Search Documents

By Helmut Antrekowitsch

Nowadays nearly the half of the world zinc production is used for galvanizing. After their life span most of the galvanized products return as scrap to the steel mill. During the steel process the zinc is collected in the flue dust It is astonishing to notice that between 40 and 50 % of the zinc produced is brought into the steel processing cycle by the coated scrap while only 3 to 5 % of the zinc production can be covered by the recycling of the zinc-bearing steel mill dusts. Responsible for this worse ratio is the fact that the established recycling technologies suffer from high energy consumption, low zinc yields, halogen problems and hardly any iron recovery. A development of new or an optimization of current recycling procedures for the dusts is unalterable because of increasing zinc amounts in these residues and the rising costs for the disposal. Different pyrometallurgical recycling technologies are tested in rotary kilns and vertical retorts at the Department of Nonferrous Metallurgy, University of Leoben, Austria. Various reducing agents from carbon monoxide to hydrogen and combinations are used. The results should make it possible to draw conclusions that allow an economical and ecological judgement of the different varieties. The goal is to support the affected industry to increase the low recycling rate and prevent a loss of high zinc values in the steel industry filter dusts.

Jan 1, 2003

By Helmut Antrekowitsch

Nowadays nearly the half of the world zinc production is used for galvanizing. After their life span most of the galvanized products return as scrap to the steel mill During the steel process the zinc is collected in the flue dust It is astonishing to notice that between 40 and 50 % of the zinc produced is brought into the steel processing cycle by the coated scrap while only 3 to 5 % of the zinc production can be covered by the recycling of the zinc-bearing steel mill dusts. Responsible for this worse ratio is the fact that the established recycling technologies suffer from high energy consumption, low zinc yields, halogen problems and hardly any iron recovery. A development of new or an optimization of current recycling procedures for the dusts is unalterable because of increasing zinc amounts in these residues and the rising costs for the disposal. Different pyrometallurgical recycling technologies are tested in rotary kilns and vertical retorts at the Department of Nonferrous Metallurgy, University of Leoben, Austria. Various reducing agents from carbon monoxide to hydrogen and combinations are used. The results should make it possible to draw conclusions that allow an economical and ecological judgement of the different varieties. The goal is to support the affected industry to increase the low recycling rate and prevent a loss of high zinc values in the steel industry filter dusts.

Jan 1, 2003

By Keiji Okumura, Jiayi Shan, Jian Yang, Masamichi Sano

"A new method of deoxidation and desulfurization of molten iron with magnesium vapor has been developed. An immersion tube, which was filled with pellets of the mixture of magnesia and carbon powders, was put into the molten iron. Magnesium vapor produced by carbothermic reduction of magnesia inside the tube was injected directly into the molten iron with argon carrier gas. The effects of temperature and carrier gas flow rate on deoxidation and desulfurization were investigated. A mathematical model of the reactions was developed. The rates of deoxidation and desulfurization were controlled by mass transfers of magnesium vapor in the gas-phase and oxygen and sulfur in the liquid-phase. This method may offer high efficiency for magnesium deoxidation and desulfurization of molten iron.IntroductionMagnesium is a strong refining agent in steel-making processes1 • At steelmaking temperatures, magnesium has a very low solubility in liquid iron, and a very high vapour pressure2 • Deoxidation and desulfurization with magnesium take place essentially through the interaction of magnesium vapor with oxygen and sulfur dissolved in molten iron, and magnesium can change chemical composition of nonmetallic inclusions3 • However, addition of magnesium to the steel bath is dangerous and does not give high efficiency in the refining process4 • Furthermore, as a refining agent, the price of magnesium is higher than aluminium and CaO fluxes. In the present study, a new method of the deoxidation and desulfurization of molten iron was developed using magnesium vapour in-situ produced by carbothermic reduction of magnesium oxide. Pellets made of mixture of magnesia and carbon powders were charged into an immersion tube, which was made of alumina or graphite. The magnesium vapor was injected directly into the melt. The effects of pellet mass, experimental temperature and carrier gas flow rate were studied on the refining rate. A mathematical model of the refining reaction was proposed on the basis of the experimental results."

Jan 1, 2000

By I. Gaballah

The chalcopyrite ore's anodic and cathodic electrodissolution are studied using a Porous Pulsed Percolated Electrode (3PE) reactor. Stationary solid electrode experiments are also performed to explore the mechanism of electrochemical dissolution of chalcopyrite. Experiments with a low - grade natural ore have been carried out at 25 "C in solutions containing 1 M NaCl and 1 M HCl. Galvanostatic and potentiostatic conditions are employed. The influences of current and potential on selectivity of the chalcopyrite ore dissolution are assessed. Anodic oxidation of this ore leads to a preferential dissolution of iron bearing minerals, whereas cathodic reduction is more selective with respect to chalcopyrite. However, in both cases the electrochemical dissolution is incomplete and the current efficiency is low. Design of the actual reactor has to be modified to increase the bed conductivity and to allow continuous experimentations.

Jan 1, 1994

By Qingyu Deng, Shiwei Ma, Wang Hua, Guibao Qiu

"The flow properties of the blast furnace slag bearing high TiO2 at high temperature like the viscocity may change a lot due to the formation of the carbonitride inside, causing serious problems on the separation between the metal and the slag. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process with iron ore bearing titania. In this study, the formation of Ti(C,N) in blast furnace and the influences of various factors on the Ti(C,N) formation are investigated by FactSage. It is found that the mass of Ti(C,N) would reach the maximum at 1480 oC, and the product is mainly TiN below 1620 oC, while it is mainly TiC above 1620oC. The order of the factors by the importance from strong to weak was: temperature, the content of TiO2 in slag, basicity of slag, the content of MgO and Al2O3.IntroductionThe titanium dioxide (TiO2) in iron ore bearing titania will be partly reduced by carbon to titanium carbonitride (Ti(C,N)) in blast furnace, causing serious problems on the separation between the metal and the slag because of the change of flow property. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process, especially for the smelting of iron ore bearing titania. Extensive experimental data in regard to the formation of Ti(C,N) has been reported in numerous papers[1-6]. However, only some discrete data can be obtained by experiment, and it is difficult to detect the mass of Ti(C,N) in slag. In addition, the experiment is difficult to be proceeded when the temperature is above 1600oC. Therefore, it is very difficult to make clear the critical condition of the formation of Ti(C,N) by experiment."

Jan 1, 2012

By Patrick R. Taylor

Keywords: Thermal Plasma, Electroreduction, Electrolysis, Transition metals, Waste treatment, Molten oxides, Chromium oxide. An innovative process to treat transition metal oxide waste materials from diverse sources is presented. This technology involves using reverse-polarity DC plasma driven electrolysis in molten oxides. The process results in the recovery of the transition metal and other heavy metals from waste. By-products generated throughout the processing was converted to environmentally acceptable slag. The significance of this technology is that the treatment of the waste is accomplished in one step which in turn lowers the cost of remediation. Moreover, this process uses high temperature properties of thermal plasmas, which makes it possible to use molten oxides instead of halides as electrolytes. Chromium was successfully reduced from chromium oxide through the plasma driven electro-reduction process. It was shown that the selection of the appropriate ionic conducting oxides was critical for the formation of a slag that would enhance the reduction of chromium oxide.

Jan 1, 2004

By Kenneth McGowan

"The aluminum industry is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating accounts for 25% of the energy consumed to manufacture aluminum. Consequently, the generation of this energy results in the production of a significant amount of CO2 (over 3.75 million metric tons in 2003)1. As a result, the Aluminum Industry Technology Roadmap of 2003 listed the development of improved refractory materials as a goal to reduce energy use and decrease greenhouse gas creation. The result of a R&D effort addressing this desire is the development of patented microporous refractory materials for metal contact applications in all furnace areas including the belly band. It has been demonstrated that this material can reduce energy consumption up to 38% in furnaces and significantly reduce heat loss in launder and trough systems. Furthermore the material developed is non-wetting and remains un-penetrated by metal throughout its lifetime. The material does not contribute to the formation of corundum. As a result, the energy efficiency of an older lining remains intact compared to standard refractory materials which may have an initial high insulating value (such as lightweights and board) or standard dense refractory (even with penetration inhibitors) both of which show a rapid increase in thermal conductivity as the refractory is penetrated with aluminum and formed corundumIntroductionThe aluminum industry is the second largest producer of metal in the United States, behind the iron and steel industry. It is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating is required to melt, hold, purify, alloy, and heat treat the metal and accounts for 25% of the energy consumed to manufacture aluminum. As such, process heating is the second largest energy consuming operation. Smelting, which utilizes an electrolytic reduction process is the largest energy consuming operation1.Most process heating is accomplished through the use of fossil fuels, either directly or indirectly. The choice of fuel is dependent on a plant’s location and fossil fuel availability. Table I shows the processes impacted by refractories and the calculated BTU’s generated by usage of the respective fuels as well as the Metric Tons (MT) of metal passed through each process in 20001."

Jan 1, 2009

By Dominik Hofer

A broad spectrum of tantalum containing input materials can be processed for the production of synthetic tantalum concentrate (“SynCon”). The use of these low grade substances offers a secure alternative to mining of coltan in Central Africa. SynCon is produced in a multi-stage pyrometallurgical process, wherefore the melting behaviour of slags presents an important factor especially regarding the energy consumption and its optimisation. The characteristics of a slag comprising mostly Al2O3, CaO, SiO2 and MgO are influenced by the amount of other oxidic constituents which enfolds the main focus of this study. A hot stage microscope serves for the investigation of the slag behaviour in a temperature range from 1000 to 1600 °C under reducing atmosphere (CO/CO2 gas). The experimental results are compared with thermodynamic calculations (FactSage) to get a better understanding of the process.

By Nickolas J. Themelis

The flash oxidation and smelting of mineral sulfides is a very prominent metallurgical achievement of the second part of this century. Its initial industrial implementation owes much to the work of Petri Bryk, in Finland, and Paul Queneau, in Canada. However, attempts to develop flash reduction pro- cesses, such as the reduction of iron oxide concentrates with hydrogen, have not yet been successful. The author, on the basis of experimental studies on both kinds of flash reaction systems, examines the respective rate controlling phenomena and the relative rates of flash oxidation and flash reduction.

Jan 1, 1993

By A. G. Jackson, S. J. P. Laube

"Control of thin films during the growth process is dependent on several parameters that are difficult to monitor, including flux of film material, pressure, substrate temperature, composition, and thickness. One means for easing this difficulty is to take advantage of emission spectra associated with the process and the film. For pulsed laser deposition (PLD), the ion cloud generated by the laser has characteristic emission spectra that can be used to control the flux and, hence, the film. For chemical vapor deposition, the species present can be determined using mass spectroscopy and specific peaks can be used to control the deposition. Raman spectroscopy affords the possibility of real-time control by sensing characteristic peaks associated with film composition and thickness. These spectroscopic methods offer a real-time alternative to process control that is very attractive, because of the ability to accurately control films to achieve the engineered structures and properties sought. Examples are presented to illustrate the capabilities of these methods for thin film preparation.IntroductionThe drive to reduce costs and improve efficiencies of operation sets the tone for much of research, basic or applied. Basic research is limited by the ability of sensors and associated instrumentation to measure parameters accurately and reproducibly. Applied research has the same limitations and also the added constraints of time and costs. Hence, there are strong incentives to explore means for refining existing sensors with respect to performance and cost, as well as finding new sensors and techniques for more accurately and rapidly measuring quantities of interest in experiments and in various processes."

Jan 1, 1997

By Samantha Moodley, Rauf Hurman Eric, Cevat Kucukkaragoz, Aditya Kale

"Two titania slags, rutile and synthetic rutile were chlorinated with petroleum coke and CO in a small bubbling fluidized bed reactor. The study aims to identify differences in chlorination mechanism, compare conversion rates, blowover and the chlorination of impurities for the various titania feedstocks at different temperatures.Chlorination rates were highest at 1000ºC; rutile chlorination significantly increases as temperature increases from 800ºC to 1000ºC. At 1000ºC, synthetic rutile had the highest chlorination conversion rate; this was followed by Slag B which in turn was more reactive than Slag A and rutile. The mechanism for slag, synthetic rutile (SR) and rutile chlorination differs. Synthetic rutile feed is porous, providing a larger surface area for the chlorination reaction, hence the highest conversion rates was attained. Titania slag becomes porous with the initial chlorination of FeO and MnO whilst rutile remains solid. As the porosity of slag particles increases so does its tendency to be elutriated. Ti2O3 is oxidized within the early stages of chlorination during the chlorination of FeO and MnO. Ti2O3 not oxidized is then rapidly chlorinated.IntroductionTitanium dioxide (TiO2) is the most common compound of titanium, about 95 - 98% of extracted titanium minerals is processed into TiO2 white pigment [1]. Two processing routes exist for the production of TiO2 pigments, i.e., sulphate and chloride based processes. In the chloride process, titania feedstock is fed to a fluidized bed reactor together with reductant and chlorine gas. A temperature of 1000 - 1300ºC is maintained in the reaction zone and apart from silica, zirconia, uranium and thorium, virtually all the metal oxides in the feed are converted to their respective chlorides [2]. Chlorine is recovered and recycled back to the reactor."

Jan 1, 2012

By Kimio Itagaki

The distribution ratios of Ag, Pb, As, Sb and Bi for the Cu2S-FeS or Ni3S2-FeS matte / FeOx SiO2, FeOx-SiO2-CaO or FeOx-CaO slag equilibration in a MgO crucible were determined experimentally at 1523~1573K under controlled partial pressures of S2 and O2 at given PSO2 of 10.1, 50.7 and 101.3 kPa (0.1, 0.5 and 1 atm) and be observed dependency of distribution ratio on the matte grade, SO2 pressure and slag basicity were analyzed on the basis of thermodynamics,

Jan 1, 2003

By Joseph C. Rota

The Carlin Trend is one of the most significant gold mining districts in North America. Located in northeastern Nevada, a total of over 17 million ounces of gold have been produced since 1965 at Newmont Gold Company's open-pit and underground operations. Oxidized portions of the sediment-hosted, disseminated gold deposits at Carlin generally consist of finely disseminated concentrations of sub-micron sized native gold particles hosted in Paleozoic siliciclastic or carbonate rock. Oxide ore is commonly amenable to dump leach or heap leach processing, yielding an average 50 to 70% recovery of total contained gold. Refractory unoxidized ore requires some form of pretreatment oxidation to ensure economic gold recovery. Geologic ore control is typically combined with standard assay and engineering techniques to maintain both grade and metallurgical control ofleach grade ores. Mine geologists provide a vital function through field observation and recording ofmineralogic data during daily, visual blasthole logging. Intricately mixed refractory materials must be separated from oxide ore to ensure highest possible gold recoveries. Geologic information is combined with assay data to create mine polygons in an engineering computer database. Mining selectivity is further enhanced by in-pit ore control geologists who are available to make production decisions based on direct mineralogic observations at active mine faces.

Jan 1, 1997

By Guan-zhou Qiu, Shui-shi Liu, Yu-feng Guo, Tao Jiang

"The preparation of high-quality synthetic ruitle from electric furnace titanium slag was systematically investigated by activation roasting followed by acid leaching process. The results showed that impurities such as Ca and Mg in titanium slag can be effectively removed and TiO2 grade of the product was markedly improved by the process. High-quality synthetic rutile containing 88.54% TiO2, 0.42% (CaO+MgO) was obtained under the conditions that roasted with 7.5%(wt) H3PO4 at 1000 oC for 2h, followed by two-stage leaching in boiling dilute sulfuric acid for 2h. Mechanism studies showed that anosovite solid solution and silicate minerals were reacted with phosphoric acid in the roasting process. As a result, titanium components in titanium slag turned into rutile (TiO2) and impurities were transformed into acid-soluble phosphate and quartz.IntroductionWith the gradual depletion of natural rutile and the rapid development of titanium industry in China, the natural rutile reserves cannot satisfy the requirement for production of titanium pigment and titanium sponge. Ilmenite is, therefore, becoming main raw material for titanium industry. However, because of its low TiO2 grade, it generally requires preconcentration to titanium-rich material such as titanium slag or synthetic rutile [1-3].Ilmenite resources are extremely rich in Pan-xi area of China, which account for 90.54% of total ilmenite reserves in China [4]. The titanium slag produced by electric smelting of ilmenite concentrate has high contents of Ca and Mg, and is not suitable as a raw material for chloride process and titanium sponge production. Therefore, upgrading titanium slag to prepare raw material suitable for chloride process and titanium sponge production has important significance for the development of China's titanium industry."

Jan 1, 2011

By Li Ma, Shaoguo Chen, Gele Qing, Qihang Liu, Keng Wu

Olivine contains higher MgO element, which can be added into blast furnace burden to improve slag stability and fluidity. Effect of calcined olivine and untreated olivine on low silicon pellet production process and quality was studied in this paper. The results shows, calcined olivine has no effect on bursting temperature of green pellet, however the bursting temperature of green pellet will decrease with increase of untreated olivine ratio. Untreated olivine has slight effect on green pellet strength than calcined olivine while the ratio is higher than 2%. The compressive strength of low silicon pellet will increase first and decrease afterwards with increases of calcined olivine ratio under firing temperature of 1250°C, whereas, the changing sequence is reverse fired under 1280°C. The result of untreated olivine pellet compressive strength is same as calcined olivine pellet. However, the compressive strength and metallurgical property of calcined olivine pellet is slightly higher than that of untreated olivine pellet under same condition.

Jan 1, 2015

By Jari Aromaa, Antti Kekki, Olof Forsén

"The deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential depends on surface morphology, surface film resistance and additives on cathode surface. The effects of surface properties on copper nucleation and growth rates were studied for used stainless steel blanks from several tankhouses. The surfaces of the blanks were characterized with electrochemical and mechanical methods. Electrochemical deposition tests were done at current density of 300 A/m2 for 10, 30 and 60 seconds. The nucleation density and copper coverage were estimated using image analysis. The surface film resistance did not correlate with copper growth. Increasing surface roughness correlated with lower copper growth.IntroductionStainless steel cathode blanks in copper electrorefming are usually made of AISI 3 I6L type steel. They have a typical lifetime over 10 years. During use the surface will collect deposits and become rough due to wear and corrosion. These factors can affect the nucleation and growth of copper. The nucleation and deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential can depend on surface film resistance, surface morphology, and additives adsorbed on cathode surface.The deposition potential of metallic ions on a foreign substrate is usually higher than the deposition potential on the electrode made of the same metal due to crystallographic substrate/metal misfit [I]. If the substrate has traces of the depositing metal they will be preferential growth sites. For a smooth deposit a large number of simultaneous nuclei is necessary. However, excessive nucleation density can lead to porous deposits [2]. Surface films of good conductivity are needed for dense nucleation and small nuclei. On cathode blanks the number of active sites increases with increasing surface film conductivity [3-5] and/or surface film porosity [6]. On AISI 3 I6 L stainless steel a more resistive oxide has been found to limit favourable sites for copper nucleation and more conductive film promoted high-density copper nucleation [7]. Also Urda-Kiel et al. have concluded that thicker oxide layers on AISI 304 stainless steel resulted in lower nucleation [8]. Increase in overpotential or current density activates more and more of the potential nucleation sites and this can be seen as higher number of nuclei [9] or smaller average distance between nuclei [10]."

Jan 1, 2012

By R. Shimpo

Equilibrium calculations by a computer may sometimes fail in giving solutions when the system includes a large number of components and more than three phases, and especially when no definite information about stable phases is given. An improved method of calculation is presented in which the number of phases need not to be initially fixed, phases can appear or disappear in the course of' calculation and a new method is combined with the Newton-Raphson method to obtain solutions easily. The improved method is applied to the copper smelting operation and all the successive stages of the operation are successfully simulated.

Jan 1, 1983

By Willy Persson

A common feature of the kinds and amounts of impurities present most pyrometallurgical, processes is injection of oxygen to, remove various in the feed. The degree of success of a specific process step relies critically on control of the instantaneous oxygen potential/oxidation stage, throughout the step as well as upon termination of the step. This will, for instance, determine the distribution of impurities between metal and slag. As long as the operation is perturbation free -detailed analysis of all additions and application of advanced models often yield satisfactory control means However, a pyrometallurgical process is seldom free from disturbances, which reduces the accuracy of the static models and leads to inconsistencies in scheduled route might be uncontrollable changes in quality and quantity of feed, operator interventions and shift changes, timing of cranes, lining wear and accretions etc. The implementation of dynamic, control to correct for disturbances and, more generally for process optimization, requires continuous on-line information on, the actual status of the process. The implementation of sensors for continuous process monitoring, e.g., as regards the instantaneously prevailing oxygen potential or oxidation stage, has been hampered by the highly aggressive environment in smelters; This is. where remote-sensing techniques based on optics and spectroscopy, have proven to form invaluable, tools towards the realization of dynamic production control. Since about 15 years Semtch has developed and industrialized a remote-sensing technology, based on ,optics and spectroscopy, for continuous on-line process monitoring and production control of various pyrometallurgical processes. The presentation will discuss applicability aspects with examples and experiences from installations and tests in ferrous and non-ferrous industry. Keywords: Applied spectroscopy, Metallurgy, Process monitoring, Production. Control

Jan 1, 2003

By Guan-Yong SHI, Cong Wang, Zhi-he DOU, Ting-an ZHANG, Shi-gang FAN

Based on the pre-works, this paper proposed a new short stage process of the intensify aluminothermy reduction by the stage to prepare high titanium ferroalloy with low O and Al contents. We investigated the effects of Al and Ca and Si combination reduction agent, slag type and step-up reduction conditions on the Al content and distribution in the alloy. The results show that the step-up reduction can not only reduce effectively the oxygen content in the alloy, but also reduce effectively Al content. For instance, the oxygen content in high titanium ferroalloy is within 1%~4%, and the Al content is within 1%~5%. Its quality reaches the requirement of high titanium ferroalloy prepared by remelting process.

Jan 1, 2015

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of synthetic rutile—a common starting material for most titanium production processes—from iron-rich titanium minerals such as pseudorutile and ilmenite is described. The process for “upgrading” the mineral to synthetic rutile is by carbothermal reduction of the mineral while immersed in a molten salt at high temperature, followed by magnetic separation of the reduced iron. A variety of factors are also investigated, such as particle size of the mineral, the type of mineral, and the molten salt used. The solubility of iron(III) oxide in different molten salts is also experimentally determined.

Jan 1, 2016