Search Documents

By J. C. McDonald

A DDITIONAL experimental data are presented in this note on a phenomenon which has been touched on but lightly in the literature. The common magnesium base rolling alloy (AZ31B) contains about 3 pet A1 and 1 pet Zn. When cold rolled, it hardens until it starts to break up in the rolls at 30 to 50 pet reduction. When it is heated after rolling to full hardness, it softens. However, other magnesium alloys have shown themselves capable of being cold rolled indefinitely, provided the ratio of roll diameter to starting gage is sufficiently high. As measured by the tensile test, these alloys actually soften when the reduction becomes large (60 to 90 pct). A subsequent heating at 300' to 500°F can produce hardening of this metal. Heating at higher temperatures (600' to 800°F) causes recrystalliza-tion and softening. Menzen' has shown that a magnesium base alloy can be cold rolled without intermediate anneals as much as 90 pet. The alloy studied, Mg-1.5 pet Mn, softened considerably between 20 and 90 pet reduction, as measured by tensile properties; a decrease in yield strength of 30 pet, and an increase in elongation from 3.2 to 16.7 pet (longitudinal direction of the sheet). However, Menzen gives no data on the reaction of this metal. to heating. Ansel and Betterton2 and Hurst and Hatch3 report a similar effect in Mg-1.5 pet Mn-0.1 pet Ca. Their data show an initial hardening, followed by softening. The former authors also show that the alloy softened by cold rolling will harden when heated at low temperatures, and that these effects are absent in Mg-3 pet Al-1 pet Zn. In the course of work4, 5 some years ago, the author observed similar effects with alloys containing cerium, thorium, or zirconium; but not with elements like aluminum, silver, or zinc. Table IA contains the results of an experiment which shows these effects rather well. A binary alloy with 0.3 pet total rare earths (Mischmetal* added) was rolled hot to 1/16 in. and then annealed to full softness by heating 30 min at 800°F. Rolling was continued at 1.5 pet per pass to 80 pet total reduction on 8 in. diam rolls. The metal was harder after 20 pet work than initially but, at 80 pet reduction, properties were back to their original values. Heating for 1 hr at 450°F produced about the same hardness whether the reduction was 20 or 80 pet. At intermediate reductions, the metal hardened, but not to as high values. Extensive cold rolling may also be carried out on metal hot rolled at temperatures sufficiently low to produce a semihard temper. Mg-0.6 pet Zr was rolled to 0.1 in. at 700° to 800°F, 30 pet per pass. As shown in Table IB, a further cold reduction of 85 pet, at 1.5 pet per pass, definitely softened the metal.

Jan 1, 1959

By Takeyasu Ito, Mayumi Someno, Kazuhiro Goto

SINCE the pioneering work by Kiukkola and Wagner,1 many experiments have been reported on solid electrochemistry at elevated temperatures. However, the studies have been confined to experiments under isothermal conditions. One may conceive many situations under nonisothermal conditions. With two different temperatures T1, and T2 at the two electrodes, the electromotive force, E of a Galvanic cell will be expressed by the following equation under a steady state heat transfer in solid electrolytes of zirconia-lime and thoria-lime. E = ^ $ l&-dGO2+a(T2-Ti) [1] where tO2- is the transference number of oxygen ions in the electrolyte, Go, is the chemical potential of oxygen, and a is the coefficient of the thermoelec-tromotive force due to the temperature difference. The objective of the present study was to evaluate the coefficient of the thermoelectromotive force for zirconia-lime and thoria-lime under isobaric condition. The physical meaning of this coefficient is out of the scope of the present communication. The experimental cell assembly is schematically shown in Fig. 1. The zirconia-lime electrolyte tube and thoria-lime electrolyte tube were 8.0 mm OD and 5.0 ID, from commercial sources with chemical analyses of 94.8 wt pct ZrO2, 3.85 pct CaO, 0.83 pct SiO2, 0.25 pct TiO2, and 0.05 pct Fe2O3; and 95.0 pct ThO2, 4.0 pct CaO and rare earth metal oxides, respectively. The specific gravity was 5.5 g per cu cm for zirconia-lime and 9.8 g per cu cm for thoria-lime. Original powder size before shaping and sintering the tube was several microns for both electrolytes. The distance separating the two electrodes was 4.0 or 5.0 cm. Platinum wire of 0.5 mm diam was used for the electrodes. The temperature gradient was controlled by heating one electrode with a small heating coil of nichrome wire. The temperatures at the two electrodes were measured with two calibrated Pt-13 pct Rh:Pt thermocouples, directly contacting the two platinum electrodes. The atmosphere was either air or pure oxygen. The partial pressure of oxygen in air was considered equal at the vicinities of the two electrodes, with negligibly small thermal segregation in the gas phase. The difference of the chemical potential of oxygen was controlled only by the temperature difference at the two electrodes and not by the oxygen pressure difference. The temperature ranges were 600" to 1200°C for zirconia-lime and 850" to 1200°C for thoria-lime electrolytes. Fig. 2 shows the relation of the measured electromotive force and the difference of the oxygen chemical potential at the two electrodes for zirconia-lime and thoria-lime electrolytes. The electromotive forces in the figure were measured by a *0.05 mv potentiometer. The chemical potential difference was calculated by the following equations.'

Jan 1, 1970

By F. T. Havard

(Canal Zone meeting, November, 1910.) I. INTRODUCTION. THE present truce in litigation between Western smelting and ranching interests gives opportunity for a summary of the results achieved by metallurgists in condensing fume and de-acidifying furnace-gases. In the absence of complete records of past experiments, there has been a good deal of unnecessary duplication of attempts and' failures. Yet, especially under the recent policy of our large corporations, looking to the economic recovery of the values of by- and waste products, original and, in some cases, effective measures have been developed by American metallurgists. In the case of Bliss vs. the Anaconda Copper Mining Co., the Montana Supreme Court, recognizing the progressive efforts made to render the flue-gases innocuous, and the value to the community of the smelting company's operations, refused to hamper its work, and returned a verdict in favor of the defendant. In the trial, the experimental firms of the company in the so-called "affected region" were proved to be thriving perfectly, showing that immunity was guaranteed to vegetation and stock by the wide distribution of the sulphurous acid gas in the dry air of Montana. Indeed, L. S. Austin has proved that by the time the fume is 4,000 ft.. distant from the stack, the percentage of sulphurous acid has been diminished from 2.28 to 0.00045; and Angus Smith has shown that rain must contain 40 parts per million of free acid before vegetation is affected. The arsenic in the stack-gases is but a very small part of the original content of the ore, of which 80 per cent. and over is rejected in the concentrator and furnace waste-products or recovered in the flues. Nevertheless, neither the peace in Montana nor the armistice

Aug 1, 1910

By Albert Sauveur

IT is not without some hesitation, and even misgiving, that I venture into a discussion of the now classical Roberts-Austen Roozeboom diagram, lest I too fail, like so many other writers, in giving a satisfactory and logical explanation of these interesting curves. Roozeboom's original diagram is reproduced in Fig. 1. The generally accepted meaning of the various curves has been so often described before this Institute that it will suffice to recall it briefly before passing to my own interpretation of the changes involved.

Nov 1, 1906

By AIME AIME

The following abstract of the minutes of the final Adjourned Annual Business Meeting, held Nov. 12, 1912, in the office of the Institute, 29 West 39th Street, New York City, is here presented for the information of the membership at large. On the announcement by the Secretary that there was a quorum present, President James F. Kemp called the meeting to order. The minutes of the Adjourned Annual Business Meeting of Oct. 7, 1912, were read and approved. (Sec p. xi,Bulletin No. 71, November). Prof. Jos. W. Richards, in behalf of the Special Committee of the Board of Directors and the Council (Messrs. Richards, Kirchhoff, and Rand), withdrew the two proposed amendments to the Constitution offered by the said Committee at the Adjourned Annual Business Meeting of Oct. 7, 1912. (See Bulletin. No. 70, October, 1912, p. vi., and Circular Announcement No. 8, Oct. 15, 1912, p. 15.) Professor Richards presented a syllabus of the proposed amendments to the Constitution and By-Laws prepared by the Special Committee. Several members present discussed various sections of the proposed Constitution, and the Committee advised that the suggestions would he duly considered before submitting the final document, which would be duly presented and sent to the membership at large at least 30 days before the next Annual Business Meeting, Feb. 18, 1913. Professor Richards presented a resolution, seconded by Mr. Kirchhoff, making a change in the present Certificate of Incorporation, so that it would conform to the proposed changes in the Constitution and By-Laws; said resolution was unanimously adopted. Professor Richards presented another amendment to the Constitution, which had been purposely omitted from the printed list, but had been requested by many members, namely, the creation of a " Class of Fellows." This question was freely discussed at the Cleveland meeting (see Bulletin No. 71, November, 1912, p. 1348), and in view of the diversity of opinion it was-decided to present it in separate form for separate action of the membership at large at the Annual Business Meeting, Feb. 18, 1913. In answer to question, the President announced that the proposed amendments to the Constitution and By-Laws presented by Messrs. Corning and Stone at the Adjourned Annual Business Meeting, Oct. 7, 1912, and published in Circular Announcement No. 8, Oct. 15, 1912, were still on record. Professor Richards presented a syllabus of the proposed amendments to the By-Laws, and several sections were discused by members present, but no action of record was taken. Mr. Charles F. Rand read a letter from Mr. L. K. Armstrong, Sec-retary of the Spokane Local Section of the Institute, referring to the proposed amendments to the Constitution, and he announced that many of Mr. Armstrong's suggestions were, in one form or another, already incorporated in the proposed amendments submitted by the Special Committee. A special vote of thanks was passed to Dr. Albert R. Ledoux for the valuable assistance rendered by him to the Special Committee in the preparation of the proposed amendments to the Constitution and By-Laws.

Dec 1, 1912

The Institute has no available copies of Bulletin No. 7, January, 1906, and Bulletin No. 105, September, 191.5. The sum of 30.50 per copy will be paid for these Bulletins.

Jan 6, 1917

By Ellsworth Daggett

In the first paper on the Russell process presented by Mr. Stetefeldt, in May, 1884 (Transactions, xiii.), the process was treated from a purely theoretical standpoint.. 111 his second paper of October, 1886 (Transactions, xv,), the details of the plant, the chemicals used, and the manipulation in both mill and laboratory were treated. The aim of the present paper is to present economical results recently attained, new data affecting the preparation and manipulation of ore in the mill, and a more complete and systematic scheme of laboratory work. This paper is compiled mainly from Mr. Russell's notes of his own experience. Many of these notes, particularly those relating to work at Cusihuiriachic,* Mexico, have been upon work directly under the personal observation of the compiler, who takes pleasure in thus presenting to the Institute, data and considerations of much interest and value pot only to users of the Russell process, but to mill men generally. The description of the chemicals used and of the preparation of the mill-solutions being' in part the same now as when Mr. Stetefeldt's second paper was published, some use is here made of portions of that paper. No theoretical matter is here given. For a treatise containing also the theory of the process the reader is referred to Mr. Stetefeldt's complete work on " Lixiviation of Silver Ores by Hyposulphite Solutions," now in preparation. To facilitate the consultation of this paper, the following synopsis and index is prefixed. The figures in parenthesis indicate the page of this paper on which the subject is treated.

Jan 1, 1888

By J. B. Morrow

BITUMINOUS COAL production for 1937 up to Nov. 27, was 400,000,000 ions, an increase of 3.43 per cent over the comparative period in 1936. The in- crease in consumption, however, was not so great as the increase in production. Stocks of coal, mostly in the hands of consumers, on Nov. 1 were 57,000,000 tons, compared to 44,400,000 tons at the same periods in 1936. The prospects were that both production and consumption for December, 1937, would be lower than for the corresponding month of 1936. , Anthracite production for the period ending Nov. 20 was 43,900,000 tons, com- pared to 48,500,000 tons for the corresponding period in 1936, or a decrease of 9.5 per cent. Production of mechanically loaded coal in. 1936 was approximately 57,000,000 tons, an increase of 17.5 per cent over

Jan 1, 1938

By E. J. Wasp, N. T. Cowper, R. A. Davis, W. F. McDermott

On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this $5 million installation climaxed three years of development, testing, and construction. The mine and concentrator are located approximately 30 miles from the town of Waratah in a rugged semi-mountainous terrain. The open pit mine will produce approximately 5 million long tons a year of crude ore, which is ground in autogenous mills, separated magnetically, thickened and prepared for the pipeline. The 53-mile pipeline transports the 2,250,000 tons of concentrate north to Port Latta. The Port Latta facilities include the receiving, storage and thickening equipment for the slurry as well as filtering, balling and pelletizing equipment to produce the 2,250,000 tons of high grade iron ore pellets. Five vertical shaft furnaces are used for pelletizing.

Jan 1, 1969

By A. T. Yu

As the first loads of Noamundi iron ore rumbled into the new 54-in. Gyratory Crusher on March 30, 1968, one of India's largest and most modern iron ore processing complexes began operations. The completion of the $13 million mining and processing complex brought to a successful conclusion the second chapter of a phased expansion program initiated in 1958 by India's gigantic Tata Iron and Steel Co. The completed complex will yield annually 2.5 million tons of washed, sized ore and sinter fines destined for Tata's furnaces at Jamshedpur. Hewitt-Robins Div. of Litton Industries was awarded the turnkey project on the basis of world- wide competitive bids. Eighty miles southwest of the city of Jamshedpur, Noamundi lies on an approximate geographic grid of 22º-5' latitude north and 85º-30' longitude east. The mine is approximately 600 ft above sea level.

Jan 11, 1968

By S. E. Haszko

SEVERAL new XGa2 intermetallic compounds, Table 1, where X is a rare earth, having the AlB, structure were prepared as part of a continuing study of the magnetic and structural properties of rare-earth alloys.' In this note, the crystallographic results of these compounds are presented. Chart, Eq. 121 for the data in Fig. 1 can be adequately represented by The corresponding standard free-energy change is AF; = -4.576 T log K = -20,900 + 10.20T [5I At low nitrogen concentrations the ratio of mole fraction to weight percentage is a constant so that the mole fraction X of nitrogen is given by X = 0.0392 [%NJ. At low values of X, the activity and the concearation approach each other, hence K, = 0.0392 K,, where K, is expressed in terms of the mole fraction of nitrogen. Hence Eqs. [4]. and [5] become

Jan 1, 1962

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, graduate engineer, aged 44, with over 22 years' experience in connection with the development of large coal and coke properties in different parts of the country, desires position as general manager or general superintendent of large bituminous coal producer, or will take an interest and the management of a smaller operation. No. 258 Member, aged 41, mining engineer, manager or general superintendent, 20 years' experience, 10 years in Mexico, 5 years Western States, 5 years abroad. Guarantee results, fluent Spanish, excellent references. New York interview. No. 282. Member, technical mining graduate, 10 years' experience, especially in design, erection, construction and purchase of power and mining equipment and supplies, desires position in purchasing department. Married, aged 32, employed at present, references furnished. No. 295.

Jan 6, 1916

By D. R. George

Preliminary research has identified several organic and aqueous solutions that are effective absorbents for SO, from simulated smelter gas containing 0.3 to 2% SO2. These SO2 loaded solutions are also compatible to the reaction of H2S and SO2 to precipitate a readily filtered elemental sulfur. The economic removal of SO2 and production of elemental sulfur from stack gases discharged by base- metal smelters is a challenging goal. The magnitude of this task is illustrated by the estimate that about 3.5 million tons of SO2 are discharged to the atmosphere by smelters annually in the U.S. The SO2 concentration of the gases ranges from about 0.5 to more than 3%. As the sulfur content of SO2 is 50% a potential production of 1,750,000 tons of sulfur per year is indicated.

Jan 1, 1970

By Richard L. Gordon, Charles J. Johnson

Electric power demand doubles about every ten years, and because of the associated burgeoning fuel requirements, power stations absorb over half of the coal output in the United States. Throughout the 1960's, demand for coal utilized to generate electricity grew at an average annual rate of 6.5% but coal producers held back greater expansion because they expected nuclear plants to proliferate faster than they actually did. Even so, the growth rate is expected to continue at the 1960's rate until at least 1976. The continuation of the 6.5% growth rate beyond 1976, however, will require additional orders for coal-fired plants during the early 1970's. In fact, plants consuming a total of 130 million tons of coal must be ordered in the next few years. If the requisite plants materialize, total 1980 coal output for electrical power generation will be approximately 600 million tons.

Jan 1, 1971

By D. C. Bard

THESE notes are based on the megascopic study of a suite of 2,400 specimens of minerals and ores from the Butte mines, combined with field observations at intervals over a period of several years. The estimate of average vein composition is based on field acquaintance with the veins. It is probably correct in its broader proportions, and should be of use for comparison. Chemical and Mineral Composition of Butte Sulphide Vein. Matter. Per Cent. Oxygen 43.00-Quartz, rhodonite, rhodochrosite, barite, calcite, and hübnerite. Silicon 36.00-Quartz, rhodonite, and willemite (very rare). Sulphur 5.00-Sulphides of. iron, zinc, copper, lead,. and sulphates of barium and rarely calcium. Iron 5.00-Ferric sulphides (pyrite, bornite, chalcopyrite), also in sphalerite, tetrahedrite, and rarely hematite and siderite. Manganese, . . . . 2.00-Rhodonite, rhodochrosite, and hübnerite. Zinc, . . . . 1.00-Spha erite, very rare wurtzite and willemite, and tetrahedrite and tennantite.

Jan 8, 1913

By B. P. Bellport

When tunneling crews set world records in rates of advance by boring up to 403 ft in a single day and 6851 ft in a month, then the age of rapid under- ground excavation is near at hand with its attendant economies. Boring machines excavate tunnels with uniform diameters and smooth walls and only about 5% overbreak compared to 20% overbreak experienced by conventional drill-blast methods. This advantage minimizes the concrete required for lining and because a circular section is more nearly self-supporting there is less of a need for supports before the concrete is placed. In addition, laser beam guidance improves the accuracy of excavation with boring machines. In the first successful application of laser guidance for boring machines in the Navajo Indian Irrigation Project, the final excavation was within 5/8 in. of the established line and grade over a 10.079- ft advance.

Jan 1, 1971

By James S. Browning

The Mineral Resources Institute and State Mine Experiment Station of the University of Alabama conducted Humphreys spiral tests on fine coal waste from nine preparation plants of Alabama strip mining operations to determine the feasibility of recovering low ash and sulfur fuel meeting steam coal specifications. The ash in the samples ranged from 9 - 5l%, and the total sulfur ranged from 0.4J- 2.39%. Continuous laboratory tests using a Humphreys spiral gave good recovery of the coal with excellent rejection of the ash and pyritic sulfur. Coal recoveries of 83.6 - 94.1% were achieved from the different samples. Ash content of the clean coal products fell within a range of 5 - 12.2%, with a total sulfur content of 0.62 and 1.10%. In quality, the products were comparable or superior to those now being shipped from the preparation plants.

Jan 1, 1980

POSITIONS VACANT A steel manufacturing company is desirous of securing an assistant superintendent for its plant. Experience in open-hearth plants and in rolling mills particularly desirable. No. 112. Opening as assistant superintendent of a non-ferrous smelting plant. Man with metallurgical experience preferred but chief essential is ability to handle men. No. 114. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, aged 41, mining engineer, manager or general superintendent, 20 years' experience, 10 years in Mexico, 5 years Western States, 5 years abroad. Guarantee results, fluent. Spanish, excellent references. New York interview. No. 282. Member, technical mining graduate, 10 years' experience, especially in design, erection, construction and purchase of power and mining equipment and supplies, desires position in purchasing department. Married, aged 32, employed at present, references furnished. No. 295.

Jan 7, 1916

By Parviz Montazer, Robert King, William Ubbes, Gideon Chitombo

This paper describes the results of a detailed study that was undertaken to define the spatial distribution of permeability within a five meter thick envelope around the CSM/ONWI room. Detailed fracture orientations and distribution were determined through mapping of the walls of the opening, logging of oriented core, and visual examination of borehole walls with a borescope and a T.V. camera. Over 3,500 measurements were made from which the three dimensional distribution of fractures was determined. Two principally different testing equipment designs and various methods of air injection tests were used in all boreholes to identify and characterize conductive fractures. Through analizing the distribution of permeability and fracture index around the room a zone of blast damage of approximately .5 m thickness was delineated. The effect of stress modification seems to extend farther into the host rock to approximately 3.5 m depth.

Jan 1, 1982

FOREWORD5 INTRODUCTION 7 ACKNOWLEDGMENTS II BERGBÜCHLEIN TRANSLATION OF THE TEXT 17 HISTORY AND BIBLIOGRAPHY OF THE Berghüchlein 49 NOTES ON TRANSLATION AND ACKNOWLEDGMENTS 63 THREE ILLUSTRATIONS FROM THE EARLIER UNDATED EDITION 65 [ ]

Jan 1, 1949