Search Documents

By J. E. Papin

MORENCI ores contain as an average about 0.015 pct molybdenite, MoS2. Incidental to the concentrating operations applied for the recovery of copper minerals, approximately two-thirds of the molybdenite is floated and appears in the final copper concentrate. The economic importance of molybdenum and the success achieved in its recovery in milling operations elsewhere encouraged research directed toward its recovery in marketable form. Several procedures are utilized to effect separation of molybdenite from copper and iron sulphides, but only two have wide application. In the better known of these two methods the molybdenite in the copper concentrate is depressed in a flotation operation using soluble starch as the depressant. The tailing from this treatment thus becomes a low-grade molybdenite concentrate which after thickening, filtering, and low temperature roasting is repulped with water and subjected to additional flotation steps for recovery of the molybdenite. A thio-phos-phate collecting agent is employed in flotation of the copper minerals. Presumably the stability and lasting effects of that collector type necessitated the practice of depressing molybdenite followed by subsequent roasting to insure elimination of copper and iron sulphides from final molybdenite concentrate. The second important method of recovery is applied at various southwestern plants. In those plants xanthates are in use as copper collecting agents. It has been found that xanthates are relatively unstable and their collecting power for sulphides is destroyed by very simple procedures. The method generally applied is to subject the xanthate-acti-vated concentrate, in the form of a pulp, to prolonged heating using steam as the heating medium. A concentrate thus treated may then be subjected to a flotation operation for recovery of the molybdenite, using mineral oil collecting agents, and the copper and iron sulphides will be depressed. Neither of the above processes was applicable to Morenci concentrates. Morenci uses a thio-phos-phate collecting agent in its flotation operation. However, it was established that soluble starch was not a depressant for Morenci molybdenite; therefore the first step in that process was not applicable. AS would be expected the copper and iron sulphides in Morenci concentrates could not be depressed by the heating methods used on xanthate activated concentrates. Low-temperature roasting did eliminate the effects of the thio-phosphate but had to be rejected as uneconomic in as much as the tonnage of concentrates involved was too great. Preliminary research having established the above facts, it became obvious that new methods would have to be developed for the recovery of molybdenite from Morenci concentrates. A broad laboratory investigation was initiated along two general lines, both directed toward depression of copper and iron sulphides. One approach was through the use of water-soluble oxidizing agents with the objective of destroying the thio-phosphate in the concentrate and thus eliminating its collector effect. The other approach involved the use of soluble sulphides, which have long been recognized as sulphide depressants. These efforts resulted in laboratory processes which showed promise. Research was then extended to a pilot plant having a daily capacity of several tons of concentrate. This operation soon demonstrated that soluble sulphide—basically sodium polysulphide—when applied to a pulp made slightly acid with sulphuric acid, proved to be the most effective sulphide depressant. The rate of concentrate treatment in this plant and the low molybdenite content of the concentrate prevented carrying the process to a conclusion, namely, production of molybdenite concentrate of marketable grade. Laboratory treatment of pilot plant concentrate indicated that a marketable product could be made from it, given a tonnage suited to available cleaner flotation machine capacity. Accordingly, the molybdenite plant was enlarged to permit treatment of the total copper concentrate from the extension plant, maximum of approximately 800 tons per day. In the enlarged plant a major difficulty was encountered. No criteria could be established as a basis for control of the process. In the early stages of flotation, because of the small amount of molybdenite involved, there was no visual evidence of the relative floatability of molybdenite with respect to

Jan 1, 1956

By T. M. Morris

A SEARCH of the literature reveals that no measurements have been made of the forces acting between a small solid particle whose surface is hydrophobic, and an air bubble to which the solid adheres, both immersed in water. Analyses have been made of the forces acting to support a greased solid on the surface of water, and the forces acting to cause a solid, whose surface is hydrophobic, to adhere to an air bubble in water. The latter analysis T. M. MORRIS, Junior Member AIME, is in the Department of Metallurgical Engineering and Mineral Dressing, School of Mines and Metallurgy, Rolla, Mo. New York Meeting, February 1950. TP 2734 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 16, 1949. This paper is the result of work done for part of a doctor's thesis at the Missouri School of Mines and Metallurgy. is often incomplete, however, because the internal pressure of the bubble has been neglected. It will be demonstrated that the internal gas pressure is not a negligible factor when dealing with bubbles of the size encountered in flotation. A study of the forces acting between an air bubble attached to a large flat surface is informative. It must be borne in mind, however, that this is not the condition present in a flotation cell, where the particle is small compared to the size of the bubble. The bubble is allowed to spread to its maximum contact angle on a large flat surface in the first case, whereas in the second case, the spread of the bubble is limited to the surface of the small particle which is presented to the bubble. Kabanov and Frumkinl studied the forces acting to cause adhesion of bubbles of hydrogen to a large surface of mercury, which served as an electrode in a dilute sulphuric acid solution. The force acting to hold the bubble to the mercury surface was found to be the vertical component of the surface tension between hydrogen and the sulphuric acid solution. The forces tending to cause the bubble to separate from the mercury surface were found to be: (1) the force exerted due to the internal pressure of the bubble acting upon the area of contact between the bubble and the mercury surface, and (2) the buoyant force of the bubble minus the hydrostatic force acting at the base of the bubble. These investigators photographed bubbles that were just on the verge of separating from the mercury surface. From these photographs, they measured the contact angle between the mercury surface and the tangent to the hydrogen-solution interface at the point of contact between bubble and mercury surface. They calculated the volume of the bubble and the internal pressure of the bubble. The equivalence between the upward acting and downward acting forces was remarkable. Wark2 pursued an investigation similar to that of Kabanov and Frumkin, and at the same time. His deductions verified those of Kabanov and Frumkin. He also considered the conditions present in flotation and was aware of the effect of the internal pressure of the bubble. Further, he proposed several conditions under which a small solid particle would adhere to an air bubble in water. In 1922, Edser," an English physicist, made the following statement. "It must be remembered that no particle could float stably, but for the possibility of variation of the contact angle, for if this were a constant, a slight tilt would inevitably cause the particle to sink." Wark criticized this statement, maintaining that the contact angle does not vary. The experimental data to be presented indicates that Edser was correct. Experimental Procedure: Briefly, the experimental procedure was as follows. A bubble of air was generated in distilled water. A rod of known diameter, one end of which was water repellent, was attached to this bubble. The weight of the 'rod was measured. The internal pressure of the bubble was measured with a manometer. The hydrostatic head from the surface of the water to the bottom of the rod was measured. The angle between the horizontal projection of the end of the rod and the tangent to the bubble at the circle of contact be-

Jan 1, 1951

By T. M. Morris

A SEARCH of the literature reveals that no measurements have been made of the forces acting between a small solid particle whose surface is hydrophobic, and an air bubble to which the solid adheres, both immersed in water. Analyses have been made of the forces acting to support a greased solid on the surface of water, and the forces acting to cause a solid, whose surface is hydrophobic, to adhere to an air bubble in water. The latter analysis T. M. MORRIS, Junior Member AIME, is in the Department of Metallurgical Engineering and Mineral Dressing, School of Mines and Metallurgy, Rolla, Mo. New York Meeting, February 1950. TP 2734 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 16, 1949. This paper is the result of work done for part of a doctor's thesis at the Missouri School of Mines and Metallurgy. is often incomplete, however, because the internal pressure of the bubble has been neglected. It will be demonstrated that the internal gas pressure is not a negligible factor when dealing with bubbles of the size encountered in flotation. A study of the forces acting between an air bubble attached to a large flat surface is informative. It must be borne in mind, however, that this is not the condition present in a flotation cell, where the particle is small compared to the size of the bubble. The bubble is allowed to spread to its maximum contact angle on a large flat surface in the first case, whereas in the second case, the spread of the bubble is limited to the surface of the small particle which is presented to the bubble. Kabanov and Frumkinl studied the forces acting to cause adhesion of bubbles of hydrogen to a large surface of mercury, which served as an electrode in a dilute sulphuric acid solution. The force acting to hold the bubble to the mercury surface was found to be the vertical component of the surface tension between hydrogen and the sulphuric acid solution. The forces tending to cause the bubble to separate from the mercury surface were found to be: (1) the force exerted due to the internal pressure of the bubble acting upon the area of contact between the bubble and the mercury surface, and (2) the buoyant force of the bubble minus the hydrostatic force acting at the base of the bubble. These investigators photographed bubbles that were just on the verge of separating from the mercury surface. From these photographs, they measured the contact angle between the mercury surface and the tangent to the hydrogen-solution interface at the point of contact between bubble and mercury surface. They calculated the volume of the bubble and the internal pressure of the bubble. The equivalence between the upward acting and downward acting forces was remarkable. Wark2 pursued an investigation similar to that of Kabanov and Frumkin, and at the same time. His deductions verified those of Kabanov and Frumkin. He also considered the conditions present in flotation and was aware of the effect of the internal pressure of the bubble. Further, he proposed several conditions under which a small solid particle would adhere to an air bubble in water. In 1922, Edser," an English physicist, made the following statement. "It must be remembered that no particle could float stably, but for the possibility of variation of the contact angle, for if this were a constant, a slight tilt would inevitably cause the particle to sink." Wark criticized this statement, maintaining that the contact angle does not vary. The experimental data to be presented indicates that Edser was correct. Experimental Procedure: Briefly, the experimental procedure was as follows. A bubble of air was generated in distilled water. A rod of known diameter, one end of which was water repellent, was attached to this bubble. The weight of the 'rod was measured. The internal pressure of the bubble was measured with a manometer. The hydrostatic head from the surface of the water to the bottom of the rod was measured. The angle between the horizontal projection of the end of the rod and the tangent to the bubble at the circle of contact be-

Jan 1, 1951

By O. R. Wagner, R. O. Leach, H. W. Wood, C. F. Harpke

PAN AMERICAN PETROLEUM CORP.TULSA, OKLA. CASPER, WYO A field test has been made in which additional oil recovery was obtained from a previously-waterflooded "oil-wet" sandstone reservoir. This recovery improvement was accomplished by adjusting the reservoir wettability through chemical treatment of the flood water. The test was made in the Muddy sand of the West Harrisburg Unit, Neb. The chemical used, sodium hydroxide, was injected as a slug of dilute caustic solution through a water-injection well. The natural wettability of the reservoir and the chemical requirements for reversing wettability were determined in the laboratory from contact-angle studies using field water and oil samples. Laboratory flood tests with a synthetic system had shown that reversing the wettability of an oil-wet consolidated core would lead to improved oil recovery. The field performance indicates that the mechanism by which increased oil retovery is obtained in the field is the same as that observed in the lahoratory. Laboratory studies indicate that higher ultimate recoveries and decreascd water-injection requirements result when the adjusting agent is added early in the life of the flood. However, a previously waterflooded area was intentiorzally chosen for the field test so that unambiguous conclusions could be made about the effects of chemical injection on wettability and the extent of oil-recovery improvernent afforded by wettability reversal. Forces existing at the fluid-solid and fluid-fluid interfaces in a porous medium have an important effect on oil recovery during a water flood. Modifying these interfacial forces in the reservoir to improve oil recovery has been the object of much research. Several papers' ' have discussed the use of surfactants to lower the water-oil interfacial tension. This paper describes work concerned with improving oil recovery by modifying the forces at the fluid-solid interfaces— that is, by changing the preferential wettability. An earlier paper: presented evidence to show that some reservoir systems could be changed from preferentially oil-wet to preferentially water-wet by the action of simple chemicals added to the water to increase waterflood oil recovery. The process was attractive for further study because it used only inexpensive chemicals and because it called for a gross "wettability reversal" rather than for a precise adjustment. The present paper is an extension of the earlier work. Laboratory flow tests were made using treated water and oil in a consolidated core to determine the amount of additional oil recovery and the producing performance which might be expected from reversing the wettability of an oil-wet reservoir during a flood. A contact-anglc study using water and oil from the Muddy "J" sand of the Harrisburg field, Banner County, Neb., indicated the reservoir to be preferentially oil-wet and susceptible to wettability reversal through chemical injection. Based on these studies, a field trial of wettability-reversal water flooding was initiated. in the Harrisburg field. The primary purpose of the trial was to determine if wettability-reversal flooding would improve oil recovery in an actual field situation. The field trial was also an important test of the laboratory tecnique used to determine the effect on oil recovery of certain wettability manipulation, as well as a test of the contract-angle method of determining reservoir wetra-bility. The paper is presented in two parts. The first part covers the laboratory experiments leading up to the field trial, and the second part covers the field trial. PART I—LABORATORY STUDY The laboratory experiments consisted of displacement tests using an idealized fluid system and of a contact-angle study with crude and water from the Muddy "J" sand of the West Harrisburg Unit, Banner County, Neb. The displacement tests were designed to determine the effects of a particular wettability manipulation, oil-wet to water-wet, on oil displacement in a water flood. The contact-angle measurements were made to determine the natural wettability of the reservoir and to determine if beneficial wetting changes could be brought about by a chemical addition to the flood water. PROCEDURE DISPLACEMENT TESTS The displacement tests were perfornled in a consolidated sandstone core using a refined oil and water. The wetting properties of this system could

By Philip E. LaMoreaux

Fluoride, generally less than 0.5 ppm, is present in ground water from rocks of Paleozoic age and older, in northern and eastern Alabama. Some of the water-bearing formations in the Coastal Plain area of the State yield water with as much as 6.8 ppm fluoride.

Jan 1, 1950

[Officers and Committees of the Society of Petroleum Engineers 1 Officers and Staff of the AIME 2 . Officers of AIME Sections Predominantly Petroleum in Membership 3 AIME Local Sections and SPE Regional Organization Maps 5 Alphabetical List of Members 7 Geographical List of Members 102 Advertisers' Index 133]

Jan 1, 1961

By Robert Glass Cleland

[CAPITAL EXPENDITURES TWENTY YEARS, 1934-1950 Morenci Branch $ 67,261,000 New Cornelia Branch 24,677,000 Copper Queen Branch 7,766,000 United Verde Branch 11,037,000 Miscellaneous Total Mining Division Refining Division 5,584,000 Fabricating Division 17,032,000 Total Capital Expenditures $135,823300]

Jan 1, 1952

By Philip E. LaMoreaux

Fluoride, generally less than 0.5 ppm, is present in ground water from rocks of Paleozoic age and older, in northern and eastern Alabama. Some of the water-bearing formations in the Coastal Plain area of the State yield water with as much as 6.8 ppm fluoride.

Jan 8, 1950

By D. L. H. Forbes

(New York Meeting, February, 1912.) Introduction.. THE application of the cyanide process to complex sulphide ores for the extraction of their bold and silver is no longer a novelty, but, as an example showing modern tendencies in this direction, the following description of the new milling process at the Lucky-Tiger mine is offered: The extraordinary richness of the ore in the upper workings of this mine made any thought of milling in its early hays seen unnecessary. Its location in an almost inaccessible part of the rugged mountains just south of the Arizona boundary-line, and 60 miles from the town of Douglas, made the expense of bringing in machinery and supplies a very serious consideration. But, after the property had been shipping high-grade ore on mule-back for a few years, there remained in the mine a considerable tonnage of vein-matter that was too low in value to ship, but which it was thought could be milled near the mine at a profit. The first milling-experiment consisted in the installation of Nissen stamps in conjunction with concentrating-tables and Frue vanners, but, as the ore from the upper workings contained most of its silver in the form of cerargyrite, this type of mill was not successful. The proximity of the mine to the great copper-concentrating mills of Cananea and Moctezuma naturally made the influence of copper-milling, ideas felt in the company's next installation. At considerable expense a stage-crushing concentrating-mill, with a capacity of 100 tons per day, was built. This mill was modeled along the lines of the most approved practice in copper-concentrators at that time, the main idea being that crushing by stages in rolls was necessary in order to prevent losses from ?sliming." Largely owing to the fact that, when the mill

Aug 1, 1912

By K. I. Savage, L. G. Austin, S. C. Sun

The comminution environment - the physical, chemical, and solid state - was studied for silicon carbide ground wet in a laboratory vibratory mill. The relative importance of these variables on the grinding rate of producing a material 50% passing 5µ from a powder feed of 50% passing 19µ was established.

Jan 1, 1975

By John Freeman

THE tensile properties of steels at elevated temperatures have been studied by numerous investigators,1 primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20° to 500° C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon of increased tensile strength and decreased ductility in the so-called "blue-heat" range, approximately 200° to 300° C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930

By T. E. Eagan, W. R. McCrackin

IN dealing with segregation in babbitt, and its effect on the final cast structure, which is a bearing, it is obviously impossible to cover all of the compositions manufactured. Each composition, of course, will exhibit certain specific types of segregation. However, as examples,, two compositions of babbitt are presented: one a tin-base of well-known analysis and the other a lead-base, which in the past few years has found wide usage. Bearings usually are cast either statically or centrifugally; therefore the effect of these two methods on segregation is presented. EXPERIMENTAL PROCEDURE A slab of babbitt 1/2 in. thick by 5 in. wide and 17 in. long was cast, using a book mold with the long edge vertical. An A.S.T.M. grade 2 babbitt was used (3.5 per cent copper, 7.5 per cent antimony, remainder tin), to which 0.10 per cent tellurium had been added. Unfortunately, no metal without tellurium was available. The mold to hold the babbitt was heated to approximately 300°F., the temperature being judged by the babbitter. The pouring temperature of the babbitt was 875°F. (470°C.). One slab was made by allowing the babbitt to cool without stirring. The other slab was stirred during the entire cooling cycle. This stirring consisted of a vigorous churning or puddling into the mold until complete solidification had taken place. Three samples were removed from these slabs. One was taken at the extreme bottom, another half way to the top, and another at the extreme top, all at the center of the width. Chemical, macroscopic and microscopic examination was made of all samples. Table I shows the chemical analyses obtained at the described positions [ ] in the slab. The analyses show no serious amount of gravity segregation. Microscopic examination from edge to edge of the slab showed little change in structure. From top to bottom there was a progressive coarsening of the grain size in the stirred slab but little change in the slab that was not stirred (Fig. I). No definite exhibit of segregation could be detected. In line with our experimental study on the tin-base babbitts, we cast an almost duplicate slab using A.S.T.M. Alloy No. 15, containing 0.9 to 1.25 per cent tin, 14.75 to 15.5. per cent antimony, 0.80 to 1.25 per cent arsenic and 0.4 per cent copper. The slab was 16 in. long and 3/8 in. thick, cast with the long side vertical. One slab was allowed to cool normally and the other was stirred continually during cooling. The pouring temperature of the babbitt was

Jan 1, 1944

By T. E. Leontis, J. P. Murphy

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By J. P. Murphy, T. E. Leontis

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By C. G. Dunn

MANY investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal orientation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the, complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.1-3 Furthermore, it is believe that high-stress regions exist in the vicinity of these bands4a and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallization.5,6 Similar evidence has been published for nonferrous metals.5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins existed prior to recrystallization.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary orientation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha irons Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing. three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involve more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By A. H. Daane, B. J. Beaudry

The Sc-Ti system was studied by thermal, metal-lographic, and X-ray methods. Scandium was found to transform at 1334 °C from a (hexagonal) to ß which was concluded to be bee since a continuous series of solid solutions is formed between ß scandium and ß titanium at elevated temperatures. There is a minimum in the solidus at 51 wt pet Ti and 1300°C, a monotectoid at 1050°C and 49 wt pet Ti, and a eutectoid at 875°C and 91.5 wt pet Ti. The maximum solubility of titanium in a scandium is 13.5 wt pet at the monotectoid temperature, while the maximum solubility of scandium in a titanium is 6.5 wt pet at 875°C. SCANDIUM, a member of Group 111 A of the periodic table, and now called a rare-earth metal,' has become of interest recently due to its low density (2.99 g per cc) and relatively high melting point (1539°C).Spedding,' et al. have described a method of preparation of pure scandium metal and have made a study of its basic properties. Since scandium is approximately 10 to 12 pet smaller in at. diam than the other rare earths while its electronegativity and valence are the same, a knowledge of its alloying behavior in contrast to these elements should be very helpful to fundamental alloy theory. Since scandium is quite scarce and difficult to prepare in pure form, its use as a structural material by itself seems quite unlikely. However, its use in special cases as an alloying addi- tive to other low-density materials is a possible application; the Sc-Ti system was chosen for this reason and for others of fundamental interest. Scandium was suspected of having a high temperature bee form as do some of the other rare-earth metals.3'4 Since titanium has a high-temperature bee form, a continuous series of solid solutions at elevated temperatures between ß scandium and ß titanium would prove the existence and structure of the high-temperature form of scandium. The existence of a continuous series of hexagonal solid solutions at room temperature was predicted by Burkhanov and Savitskiy,5 but Hias shown to be incorrect in early X-ray studies. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar titanium and distilled scandium prepared by the method described by Spedding,2 et al. The major impurities are listed in Table I in PPm. Alloy Preparation. All the alloys examined were initially formed in a nonconsumable electrode are-melting furnace under an atmosphere of purified helium or argon. A curve based on the observed weight loss of 0.6 pet* when titanium was melted

Jan 1, 1962

By W. R. Hibbard

Although extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110) , [111] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampton5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr in a standard mer-curous nitrate test. Edmunds12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wasserman11 reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. Preparation OF Specimens Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5, 10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. Determination of Pole Figures A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pet nitric acid to 0.0015 in. thickness and (111) pole figures were determined using copper K-alpha radiation in the manner described by Brick.' The three general types of pole figures

Jan 1, 1949

By W. R. Hibbard

Although extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110) , [111] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampton5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr in a standard mer-curous nitrate test. Edmunds12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wasserman11 reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. Preparation OF Specimens Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5, 10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. Determination of Pole Figures A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pet nitric acid to 0.0015 in. thickness and (111) pole figures were determined using copper K-alpha radiation in the manner described by Brick.' The three general types of pole figures

Jan 1, 1949

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen' indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink' has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.' Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952

By Walter R. Hibbard

ALTHOUGH extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110), [III] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampon5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr s in a standard mercurous nitrate test. Edmunds 12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wassermann reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. PREPARATION OF SPECIMENS Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5,10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. DETERMINATION OF POLE FIGURES A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pct nitric acid to 0.0015 in. thickness and (III) pole figures were determined using copper K-alpha radiation in the manner described by Brick.1 The three general types of pole figures

Jan 1, 1947