dimension perpendicular to this side should then not change if single slip indeed takes place. Within the accuracy of measurement, this dimension did not change during the deformation. Since the accuracy is k0.2 pct, the amount of secondary slip is less than 0.7 pct of the slip on the primary-slip system at 30 pct tensile strain. This is in conformity with the results obtained by Kocks" for aluminum crystals. The tensile axis moved toward (211) during the deformation. Slip bands, Fig. 2(a), were very fine and closely spaced. Some deformation bands were observed. There were no clear-cut cross-slip traces such as the ones observed on aluminum m = 0.5 crystals. 2) (111) Crystals. The orientation of the tensile axis was stable during the deformation. From this observation, one can deduce that at least three slip systems must have operated, and probably all six because the remaining three all have cross-slip relation to one of the first three.' It was very difficult to observe the slip markings. Consequently, we could not confirm by this method that six systems were operative during the deformation. At high strains (above 50 pct shear strain), this orientation had the highest stress-strain curve. At 80

Jan 1, 1964

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By Walter R. Hibbard, George H. Eichelman, William P. Saunders

INTEREST in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,1 has resulted in the application of similar heat treatments to other eutectoid transformations. Studies2.3.4 of the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5,6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported&apos; as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. PREPARATION OF ALLOYS The copper-silicon alloy equilibrium diagram is shown in Fig I. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutectoid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct). Smith5 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker&apos;s commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.7 Following the casting techniques of Krynitsky, Saunders and Stern,8 the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under the melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X ¾ in., was annealed at 750°C for 21 brand furnace cooled. About 1/16 in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. methods.9 The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1948

By James J. Halbouty, Michel T. Halbouty

Drilling activity in the South Texas area, which includes the South Corpus Christi and Laredo districts, showed a marked decline during 1941 from that of the preceding year. The rate of new discoveries, however, &apos;compared favorably with exploratory results of 1940 because of the many new productive sands opened in existing fields. South Texas completions for 1941 were about 12.3 per cent below the 1940 figure, compared with an increase of approximately 5.5 per cent in the total number of completions in the United States during 1941 over the 1940 total. During the year, 1452 wells were drilled in this area; of these, 1205 were drilled in or as extensions to the proven fields, and 247 were rank wildcats drilled in search of new producing pools. The comparable 1940 figures were: 1320 field or extension wells and 336 rank wildcats, a total of 1656 completions. This represents a decline in 1941 of approximately 8.7 per cent in proven-area wells, and of about 26.5 per cent in rank wildcats. It must be stressed that wells that were considered rank wildcats at the beginning of operations, but which opened production later classified as additions to existing fields, are not regarded as rank wildcats in this and previous annual reports on this same area. These wells are classified as semiwildcats (Table 2). There were 13 new oil or distillate fields and 4 new gas areas opened during the year, as listed in the next column. This listing represents a decline of 32 per cent from the 25 new areas found during the previous year, and to a great extent can be attributed to the 26.5 per cent decline in wildcatting. The rate of new discoveries based on the 247 wildcats was 14.5 to I, which compares somewhat unfavorably with the 13.4 to I ratio obtained in 1940 (Table 5). Dry wildcats totaled 230. The proof of the prolific character of the South Texas area as a source of petroleum reservoirs is to be found in the fact that of the 1205 field or extension (semiwildcat) wells completed during the past year 61 opened production from new sands or found crude in formerly distillate-producing sands. The 1940 total of 1320 such wells accounted for 50 horizons that provided either new production or crude in distillate sands, and in this respect the 1941 rate of discovery shows to greater advantage, the ratios for new sands being 19.7 to I for 1941 and 26.4 to I for 1940. The 1205 field or semiwildcat wells completed in 1941 resulted in 926 oil or dis-

Jan 1, 1942

By James J. Halbouty, Michel T. Halbouty

Drilling activity in the South Texas area, which includes the South Corpus Christi and Laredo districts, showed a marked decline during 1941 from that of the preceding year. The rate of new discoveries, however, &apos;compared favorably with exploratory results of 1940 because of the many new productive sands opened in existing fields. South Texas completions for 1941 were about 12.3 per cent below the 1940 figure, compared with an increase of approximately 5.5 per cent in the total number of completions in the United States during 1941 over the 1940 total. During the year, 1452 wells were drilled in this area; of these, 1205 were drilled in or as extensions to the proven fields, and 247 were rank wildcats drilled in search of new producing pools. The comparable 1940 figures were: 1320 field or extension wells and 336 rank wildcats, a total of 1656 completions. This represents a decline in 1941 of approximately 8.7 per cent in proven-area wells, and of about 26.5 per cent in rank wildcats. It must be stressed that wells that were considered rank wildcats at the beginning of operations, but which opened production later classified as additions to existing fields, are not regarded as rank wildcats in this and previous annual reports on this same area. These wells are classified as semiwildcats (Table 2). There were 13 new oil or distillate fields and 4 new gas areas opened during the year, as listed in the next column. This listing represents a decline of 32 per cent from the 25 new areas found during the previous year, and to a great extent can be attributed to the 26.5 per cent decline in wildcatting. The rate of new discoveries based on the 247 wildcats was 14.5 to I, which compares somewhat unfavorably with the 13.4 to I ratio obtained in 1940 (Table 5). Dry wildcats totaled 230. The proof of the prolific character of the South Texas area as a source of petroleum reservoirs is to be found in the fact that of the 1205 field or extension (semiwildcat) wells completed during the past year 61 opened production from new sands or found crude in formerly distillate-producing sands. The 1940 total of 1320 such wells accounted for 50 horizons that provided either new production or crude in distillate sands, and in this respect the 1941 rate of discovery shows to greater advantage, the ratios for new sands being 19.7 to I for 1941 and 26.4 to I for 1940. The 1205 field or semiwildcat wells completed in 1941 resulted in 926 oil or dis-

Jan 1, 1942

By A. H. Daane, B. J. Beaudry

The yttl-irtm-nickel system has been investigated by metallo-graphic, thermal ard X-ray methods. There are nine intermetal-lic compounds present: Y3Ni, Y3Ni,, YNi,, YNi,, Y,Ni,, YNi,, and Y,Nil, which rodergo peritectic decomposition and YNi and YNi, which melt congruently. There are eutectics at 34.8, 57.5 and 93.3 at pct Ni which melt at 805°, 950 and 1285 C, respectively. Crystallographic data are given for YNi, YNi,, YNi,, YNi5and Y,Ni,. The terminal solid solubility is low. In recent work by Fisher and Fullhart&apos; in which yttrium crucibles to be used for containers of uranium-chromium eutectic were clad with a high nickel steel, a low melting phase formed where the yttrium was in contact with the steel. To investigate the cause of this phenomenon, Daane, et al. made a survey study of yttrium systems with chromium, manganese, iron, and nickel and found an 18 wt pct Ni (weight percent) alloy to melt at approximately 950°C. voge13 in a study of the systems of cerium, lanthanum, and praseodymium with nickel found six compounds of the same formula in each system, i.e., R3Ni, RNi, RNiz, RNi3, RNi4, and RNi5. Since there is a great similarity between yttrium and the rare earths, compound formation was likely to occur also in the yttrium-nickel system. voge13 observed that the ability of transition metals to form compounds with the rare earths diminishes in the order nickel, cobalt, and iron while no compounds are formed with manganese, chromium, and titanium. Available data on yttrium systems with these elements indicate similar behavior, except that a slightly greater tendency toward compound formation is apparent. Simple eutectics with limited solid solubility have been found in the yttrium-titanium4 and yttrium-chromium5 systems, but at least one compound is present in the yttrium-manganese system.&apos; In the case of yttrium-iron, at least three compounds are present,5 while only two are present in the cerium-iron,&apos; and no compounds are present in the lanthanum-iron5 system. On the basis of both the trend in the alloying behavior of yttrium and rare-earth metals with the first transition series metals and the large number of compounds in the cerium-nickel system, one might expect six or more compounds to form in the nickel-yttrium system. A consideration of Hume-Rothery&apos;s rules of alloying based on size factor, electronegati-vity, and valence predicted low terminal solid solubility and possible compound formation. The present study was undertaken to confirm these predictions of

Jan 1, 1961

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,&apos; has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker&apos;s commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.&apos; Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By David L. Holt, Walter A. Backofen, Anwar-ul Karirn

ANNEALING the binary alloy, Mg-0.5 wt pct Zr in a hydrogen atmosphere results in extensive precipitation of zirconium hydride. The morphology of these precipitates has already been investigated.lm3 Squires, Weiner, and phillips4 found, following creep testing of the hydrided alloy at 450" and 500°C, that hydride denuded zones formed along grain boundaries that were aligned approximately normal to the tensile axis. Zone formation was attributed to diffusional creep by magnesium transport down the prevailing stress gradients.4&apos;5 Recently, electron microprobe analysis by Karim, Holt, and Backofen6 showed the zones indeed to be zirconium-free and furthermore it was shown that in compression, zones formed along boundaries approximately parallel to the stress axis. Thus it was confirmed that the zones are formed by diffusional creep. Typical zone-formation is shown in Fig. 1. Karim, Holt, and Backofen also measured the con- tribution to the total strain, from diffusional flow, slip creep, and grain boundary shear: results showed that diffusional strain tends to saturate with increasing imposed strain, while grain boundary shear eventually becomes the dominant deformation mode. It was suggested in explanation that the precipitate-denuded zones are soft and easily sheared, such deformation contributing to the grain boundary shear measurement. A point to be emphasized is that the Mg-0.5 Zr alloy was not superplastic for the index of strain rate sensitivity of flow stress, m = a log log 6 was only 0.25. It was recognized that diffusional creep in a poly crystalline aggregate must be accompanied by boundary shearing.&apos; The suggestion was that the non Newtonian-viscous character of diffusional creep in the Mg-0.5 wt pct Zr alloy is due to resistance to sliding of boundaries lying approximately parallel to the tensile axis.= The work described in the present note should be seen against the above background for it represents initial efforts to observe in a similar way diffusional creep in a superplastic alloy. Previous work with the ternary-alloy Mg-6 Zn-0.5 Zr, pellet extruded, showed it to be superplastic however it does not contain resolvable precipitates to act as internal markers for diffusional creep. Also the fine grain size of the alloy (0.5 p) made conventional metallography rather difficult. Solubility relationships in the Mg-Zn-Zr system are not well known, however making reasonable guesses about the probable phase diagram of the ternary, Mg-Zn-Zr, various heat treatments were attempted to produce hydride precipitation. Finally a 16-hr anneal at 495&apos; in hydrogen was found to pro-

Jan 1, 1970

By J. Spotts McDowell

Ackowledgments........................... 5 Introduction............................. 5 The Silica Minerals. Stability Relations......................... 6 Optical Properties........................ 9 Density.............................. 10 Melting Points....;..................... 10 Thermal Expansion..................,..... 10 Solubilities............................ 12 Identification of Cristobalite and Tridymite.............. 12. The Silica Refractories. Raw Materia1........................... 13 American Deposits....................... 13 Properties Determining Usability................ 15 Expansion on Heating..................... 16 Texture........................... 17 Silica Brick............................ 17 Manufacture........................... 18 Properties of Silica Brick .................... 19 Analysis ......................... 19 Density......................... 19 Porosity......................... 20 Strength....................... 21 Melting Point....................... 22 Specific Heat....................... 22 Thermal Conductivity................... 23 Expansion........................ 24 Effect of Rapid Temperature Change.........:... 26 Constitution......................... 26

Jan 1, 1918

By N. Arbiter, C. C. Harris

Analysis of ball and pulp flow in ball mills indicates that three factors may become critical with increasing mill diameters: ball size, fraction critical speed, and average pulp flow velocities. Ball diameters may need to be decreased and fraction critical speeds increased with ores which show decreased breakage rate coefficients above 1.2 mm (14 mesh). With 5.5-m (18 ft) and larger mills at higher circulating loads, pulp flow velocities may become capacity limiting and also may limit increases in ball mill diameters.

Jan 1, 1985

By R. W. Smith, R. J. Charles

Fractions of glass particles in the size range 0.5 to 5.0 µ were prepared by an elutriator that operates in a centrifugal field. Although mean sizes of commercially graded abrasive powders were ten times greater than those of samples prepared by the elutriator, frequency size plots for elutriator samples compared favorably. Efficiency of separation was low and amounts of material recovered by the elutriator were small, but the method should find use in preparation of small amounts of sized materials for laboratory investigations.

Aug 1, 1956

By I. P. Pardee

In our mixture at Musconetcong Iron Works we have an exceedingly hard, dense, magnetic ore, which contains some iron pyrites. The sulphur runs from 0.5 to 1.5 per cent. To prepare this ore better for the furnace, and with a view of making a softer iron, we tried roasting the ore in a Gjers kiln. When it worked well, the improvement in the iron was very perceptible ; but the ore was continually sintering and forming scaffolds across the bosh of the kiln.

Jan 1, 1887

By H. I. NORTON, H. O. Hofman

ZINC smelters in the central western. States have established a very high standard of purity for blende-concentrates, viz., zinc 60, iron less than 3, and lead less than 1 per cent. The very low percentage of iron is made possible by the blende containing less than 0.5 percent of isomorphous iron sulphide and by the sparing occurrence of pyritic material in the large blende-deposits of southwestern Missouri and southeastern Kansas. The blende in these districts occurs in sub-Carboniferous limestone, and is associated with chert, residual clay, calcite, pyrite or rnarcasite and bitumen. The different minerals are coarse and therefore readily separated by mechanical washing from the blende, with the exception of pyrite and marcasite, as blende has a specific gravity of from 3.9 to 4.1, marcasite, from 4.85 to 4.90, and pyrite, from 4.95 to 5.10. The common procedure of dressing the ores is to crush in a breaker, size in a trommel with 0.5-in. holes, pass the over-size through roughing-rolls and then jig the ore, now reduced to 0.5 in. maximum size, in roughing multiple-sieve jigs. The products of these are waste-tailings, sine-discharge coarse concentrates, side-discharge coarse middlings and bottom-discharge fine middlings. The coarse concentrates are sent to the market. The coarse middlings are crushed in middlings-rolls and brought back into the system by feeding into the main trommel. The fine middlings are cleaned upon finishing-jigs. Any pyrite or marcasite present follows the blende and increases the percent-

Mar 1, 1905

By W. S. Ayres

I. INTRODUCTION. THIS cavern was discovered Oct. 22, 1904, by Mr. Charles H. Deutschman, in company with whom I made, May 29 to June 3, 1905, at the request of Mr. Howard Douglas, Superintendent of the Canadian National Parks, the first exploration of it for the Canadian government. The results were stated in a paper, orally presented, with lantern-views from my photographs, at the British Columbia Meeting of the Institute, Victoria,, B. C., July 5, 1905.* The present paper embodies also the results of a second examination, made Oct. 25 to 29, 1905. The accompanying map, Fig. 1, will serve as a guide to the following description. II. LOCATION. The cavern is situated at snow-line, at the head-waters of Cougar creek, on the west slopes of the Selkirks, about 2 miles north from Ross Peak water-tank, and 5.5 miles west from Glacier House, on the main line of the Canadian Pacific Railway. It was then reached by an arduous climb from the water-tank, up the ravine of Cougar creek, for 8,000 ft. (2,000 ft. of altitude) over rock- and snow-slides, and through a thick tangle of alders. But an easy and very picturesque trail has, during the past summer, been opened by the government from Glacier House. Figs. 2, 3 and 4 represent views, not heretofore published, of the grand scenery of this region, so rapidly becoming the-object of attraction to thousands of tourists from all parts of the world. These views, as well as those shown in. Figs. 5, 6, 7, 8

Jan 1, 1907