Search Documents

By Michael L. Free

Bacterial oxidation of an arsenopyritic gold-ore .concentrate was carried out with continuous-flow .operation in 14-liter, mechanically agitated reactors. Samples from the slurry reactors were separated into solid and liquid fractions and analyzed separately to determine the electrochemical rates of sulfide conversion by the bacteria and the rates of direct bacterial oxidation of sulfide. The rates of the individual mechanisms are compared to the overall rates of biooxidation in the continuous-flow slurry reactors. The results show that the commonly hypothesize4 direct and indirect mechanisms of biooxidation both play a significant role in the bacterial oxidation of sulfide ores.

Jan 1, 1991

By Cheng Yan, Yugang Li, Qian Wang, Lizhi Zhang

In continuous casting process, mold powder has lots of metallurgical effects, such as covering the molten steel to prevent liquid steel from oxidation by air, preserving heat for top layer liquid steel, lubricating initial shell and so on. However, mold powder also can deteriorate the quality of final products obviously after the entrapment of mold powder in steel. In the present work, based on the similarity theory the effect of technological parameters on mold powder entrainment was investigated by water model. Experiment was carried out in the water mold using oil and water to simulate slag and steel, respectively. The results showed that increasing casting speed increased the water-oil interfacial fluctuation and entrainment frequency; viscosity of oil also had a great impact on the interface fluctuation and entrainment; water-oil interfacial tension effect the entrainment while not changing the interfacial fluctuation; submergence depth had little impact on entrainment and interfacial fluctuation.

Jan 1, 2015

By Byung-Su Kim

The reaction between calcium sulfate and hydrogen is of interest both as a means of regenerating calcium sulfide as a reductant of sulhr dioxide to elemental sulhr and for producing elemental sulhr from gypsum. This reaction was investigated using a thermogravimetric analysis technique in the absence and presence of nickel catalyst. The reaction temperature was varied between 973 and 1153 K, while the hydrogen partial pressures of 12.9 - 86.1 kPa were utilized. At 1073 K and a hydrogen partial pressure of 86.1 kPa, 60 % of the original calcium sulfate in the absence, and 95 % in the presence, of the nickel catalyst was converted to calcium sulfide in one hour.

Jan 1, 1999

By M. K. Yelloji Roa

Effect of conditioning with Thiobacillus ferrooxidans on the floatability of sphaierite and galena has been determined in this work. The flotation behavior of the conditioned minerals clearly shows that such bacterial conditioning does produce marked modification of their surfaces. The variables affecting the surface modification and thereby the flotation response of the minerals were found to be cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Importantly, while the enhancement in flotation obtained due to sulphuric acid treatment was retarded by biotreatment in the case of galena at all cell concentrations due to electrochemical effects, such decrease occurred in the case of sphalerite only at cell concentration sufficiently high for their attachment to the mineral surface. The effect of bacterial conditioning has significant implications to the differential flotation of sphalerite and galena. Mechanisms responsible for the modification of the surface properties of these sulphides due, to bacterial conditioning are discussed.

Jan 1, 1991

By W. G. Davenport

Chapter 4 examined Inco (oxygen) flash smelting of pure chalcopyrite concentrate. It showed that the oxygen and flux requirements for auto thermal smelting are readily determined by a matrix calculation. This chapter extends this matrix approach by applying it to a multi-mineral concentrate.

Jan 1, 2001

By Yuzuru Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about 1880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By Bogidar V. Mihaylov

Bacterial oxidation of a low-grade sulfide gold ore was investigated in order to enhance leaching of gold. The experiments were carried out in columns using mixed cultures of Thiobacillus ferrooxidansisolated from the ore. Fractions with different screen analyses were oxidized in two regimes - one pass of the solution and circulating, solution. Constant temperature and flow-rate of the percolating solution were maintained during the experiments. A correlation between the concentrations of copper and iron in the solution leaving the columns and pH and Eh values was observed. The effect of bacterial activity was proved by means of thiourea and cyanide leaching of the oxidized ore.

Jan 1, 1991

By Hubert Bril, Priscilla Pareuil, François Bordas, Emmanuel Joussein, Jean-Claude Bollinger

"According to the legislation, valorization type, origin and characteristics of waste material, various standard procedures are available to evaluate environmental impacts. A Mn-rich slag was sampled from a metallurgical plant. After its characterization (elementary analysis and mineralogy), five standard procedures were carried out (i.e. TCLP, EN 12457-1). Each fixed parameter of the standards was systematically studied in a large range: pH, Liquid/Solid ratio, contact time. For example, EN 12457-1 led to a low ME mobilization, increasing with the L/S ratio, the contact time and an acidic pH. As a conclusion, the representativeness of the considered parameters and their potential variations are predominant to assess of the real environmental impact during slag reuse. Introduction Recent studies have been carried out about environmental impacts of waste containing metallic elements (ME) because of their potential mobility [1-7]. Indeed, slags are either dumped or valorized in various activities such as building materials. In order to assess environmental risk, various standard procedures are used depending on country legislation, origin of waste and valorization way. Results of leaching tests are linked either to special legislation (e.g. Dumping: EC, Council Decision 2003/33/EC, Construction products: EC, Council Directive 89/106/EEC) or to legal levels used in drinking water (Directive 98/83/CE) when leachates could migrate to groundwater. If ME in leachates are lower than drinking water authorized levels, the waste will be considered as non-hazardous. On the contrary, if the leachable amounts exceed them, the question about the risk has to be posed. Beyond the abundance of leaching tests available, variety of operational conditions induced by these regulatory tests does not make the choice easier. According to operational conditions induced, ME release could vary from one test to another one. ME concentrations in leachates depend on pH, Liquid/Solid ratio, contact time and particle size [3]. To highlight the importance of these operational parameters, potential risk for valorization of a manganese-rich slag was assessed by comparing several standard leaching protocols [8-12] with a global study dealing with the influence of operational conditions. For each regulatory protocol, the most influential parameters (L/S ratio, pH, particle size and contact time) have been studied in a large range."

Jan 1, 2008

By B. Yawney

A copper-nickel sulfide concentrate was leached in water at about 2000C under oxygen pressures of about 0.35 MPa. Oxidation of sulfide to sulfate was virtually complete in about 30 minutes, resulting in greater than 95% copper and 98% nickel extractions. Leaching temperature was shown to be the most important factor affecting metal extractions. Measured rates of oxygen consumption were used to develop batch kinetic data. Mini-plant continuous pressure leaching tests agreed with batch leach results. A proposed overall flowsheet is briefly examined.

Jan 1, 1976

By Ronald Klepper

In hydrometallurgy, pure gases like oxygen and hydrogen are used for oxidation and reduction. The gases are expensive and therefore should be used efficiently. Non reacted gas can be recycled into the liquid. Historically vortex gassing has been used; Le. a mixing impeller close to the liquid surface entrains gas from the headspace into the liquid through a gas vortex. Novel and more efficient methods are surface gassing with up pumping impellers and self- inducing gassing impellers. These alternative impeller systems are well established and common in the chemical industry, but have not been used until recently in hydrometallurgy. Gassing impellers act as internal compressors and increase the interfacial surface for a much higher mass transfer compared to alternate methods mentioned. In the paper results from lab and pilot tests and data from operated plants will be presented. The reactions with gases normally take place under moderate to high pressure, therefore a safe enclosure with mechanical seals and the safety "philosophy" is important. Experienced life and replacement cycles will be reported.

Jan 1, 2000

By Tuneo Funahashi

Sumitomo Shisaka Works has been treating EAF(Electric Arc Furnace) dust to recover zinc and lead in the Waelz Kiln process. Since its commencement of operation in 1977, many technical improvements have been successfully made to increase the production capacity and the zinc recovery rate. The EAF dust charge to the Waelz Kiln was increased from 35,000tly to 120,00OtIy, and the production of zinc oxide now amounts to 40,000tly. The zinc content in the clinker was decreased from 5% to less than I%, by the optimization of the kiln heat pattern with no accretion trouble. And the clinker has become more a valuable raw material for steel making. This paper describes the above progress ofthe SMM Waelz Kiln process operation at the Shisaka Works.

Jan 1, 1998

By Susumu Okabe

Top blowing lances are employed by the Mitsubishi Continuous Copper Converter for the continuous supply Of reaction gases into moken bath. In order to minimize the refractory wear caused by the interaction between the furnace lining and the melt splash. optimum furnace design and blowing condition are? required. An empirical equation obtained by the physical model study enables the estimation of the splashing rate on a vel1ical plane at a certain distance from the lance.

Jan 1, 1996

By J. W. A. Morris

To investigate the use of centrifugal fields in fused salt electrowinning cells, a high temperature rig has been designed, constructed and commissioned. Initially, the cell has been applied to the fused salt electrowinning of zinc. Current efficiencies of 93% have been obtained for inter electrode gaps as small as 8mm for 70mm diameter electrodes rotating at 100rpm. The construction of a semi-rigorous physical model has shown the potential exists to extend the use of centrifugal fields to the electrowinning of light metals.

Jan 1, 1994

By Stavros A. Argyropoulos, Henry H. Hu

"The assimilation of exothermic additions in liquid metals exhibit an array of unique coupled heat, mass and momentum transport phenomena. These phenomena are further complicated by the presence of a moving boundary.This paper describes a) A mathematical model which simulates the complex phenomena, and b) An extensive verification of the mathematical model. The SIMPLER algorithm was employed to solve numerically the pertinent partial differential equations. The computational results indicated that the exothermic heat of mixing led to a rapid increase in temperature around the moving boundary, which produced an enhanced convective flow in the liquid phase. The intensification of fluid flow around the moving boundary resulted in an acceleration of the melting process.Verification of the model was carried out in two contexts. The first was, in a low temperature physical model consisting of ice immersion in different sulfuric acid solutions. In this physical model, both temperature and velocity measurements were carried out. The model results were compared with experimental measurements and they were found to be in excellent agreement. The second context employed high temperatures, involving the assimilation of silicon in high carbon liquid iron. The model was also applied to predict fluid flow, heat and mass transfer for these high temperature experiments and a good agreement was obtained.In addition new dimensionless heat transfer correlations that quantify these complex phenomena will be presented."

Jan 1, 2001

By M. GONZALES-FERNANDES M

Natural rubber/organophilic clay nanocomposites were prepared and characterized. A brown bentonite from Paraiba’s State, Brazil was modified with a sodium salt and treated with quaternary ammonium salt hexadecyltrimethyl ammonium chloride. The clay in its natural state, after cation exchange with sodium and after organophilization was characterized by XRD, IR, SEM, thermal analysis. Nanocomposite samples were prepared containing 10 resin percent of organophilic clay. The vulcanized samples were analyzed by XRD, SEM. The nanocomposites obtained showed improvement in their mechanical properties in comparison with samples without clay.

Jan 1, 2015

By V. B. Chernyavsky, Ladokhin S. V.

Equipment and continuous casting technology for the production of small diameter copper rods and tubes are described. Industrial copper wastes, such as scrap and shavings, were used as the charge. An electron-beam installation for rod and tube production includes a crucible with an electromagnetic stirring system and a pouring hole in its bottom, a bottomless mold, .and a special cooling system, which includes an oil and water cooling devices. For the first time in the electron-beam technology, rods of 8 mm and 14 mm diameter mm tubes of 14 mm external diameter and 7 mm internal diameter were produced through continuous casting by pulling them out of the vacuum chamder into the atmosphere with depressurizing the vacuum chamber. The production capacity of a single strand continuous casting machine was 200 mm/tnin for rod casting and 150 mm/min for tube casting.

Jan 1, 2000

By Alana Pereira Ramos, Walman Benicio de Castro

Amorphization and martensitic transformation (Ms) characteristics of Ti–Ni-Cu alloy ribbons prepared by melt spinning were investigated by means of differential scanning calorimetry and X-ray diffraction. In these experiments particular attention has been paid to change the wheel linear velocity from 21 to 63 m/s. Then the cooling rates of ribbons were controlled. The effect of this cooling rate and alloy composition on martensitic transformation behavior is discussed.

Jan 1, 2015

By James D. Navratil

Although liquid membranes have several advantages over conventional liquid-liquid extraction, problems such as membrane instability remain. In order to solve these problems, we have combined an electrostatic field with the principle of liquid membranes and developed a novel reactor system for rare earth recovery. Our cylindrical reactor, filled with extractant and diluent, is divided by means of a perforated cylinder into an outer annular extraction cell and an inner stripping cell. Below the extraction and stripping cells are two settlers for the aqueous solutions. The design of the reactor permits the organic solution to flow freely through the special perforated cylinder and the added feed and strip solutions, outside and inside the perforation, respectively, to be completely separated.

Jan 1, 1990

By J. C. Agarwal

Do large-scale projects in mining and smelting start up and achieve expected capacity on schedule? In most cases not. Regardless of worldwide location, company know-how, or financial backing, unforeseen delays occur. A comprehensive CRA study for the World Bank shows that delays are the rule, not the exception, in most mining and smelting projects. When delays are not factored into analysis and planning, financial projections are, literally, not to be believed. Returns on investment will seldom achieve their targeted level because of startup delays. This paper reviews the results of our analysis of startup of new mines, mills, and smelters; provides a detailed discussion of why delays occur in the smelters and refineries; presents the cash flow implications of startup delays; and discusses preventive measures that should be taken to avoid financial shortfalls,

Jan 1, 1983

By M. S. Lee

A cold model study on the effects of various operating conditions on the dispersed-phase holdup in a liquid-liquid emulsion generated by bottom gas injection has been performed using water and kerosene. Dimensional analysis was used to correlate the holdup with the operating conditions and the sampling locations. The holdup increased with gas velocity, and decreased with axial and radial distances. The radial distribution of holdup follows a Gaussian function. The holdup increased with increasing ratio of the heavy phase to light phase volumes and decreased with the total height of the heavy phase. The combined effects of various operating conditions can be represented by the Froude number. The variation of the holdup within the plume was correlated by a single equation involving a set of dimensionless numbers.

Jan 1, 1995