Search Documents

By A. L. Barnes

A number of reservoirs have been partially invaded by bottom water. Water flooding such reservoirs can be especially inefficient if the oil has a high viscosity because injected water will under-run the oil and emerge at producing wells without having displaced much oil. A possible means of improving water sweep efficiency would be to precede the water flood with a slug of water purposely thickened with a chemical additive. This possibility has been studied with a scaled laboratory flow model. The investigation was carried out on a model representing a 20-acre five-spot with one set of reservoir condition~. Displacements were performed with water, with viscous-water slugs of 10 and 25 per cent of the pore volume followed by water, and with all viscous water. Displacement tests were made at several rates of injection. For all cases, compared at the same producing water-oil ratio, an increase in rate resulted in an increase in volumetric sweep. The larger the quantity of viscous slug injected, the greater the crossflow of oil ahead of the displacing front and, thus, the lower the WOR during that period of a displacement. This investigation indicates that the injection of aqueous viscous slugs in this type of system would give some additional benefit over conventional flooding by (I) reducing the life of the flood, (2) reducing lifting costs and (3) increasing ultimate recovery. The benefits of a viscous-slug displacement would warrant its use if the viscous water could be created for a few cents per barrel. INTRODUCTION The most appropriate method for water flooding oil reservoirs which have been partially invaded by bottom water has been a problem of considerable interest. Such reservoirs, having good vertical permeability and unfavorable mobility ratios, are difficult to produce efficiently under normal waterflood procedures. Even though the injection wells have been plugged back above the oil-water contact and the water zone has been squeezed off, injection water will enter the formation and not only displace oil, but also much of it will displace the bottom water, thus creating a high producing water-oil ratio at the start of a flood (see Fig. 1). Since the rate of injection and the viscosity of the displacing fluid are the more easily controlled physical parameters of the reservoir, it is quite natural to study their effects on the volumetric sweep of the oil zone and on the producing water-oil ratio. Increasing the viscosity of the displacing fluid has two disadvantages—it reduces the maximum rate of injection into the reservoir, and it costs more than water. It was thought that the injection of a viscous-fluid slug, followed by water, would minimize these two disadvantages, increase the volumetric sweep of the oil zone and reduce the producing water-oil ratio. Water with an additive to increase viscosity would probably be the most effective. The primary purpose of this investigation was to determine the feasibility of injecting viscous-water slugs followed by water to improve or hasten oil recovery while reducing the producing water-oil ratios. The effect of injection rate upon recovery was also investigated. A laboratory model, scaled to a 20-acre five-spot prototype with one set of reservoir conditions, was constructed. Laboratory studies of displacements with (1) water, (2) viscous-water slugs of 10 and 25 per cent of the pore volume followed by water and (3) all viscous water were performed at several rates of injection. THEORY OF SAND MODEL SCALING There are two conventional means of determining scaling criteria. These are dimensional analysis and inspec-tional analysis. Determining scaling criteria by dimensional

By C. E. Sims, G. A. Moore, D. W. Williams

During the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging, The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary ab- normal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. I, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. 'The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.' Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period of approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the System could be degassed thoroughly in

Jan 1, 1949

By R. J. Sandrea, S. M. Farouq Ali

The results of an experimental and theoretical study of the effects of rectilinear impermeable barriers and highly permeable channels on the sweep efficiency and conductivity of a five-spot network are presented. The study was carried out using Hele-Shaw, and conductive sheet analogs for both. normal and inverted flood patterns. A functional relationship was developed which provides quantitative prediction of the above parameters; i.e., sweep efficiency and conductivity, for the nonhomogeneous system. To evaluate this, it is necessary only to measure the interference modulus of the obstacle using a simple expression. The results indicate that impermeable barriers, with an interference modulus greater than zero, always cause a decrease in the conductivity and the sweep efficiency of the pattern. On the other hand, permeability channels do not have a significant effect on these parameters, unless they are located along the streamlines. The study also discusses a method of formulating the difference equations pertaining to the two-dimensional Laplacian in a system containing rectilinear barriers. In addition, a technique is described for tracing the progress of a free surface, using marked particles, in a stream containing discontinuities SuCh as those occurring at the extremities of barriers. The above computational scheme was used in a digital computer program to simulate results of the Hele-Shaw analog. The computed values of sweep efficiency mere in good agreement with the experimental values. INTRODUCTION At the present time waterflooding remains the most widely used technique for the secondary recovery of oil. Among the numerous factors that affect the performance of a waterflood, the areal sweep efficiency constitutes one of the most critical parameters. It is a function only of the geometric distribution of the wells for a homogeneous medium and unit mobility ratio. Geological considerations, however, such as the presence of sealing faults or solution channels in the rock matrix, would generally exert an adverse effect on the areal sweep efficiency of a waterflood network. Surprisingly little information is presently available on the quantitative implications of such permeability interferences. It was the object of this investigation to consider the presence of rectilinear, impermeable and highly permeable interferences in an otherwise homogeneous five-spot pattern, and to analyze their effects on the resulting sweep efficiency and pattern conductivity. The experimental phase of the study was conducted using two different models: the Hele-Shaw flow cell and the field plotter. For experimental convenience, the geometric boundaries of the five-spot were assumed to constitute streamlines even in the case where the interference was asymmetrically placed with respect to a repeated five-spot pattern. A second object of the study was to develop a computational scheme for numerically calculating the pressure distribution in a five-spot flow pattern containing rectilinear, impermeable barriers, and to use this distribution to compute the sweep efficiency. EXPERIMENTAL PROCEDURE HELE-SHAW ANALOG The Hele-Shaw analog was used both as a visual model and for determining the sweep efficiency for systems involving impermeable barriers. The physical limitations of this model as a means of experimentally studying the motion of a fluid in porous medium have been adequately discussed elsewhere.2,7 Likewise, it can be easily verified that the analogy remains valid when a portion of the region between the plates contains an obstacle of the same thickness as the distance between the plates. The model used in this study was composed of

By C. Kremer Bain

UNDER present economic conditions the necessity of mechanizing the mines of our country has become a very important problem. More and more mines are looking toward increased or complete mechanization of their operations, so in the writer's opinion it is quite pertinent that some of the associated problems that accompany such a program be pointed out. The following generalization on attempting a comparatively slight change in mining methods at the Southeast Missouri properties of the St. Joseph Lead Co. is an attempt to point out to anyone faced with a mechanization program that much time and C. KREMER BAIN, Member AIME, is Assistant to General Manager, St. Joseph Lead Co., Bonne Terre, Mo. AIME Sun Francisco Meeting, February 1949. TP 2743 A. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Dec. 27, 1948; revision received Oct. 13, 1949. effort can be saved, and many headaches avoided, if company policy can be established whereby everyone in the organization from the top down is desirous of improvement and is working towards the common objective. Any changes in mining methods, machinery, and so on, must entah coordination of all the other phases of mining as they all have to mesh as accurately as a smooth running chain of gears if satisfactory results are to be obtained. The purpose of this paper is to point out some of the problems which :have to be surmounted when any mechanization program is attempted, rather than to go into the mechanical details and actual operating data of the equipment employed. After all, machines have to be adapted to best suit the local conditions, so no general formula can be given that would apply to other properties. Although St. Josepll Lead Co. has been mechani-cally-minded for a number of years, as shown by the fact that over 110 million tons have been loaded mechanically since 1922, any further mechanization or changes always present a problem. When our ore bodies were of great height and area the breaking and loading were developed to a high degree of efficiency according to known standards. But in recent years, when our ore bodies became smaller and more scattered, the amount of tonnage we were able to break was not sufficient to supply our shovels with enough rock to keep them working to capacity. Our first step in attempting to rectify this situation was to develop a technique of moving the shovels to the broken ore in various stopes, which sometimes entailed a move each shift. A shovel is not producing when being moved, so within the last two years we have been endeavoring to devise some means of getting more rock broken in these smaller stopes and it was then that we became interested in jumbo drilling. To illustrate the fact that mechanization is a process of a chain of developments rather than a stroke of genius can best be shown by a general summary of conditions and obstacles which were encountered in our present attempt to establish template drilling of a standardized round. Our first jumbo was more or less the conventional type with two machines mounted on a crossbar. This arrangement proved to be impractical to duplicate satisfactorily the regular routine of slabbing in a more or less radial pattern as carried out by column drilling. One machine was either too close to or too far from the face and there was another disadvantage in that one drillman was frequently delayed while waiting for his partner to bottom a hole. Our next step was to eliminate the crossbar so the machines could operate independently of each other, but we still encountered the same objections mentioned above except that one drillman was free to drill three holes instead of one in a vertical plane independently of his partner. Time studies while trying to adapt the jumbo to the regular slabbing practice as accomplished by column drilling, revealed that twice as much time was spent in maneuvering the jumbo into position and aligning the holes as was consumed in drilling.

Jan 1, 1951

By Reinhardt Thiessen

Under sulfur in coal, is usually understood that form of sulfur which is combined with iron and known as pyrite. It occurs in the form of balls, lenses, nodules, continuous layers, thin sheets, or flakes, both in horizontal planes and vertical cleavage fissures. But pyrites also occur as very fine microscopic particles, or nodules, disseminated through the compact coal. This form has had but very little consideration. Finally, there is sulfur in coal in an amicroscopic form (not visible with an ordinary microscope), probably combined with the organic matter that exists in the coal. This form has had considerable attention from a scientific standpoint, but has probably not been recognized enough on the economic side. One or the other, or both, of these two latter forms may comprise the larger part of the sulfur content of coal, especially after it has been washed or otllerwise prepared for use. Pyrites in Microscopic Particles All coals that have been examined by the author contained a varying amount of sulfur in very small globules, or particles, of pyrite. These particles are seen in a thin [section as roughly rounded opaque dots, Figs. 1 to 10. When isolated, they are generally shown to be approximately spherical in shape, with a rough outer surface. They vary in diameter from a few microns to a hundred microns, the majority messuring from 25 to 40 microns; relatively few exceed the latter diameter. They are, therefore, very small objects. Their size is best appreciated by comparing the illustrations, in which they are shown. at a magnifiea tion of 100 diameters, with some known area like the period used in the ordinary printed page. The period is about 0.6 mm. in diameter, and . when magnified 100 times, will cover a circular area of about 2 1/2 in. in diameter, or all but the corners of the illustrations. The illustrations, therefore, represent an area about as large as an ordinary period, and the pyrite globules form but a small part of the total area. Very frequently a number of these particles are joined together in horizontal rows; oc-

Jan 1, 1920

By Gregoire Gutzeit

THE development reported in this paper was begun by the author a number of years ago, while he was a lecturer on complex chemistry and metallurgy at the University of Geneva, Switzerland, and in charge of that institution's research laboratory. Completion of the development and reduction to practice did not occur until last year at the Westport mill, laboratories and testing plant of the Dorr Company, where this method is now in general use for identifying and localizing the mineral constituents of both metallic and nonmetallic ores. It has proved to be a practical tool of the metallurgical staff at the Westport mill, devising unusual milling flowsheets for complex and refractory ore bodies. In a number of instances the findings have been successfully used as fundamental factors in the design and specification of complete metallurgical plants. Seven examples of the use of this method in solving practical milling problems are included in this paper. GENERAL OUTLINE The microscopic study of an ore, at first only of scientific interest, has proved extremely useful both in practical geology and in ore dressing. The binocular magnifying lenses for rough observation of the products of an ore-dressing plant have been in use for a long time; but only within the last few years has a systematic microscopical examination of ore samples become a normal tool of any research laboratory dealing with ore-dressing problems. Such an investigation avoids considerable loss of time as well as empirical trials and useless experimentation. It will generally indicate the correct grinding and often will suggest the proper method of treatment. The petrographic determination of transparent minerals in thin sections, or even in grains, has been perfected, and very accurate methods have been devised to meet any requirement, such as Feodorof's rotating stage on the petrographic microscope. Almost all transparent minerals can be positively identified by their optical properties; i.e., isotropism, anisotropism, color, pleochroism, refractory index, cleavage, crystal form, birefringence, and others. The identification of opaque minerals is a much more difficult problem and can be done only by using polished specimens. Unfortunately, most of the valuable metallic ores, and even some of the nonmetallic ones, are not transparent; therefore it has been necessary to develop a special technique for the determination of these minerals. Some optical properties-for instance, isotropism, anisotropism, color, cleavage, reflecting power-are often adequate in roughly classifying the mineral. Only "reflecting power" is a measurable value, provided special photometric equipment (ocular photometer or Orcel's photoelectric cell) is available. The other optical properties mentioned are more or less relative,

Jan 1, 1942

By W. R. Strickler, P. Hazebroek, M. Prats

The pressure and production behavior of a homogeneous cylindrical reservoir producing a single fluid through a centrally located vertical fracture of limited lateral extent was determined by using mathematical methods to solve the appropriate differential equation. It is assumed that there is no pressure drop within the fracture — that is, that the fracture capacity is infinite. It was found that the production-rate decline of such a reservoir is constant (except for very early times) when the flowing bottom-hole pressure remains constant. The production-rate decline increases as the fracture length increases. Thus, the lateral extent of fractures can be determined from the production-rate declines before and after fracturing or from the decline rate after fracturing when the properties of the formation and fluids are known. The production behavior over most of the productive life of such a fractured reservoir can be represented by an equivalent radial-flow reservoir of equal volume. The effective well radius of this equivalent reservoir is equal to one-fourth the total fracture length (within 7 per cent); the outer radius of this equivalent reservoir is very nearly equal (within 3.5 per cent) to that of the drainage radius of the fractured well. The effective well radius of a reservoir producing at semisteady state is also very nearly equal to one-fourth the total fracture length. It thus appears that the behavior of vertically fractured reservoirs can be interpreted in terms of simple radial-flow reservoirs of large wellbore. INTRODUCTION An earlier report1 has considered the effect of a vertical fracture on a reservoir producing an incompressible fluid. That investigation of the fractured reservoir producing an incompressible fluid was started because of its simplicity. Thus, pertinent behavior of fractured reservoirs was obtained at an early date, while experience was being gained of value in the solution of more complicated fracture problems. One of these more complicated problems, and the one discussed in this report, considers the effect of a compressible fluid (instead of incompressible fluids) on the production behavior of a fractured reservoir. In the incompressible-fluid work mentioned, it was shown that the production rate after fracturing could be described exactly by an effective well radius equal to one-fourth the fracture length whenever the pressure drop in the fracture was negligible. Because of the simplification in interpretation, it is a matter of much interest to determine whether the production behavior of reservoirs producing a compressible liquid could be described in terms of an effective well radius which remains essentially constant over the producing life of the field. The details of the mathematical investigation are given in the Appendixes. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The reservoir has an impermeable circular cylindrical outer boundary of radius re. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below the producing layer (reservoir). It is assumed that there is no pressure drop in the fracture due to fluid flow. Fig. 1 indicates the general three-dimensional geometry of the fractured reservoir just described. When gravity effects are neglected, the flow behavior in the reservoir is independent of the vertical position in the oil sand. Thus, the flow behavior in the fractured reservoir is described by the two-dimensional flow behavior in a horizontal cross-section of the reservoir, such as the one shown in Fig. 2. Production is due to the expan-

By Nicholas J. Grant, John S. Benjamin, Bill C. Giessen

In the course of a study of hard particle-duc tile binder composite alloys, interest arose in the nature of the products of the reaction between the inter metallic compound NiAl and the binder niobium. No published information was then available. A program to

Jan 1, 1967

By K. G. Colman

This text is intended to provide the operator and turn-key contractor with the basic data for sizing vibrating screens to be used in ore crushing plants. The basic capacities, modifying factors, etc. used in the area requirement calculations were developed empirically and modified to their present values based upon years of practical applications. It must be pointed out that screening is much more of an art than an exact science, however, the information presented here should provide for reasonably accurate screen sizing when applied to metallic ores .

Jan 1, 1978

By P. H. Mell

CAN the auriferous slate deposits of the Southern mining region ever be successfully worked? is a question that has been often asked me by persons seeking investments in Southern mines. As the subject is one that has given me much thought during the past few years, I have decided to present my conclusions to the members of the Institute for their consideration. Those who have had the opportunity of exploring the region mentioned above, will readily recall to mind numerous localities, to which their attention was directed by would-be miners, as "rich and desirable properties," in which there were but few quartz seams running in every direction through fine-grained talcose slate. Most of the gold in sued formations was always found disseminated through the slate, and but a small percentage contained in the quartz. Such are the deposits I propose to discuss in this paper. Of course there are many excellent quartz mines in the South that are paying the owners good profits, and many more to my knowledge, that are not being worked for obvious reasons. But it is out of the question to suppose that these slate deposits can be practically

Jan 1, 1881

By H. H. Wade, N. F. Schulz

The large quantities of iron-bearing materials, including taconite, semi-taconite," and other low-grade ferruginous materials occurring in Minnesota and elsewhere, constitute an important potential source of iron. Satisfactory grade and recovery of iron ore concentrate cannot ordinarily be obtained from these ferruginous materials by simple methods of beneficiation. Iron is distinctive in that the free metal and two of its oxides [magnetite (Fe,O,) and maghemite (gamma-Fe,O,) ] are strongly ferromagnetic. The successful magnetic separation of natural magnetite from taconite has already been established on a commercial scale. The iron in semi-taconite, how- ever, occurs largely as goethite (Fe,Os.H,O) and hematite (Fe90,) which do not respond to ordinary magnetic separation methods. Magnetic roasting converts these iron oxides to magnetite, which can, after liberation, be magnetically concentrated.

Jan 11, 1960

By A. Martens

When I was honored with an invitation from the American Institute of Mining Engineers to present a paper at the Chicago meeting on the microstructure of iron, I hesitated about accepting, as the short interval that would remain at my disposal, after other pressing matters had received attention, could not but seriously affect the work of preparing such a paper. Unfortunately my fears have been realized and my work is neither completed, nor yet as comprehensive as I should desire. Mindful of my promise, however, and recognizing that 1 have reached a point where the results of my researches may prove suggestive, I am led to present them now, trusting that this brief explanation map secure indulgence for whatever deficiencies the paper may disclose. So far as my knowledge of published memoirs and treatises extends, microscopy cannot yet be said to possess a really firm foundation. In few cases only has any systematic development of the methods of investigation been undertaken, and broad gaps remain to be filled. It is not yet possible, therefore, to give a complete survey of the field, or, indeed, to supply a text-book on microscopic metallography. As Mr. F. Osmond, of Paris, a distinguished member of our profession, has undertaken to prepare for the Chicago meeting a historic review of the work actually accomplished I need not touch on that branch of the subject; but before entering upon my special theme, it may not be out of place for me to introduce certain explanations, as furnishing reasons for the course 1 have hitherto pursued, and to offer some suggestions for the further development of the methods of microscopic investigation. In microscopic metallography, the examination has to be conducted principally with incident light. Objectives of low power, in which the distance between the front lens and the abject is considerable, are adapted for directly incident light, and in such cases the relatively great depth of the image renders it possible to examine

Jan 1, 1894

By J. T. Mackenzie

HENRY MARION HOWE, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: "Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up-by masses of graphite . . . " Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in 1900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on 'The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro- structure of the metallic matrix, Professor Howe pointed out that "such minor struc- tural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *AOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 || ARAHAMS, ALEXANDER I., Student.. .67 E. 93rd St., New York, N. Y. '13

Jan 1, 1917

By Otto C. Kopp, Thomas B. Crattie, Dennis R. Owen

Whole-rock analyses of limestones, fine-gralned dolostones and coarser-grained dolostones adjacent to mineralized breccias (Coy mine, Mascot-Jefferson City district) were compared with similar lithologies adjacent to apparently non-mineralized breccias at the new Thorn Hill section located approximately 39 km north of the Coy mine. Specimens were analyzed for Ca, Mg, Si, Al, K, Fe, Mn, Sr, Br, C1, S, Ti and P using X-ray fluorescence analysis. The concentrations of the major and most minor elements for Thorn Hill specimens fall within the range of concentrations for Coy mine specimens; however, significant differences (probability < 0.05) were noted for Fe, C1 and Br for fine-grained dolostones and for MgO, Fe and Mn for the coarser-grained dolostones. No significant differences were detected for the limestones.

Jan 1, 1985

PAUL D. MERICA,* Washington, D. C. (written discussion t).-This paper is a discussion of some of the results of a recent investigation1 of Prof. Zay Jeffries, and of his interpretation and generalizations from these results. This work I have followed with great interest and with appreciation of its value in clarifying our views on the nature of deformation in metals and its relation to structure. It is only by such close study of the relation of structure to mechanical properties that we shall ever be able to describe the latter in terms of their ultimate elements, and thus explain what are still mysteries in the mechanical behavior of metals; experiment and thought along these lines are in my opinion of the utmost value. If I, therefore, here record some of the difficulties I have experienced in understanding some of the generalizations of Prof. Jeffries, it is only in order that perhaps from the discussion may emerge a clearer and more consistent statement of hypothesis or theory in explanation of the facts discovered by him.

Jan 11, 1918

Recent start-up of a new 3450 t/d (3800 stpd) copper-zinc concentrator complex in northern Manitoba, Canada, is expected to open new reserves and dramatically cut transportation costs for Hudson Bay Mining and Smelting Co.&apos;s Snow Lake operations. The new $C33-million mill is located in Stall Lake, Manitoba, and includes a new crushing and grinding facility and two flotation circuits for the production of 23-25% copper and 55% zinc concentrates. A small amount of lead concentrate will also be recovered. The plant will produce some 145 000 t/y (160,000 stpy) of concentrates, to be shipped by rail to the firm&apos;s Flin Flon copper smelter and zinc refinery complex, located 177 km (110 miles) to the west on the Saskatchewan-Manitoba border.

Jan 9, 1979

By Robert R. Walden, LeMont West

K ENTUCKY&apos;S first acid-grade fluorspar flotation Kmill, shown in Fig. 1, was placed in operation Aug. 1, 1952, by the Pennsylvania Salt Manufacturing Co. at Mexico, Ky. During 1951 a critical shortage of acid-grade fluorspar developed and it became necessary for the company to produce part of its fluorspar requirements. In 1951 the company purchased the Crider and Lennen metallurgical fluorspar mill and an adjacent stockpile of tailing at Mexico, Ky. The tailing, assaying about 26 pct calcium fluoride, originated from log washer and jig mill concentrators in the area. As the mill did not have a fluorspar dryer or convenient rail facilities, the company leased the Burleson concentrator at Marion, Ky., where these facilities were available. At Marion, Ky., on the Illinois Central Railroad, dry acid-grade fluorspar is transported direct to the company&apos;s Calvert City, Ky., hydrofluoric acid plant. The Mexico flotation plant was reconditioned and designed to produce acid-grade fluorspar from the jig tailing stockpile. The new plant flowsheet is shown in Fig. 2. The ore feed, old tailing, which contains 10 pct of waste rock and coarse gravel assaying approximately 8 pct CaF,, is bound together by sticky clay

Jan 1, 1955

By Orville Lyons

CENTRIFUGAL force has been utilized for the dewatering of fine coal for over 50 years by means of machines commonly called centrifugal dryers. In any centrifuge the coal and water are subjected to a spinning action which usually increases in intensity as the coal progresses through the machine. This spinning action, or the centrifugal force that it induces, tears water away from coal particles and produces a dewatered coal. The effectiveness of the dewatering action for any particular machine is governed by the size-consist of the coal and the centrifugal force imparted to the water on the coal.

Jan 5, 1951

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties situated at 29 West 39th Street in New York City United Engineering Trustees, Inc. When Mr Carnegie made his gift, "for the erection of a suitable union home" for the engineering societies, United Engineering Trustees, Inc (then United Engineering Society) was chartered un¬der Chapter 703, Laws of the State of New York, 1904, for "the advancement of the engineering arts and sciences in all their branches, and to maintain a free public engineering library " The Corporation was further empowered to acquire real and personal property and to use, maintain and occupy it, with the provision that any building erected by the Corporation shall be used perpet¬ually as a meeting place and headquar¬ters for the Founder Societies Thus the Carnegie gift realized the ideal of bring¬ing the engineering societies together under one roof, and the Corporation through its members nominated in equal numbers by the four Founder Societies had the necessary authority to act for the Founder Societies in their joint in¬terests in owning and operating for them not only Engineering Societies Building, but in the course of time, Engineering Societies Library, and The Engineering

Jan 1, 1952