Search Documents

By J. R. Long, T. R. Graham

THIS report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. PRELIMINARY WORK In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, 0 to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening, effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By Walter Knox, J. D. Doherty

IN 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. SUMMARY OF RESULTS Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3). 2. The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 1 1.6 per cent to 19.2 per cent. There was a noticeable segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may he a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance I. The removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. With intermittent operation the burning rate was almost always less than the feeding rate. The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. I3). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). GUIDING PRINCIPLES In planning the investigations, the following principles were adopted: Selection of Healing Equipment.-Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By T. R. Graham, J. R. Long

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By J. R. Long, T. R. Graham

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By R. B. Adamson

The fatigue behauior of irradiated copper single crystals is compared to that of unirradiated crystals. Proton or electron irradiation did not substantially change the fatigue-lzj.e, fatigue-hardening-, or slip-line characteristics, while neutron irradiation did appear to alter these parameters. Postfatigue transrrzission electron microscopy did not reveal any marked structural differazces between irradiated and unirradiated specimens. Possible dislocatio~a mechanisnzs to explain the observed behavior are discussed. A LTHOUGH considerable work has been done to ascertain the effects of radiation on the tensile properties of metals (e.g., Refs. 1 and 2), little work of a basic nature has been reported on the effect of radiation on fatigue properties. Since it is known that fatigue properties are sensitive to conditions at the surface of the metal, it was felt that charged particle irradiation, whose penetration into metals is very small, might influence the fatigue behavior. To investigate this surface effect, irradiations with 10 mev protons and 1.5 mev electrons were conducted. The range of 10 mev protons in copper is about 0.236 mm; which is very small compared with the thickness of the specimens used (1.53 mm). The range of 1.5 mev electrons is somewhat larger, on the order of 0.665 mm.4 On the other hand, irradiation with reactor neutrons produces damage throughout the entire specimen, so neutron irradiation can be used to study the effects of bulk damage. The damage introduced by proton and neutron irradiation is expected to con!ist of large interstitial dislocation loops,5 tiny (<25A) vacancy loops," and/or various vacancy-rich regions called depleted zones.&apos; In the case of electron irradiation at about -173°C the damage is expected to consist of isolated Frenkel pairs.&apos; The effect of radiation damage on the fatigue properties of some engineering materials has been reported,g,10 but the results are not clear-cut or consistent. SPECIMEN PREPARATION Zone-refined copper was used to grow single crystals by a modified Bridgeman technique in an inert helium atmosphere. Using a seeding method, single crystals were obtained as bars about 6 in. long with a cross section of 3 by $ in. Immediately upon removal from the split-mold graphite boat in which they were grown, the very soft bars were embedded in a room-temperature setting plastic. They could then be cut into specimen lengths without introducing any long-range damage. Generally, four or five specimens plus one seed were obtained from each bar. The plastic material was dissolved away in acetone and the orientation of each sample was checked by the standard Laue X-ray

Jan 1, 1968

By L. F. Mondolfo

An aluminum-copper 4 pct Cu alloy aged at room temperature for times increasing up to 78,000 hr was annealed at 170°C and the hardness and electrolytic potential determined during retrogression and subsequent aging. It was found that there is a change of behavior with increasing time of aging at room temperature which indicates that, given sufficient time, retrogression disappears and the room-temperature aging tends to progress directly into the high-temperature aging. WHEN an age-hardenable alloy is aged at low temperature after proper quench, changes of properties and structure take place. If this material is then heated to a temperature higher than the previous one, but still well below the solution-treatment temperature, the properties and structure changes produced by the low-temperature aging disappear and the material apparently reverts to the as-quenched condition, ready to undergo aging from the start. This phenomenon is termed reversion or retrogression. First discovered by Cayler3l it has been extensively investigated, as shown by the number of publications listed in the bibliography. From all the information available the following facts emerge: 1) All aeg hardenable alloys can be retrogressed.9 13, 19) 24, 33, 41, 42, 44, 47, 53, 54, 61, 63, 64, 66, 73, 78 2) All the properties changes that take place during aging at low temperature can be retrogressed to a smaller or larger extent.4,5,7,12,19,32,49,50,57,58,60,67,75,76 67, 75, 76 3) Retrogression requires that the temperature be well above the preliminary aging temperature. If the difference between the two temperatures is small, Little or no retrogression takes place.7,20,32,33,41,49 57. 65 4) The larger the difference between the preliminary aging and the retrogression temperature, the faster and more complete is the retrogression.20, 33, 41, 48, 65, 67 5) Retrogression can be produced several times in the same alloy.23, 35,41,57,59 6) The amount of retrogression that can be obtained depends on the aging temperature. Alloys aged at the lower temperatures can be retrogressed the most. The higher the preliminary aging temperature the less retrogression can be produced.20,25,33,37,44,49,54,58 7) Appreciable retrogression after aging at elevated temperatures is possible only if the preliminary aging has lasted a short time. After a certain time of aging at high temerature retrogression does not take place any more,:5,6,9,10,11,21,40,58 8) During retrogression the Guinier-Preston zones redissolve and disappear. The other precipitate

Jan 1, 1960

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2&apos; The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2&apos; The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By R. M. Brick

SEGREGATION can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming. steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-12 per cent Si alloys. The phasial condition implicitly described above-solidification over a range of temperatures with a compositional difference between solid. and liquid-is found in nearly all solid solutions or combinations of solid solutions and eutectics. Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually determinable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be. described first because it is an essential part of the picture. CORING Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus 1, 3, 7 and solidus 2, 5, 8, and where the vertical 1, 4, 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. 1b) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1944

By Alfonso W. Ovalle, Héctor R. Albornoz

INTRODUCTION The El Teniente Mine of Codelco-Chi le has extracted 588 mil lion tons of ore in its 77 year history for a total copper output of 8.800.000 tons. The mine production has been obtained mainly by traditional block-caving where grizzlemen using a hand held lever send ore through long-raises to load trains. At present the mine is about to introduce mechanized block-caving using LHD equipment to extract the primary rock. This paper describes this method which will be tested starting next month by caving an 11.000 square meter block. THE PRIMARY ROCK PROBLEM The secondary enrichment sulfides of the El Teniente ore body have characteristics which makes a standard unmechanized block-caving practice very successful. In the 60&apos;s parts of blocks encountered primary ow in the Teniente 1 and Sub-13 levels which proved to be extremely hard to extract. These foretold the obstacles that arised in the central part of the Teniente 4 level. Preparation of a completely primary 8.100 square meter block started in 1970. Its undercutting was completed by the end of 1972 and by 1973 the problem of mining the primary rock was clearly visualized. The numbers below describe the difficulties in mining this block: -Long-hole drilling rate is 90 m (270 ft) per shift in secondary rock and 37 m (110 ft) in primary. - Undercutting which is completed in 9 shifts in secondary took 180 shifts in the primary block. - Average grizzlymen productivity in secondary is 250 tons per shift while in primary it is only 25-30 tons, both at 343 mm (13 1/2 in. ) grizzly opening. - Powder consumption for secondary blasting increased from 8 grams per ton in secondary to 84 in primary. - The protection pillar between the under- cutting and the production levels was 60% broken in primary while 20% is usual for secondary. - Extraction advanced 5 cm per day in primary while a 50 cm per day rate is the aver- age in secondary. This is the main reason that after 8 years this primary block has a 20% extraction. Secondary blocks take 1.5 to 3 years to complete their extraction. - 80% of the boulders in primary rock are larger than 343 m (13 1/2 in.) with 10-20 % of them larger than 3 meters. -Direct cost of production (preparation, undercutting, extraction and haulage), using the traditional block-caving design for secondary rock, increased 3.5 to 4 times when used in primary rock. The following indicators of Table 1 show the rock characteristics differences.

Jan 1, 1981

By H. F. A. Hergt, K. L. Sutherland, J. Rogers

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By R. M. Brick

Segregation can occur only in cast alloys that solidify over a range of temperatures with a difference in composition of liquid and solid phases within this range (ignoring monotectic systems and chemical reactions as in rimming steels). Thus a pure binary eutectic alloy should show no segregation unless undercooling occurs for one of the solid constituents of the eutectic; e.g., chill-cast Al-I2 per cent Si alloys. The phasial condition implicitly described above—solidification over a range of temperatures with a compositional difference between solid and liquid—is found in nearly all solid solutions or combinations of solid solutions and eutec-tics, Metastable conditions of solidification of these types of alloys cause coring; i.e., a difference in composition between the center of a dendrite and its periphery. This composition gradient can be detected usually only by microscopic examination of etched structures; it is a "micro" effect. The gradient of more immediate industrial concern is that between the center of a cast section and the surface layers. This gross (macro) effect is usually deter-minable only by sampling of the casting at different points, with chemical analyses of each sample. If the compositional difference is of the same type as in coring, the first parts to freeze being enriched in higher-melting-point constituents, and vice versa, the effect is called normal segregation. When what is apparently the first part of the casting to solidify shows a higher concentration of low-melting-point constituents, the effect is called inverse segregation. These macro effects are quite separate from the micro effect, coring, yet the latter must be described first because it is an essential part of the picture. Coring Solid Solution, Ni-Cu The nickel-copper phase diagram is reproduced in Fig. Ia, in which the solid lines represent the equilibrium liquidus I, 3, 7 and solidus 2, 5, 8, and where the vertical I, 4: 8 represents a 55 per cent Cu alloy. Upon moderately rapid solidification, the first dendritic axes of composition 2 (see Fig. Ib) start to form at a temperature somewhat under I. Solidification continues by growth of the dendritic nuclei, but at temperature 4 the increment solidifying is of composition 5. The rapidity of this crystal growth prevents diffusion of nickel and copper atoms from adjusting the composition of the entire dendrite at 5, which it would be under equilibrium conditions. The average composition of a specific dendrite, or the entire solid phase, at temperature 4 might be that indicated

Jan 1, 1945

By J. Rogers, H. F. A. Hergt, K. L. Sutherland

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By Pol Duwez, Paul Pietrokowsky

The crystal structure of the compound TisGeS has been determined from X-ray powder diffraction data. Related silicon and tin compounds have been found to be isomorphous. Unit cell dimensions, axial ratios, and parameters for equivalent atomic positions are given. THERE is, at present, only meager information pertaining to the solid state reactions of titanium with the elements in group 4B of the periodic table (silicon, germanium, tin, and lead). The only two compounds whose crystal structure has been established are TiSi² and TiGe² (references 1 and 2 respectively). These two compounds are isomor-phous and have an orthorhombic symmetry D242h— Fddd. The titanium-rich regions of the constitution diagrams of titanium-silicon, titanium-tin, and titanium-lead have been investigated by Craighead et al.³ While valuable information concerning the alpha solid solubility of these three elements in titanium was obtained, no light was shed on the existence or nature of the titanium-rich compound in these systems. The present study is concerned with the crystal structure of the intermediate phases Ti5Si ?, Ti³Ge³, and Ti5Sn³, which were found to be isostructural. The alloys were prepared by mixing the pure metal powders in the desired proportions, pressing the mixture into pellets, and melting them in an electric arc furnace in the presence of a helium atmosphere.& After melting, the specimens, weighing approximately 5 g, were sealed in evacuated quartz vials, homogenized at 1038°C for three days, and quenched from that temperature. Powder diffraction patterns were made with a 143.2 mm diam Debye-Scherrer X-ray camera in which the Ievins and Straumanis film arrangement was utilized. Filtered copper radiation was used throughout the entire investigation. A study of the powder patterns of a series of alloys of various compositions indicated the presence of a compound around a composition corresponding approximately to a ratio of 3 titanium to 2 silicon, germanium, or tin. From a visual examination of the diffraction patterns, it was evident that the silicon and germanium alloys were iso- morphous. For small angle reflections, the powder pattern of the tin compound was analogous to that of the silicon and germanium compounds, but after the first ten reflections, the similarity was no longer clear. The powder pattern of the germanium compound was selected for indexing, since it exhibited a weak small angle reflection and clearly resolved doublets in the back-reflection range. Good agreement between observed and calculated values of (1/d)² was found by indexing the pattern on the basis of hexagonal symmetry. For the hexagonal system:

Jan 1, 1952

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1941 are available at Institute headquarters, unless otherwise noted They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS TECHNICAL PUBLICATIONS in Classes A-Metal Mining, 13-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every other month TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysics, are issued as separate pamphlets An Institute member is entitled to one copy of any printed TECHNICAL PUBLICATION or CONTRIBUTION Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes CONTRIBUTIONS and other TECHNICAL PUBLICATIONS will be sent upon request A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page, minimum charge, 25¢ Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1 25 domestic, $1 35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2 50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7 80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers) MINING TECHNOLOGY, $6 per annum domestic, $6 60 foreign (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6 60 foreign Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY Is mailed each month A member is entitled to one volume a year on his membership and he may purchase for $2 50 one copy of a volume not already received, additional copies of the same volume, $5 Nonmembers in the United States may purchase the volumes listed at $5 each, outside of the United States and its possessions, $5 6o Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 500 each to members, to nonmembers 50¢ current issue and $1 each, back issues Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4 00 foreign.

Jan 1, 1941

By D. Weinstein, F. C. Holtz

AS a possible method of improving the elevated temperature strength properties of zirconium, an investigation was initiated on the feasibility of producing a dispersion-strengthened material. Because of the high reactivity of zirconium, its high solubility for oxygen, and the stability of the Zr-0 solid solution, the major problem in such a development is choice of a suitable dispersant. Thus, in the present investigation we were concerned primarily with the stability of various dispersants in the zirconium matrix. The experimental procedure consisted of blending powders of zirconium and a dispersant, followed by cold compaction and extrusion. The best available source of -325 mesh zirconium powder contained between 1500 and 3500 ppm Oz; to this material, powders of zirconium carbide (5 p max), vanadium carbide (5 p max), alumina (0.03 p average), lan-thana (0.8 to 2 p), ceria (0.8 to 2 p), yttria (0.8 to 2 p), calcia (44 p rnax), or thoria (0.6 to 0.8 p) were added in amounts of 7 vol pct and compacted at 65 tsi. A cylindrical compact having a density between 70 and 80 pct of theoretical and dimensions of 1 in. diam by 1-114 in. high was thus produced. After canning in copper, these billets could be extruded (5: 1) on a 54-ton capacity, slow-traverse hydraulic press with the billet temperature at 1550°F and the extrusion die at 900°F. However, lack of densifica-tion of some of the extruded billets necessitated ratios of at least 23 :1. Ultimately, all billets were successfully extruded at 1500°F to 0.190 in. diam (32 :I), fully dense rods using a 200-ton capacity press and a ram speed of 90 ipm. The microstructures of as-extruded Zr-7 vol pct LazOS and Zr-7 vol pct Y2Os are shown in Fig. l(a) and (c), respectively. These structures are similar to all the as-extruded materials and consist of an elongated, single-phase zirconium matrix dispersed with oxide or carbide particles. Very little porosity is observed, and the interface between matrix and particles appears satisfactory. The size and distribution of particles, however, are not ideally of the type desired for dispersion strengthening. Since the primary study was of particle stability with respect to zirconium, no attempt was made to overcome agglomeration during powder blending and fabrication. Some areas exhibit fine, well-distributed particles; undoubtedly, a small proportion is submicroscopic and has the

Jan 1, 1963

By Edward Judd

CANADA&apos;S mining industry is rapidly recovering from the depression through which it passed in 1921. Its total output of $183,029,600 in 1922 was 6.4 per cent. greater than that of 1921, and was exceeded by only three previous years, 1917, 1918, and 1920. Table 1 compares the output of a few of &apos;the more important items selected from preliminary data published&apos; by the Dominion Bureau of Statistics. TABLE 1.-OUTPUT OF CERTAIN MINERAL PRODUCTS IN CANADA PER CENT. 1921 1922 CHANGE Cobalt, metal and in compounds, lb 252,000 443,800 +76.1; Copper contents of blister, matte, and exported ores, lb 47,620,820 43,321,400 - 9.0 Refined copper, lb 4,286,000 730,000 -83.0 Gold, fine oz 926,329 1,230,985 +32.8 Pig iron, sh. tons 665,676 429,024 -35.5 Lead, sh. tons 33,340 47,085 +41.2 Nickel contents of matte, etc., lb. 19,293,060 17,496,490 - 9.3 Silver, including that in base bullion, gold bullion, etc., fine, oz. 13,543,198 17,611,646 +30.0 Zinc (nearly all refined), sh. tons. 26,545 28,199 + 6.2 Asbestos shipments, sh. tons 92,761 136,657 +47.3 Coal, all grades, sh. tons 15,057,500 15,045,300 Gypsum shipments, sh. tons 386,550 441,160 +14.1 Natural gas, M. cu. ft 14,077,600 14,954,100 + 6.2 Petroleum, bbl : 187,540 178,570 - 4.8 Cement, bbl 5,752,885 6,943,968 +21.0 Brick, structural, all kinds, M. , , 109,009 127,137 +17.0 On the basis of estimated market values, the whole output of 1922 was contributed as follows: Metals, 33.4 per cent.; non-metallic minerals, 45.1 per cent.; structural materials and clay products, 21.5 percent.; this distribution indicates a return of the metal mining. industry nearly to the position of relative importance that it occupied. before 1921, in which year metals contributed only 28.7 per cent. to the total value. of output while non-metallics gave 51.1 per cent. Canadian cobalt originates entirely in the ores of the Cobalt district, which are mainly treated at smelters in southern Ontario, although some quantities of residues have been exported to England and Europe. Exports during 1922 increased even more than production, consisting of about four-fifths . cobalt oxides and salts, and one-fifth of cobalt alloys and other metal combinations.

Jan 8, 1923

By A. H. Daane, J. J. Hanak, F. H. Spedding

IN the study of the rare earths at the authors&apos; laboratory, methods have been devised for preparing pure rare earths and many of their properties&apos;- have been determined. Very little information is found in the literature on the properties of europium metal, which is the scarcest of the naturally occurring rare earths. Since we have recently prepared europium in appreciable quantities, we are in a position to describe the method of preparation and some of the properties of this metal. Metallic europium was first prepared by Klemm and Bommera who heated a mixture of potassium and EuC1, in vacuo, and obtained a mixture of europium metal and KC1. Trombe4 electrolyzed a molten salt bath containing NaC1, KC1 and EuC1, and collected the europium in a molten cadmium electrode as a cadmium alloy. The cadmium was subsequently removed by distillation but the properties of the residue indicate that pure europium was not obtained. McCoy attempted to prepare europium by distilling mercury from europium amalgam, but the stability of the Eu-Hg intermetallic compounds prevented a complete separation of the two elements. The preparation of very pure europium was suggested by previous work in this laboratory1,4 in which ytterbium and samarium were prepared by heating the respective sesquioxides with lanthanum metal turnings to 1450°C in vacuo and distilling ytterbium and samarium from the mixtures. Subsequently, small test experiments showed that europium also could be prepared by this method. A more detailed version of this method was used in the work described in this paper. Klemm and Bommer3 found by X-ray analysis that the metal had a body-centered cubic (bcc) structure with a lattice constant a, = 4.582 ± 0.00A (converted from kX units), with a bulk density of 5.30 g per cu cm. They found europium to be weakly ferromagnetic. Spedding, et al,7 found a,, to be 4.606 ± 0.001A. Barrett&apos; showed that the bcc structure persists throughout the temperature range 5 to 3000K with a, at 5, 78, and 300°K being 4.551 ± 0.003, 4.551 ± 0.004 and 4.577 ± 0.001A, respectively. Trombe1 described europium as being iron gray, malleable, about as hard as neodymium and not attacked by cold water. He estimated the melting point to be between 1100 and 1200°C. Previous work in this laboratory indicated that the pure metal corrodes rapidly in air and reacts with cold

Jan 1, 1959

By J. B. Cohen

In an investigation of the microstructure of shock-loaded metal specimens1 C. S. Smith found that there was little distortion of grain boundaries or change in external dimensions, although the hardness corresponded to that produced by severe rolling. Furthermore, the hardness of individual grains was independent of the deformation structures present; grains with no markings were as hard as those heavily populated with markings. These markings which resemble twins do not appear in copper until high shock-loads of the order of 200 kb are applied. It appears that due to the high velocity of a shock wave and its sharp front, heavy deformation takes place on a submicroscopic scale. In this work an attempt was made to examine this deformation, particularly at a load below which macroecopic markings appear. The broadening of 200 and 400 diffraction peaks was examined from the face of a poly crystalline sample normal to the direction of the shock wave. These peaks were chosen because the elastic constants in copper are such that residual strains would be greatest in the <100> directions; hence, the strain-broadening contribution to these peaks would be large in comparison to other sets. Also the broadening due to stacking faults and microtwins would be greatest with this set.2 A complete Fourier analysis of these peaks was made, as described by warren,&apos; using the Stokes correction with peaks from an annealed sample.3 With the aid of the U. S. Army Ordnance Corps EDVAC computer and a curve matching program, sixty sine and sixty cosine coefficients were obtained for each peak. The last of these was about 1.5 pct or less of the largest coefficient, indicating good representation. Transverse sections from a 1.5 in. rod of as-drawn electrolytic tough-pitch copper were reduced in cross-sectional area about 50 pct by cross rolling. Disks 1.5 in. in diam were recrystallized at 275 °C for 30 min and then at 300°C for the same time. The faces were polished and deeply etched in nitric acid to remove 25 mils. The grain size was 0.02 mm. Laue back-reflection patterns indicated the sample was well recrystallized. The two diffraction peaks from this sample were recorded on a Norelco diffractometer using filtered copper radiation. Peak intensities were kept less than 600 cps to assure linearity of the counter and circuitry. This sample was then placed between two rods of the same material and diameter. The top rod was 2.25 in. long and the bottom rod 1 in. long. (In

Jan 1, 1961

By C. A. Stetefeldt

IK the dry-crushing of ores, either by stamps, rolls, or other machinery, it is essential that the material should be free from moisture. Hence a contrivance which effects this with economy, and is of durable and compact construction, is a great desideratum. It is claimed for the below-described shelf dry-kiln, that it possesses these qualifications in a high degree. The construction of the shelf dry-kiln is based on the Hasenclever principle. That is to say, a number of inclined shelves are arranged zig-zag above each other in a vertical shaft, having openings or slits where they meet, on which the ore rests in a stratum, the thickness of which is governed by the width of the slits and the inclination of the shelves. If a portion of the charge is removed at the end of the bottom shelf, a sliding motion of the ore takes place on all shelves above, and the top shelf is replenished from a hopper set over it. It will be seen that the shaft is divided by the shelves into a number of triangular prismatic spaces. Through these the hot gases from a fireplace are made to circulate, each space communicating with the next one by a flue arranged in the sidewall of the shaft. These flues being located on alternate sides of the shaft, a continuous passage is formed through the whole structure. After thus stating the principle of the construction, its details will be easily understood by reference to the drawings, Fig. 1 to Fig. 5. The drawings, Fig. 1 to Fig. 4, represent two kilns united into one structure. The cast iron shelves(a) are 2 feet 4 inches wide and 5 feet long, with sides and a back 4 inches high, and are cast a full halfinch thick. How they rest on the brackets(d), and interlock each other, is shown in Fig. 5. Three such shelves, with an inclination of 38&apos;) are placed in one row in a brick shaft 7 feet 1/2 inch wide and 4 feet deep. The ore hoppers(g) rest on the iron bems(f). At the end of the bottom shelves are the discharge-doors(b), with shoots projecting beyond the front wall. A swinging apron(e) keeps the ore in place. By dropping it a car below the shoot is filled with dry ore. A number of extra-large pieces of ore may cause a stoppage in the slits ; for such an emergency the openings(e) are provided, through

Jan 1, 1884