Search Documents

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. TABLE 1 .-Typica.1 Chemica1 Analysis [PER CENT H20,1100F ............................................ 0.0'2 Ignitionloss ............................................. 43.56 MgO .................................................. 19.19 CaO .................................................... 29.07 FezO .................................................... 0.39 A1203 .................................................... 1.94 FezO .................................................... 0.39 A1203 .................................................... 1.94 ..................................................... 5.75 SO2.. .................................................. Tr.] Rock was carried by 12-yd. dump trucks to a 42-in. gyratory crusher set at 6 1/2 in. The product of the primary crusher was taken by a belt conveyor to a double-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1937

By John Langton

In determining what kind of pourer should be adopted for the works of the Moctezuma Copper Co. at Nacozari, Sonora, Mexico, certain considerations imposed by local conditions had to be taken into account. Water.—During most of the year the water-supply is abundant for all purposes, but it dwindles rapidly when the dry season sets in, reaching a minimum flow which is entirely undergrouad. It was evident, that with the greatest care in keeping down the unavoidable loss of water in milling and smelting, these operations and hence the capacity of the works mould ultimately be limited for about two months of the year by the small watersupply available at the period of minimum flow. Transportation.—The nearest railway terminus was in Arizona, at the international boundary-line; and the price of supplies at that point would be enhanced at Nacozari by the additional cost of a 90-mile wagon-haul. During the rainy season, transport to Nacozari was much impeded, and at times made impossible, by the condition of the roads. Hence, to insure continuous operation at the works, it would be necessary to provide for hauling the year's supplies, including fuel for power and coke for smelting, in less than eleven months. In other words, the average freight delivered daily at the works should be at least 10 per cent. more than the average daily consumption. For moderate quantities of freight, pack-carriage by burros is astonishingly cheap. But it has a capacity-limit which is generally very soon reached. A 200-lb. load, and 10 miles a day, 5 with and 5 without load, is the full capacity of a burro. This means one burro per ton-mile of the round trip; and,

Jan 1, 1904

By C. E. Arnold

A BRIEF description of this installation was included in a recent paper by H. Kenyon Burch.1 The purpose of the present paper is to amplify Mr. Burch's description, as it is felt by the writer that the subject merits more than passing attention. In making a comparison between the common method of hoisting men in mine shafts, and elevator practice in high buildings, the former shows to great disadvantage both as regards safety measures and smoothness of operation. It is surprising that in view of the inducements offered, the step of applying the building equipment direct to the mine shaft has not been taken before, as in many respects the conditions of service are similar, and the objects to be attained are identical. Even without doing this, it is certain that safety to life and limb in the usual method of hoisting men underground can be greatly enhanced by the application to the mine hoist, of some of the features of the building elevator. In the case under consideration, the elevator cage runs in a vertical, concrete-lined shaft compartment 5 ft. 11 in. by 5 ft. 6 in. (1.8 by 1.68:m.) in section and 585 ft. (178 m.) deep, while the counterweight runs in the pipe and ladder compartment of a twin shaft 102 ft. (31 m.) distant. The section of the division of this compartment occupied by the counterweight measures 2 ft. 4 ¼ , in. by 3 ft. 10 ½ in. (0.72 by 1.18 m.), and the counterweight is made in the form of a small cage which. suffices to carry two men for the purpose of making inspections or repairs in the pipe and ladder way.

Jan 12, 1917

By D. W. Fuerstenau

Measurement of zeta potentials is a useful tool to study the surface chemistry of minerals under flotation conditions. Because there is continued interest in this approach, the apparatus for obtaining zeta potentials of nonconducting solids by the streaming potential method is outlined here. Fig. 1 illustrates the streaming potential apparatus. The streaming potential cell or plug consists of two 24/40 standard ground joints (4) joined with a piece of pyrex tubing 60 mm long and 12 mm in diam (5). The electrodes are made of bright platinum disks 19 mm in diam and 1 mm thick through which 0.5-mm holes have been drilled (6). To the surface of each is welded a piece of 80-mesh platinum gauze. Each electrode is permanently mounted on the ends of the inner parts of the two standard joints by means of a platinum wire (7) which connects it to the tungsten seal at the end of the cell (8). For ease in cleaning and handling the apparatus, the streaming cell is fastened to the 500-ml reservoir flasks (1) by means of two 18/9 ball and socket joints (2). This particular arrangement permits passage of the solution in either direction through the plug of particles. Flow of solution can be stopped by a stopcock (3). One of the reservoir flasks has a large opening to permit insertion of either a thermometer or a pair of electrodes for measuring pH of solutions within the system. In making the experiments, the plug is filled with 48 to 65-mesh particles, but a layer of 28 to 35-mesh particles is placed at each electrode to prevent any of the finer particles from passing through holes in the electrodes.

Aug 1, 1956

By Charles E. Locke

The little stamp-mill in the mining laboratory of the Massachusetts Institute of Technology and the work done by it have been well described by Prof. R. H. Richards and E. E. Bugbee in a paper read at the Albany meeting of the American Institute of Mining Engineers, February, 1903.' As run for student class-work the mill contains a feeder, stamps, plate, and vanner. Results in the past indicate that the work of these machines is just as efficient as that of a regular mill handling the same class of ore. It has been the custom to obtain ore principally from Nova Scotia, mainly because it is the nearest source of supply, and also because there is a considerable saving in freight-cost as compared with other districts. The gold in Nova Scotia ores is notoriously coarse, and for this reason it is almost impossible to obtain satisfactory results by sampling and fire-assay, unless an extremely large lot of ore is crushed and all of the contained gold pellets are saved. A very interesting and most extraordinary example of this fact has been presented by a recent run in the Technology stamp-mill. Since the capacity of the mill is about 60 kg. per hr., and since in about 5-hr. run the students in any one section have an opportunity to make the necessary study of machines, it usually happens that several runs are made from one lot of ore. When the shipment is received it is first dried and weighed, put through the Blake breaker, set at 1 or 1.5 in., and the crushed product is piled in a cone on the sampling-floor. When the crushing is completed the ore is usually stored away in barrels for future use; it is aimed to have each barrel of

Jan 1, 1914

By T. M. Williams

DURING the year just ended we have had three great fires in the mines in the Wilkes-Barre district. One at the Empire Colliery, one at the Prospect shaft, and the other at the Baltimore old mine. It is proposed in this paper to give a brief history of the fire at the Empire Colliery, and the methods employed in extinguishing it. The fire was first discovered breaking out in the air-stack, alongside what is known as the " Kidder Plane," about one o'clock on the morning of December 31st, 1873. Subsequently it was ascertained that the fire originated in the return airway somewhere near the steam boiler, located inside the mine, near the head of No. 5 slope. The coal from this slope was hoisted to the shaft gangway, at a point nearly four thousand feet distant from the foot of the shaft. As there were from four to five hundred mine cars hoisted per day from this slope the steam boilers were located at this place. The mines being of considerable extent required a large volume of pure air for ventilation, and no fan having been erected at this slope at the time, the heat from the boiler was made use of to assist ventilation, by conveying the return air from No. 5 slope into the large airway made from these boilers to the surface through the old "Kidder slope" to the stack where the fire was first discovered. The length of this slope or airway was about one thousand feet, with a sectional area of about sixty feet. The quantity of air passing through it must have been over sixty thousand cubic feet per minute

Jan 1, 1875

By T. M. Williams

DURING the year just ended we have had three great fires in the mines in the Wilkes-Barre district. One at the Empire Colliery, one at the Prospect shaft, and the other at the Baltimore old mine. It is proposed in this paper to give a brief history of the fire at the Empire Colliery, and the methods employed in extinguishing it. The fire was first discovered breaking out in the air-stack, alongside what is known as the " Kidder Plane," about one o'clock on the morning of December 31st, 1873. Subsequently it was ascertained that the fire originated in the return airway somewhere near the steam boiler, located inside the mine, near the head of No. 5 slope. The coal from this slope was hoisted to the shaft gangway, at a point nearly four thousand feet distant from the foot of the shaft. As there were from four to five hundred mine cars hoisted per day from this slope the steam boilers were located at this place. The mines being of considerable extent required a large volume of pure air for ventilation, and no fan having been erected at this slope at the time, the heat from the boiler was made use of to assist ventilation, by conveying the return air from No. 5 slope into the large airway made from these boilers to the surface through the old "Kidder slope" to the stack where the fire was first discovered. The length of this slope or airway was about one thousand feet, with a sectional area of about sixty feet. The quantity of air passing through it must have been over sixty thousand cubic feet per minute

By John W. Tieman

Coal is a term applied to vegetable matter which, through geological processes of heat and pressure, has had both its physical and chemical properties changed. Because its chemical composition is variable, geologists classify coal as a rock rather than a mineral. Peat represents the initial stages in the development of coal, although not classified as coal itself. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness of coal determines the maintenance cost on coal handling equipment; the specific gravity of coal determines the coal preparation techniques used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent upon the chemical constituents that make up coal, and thus all properties are interrelated. Specific Gravity The specific gravity of a body is the ratio of the weight of the body in air and the weight of an equal volume of water. The specific gravity of pure coal ranges between 1.25 and 1.70, generally increasing with rank. The most important use of this physical characteristic is the part that it plays in the cleaning of coal by wet wash methods. The basic principle on which these operate is that the specific gravity of coals differs from their associated impurities and that there is a relationship between the velocity of the fall of particles in water and their density. Since the specific gravity of slate is around 2.5 and pyrite is about 5.0, pyrite and slate will fall to the bottom of a container filled with water more rapidly than coal. If the water is given a pulsating motion by

Jan 1, 1973

By G. A. Reinhardt

THE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4 in. (14.5 cm.) square bloom to a ¾ in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900 ° to 950° C. and cooling slowly in mica. The test bars were tempered by heating to 825° to 875° C., quenching in water, and drawing to 515° to 535° C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. ULTIMATE STRENGTH, ELONGATION, LB. PER SQ. IN. PER CENT. IN 4 IN. NOT LESS THAN Annealed specimens 78,230 to 92,450 18 Tempered 120,000 to 149,350 9 After experience oil this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850° to 900° C. and cooling in still air; the annealing, in heating to 850° to 900° C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were:

Jan 7, 1919

Endurance Properties of Non-ferrous Metals Discussion of the paper of D. J. McADAM, JR., presented at the Syracuse Meeting of the Institute of Metals Division and issued, as Paper No. 1506-E, with Mining AND METALLURGY, October, 1925. H. F. MOORE,* Urbana, Ill. (written discussion).-This paper says that the results of tests of some non-ferrous metals made at the University of Illinois and in the testing laboratories at McCook Field are abnormal when they do not agree with results obtained by the author. The writer can see no inherent reason why results of the type uniformly reported in this paper are any more normal. The knee of the stress-cycle, or S-N, diagram comes at different lengths of life for different metals. For steel, the knee occurs after from 1,000,000 to about 4,000,000 cycles, and for some non-ferrous metals not before 20,000,000 of 30,000,000 cycles. The writer can see nothing inherently abnormal in finding certain nonferrous metals for which the knee of the stress-cycle curve occurs at 1,000,000,000 cycles or higher. The writer has had experience with both the cantilever and the rotating-beam testing machine, and thinks that the chance of whipping action in the cantilever machine is a more serious handicap than the action the author has pictured. Furthermore, the writer questions whether the author has shown the existence of a clearly marked and definite endurance limit for all the non-ferrous metals he has tested including the following: Nickel (CT and A-16, Fig. 1), monel (CS-5.5 and BK, Fig. 2), bronze (F and CK, Fig. 4), aluminum bronze ( BJb-1, Fig. 6).

Jan 12, 1925

George W. Maynard, New York, N. Y.:—It is well known that there are many magnetite-mines of which the ore is too low-grade for direct use in the blast-furnace. For carrying out the sintering process, the preliminary step, in the case of magnetites, is the separation of the ore from the gangue by magnetic concentration. The resulting fine-grain product is very objectionable in the blast-furnace, and when used must be a very small percentage of the charge. The sintering process has saved the situation by furnishing a product which is absolutely ideal on account of its cellular structure. (In reply to questions by W. J. Tudor, and Joseph W. Richards, the following additional information was given by Dr. Maynard.) The percentage of iron in the product is determined entirely by the degree of concentration of the raw material and is practically not increased by the sintering operation. The magnetic concentrates at Port Henry and at the Benson and one or two other mines contain from 65 to 67 per cent. of metallic iron. The cost of sintering is from 39 to 41 cents per ton of product, including superintendence, depreciation, and repairs. The itemized figures are about as follows : Mixing (including labor), 24; power, 9; ignition, 5; repairs, 3; total, 41 cents. Prof. J. W. Richards, South Bethlehem, Pa.:—From a metallurgical standpoint I question the accuracy of the statement on p. 374: " C.—An increased reducibility of the iron so treated. (This has been conservatively estimated as 5 per cent. better than the best available ore.)" It seems to me that when a material is' sintered in this way, the constituents present, as lime, silica, and alumina, have a chance to form a compound with the iron oxide; that such a compound, if formed before the material goes into the blast-

Jan 1, 1913

By E. W. Mehal, R. H. Cox

A planar Gunn oscillator was developed for use in a monolithic microwave integrated circuit. The device was designed to operate in the frequency range of 20 to 30 GHz with a continuous wave output. Selective epitaxial deposition was used to form the n+n-n+ device structure in (111)-B semi-insuluting GaAs. The active n- region was about 5 µ thick and was doped to about 2 x 1015 electrons per cu cm by the reactor background. The mobility was -5000 sq cm v-1 sec-1. The n+ epitaxial deposits were doped to 1 x 10" electrons per cu cm using S2Cl2. Planarity of the three DURING the past few years, new microwave devices in discrete form have been developed utilizing GaAs. The next logical step is to combine these devices in a successive deposits was quite good; total overgrowth was less than 1 µ. Metal ohmic contacts were applied to the n+ or n- regions using a Ag-In-Ge alloy. The n+n-n+ devices had symmetric IV characteristics and could be operated C. W. for both directions of device bias. Metal ohmic contacts made directly to the n-region always Produced asymmetric devices. C. W. operation was obtained over the 22 to 28 GHz frequency range. The best performance obtained was 1.5 mw C. LV. output at 28 GHz. microwave integrated circuit. A potential application would be a radar receiver operating in the millimeter wavelength region. The key component in such an integrated circuit is a microwave oscillator, recently described by Gunn.1, 2 Under the influence of a large electric field, high-resistivity GaAs exhibits a bulk negative resistance, and high-frequency current oscillations result. Since relatively high voltage and

Jan 1, 1969

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By V. B. Tare, H. Schmalzried

The use of solid electrolytes for determining kinetic paraneters at elevated tevnperatures is pointed out. The reaction rate constant k1 of the phase-boundary reaction during oxidution of iron to wiistite by CO2-CO gas mixtures has been deternined between 850 nnd 975C, using ZrOz(+CaO) as an electrolyte. Values are between 1.4 x 10-a and 5.2 x 10 ole per sq ctn atm. The tzain difficulty is due to mixed potentials arising from side reactions at the electrolyte inteyface. In a number of papers the calcium-doped zirconia electrolyte has been used for the determination of thermodynamic data from measured differences in oxygen activities (or potentials) between two electrodes. The purpose of this note is to suggest the use of this solid electrolyte for kinetic measurements as well. The principle can be seen from Fig. 1. A thin and compact phase II (electron conductor) is fixed on a plate of gas-tight, polished ZrO2(+CaO) (I), which separates two compartments with different oxygen potential. p, is a constant reference pressure of oxygen (1 atm). The electromotive force of this galvanic cell is given by E = RT5 In pep, and pe is the oxygen partial pressure at the interface electrolytephase 11. If phase I1 is in equilibrium with the surrounding gas phase, p, = DR. If pg changes sud- denly to a value pi, p, and therefore the electromotive force, E, change as a function of time according to the phase-boundary reaction rate at the gas phase I1 interface and the transport processes inside phase 11. It is assumed that local equilibrium is established at the boundary electrolytephase 11, that the gas phase shows no concentration gradients, and that the con-

Jan 1, 1967

By J. M. McCormack, R. K. Saxer, J. R. Myers

ThE Knudsen effusion technique was used to determine the chemical activities of copper and platinum in binary Cu-Pt alloys in the temperature range 1542" to 1673°K. Wiebke and Matthes1 previously obtained chemical activities of copper and platinum in this system at 673° and 923°K by the electromotive-force measurement method. They reported that the copper activities exhibited negative deviation from Raoult's law at all compositions. The chemical activities of platinum were found to change from a positive to a negative deviation at 923°K. Myles2 recently studied this system in the temperature range 1265° to 1356°K by means of the torsional-effusion technique. His results indicated that both copper and platinum exhibited negative deviation from ideality at all compositions. The use of the Knudsen effusion technique to obtain the vapor pressure of metals and alloys is well-known.3 In this work, Knudsen cells were fabricated from seamless tantalum tubing of 1-in. OD and 0.020-in. wall thickness; cell bases and covers were cut from 0.010-in.-thick tantalum sheet and welded to the cells in an argon atmosphere. Orifices were drilled and reamed to approximate a knife-edge of 30-deg included angle. Calculation based on Balson's4 derivation showed the orifice to be nearly ideal. All temperature measurements were made with a Leeds and Northrup disappearing-filament-type optical pyrometer at the orifice of the cell, which closely approximated black-body conditions and eliminated the need for emissivity corrections. Details of the experimental techniques used, and the necessary correction factors required during this investigation are essentially those previously described.5,6 Before investigating the Cu-Pt alloys, vapor-pressure measurements were obtained over specimens of pure (OFHC) copper. The pure-copper data5 served to assure the accuracy of the experimental apparatus and technique.

Jan 1, 1967

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.' Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

By R. Taggart, J. W. Barton, G. R. Purdy, J. G. Parr

The constitution and mechanical properties of heat-treated alloys containing up to 10 pct* Ni in Ti have been investigated. The effects of quenching and of various isothermal treatments ale described, and C-curves are presented. The production of the precipitated and the martensitic hexagonal phases on quenching is discussed. MARGOLIN, Ence, and Nielsenl have determined the titanium-nickel phase diagram. A study of the transformations in gas-quenched and tempered powder specimens was made by Polonis and Parr.' Some isothermal transformation work was carried out by Margolin and ~unshah, who determined transformation curves for 4 and 6 wt pct alloys, while Robinson et al.investigated the formation of the w phase in a quenched and tempered alloy, Margolin and Bunshah showed that while a martensitic transformation could be obtained on quench- ing thin sections of a 4 wt pct alloy, a 6 wt pct alloy precipitated a nonmartensitic phase. The present investigation was undertaken to obtain more information on the transformations in quenched, quenched and tempered, and isothermally transformed lump specimens of alloys containing up to 10 pct Ni. Isothermal transformation curves have been determined for 7 and 10 pct alloys and cooling curves have been obtained for quenched alloys containing up to 7 pct Ni. The mechanical properties of 2, 5, and 10 pct alloys were studied, with the object of relating properties to microstructures. EXPERIMENTAL METHODS Alloys containing up to 10 pct Ni were prepared from sponge titanium and spectrographic standard nickel by levitation-melting and chill-casting in a split copper mold. The 5 and 10 pet alloys were prepared from sponge Ti having an as-melted hardness of 115 Vpn. The other alloys were made from a sec-

Jan 1, 1961

By Donald N. Rosenblatt

I would like to commend the author on his description of Pinto Valley's plant, and its interesting innovations. The author's discussion of 18 ft in diameter by 21 ft long primary ball mills (the largest wet ball mills made to date) is of considerable importance to those who have been engaged in the field of studying ball mill liner wear as it relates to various grinding installations. While it is stated that the mills have operated on a fixed tonnage and therefore it has been difficult to determine the best liner pattern, calculations from the data in the paper indicates that for mills 1, 2, 5, and 6, the tonnage per hour varies from a low of 223 for mill No. 1, up to a high of 314, for mill No. 2, while mills 5 and 6 calculate 285 and 246, respectively. Analysis of the wear patterns for the single wave liners used in mill No. 1 as compared to the double wave liners in mill No. 2, suggests that the author's data may tell more than he suspects about liner wear to be expected and thus what should be a best pattern selection from what may appear to be only limited hours of operation. [Fig. A] is a reproduction of author's [Fig. 10], to which wear forecast patterns [F-1 and F-2] have been added. Forecasts are based on many previous studies of large diameter ball mill operations over many years of field service. Calculations from the first-wear pattern provide an initial wear rate of only 13 lb of liner per 100 sq ft of shell liner surface per day, or 0.031 lb per to: ground. However, the second wear pattern is ac-

Jan 1, 1978

By W. E. Thorne

The object of this graphic method is to estimate the weight of the casting, which is to be made from a given pattern, when the cross-section is not a uniform geometrical figure. Such an estimate is a very important guide to the foundryman, who would otherwise guess at the probable weight of a casting of new design, and, in trying to be on the safe side, would probably melt an unnecessary amount of iron. It is also an aid to the designer of a new car-wheel pattern, who must otherwise estimate from general experience the probable weight, have test-wheels made, and correct the pattern afterwards, so as to obtain the weight prescribed. For the method here described, an accurate drawing of the pattern is employed. This gives a closer result than a drawing of the wheel itself, for the following reasons: 1. Calculations based upon the actual dimensions of the wheel involve the erroneous assumption that the specific gravity of the casting is uniform throughout; and upon that basis the calculated weight would be wrong, because the amount of metal poured has shrunk in the mould, acquiring the highest density in the outside chilled portion, and growing less dense through the mottled to the gray portions. 2. Calculations based upon the dimensions of the pattern or " chiller " assume that the cooled metal will not have shrunk, but will have the volume of the pattern and a uniform density. These assumptions, though erroneous, counterbalance each other. For instance, the patterns and the chiller which give a wheel 33 in. in diameter when cold, are respectively 33.5 in. in diameter. This shows a shrinkage for wheel-iron of about & in. (ordinary gray pig is commonly assumed to shrink about 1/8 in.) per foot. Wheels cast in 33.5-in. chillers do not always have the

Jan 1, 1903