Search Documents

By F. J. Menzer, E. M. Schern

The Morenci/Metcalf porphyry copper mining operation, located in southeastern Arizona, currently processes approximately 91,000 tonnes of ore per day and has copper ore reserves estimated to be in excess of one bill ion tonnes. Functional groups within the Geology Department (currently staffed with six professional and two support personnel include mine geology, project geology, and hydrogeology. The primary task of mine geologists is daily preblast bench face mapping with grade and mill amenability estimates. Auxiliary duties include detailed in-pi t metal distribution evaluation, mineragraphic work and flux quarry geology. Project geologists conduct exploration and preliminary development projects both within and outside the Morenci district and provide support to ore reserve block modeling and geotechnical work performed by the Morenci mine engineering group. Hydrogeologists handle exploration for and development of groundwater resources and groundwater flow modeling, mine dump leach solution penetration and recovery evaluation, and tailing dam water reclamation.

Jan 1, 1984

By M. C. Van Camp, J. D. Miller

Preliminary results are reported regarding the design and development of a pilot scale air sparged hydrocyclone for cleaning fine coal 590 pm (- 28 mesh) containing 24% ash and 1.6% sulfur. The principle of separation is the flotation of hydrophobic coal particles in the centnjugal field generated by the fluid flow in the air sparged hydrocyclone as discussed in another publication. This 152-mm (6-in.) hydrocyclone has a nominal capacity of 0.9 t/h (1 tph) and experimental results suggest that separations vastly superior to a water-only cyclone are possible. In addition the separation efficiency is as good, if not better, than that achieved with conventional flotation cells. For example, typical results indicate that 75% clean coal can be recovered at 15% ash leaving a tailing product of almost 50% ash. These experimental results coupled with the high capacity of the air sparged hydrocyclone (imagine a retention time for flotation of only two seconds compared to two minutes for conventional flotation) may represent a significant breakthrough, not only in coal preparation technology, but in the flotation of fine particles in general.

Jan 1, 1983

By Ben L. Seegmiller

Localized open pit slope failure was avoided as an apparent result of a practical rock mechanics program conducted at the Twin Buttes copper operation. The key to the program was the application of cable bolting, a technique that artificially supports open pit slopes using properly installed post-tensioned cables. As a result of the research and testing program, extensions of the cable bolting principal became significantly apparent. • The economics of artificial stabilization appear to be overwhelmingly favorable, and • Best practical applications are "final" pit slopes, slopes beneath permanent structures and potentially slope failing areas. Success of this research is manifested by the fact that similar stabilization systems are presently under consideration for Twin Buttes as well as other open pit operations.

Jan 12, 1974

By Oscar Aguilar, Jin-ichi Nakamura, Kazuo Nakamura

Michiquillay deposit is porphyry copper type with over 500 million tons of 0.70% Cu ore. In order to reflect the true nature of the orebody as to shape and value distribution and to compensate for insufficient data in the outer perimeter and lower portion, "Triangular Interpolation Method" is used in the computation, wherein block grades are determined by "Plane Regression". The results thus obtained are compared with the data from additional investigation and are found to match well with each other. Aside of total Cu, assays of Fe, S, MoS2 and geological data such as alterations, rock types, faults, mineralogical compositions are also stored in the computer. By this system, their distribution and relation to alteration become clear and classification of ore into types affecting recovery become possible. The outputs of this system make clear the characteristics of the orebody and furnish valuable geological data on the orebody.

Jan 1, 1976

By Daniel L. Murphy

The iron ore province of Quebec and Baffin Island trends from the southern shore of Baffin Island northeasterly through the Labrador Trough to Matonipi Lake, approximately 185 miles northwest of Seven Islands, but future geologic field studies will very likely extend the limits of the province to include the ferruginous and associated rocks of the Lake Mistassini area. Recent improvements in the beneficiation of low-grade iron ore have stimulated widespread exploration for deposits amenable to concentration, particularly along the southwest extension of the Trough. GENERAL LITHOLOGY Pleistocene and recent deposits of clay, sand, gravel and erratic boulders cover roughly 60% of the land surface. All of the bedrock is of Precambrian age (Table I). Paragneisses and paraschists together with metasedimentary iron-formation, marble and quartzite are abundant and, for the most part, appear to be metamorphic equivalents of the relatively unmetamorphosed rocks of the Labrador Trough to the north beyond the "Grenville Front." Bodies of amphibolite are widely scattered. A large portion of the metamorphic rock shows some degree of permeation by granite material as well as alteration by hydrothermal solutions. The youngest bedrock consists of a complex containing slightly altered ultramafic to monozonitic intrusives.

Jan 9, 1962

By R. I. Williams

Kennecott Copper's mining activities in Arizona are conducted by the Ray Mines Div., located in Ray, Ariz., in the Mineral Creek mining district about 60 miles southeast of Phoenix. The Ray orebody lies in a mineralized zone belted on the east, west, and north by well defined faults. The orebody consists principally of schist with intrusions of quartz porphyry and diabase. The dominant ore mineral in the schist and quartz porphyry is chalcocite, with some native copper, and in most areas the orebody has been heavily oxidized. In the diabase the dominant ore mineral is chalcopyrite. Ore deposition in the schist portion is very erratic, with no apparent structural explanation. In 1873 silver prospectors opened the mining district, but it was not until 1899 that an English company made the first major attempt to exploit the copper deposits. This venture failed because of improper sampling and limited development work. In 1904 D. C. Jackling, Seeley Mudd, and Philip Weiseman became interested in the Ray Copper Co. and the Gila Copper Co., which later merged as Ray Consolidated Copper Co. In 1926 the Nevada Consolidated Copper Co. took over Ray Consolidated and in turn was taken over by Kennecott Copper Corp. in 1933. The extensive program of surface and underground development and exploration begun in 1907 continued through successive changes of management and ownership to the present time.

Dec 1, 1956

By Betty J. Laswell, Gerald W. Laswell

If recent trends in the rotary drill market are indicative of future surface mining operating practice, then the move to scaled-up mining equipment by manufacturers may soon be over. Of the 48 different rotary drills currently produced by 12 manufacturers, over 60% were introduced within the past five years. By far, the new drills have been in the "small" class, capable of producing up to a 229-mm-diam (9-in.) blasthole with 222 kN (50,000 lb) or less of down pressure. New rotary drills in the "large" class, capable of producing a 311-mm-diam (12 1/4-in.) blasthole with up to 423 kN (95,000 lb) down pressure, have also been prominent. In the super-size category, new drills producing blasthole sizes to 444-mm-diam (17 1/2-in.) with up to 578 kN (130,000 lb) have been minimal.

Jan 7, 1978

By G. F. Tagg

EARTH-REISTIVITY measurements are often of service in obtaining information regarding geological formations, particularly when applied to structural problems. In such problems the masses of the various bodies are large, and have a corresponding effect on the average resistivity of the soil. Much work has been done using such measurements, but in general the method of interpretation employed is empirical. Since certain simple cases can be investigated mathematically, it appears to be quite sound to endeavor to apply the mathematical solutions to the practical results, in order to deduce from the latter such unknown quantities as depth. This paper deals with such a method of interpretation for the simple case of a single horizontal stratum. SURFACE Of EARTH In the method described by FIG. 1.-WENNER'S METHOD OT MEASURING Wenner1 for measuring earth resis- EARTH RESISTIVITY. tivity, four stake electrodes are driven into the earth in a straight line as shown in Fig. 1. A current I amperes is passed between the two outer stakes and the potential difference . V volts between the two inner stakes is measured. Then if a is the electrode separation, the specific resistance of the soil, which is assumed to be homogeneous, is given by the formula

Jan 1, 1932

By A. J. Teplitz, R. J. Goodwin

A new type water shut-off for use in air drilling has been developed. The method has been 99 to 100 per rent effective in several different formations of inter-ranular-type porosity. Since costs for materials, time and equipment used are relatively small, the process should extend economies of air drilling to many new areas. The treatment involves a new technique for forming a water-inroluble precipitate within the pores of a rock. Advantage it taken of the difference in mobility of a liquid and a gas in porous media to achieve the greatest volume of precipitate in a given pore. Reactants selected for the laboratory (2nd field tests were aluminum sulfate solution and gaseous ammonia. This process has been tested in both intergranular and fractured-type porosities. It has consistently shut-of between 99 and 100 per cent of the water flowing from formations having intergranular-type porosity and perrlreuhilities ranging from a few millidarcise to over a darcy The treatment is not particularly suitable for shutting-off water from fractured formations although plugging of the order of 50 per cent or greater has been achieved in all such applications. Among advantages of the treatment are: (I) no reaction waiting rime after a relatively short placement time, (2) a low mate-rials cost of about $3/f1 of hole treated, (3) use of common service-type equipment for treatment, and (4) no unusual requirements for mixing and placement. INTRODUCTION In rotary drilling with air or gas it has been possible to increase bit life by tenfold and more than double rate of penetration over corresponding performance when drilling with mud. These factors have amounted to as much as 22 per cent savings on total cost of drilling a well. However, these advantages are rapidly lost when water is encountered in an air- or gas-drilled well because water interferes with the removal of cuttings from the hole and also gives rise to other difficulties. In attempting to combat water troubles, operators have commonly resorted to such measures as mist drilling, treatment with cement or chemicals, converting to conventional mud drilling, or setting casing. In many cases these measures have either been costly or ineffective. In an effort to overcome this problem, studies were undertaken to develop an effective and economical water shut-off technique for use in formations possessing inter-granular-type porosity. Extensive laboratory experimentation finally led to a unique method for producing a water-insoluble precipitate within the pores of a sandstone. The unique part of the treatment is use of a liquid and a gas to form the precipitate, and in this case the reactants used were aluminum sulfate solution and gaseous ammonia. The reaction between these two materials is shown in the following equation. Al2 (SO1)3 - 18 H20 6NH2? saturated Water- Solution Cat 2A1(OH)3 . n H20 3(NH4)2SO • n H20 Solid Solid That is, a solid precipitate consisting of aluminum hydroxide and ammonium sulfate is formed when ammonia reacts with aqueous aluminum sulfate. The aluminum hydroxide is insoluble in water and the ammonium sulfate, though soluble, can only be removed from the formation pores by diffusion—an extremely slow process. Although the precipitate formed by the reaction is not particularly firm, great strength is not needed for a precipitate to bridge and plug intergran-ular-type porosity. A flow path in such a system is extremely tortuous and involves a great variety of pore

By H. I. Aaronson, C. Laird

Although the past results of X-ray experiments indicate that the broad faces of 0' plates are coherent with their matrix, dislocations lying in arrays have frequently been observed at these boundaries by transmission electron microscopy. Critical experiments employing the latter technique have been carried out in order to determine the origin of these dislocations. It is concluded that 8' plates are essentially coherent with the matrix at their broad faces throughout the aging temperature/time envelope studied. Virtually all of the dislocation arrays observed are deduced to have been formed by plastic deformation accompanying transformation. The proportion of dislocations arising from convexity of the plates is shown to be negligible by comparison with that from plastic deformation. At the higher aging temperatures, a[001] dislocations appeared in moderate numbers. These dislocations were traced directly, however, to the ledgewise dissolution of 0' occasioned by the formation nearby of 0 crystals. On the other hand, since there is a parametric difference normal to the broad faces of the ?' plates, mismatch dislocations do form at their edges. A previous conclusion that these dislocations have Burgers vectors of type a[001] was confirmed directly. The edges of 0' plates were observed to develop octagonal shapes when growing, but circular shapes during dissolution. 1 HIS paper presents the results of an investigation of the interfacial structures of plates of the transitional phase, 8', formed in an A1-4 pct Cu alloy. In a companion paper, Part 11, the effects of these structures upon the migration kinetics of a:?f boundaries are reported. This work is pa.rt of a general program designed to establish the basis of precipitate morphology. The present authors in Al-Ag,1 and whitton2 previously in U-C alloys, have used transmission electron microscopy to examine directly the vander Merwe3-6 networks of dislocations anticipated7 to compensate the small amount of lattice misfit normally founda at the broad faces of Widmanstatten plates. Since the broad faces of 0' plates are considered to be perfectly coherent with the corresponding habit planes in the a matrix,' no dislocations should be present at these faces. Many reports have been published, however, giving evidence to the contrary.10-18 The primary objective of this investigation was therefore to ascertain the nature of these dislocation structures. An attempt to do this is described in the first three sections of this paper. Inspection of the matching of the a and 8 ' lattices at the orientations of the 0:0' boundary corresponding to the edges of 0' plates raises the possibility that these edges may be made up of rather closely spaced edge- type misfit dislocations oriented so as to be sessile with respect to the lengthening or shortening of the plates. Since this structure should severely inhibit migration of the plate edges (Ref. 7, Part II), a situation not originally anticipated,' an experimental determination of the interfacial structure of the edges of 8' plates was clearly in order, and is reported in Section III. Those aspects of the experimental procedure applicable to both Parts I and I1 are presented in the next section. Specific procedures applicable to individual aspects of each investigation, and also the relevant surveys of the literature, are then individually reported in the appropriate sections. I) GENERAL EXPERIMENTAL PROCEDURE The material used in both parts of these studies was the same as that of a previous investigation:" strips of A1-3.93 pct Cu, 0.009 in. thick, prepared as before, solution-annealed at 548°C for 6 hr, and quenched. Details of subsequent aging, and in some cases deformation treatments, are given in the Experimental Procedure sections of the individual parts of both papers. Specimens of the heat-treated strips were electro-thinned as beforeLg and examined in a Philips EM 200 microscope equipped with a goniometer stage. A commercial hot stage, of the grid-heater type and capable of * 30-deg tilt about one axis in the plane of the specimen, was also used for kinetic studies. The usual precaution of calibrating for the additional heat supplied by the electron beam was taken.19 A 16-mm cine cam-I era mounted outside the viewing window was frequently used to record the transformations. Conventional selected-area diffraction and dark-field viewing techniques were used to identify the precipitates in the foils. Normal bright-field images corresponding to two-beam diffracting conditions or dark-field images were employed to characterize the dislocations observed at the interfaces of the precipitates. The application of these techniques to the study of an interphase boundary, and the interpretation of the images,20'21 has been fully described in a previous paper.'

Jan 1, 1969

By R. F. Krueger, L. C. Vogel, P. W. Fischer

Previous studies have shown that the permeabilities of sandstone cores are markedly reduced following exposure to drilling fluid and subsequent clean-up with oil at high-pressure gradients. Laboratory experiments reported in this paper indicate that permeability damage from drilling mud or water can be substantially avoided through use of an initial low-pressure gradient followed by gradually increasing gradients during clean-up by reverse oil flow. On the other hand, attempts to improve the permeability of damaged Berea and oil formation cores with high-rate oil backflush (simulated well stimulation) and low-rate clean-up gave erratic results. Essentfully complete permeability repair was achieved in most of the fresh water-damaged cores from Miocene and Pliocene oil-producing formations; only minor improvement was noted generally in tests with both water-and mud-damaged Berea sandstone. Field well stimulation treatments using high-rate back-flush resulted in long-term productivity improvement when production was brought in at gradually increasing production rates and then restricted to a steady value less than the maximum possible rate. Wellbore plugging at high production rates correlated with increasing solids content in the produced oil. Observations and results from these tests agree with current concepts that formation damage in water-sensitive rocks results from movement and bridging of formation fines, rather than from clay swelling alone. INTRODUCTION Many laboratory studies1-g have shown that the permeabilities of sandstone cores are often markedly reduced following exposure to fresh water or water-base drilling mud filtrate. However, work with cores in the restored state has demonstrated that, although permeabilities to water may be very low for sandstones containing hy-dratable clays, flow of oil can often restore a substantial portion of the effective permeabilities to oi1.Neverthe- less, water invasion into water-sensitive sandstone cores results in varying degrees of permanent reduction in permeability to oil.24' Based on field data, Wade's statistical study" of well completion effectiveness also indicated a correlation between productivity damage and water invasion during completion. Similar damage can result from fluid invasion during workover. Nowak and Krueger' and Bertness4 observed in their early work (1951-53) that formation damage in water-sensitive sandstones was associated not only with swelling of expandable clays but also with movement of dispersed particles. Subsequent work by Monaghan et al." (1959), Atwood'' (19641, Mungan" (1965) and Gray and Rex'" (1965) has led to general acceptance of the hypothesis that permeability damage in water-sensitive formations is caused by migration of finely dispersed minerals and bridging in "brush heap" arrangements at pore constructions. In laboratory studies, Monaghan et al.' found the use of chemicals to be of only minor value for repairing formation damage. Atwood? however, was successful in substantially repairing damage in a number of low-permeability cores using an n-hexanol flush. In the field, except for treatments with acids, the use of chemical washes to reduce wellbore damage has had limited and sporadic success and generally is unpredictable. A statistical analysis of stimulation treatments in silt-blocked wells has shown that physical manipulation of wash materials is more important than chemical composition." The recent work reported on formation damage in water-sensitive sands brings to mind the results of some unpublished exploratory work done in 1954 in connection with drilling fluid studies.' This laboratory work and subsequent field stimulation treatments indicated a beneficial effect of controlled pressure drawdown and the associated production rate on formation clean-up. This paper reports the results of this work and more recent supplemental experiments on the clean-up of water-sensitive sandstones damaged by water or filtrate invasion. PERMEABILITY RECOVERY AFTER DAMAGE BY DRILLING MUD APPARATUS AND TEST SAMPLES A drilling mud circulating system was used to expose cores to simulated wellbore conditions. The mud flow system is the same as that described by Krueger and Voge17 except that no provision was made for scraping

By P. L. Russell

The use of nuclear explosives for excavation has been demonstrated to be feasible and practical. Application of nuclear explosives for overburden removal from large ore deposits appears to offer economic advantages over present methods, but under the present pricing schedule, high-yield devices must be used to obtain an economic advantage. The use of nuclear explosives presents problems not inherent in the use of conventional explosives, and thus they can be used only in areas where large explosions and associated phenomena can be tolerated. Stripping of coal with nuclear explosives does not appear practical at this time, but stripping overburden from copper or iron ore deposits may be a potential use. Even here, however, the use of nuclear explosives would require isolation, favorable topography, favorable ground-water conditions, and a low population density. If these basic requirements can be met, the use of nuclear explosives for overburden removal would offer both economic and time advantages. The possibility of using nuclear explosives for peaceful purposes was a subject for speculation as early as 1945. The PLOWSHARE Program was formally established by the AEC in June 1957 for the purpose of developing and demonstrating peaceful applications for nuclear explosives. The technical direction of the program is the responsibility of the Lawrence Radiation Laboratory, Livermore, Calif. Mining and excavation were two fields that received early consideration as areas in which nuclear explosives might be used. Knowledge gained from underground weapons testing increased this possibility, and the development of the thermonuclear device which has a small fission-to-fission ratio, reduced the hazard of radiation, and spurred interest. Nuclear explosives appear to have the greatest potential in the following mining operations: 1.— Surface Mining a) Stripping of waste for open-pit excavation b) Breaking of ore in open-pit mining c) Quarrying d) Blasting for production of aggregate, riprap, etc. 2. — Underground Mining a) Block caving application b) Crushing of ore for in-situ leaching, etc. c) Preparation of underground waste disposal areas Of the potential applications, excavation is perhaps the most obvious and the best understood, and probably the most practical for use in the near future. Large quantities of rock and earth can be moved by proper emplacement of nuclear explosives, but economic and practical relationship must be determined between the known capabilities of nuclear explosives and the required excavating to remove overburden. REMOVING OVERBURDEN IN OPEN-PIT MINING Removing the overburden is one of the largest jobs in open-pit mining. In 1960 open-pit mines produced approximately 130 million tons of coal, 108 million tons of copper ore, and 135 million tons of iron ore. To obtain this much production, an estimated 3-billion tons of overburden were removed from the coal, 216 million tons from the copper ore, and 135 million tons from the iron ore. These figures do not include the initial stripping required before ore production. For example, the ASARCO Mission mine started stripping operations in August 1959 and by mid-November 1961 had removed 46.3 million tons of material including 1.2 million tons of ore.* Initial excavation of this type offers the most favorable conditions for utilizing the earth-moving ability of nuclear explosives. EXPLOSIVE CASTING FOR REMOVING OVERBURDEN The use of explosives to remove overburden is not a new idea. Conventional explosives have been used for this purpose for many years with varying degrees of success. Several small coal strip operators have used this idea to increase production. At these mines about one-third or more of the overburden is thrown by explosives across the pit and onto spoil piles. The additional costs of drilling more blast holes and more explosives are more than compensated for by a reduction in the time required to uncover the coal, and by an increase in coal production.

Jan 1, 1964

By J. E. Johnson

At the Cleveland meeting of the Institute in October, 1912, I had the honor to present a paper outlining the conditions surrounding the charcoal iron industry…

Jan 1, 1915

Jan 1, 1913

By Mack H. Shumate

1 Raw coal from Truax-Traer Coal Co.'s Burning Star Slope mine, Jackson County, Ill., is brought to the surface by the new 42-in. slope belt haulage conveyor at the rate of 850 tph. The loading system shown above employs four storage tracks, two tail tracks for loading, and four 25-hp hoists, operating in pairs, and coupled to two dolly cars to move the trains of cars through the tipple. The system has a capacity for loading 1800 tph. One operator is needed to load on each of two shifts. A third man working for a few hours on night shift sets up for the morning cycle. Railroad crews bring in empties placing them in the storage yard, twenty cars to the track. Trains of empties are pulled through to the tail track and loaded on the return; hoists at opposite ends pull the trains in each direction. [ ] 2 Pairs of hoist drums are interconnected electric- ally by a Trench lay cable buried between the tracks. When one hoist operates moving the cars, the tail hoist idles with brake released. The operator, situated in the tipple over the cars, views the storage yard at the end of the first shift (left). When returning loaded cars to yard, four or five cars are held on the dolly to couple the next string of empties. Empties are ready for loading on the tail track (right). Differing from a gravity system in which empty and load tracks are on a slight grade, this system is designed for 80 railroad cars for a two-shift operation and one rail service per day.

Jan 6, 1962

By I. Milton LeBaron

OPERATION of the phosphate flotation plant at the Peace Valley mine of the International Minerals and Chemical Corporation, Florida, began in the summer of [ ] 1942. Since that time several changes have been made in the flowsheet, with resultant increases in metallurgical results. Three flowsheets, together with the comparative plant results, are given in this paper, together with a discussion of the desliming circuit used for preliminary washing of the flotation feed. FIRST FLOWSHEET CHANGES Fig. I lists the essential units in the original flowsheet at the Peace Valley plant. The figures for tonnage and grade are average for a period of two months. Mineral Separation Airflow cells are used for both the fatty acid and the amine float. Three immediate difficulties presented themselves in the use of this flow sheet: I. Floating a maximum amount of phosphate in the rougher section to give good recovery sent a low-grade concentrate to the silica float, resulting in high costs for amine reagent in that section.

Jan 1, 1946

By John J. Borkert, Carl E. Gerity

In situ mining offers a new and proven method of exploiting sedimentary uranium deposits. The feasibility and economic evaluation of exploiting a uranium reserve by either open pit or underground mining should also include a similar study for in situ mining. This report compares the economics of mining several hypothetical uranium deposits at various depths, grades and reserve sizes by open pit and in situ mining. The evaluation process evolved establishing, where possible, common geological and logistical parameters to both methods of mining. The various assumptions that are unique to either open pit or in situ mining were also drafted, where possible, as equal and common functions to be used in each economic evaluation of the reserve models. After the various parameters were defined, they were programmed to an economic analysis of the various hypothetical uranium deposits by the selected mining method. From the vast array of cost evaluations, total capital and operating cost per pound U308 produced, DCF-ROI, and total net profits before State and Federal taxes were selected as the most meaningful results to compare. From the various geologic parameters used, it was determined that the economic viability of a mining venture is most sensitive to a depth-grade thickness ratio. The three selected evaluation products were plotted against the various depth-grade thickness ratios of the hypothetical uranium deposits. The results of the economic cost analyses show in situ mining generally to be a better method to maximize total net profits and to maximize return on investment.

Jan 1, 1979

By Martin J. Conway

DURING the past year, the intense interest shown by the metallurgical industry in the use of relatively pure oxygen has been evidenced by the number of papers dealing with its application and production. The reason for this interest is apparent when it is realized that, weight for weight, oxygen enters into the formation of steel equally with iron. In the manufacture of steel, approximately one ton of oxygen is required to produce one ton of ingots. Until the recent development of plants capable of producing oxygen at far lower costs than had ever previously been considered possible, the oxygen required for steel manufacture was used as it occurs in air, where it is associated with approximately four times its volume of nitrogen. Because of the diluent nitrogen more than 4 tons of total gaseous material per ton of steel must be handled rather than only approximately one ton required when pure oxygen is used. In addition, provision must be made to handle the large quantity of waste, gases resulting from the process. There are cases where the reduction in gas volume alone can justify the installation of an oxygen plant.

Jan 1, 1947

By H. W. Schreiber, H. R. Babitzke, R. E. Rodriquez, Patterson J. A., C. D. Masters, J. J. Schanz, R. B. McCammon, E. A. Noble, P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on uranium resource evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources (ASTM Standard E901-82, April 1983). The standard classification was prepared with participation of representatives from the US Department of Energy, the US Department of Interior's Geological Survey and Bureau Mines, utilities, and consultants. The classification a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alphanumeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that remain infixing the classification a given uranium resource include uncertainty in estimating the quantity of undiscovered resources and resolving differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1985

By James Barr

WHEN phosphate mining operations first commenced in Tennessee the loss of both high- and low-grade material was large, because of the crude hand methods employed. Practically all rock smaller than 2 in. was thrown back into the pits and covered with the overburden of subsequent openings. With the advent of mechanical washers and other mining machinery, together with the abolishing of the contract system, the waste has been steadily diminished, until at present only the finest sand is being rejected; and even this is not lost, for in the majority of cases the water, slime, and sand from the washers are run into large settling ponds where practically all of the phosphate-bearing material is caught and stored for future use, or until it is profitable to ship lower grades. The latest equipment used to recover the fine and lower-grade phosphate sand includes Dorr thickeners, settling tanks, Dorr classifiers and settling ponds served by locomotive cranes with clam-shell buckets, making it possible to save material averaging as fine as 200 mesh. To attempt saving finer material would necessitate a different type of drier, which might be patterned after the multiple-deck roasters. The present tailing runs from 15 to 25 per cent. of available phosphate, which, however, as mentioned before, does not represent a total loss to possible future operations. The demand of the consumer is the greatest factor in regulating the recovery at present. In the mining of blue rock, which does not require washing treatment, the main waste material is the capping of low-grade kidney forma-tion, generally used for backfilling of the rooms. By reason of the introduction of improved methods in the early stages and the re-mining of territory skimmed over at the start, at the present time the net result of all operations is a comparatively small loss.

Jan 2, 1916